| Age | Commit message (Collapse) | Author |
|---|
|
In smc_cdc_msg_recv_action() the received cdc message is evaluated.
To reduce the number of messaged triggered by this evaluation the logic
is streamlined. For the write_blocked condition we do not need to send
a response immediately. The remaining conditions can be put together
into one if clause.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When no free transfer buffers are available then a work to call
smc_tx_work() is scheduled. Set the schedule delay to zero, because for
the out-of-buffers condition the work can start immediately and will
block in the called function smc_wr_tx_get_free_slot(), waiting for free
buffers.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the call to smc_close_wake_tx_prepared() (which wakes up a possibly
waiting close processing that might wait for 'all data sent') to
smc_tx_sndbuf_nonempty() (which is the main function to send data).
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an updated rx_cursor_confirmed field was sent to the peer then
reset the cons_curs_upd_req flag. And remove the duplicate reset and
cursor update in smc_tx_consumer_update().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bitmap of found partitions in efx_ef10_mtd_probe was not
initialised, causing partitions to be suppressed based off whatever
value was in the bitmap at the start.
Fixes: 3366463513f5 ("sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just a few fixes:
* aggregation session teardown with internal TXQs was
continuing to send some frames marked as aggregation,
fix from Ilan
* IBSS join was missed during firmware restart, should
such a thing happen
* speculative execution based on the return value of
cfg80211_classify8021d() - which is controlled by the
sender of the packet - could be problematic in some
code using it, prevent it
* a few peer measurement fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent cls_flower offload rewrite added a double new line.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
floppy_check_events() is supposed to return bit flags to say which
events occured. We should return zero to say that no event flags are
set. Only BIT(0) and BIT(1) are used in the caller. And .check_events
interface also expect to return an unsigned int value.
However, after commit a0c80efe5956, it may return -EINTR (-4u).
Here, both BIT(0) and BIT(1) are cleared. So this patch shouldn't
affect runtime, but it obviously is still worth fixing.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: a0c80efe5956 ("floppy: fix lock_fdc() signal handling")
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently bpf_offload_dev does not have any priv pointer, forcing
the drivers to work backwards from the netdev in program metadata.
This is not great given programs are conceptually associated with
the offload device, and it means one or two unnecessary deferences.
Add a priv pointer to bpf_offload_dev.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
This patch adds missing information about feature-subcommand in
bpftool.rst
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Starting from opregion version 2.1 (roughly corresponding to ICL+) the
RVDA field is relative from the beginning of opregion, not absolute
address.
Fix the error path while at it.
v2: Make relative vs. absolute conditional on the opregion version,
bumped for the purpose. Turned out there are machines relying on
absolute RVDA in the wild.
v3: Fix the version checks
Fixes: 04ebaadb9f2d ("drm/i915/opregion: handle VBT sizes bigger than 6 KB")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208184254.24123-2-jani.nikula@intel.com
(cherry picked from commit a0f52c3d357af218a9c1f7cd906ab70426176a1a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The u32 version field encodes major, minor, revision and reserved. We've
basically been checking for any non-zero version.
Add opregion version logging while at it.
v2: Fix the fix of the version check
Fixes: 04ebaadb9f2d ("drm/i915/opregion: handle VBT sizes bigger than 6 KB")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208184254.24123-1-jani.nikula@intel.com
(cherry picked from commit 98fdaaca9537b997062f1abc0aa87c61b50ce40a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Make sure the underlying VMA in the process address space is the
same as it was during vm_mmap to avoid applying WC to wrong VMA.
A more long-term solution would be to have vm_mmap_locked variant
in linux/mmap.h for when caller wants to hold mmap_sem for an
extended duration.
v2:
- Refactor the compare function
Fixes: 1816f9236303 ("drm/i915: Support creation of unbound wc user mappings for objects")
Reported-by: Adam Zabrocki <adamza@microsoft.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.0+
Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Adam Zabrocki <adamza@microsoft.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20190207085454.10598-1-joonas.lahtinen@linux.intel.com
(cherry picked from commit 5c4604e757ba9b193b09768d75a7d2105a5b883f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
When resuming, we check whether or not any previously connected
MST topologies are still present and if so, attempt to resume them. If
this fails, we disable said MST topologies and fire off a hotplug event
so that userspace knows to reprobe.
However, sending a hotplug event involves calling
drm_fb_helper_hotplug_event(), which in turn results in fbcon doing a
connector reprobe in the caller's thread - something we can't do at the
point in which i915 calls drm_dp_mst_topology_mgr_resume() since
hotplugging hasn't been fully initialized yet.
This currently causes some rather subtle but fatal issues. For example,
on my T480s the laptop dock connected to it usually disappears during a
suspend cycle, and comes back up a short while after the system has been
resumed. This guarantees pretty much every suspend and resume cycle,
drm_dp_mst_topology_mgr_set_mst(mgr, false); will be caused and in turn,
a connector hotplug will occur. Now it's Rute Goldberg time: when the
connector hotplug occurs, i915 reprobes /all/ of the connectors,
including eDP. However, eDP probing requires that we power on the panel
VDD which in turn, grabs a wakeref to the appropriate power domain on
the GPU (on my T480s, this is the PORT_DDI_A_IO domain). This is where
things start breaking, since this all happens before
intel_power_domains_enable() is called we end up leaking the wakeref
that was acquired and never releasing it later. Come next suspend/resume
cycle, this causes us to fail to shut down the GPU properly, which
causes it not to resume properly and die a horrible complicated death.
(as a note: this only happens when there's both an eDP panel and MST
topology connected which is removed mid-suspend. One or the other seems
to always be OK).
We could try to fix the VDD wakeref leak, but this doesn't seem like
it's worth it at all since we aren't able to handle hotplug detection
while resuming anyway. So, let's go with a more robust solution inspired
by nouveau: block fbdev from handling hotplug events until we resume
fbdev. This allows us to still send sysfs hotplug events to be handled
later by user space while we're resuming, while also preventing us from
actually processing any hotplug events we receive until it's safe.
This fixes the wakeref leak observed on the T480s and as such, also
fixes suspend/resume with MST topologies connected on this machine.
Changes since v2:
* Don't call drm_fb_helper_hotplug_event() under lock, do it after lock
(Chris Wilson)
* Don't call drm_fb_helper_hotplug_event() in
intel_fbdev_output_poll_changed() under lock (Chris Wilson)
* Always set ifbdev->hpd_waiting (Chris Wilson)
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 0e32b39ceed6 ("drm/i915: add DP 1.2 MST support (v0.7)")
Cc: Todd Previte <tprevite@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v3.17+
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190129191001.442-2-lyude@redhat.com
(cherry picked from commit fe5ec65668cdaa4348631d8ce1766eed43b33c10)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Enable count array is supposed to have one counter for each possible
engine sampler. As such, array sizing and bounds checking is not correct
and would blow up the asserts if more samplers were added.
No ill-effect in the current code base but lets fix it for correctness.
At the same time tidy the assert for readability and robustness.
v2:
* One check per assert. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b46a33e271ed ("drm/i915/pmu: Expose a PMU interface for perf queries")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190205130353.21105-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 26a11deea685b41a43edb513194718aa1f461c9a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
ipvs relies on nf_defrag_ipv6 module to manage IPv6 fragmentation,
but lacks proper Kconfig dependencies and does not explicitly
request defrag features.
As a result, if netfilter hooks are not loaded, when IPv6 fragmented
packet are handled by ipvs only the first fragment makes through.
Fix it properly declaring the dependency on Kconfig and registering
netfilter hooks on ip_vs_add_service() and ip_vs_new_dest().
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
__nf_conntrack_confirm
For bridge(br_flood) or broadcast/multicast packets, they could clone
skb with unconfirmed conntrack which break the rule that unconfirmed
skb->_nfct is never shared. With nfqueue running on my system, the race
can be easily reproduced with following warning calltrace:
[13257.707525] CPU: 0 PID: 12132 Comm: main Tainted: P W 4.4.60 #7744
[13257.707568] Hardware name: Qualcomm (Flattened Device Tree)
[13257.714700] [<c021f6dc>] (unwind_backtrace) from [<c021bce8>] (show_stack+0x10/0x14)
[13257.720253] [<c021bce8>] (show_stack) from [<c0449e10>] (dump_stack+0x94/0xa8)
[13257.728240] [<c0449e10>] (dump_stack) from [<c022a7e0>] (warn_slowpath_common+0x94/0xb0)
[13257.735268] [<c022a7e0>] (warn_slowpath_common) from [<c022a898>] (warn_slowpath_null+0x1c/0x24)
[13257.743519] [<c022a898>] (warn_slowpath_null) from [<c06ee450>] (__nf_conntrack_confirm+0xa8/0x618)
[13257.752284] [<c06ee450>] (__nf_conntrack_confirm) from [<c0772670>] (ipv4_confirm+0xb8/0xfc)
[13257.761049] [<c0772670>] (ipv4_confirm) from [<c06e7a60>] (nf_iterate+0x48/0xa8)
[13257.769725] [<c06e7a60>] (nf_iterate) from [<c06e7af0>] (nf_hook_slow+0x30/0xb0)
[13257.777108] [<c06e7af0>] (nf_hook_slow) from [<c07f20b4>] (br_nf_post_routing+0x274/0x31c)
[13257.784486] [<c07f20b4>] (br_nf_post_routing) from [<c06e7a60>] (nf_iterate+0x48/0xa8)
[13257.792556] [<c06e7a60>] (nf_iterate) from [<c06e7af0>] (nf_hook_slow+0x30/0xb0)
[13257.800458] [<c06e7af0>] (nf_hook_slow) from [<c07e5580>] (br_forward_finish+0x94/0xa4)
[13257.808010] [<c07e5580>] (br_forward_finish) from [<c07f22ac>] (br_nf_forward_finish+0x150/0x1ac)
[13257.815736] [<c07f22ac>] (br_nf_forward_finish) from [<c06e8df0>] (nf_reinject+0x108/0x170)
[13257.824762] [<c06e8df0>] (nf_reinject) from [<c06ea854>] (nfqnl_recv_verdict+0x3d8/0x420)
[13257.832924] [<c06ea854>] (nfqnl_recv_verdict) from [<c06e940c>] (nfnetlink_rcv_msg+0x158/0x248)
[13257.841256] [<c06e940c>] (nfnetlink_rcv_msg) from [<c06e5564>] (netlink_rcv_skb+0x54/0xb0)
[13257.849762] [<c06e5564>] (netlink_rcv_skb) from [<c06e4ec8>] (netlink_unicast+0x148/0x23c)
[13257.858093] [<c06e4ec8>] (netlink_unicast) from [<c06e5364>] (netlink_sendmsg+0x2ec/0x368)
[13257.866348] [<c06e5364>] (netlink_sendmsg) from [<c069fb8c>] (sock_sendmsg+0x34/0x44)
[13257.874590] [<c069fb8c>] (sock_sendmsg) from [<c06a03dc>] (___sys_sendmsg+0x1ec/0x200)
[13257.882489] [<c06a03dc>] (___sys_sendmsg) from [<c06a11c8>] (__sys_sendmsg+0x3c/0x64)
[13257.890300] [<c06a11c8>] (__sys_sendmsg) from [<c0209b40>] (ret_fast_syscall+0x0/0x34)
The original code just triggered the warning but do nothing. It will
caused the shared conntrack moves to the dying list and the packet be
droppped (nf_ct_resolve_clash returns NF_DROP for dying conntrack).
- Reproduce steps:
+----------------------------+
| br0(bridge) |
| |
+-+---------+---------+------+
| eth0| | eth1| | eth2|
| | | | | |
+--+--+ +--+--+ +---+-+
| | |
| | |
+--+-+ +-+--+ +--+-+
| PC1| | PC2| | PC3|
+----+ +----+ +----+
iptables -A FORWARD -m mark --mark 0x1000000/0x1000000 -j NFQUEUE --queue-num 100 --queue-bypass
ps: Our nfq userspace program will set mark on packets whose connection
has already been processed.
PC1 sends broadcast packets simulated by hping3:
hping3 --rand-source --udp 192.168.1.255 -i u100
- Broadcast racing flow chart is as follow:
br_handle_frame
BR_HOOK(NFPROTO_BRIDGE, NF_BR_PRE_ROUTING, br_handle_frame_finish)
// skb->_nfct (unconfirmed conntrack) is constructed at PRE_ROUTING stage
br_handle_frame_finish
// check if this packet is broadcast
br_flood_forward
br_flood
list_for_each_entry_rcu(p, &br->port_list, list) // iterate through each port
maybe_deliver
deliver_clone
skb = skb_clone(skb)
__br_forward
BR_HOOK(NFPROTO_BRIDGE, NF_BR_FORWARD,...)
// queue in our nfq and received by our userspace program
// goto __nf_conntrack_confirm with process context on CPU 1
br_pass_frame_up
BR_HOOK(NFPROTO_BRIDGE, NF_BR_LOCAL_IN,...)
// goto __nf_conntrack_confirm with softirq context on CPU 0
Because conntrack confirm can happen at both INPUT and POSTROUTING
stage. So with NFQUEUE running, skb->_nfct with the same unconfirmed
conntrack could race on different core.
This patch fixes a repeating kernel splat, now it is only displayed
once.
Signed-off-by: Chieh-Min Wang <chiehminw@synology.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The reset work holds a mutex to prevent races with removal modifying the
same resources, but was unlocking only on success. Unlock on failure
too.
Fixes: 5c959d73dba64 ("nvme-pci: fix rapid add remove sequence")
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Implementation of macro "flow_action_for_each" introduced in
commit e3ab786b42535 ("flow_offload: add flow action infrastructure")
and used in commit 738678817573c ("drivers: net: use flow action
infrastructure") iterated the first item twice and did not reach the
last one. Fix it.
Fixes: e3ab786b42535 ("flow_offload: add flow action infrastructure")
Fixes: 738678817573c ("drivers: net: use flow action infrastructure")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix markup warnings for one list by using correct list syntax.
Fix markup warnings for another list by using blank lines before the
list.
Documentation/networking/device_drivers/freescale/dpaa2/dpio-driver.rst:30: WARNING: Unexpected indentation.
Documentation/networking/device_drivers/freescale/dpaa2/dpio-driver.rst:143: WARNING: Unexpected indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Cc: netdev@vger.kernel.org
Cc: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a link endpoint is re-created (e.g. after a node reboot or
interface reset), the link session number is varied by random, the peer
endpoint will be synced with this new session number before the link is
re-established.
However, there is a shortcoming in this mechanism that can lead to the
link never re-established or faced with a failure then. It happens when
the peer endpoint is ready in ESTABLISHING state, the 'peer_session' as
well as the 'in_session' flag have been set, but suddenly this link
endpoint leaves. When it comes back with a random session number, there
are two situations possible:
1/ If the random session number is larger than (or equal to) the
previous one, the peer endpoint will be updated with this new session
upon receipt of a RESET_MSG from this endpoint, and the link can be re-
established as normal. Otherwise, all the RESET_MSGs from this endpoint
will be rejected by the peer. In turn, when this link endpoint receives
one ACTIVATE_MSG from the peer, it will move to ESTABLISHED and start
to send STATE_MSGs, but again these messages will be dropped by the
peer due to wrong session.
The peer link endpoint can still become ESTABLISHED after receiving a
traffic message from this endpoint (e.g. a BCAST_PROTOCOL or
NAME_DISTRIBUTOR), but since all the STATE_MSGs are invalid, the link
will be forced down sooner or later!
Even in case the random session number is larger than the previous one,
it can be that the ACTIVATE_MSG from the peer arrives first, and this
link endpoint moves quickly to ESTABLISHED without sending out any
RESET_MSG yet. Consequently, the peer link will not be updated with the
new session number, and the same link failure scenario as above will
happen.
2/ Another situation can be that, the peer link endpoint was reset due
to any reasons in the meantime, its link state was set to RESET from
ESTABLISHING but still in session, i.e. the 'in_session' flag is not
reset...
Now, if the random session number from this endpoint is less than the
previous one, all the RESET_MSGs from this endpoint will be rejected by
the peer. In the other direction, when this link endpoint receives a
RESET_MSG from the peer, it moves to ESTABLISHING and starts to send
ACTIVATE_MSGs, but all these messages will be rejected by the peer too.
As a result, the link cannot be re-established but gets stuck with this
link endpoint in state ESTABLISHING and the peer in RESET!
Solution:
===========
This link endpoint should not go directly to ESTABLISHED when getting
ACTIVATE_MSG from the peer which may belong to the old session if the
link was re-created. To ensure the session to be correct before the
link is re-established, the peer endpoint in ESTABLISHING state will
send back the last session number in ACTIVATE_MSG for a verification at
this endpoint. Then, if needed, a new and more appropriate session
number will be regenerated to force a re-synch first.
In addition, when a link in ESTABLISHING state is reset, its state will
move to RESET according to the link FSM, along with resetting the
'in_session' flag (and the other data) as a normal link reset, it will
also be deleted if requested.
The solution is backward compatible.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski says:
====================
devlink: minor tweaks to reported device info
This series contains two minor touch ups for devlink code. First
|| is corrected to && in the ethtool compat code. Next patch
decreases the stack allocation size.
On the nfp side after further discussions with the manufacturing
team we decided to realign the serial number contents slightly and
rename one of the other fields from "vendor" to "mfr", short for
"manufacture".
v2: - add patch 3 - move board maker as a generic attribute.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The manufacturing team requests we include vendor and product
in the serial number field, as the serial number itself is not
unique across manufacturing facilities and products.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vendor may sound ambiguous, let's rename the fab string to
"board.manufacture" (which was just added as a generic identifier).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At Jiri's suggestion add a generic "board.manufacture"
version identifier.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Number of devlink attributes has grown over 128, causing the
following warning:
../net/core/devlink.c: In function ‘devlink_nl_cmd_region_read_dumpit’:
../net/core/devlink.c:3740:1: warning: the frame size of 1064 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
^
Since the number of attributes is only going to grow allocate
the array dynamically.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need the port to be both ethernet and have the rigth netdev,
not one or the other.
Fixes: ddb6e99e2db1 ("ethtool: add compat for devlink info")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Follow those steps:
# ip addr add 2001:123::1/32 dev eth0
# ip addr add 2001:123:456::2/64 dev eth0
# ip addr del 2001:123::1/32 dev eth0
# ip addr del 2001:123:456::2/64 dev eth0
and then prefix route of 2001:123::1/32 will still exist.
This is because ipv6_prefix_equal in check_cleanup_prefix_route
func does not check whether two IPv6 addresses have the same
prefix length. If the prefix of one address starts with another
shorter address prefix, even though their prefix lengths are
different, the return value of ipv6_prefix_equal is true.
Here I add a check of whether two addresses have the same prefix
to decide whether their prefixes are equal.
Fixes: 5b84efecb7d9 ("ipv6 addrconf: don't cleanup prefix route for IFA_F_NOPREFIXROUTE")
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reported-by: Wenhao Zhang <zhangwenhao8@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiong Wang says:
====================
This set improves bpf object file related rules in selftests Makefile.
- tell git to ignore the build dir "alu32".
- extend sub-register mode compilation to all bpf object files to give
LLVM compiler bpf back-end more exercise.
- auto-generate bpf kernel object file list.
- relax sub-register mode compilation criteria.
v1 -> v2:
- rename "kern_progs" to "progs". (Alexei)
- spin a new patch to remove build server kernel requirement for
sub-register mode compilation (Alexei)
- rebase on top of KaFai’s latest "test_sock_fields" patch set.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Sub-register mode compilation was enabled only when there are eBPF "v3"
processor supports at both compilation time inside LLVM and runtime inside
kernel.
Given separation betwen build and test server could be often, this patch
removes the runtime support criteria.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
At the moment, all kernel bpf objects are listed under BPF_OBJ_FILES.
Listing them manually sometimes causing patch conflict when people are
adding new testcases simultaneously.
It is better to centre all the related source files under a subdir
"progs", then auto-generate the object file list.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
At the moment, we only do extra sub-register mode compilation on bpf object
files used by "test_progs". These object files are really loaded and
executed.
This patch further extends sub-register mode compilation to all bpf object
files, even those without corresponding runtime tests. Because this could
help testing LLVM sub-register code-gen, kernel bpf selftest has much more
C testcases with reasonable size and complexity compared with LLVM
testsuite which only contains unit tests.
There were some file duplication inside BPF_OBJ_FILES_DUAL_COMPILE which
is removed now.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
"alu32" is a build dir and contains various files for BPF sub-register
code-gen testing.
This patch tells git to ignore it.
Suggested-by: Yonghong Song <yhs@fb.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
When requeue, if RQF_DONTPREP, rq has contained some driver
specific data, so insert it to hctx dispatch list to avoid any
merge. Take scsi as example, here is the trace event log (no
io scheduler, because RQF_STARTED would prevent merging),
kworker/0:1H-339 [000] ...1 2037.209289: block_rq_insert: 8,0 R 4096 () 32768 + 8 [kworker/0:1H]
scsi_inert_test-1987 [000] .... 2037.220465: block_bio_queue: 8,0 R 32776 + 8 [scsi_inert_test]
scsi_inert_test-1987 [000] ...2 2037.220466: block_bio_backmerge: 8,0 R 32776 + 8 [scsi_inert_test]
kworker/0:1H-339 [000] .... 2047.220913: block_rq_issue: 8,0 R 8192 () 32768 + 16 [kworker/0:1H]
scsi_inert_test-1996 [000] ..s1 2047.221007: block_rq_complete: 8,0 R () 32768 + 8 [0]
scsi_inert_test-1996 [000] .Ns1 2047.221045: block_rq_requeue: 8,0 R () 32776 + 8 [0]
kworker/0:1H-339 [000] ...1 2047.221054: block_rq_insert: 8,0 R 4096 () 32776 + 8 [kworker/0:1H]
kworker/0:1H-339 [000] ...1 2047.221056: block_rq_issue: 8,0 R 4096 () 32776 + 8 [kworker/0:1H]
scsi_inert_test-1986 [000] ..s1 2047.221119: block_rq_complete: 8,0 R () 32776 + 8 [0]
(32768 + 8) was requeued by scsi_queue_insert and had RQF_DONTPREP.
Then it was merged with (32776 + 8) and issued. Due to RQF_DONTPREP,
the sdb only contained the part of (32768 + 8), then only that part
was completed. The lucky thing was that scsi_io_completion detected
it and requeued the remaining part. So we didn't get corrupted data.
However, the requeue of (32776 + 8) is not expected.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When we free skb at tipc_data_input, we return a 'false' boolean.
Then, skb passed to subcalling tipc_link_input in tipc_link_rcv,
<snip>
1303 int tipc_link_rcv:
...
1354 if (!tipc_data_input(l, skb, l->inputq))
1355 rc |= tipc_link_input(l, skb, l->inputq);
</snip>
Fix it by simple changing to a 'true' boolean when skb is being free-ed.
Then, tipc_link_rcv will bypassed to subcalling tipc_link_input as above
condition.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <maloy@donjonn.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
size = sizeof(struct foo) + count * sizeof(void *);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
instance = alloc(size, GFP_KERNEL)
Notice that, in this case, variable sz is not necessary, hence it is
removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
A statement in an if block is not indented correctly. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
If a non zero value happens to be in xt[NFPROTO_BRIDGE].cur at init
time, the following panic can be caused by running
% ebtables -t broute -F BROUTING
from a 32-bit user level on a 64-bit kernel. This patch replaces
kmalloc_array with kcalloc when allocating xt.
[ 474.680846] BUG: unable to handle kernel paging request at 0000000009600920
[ 474.687869] PGD 2037006067 P4D 2037006067 PUD 2038938067 PMD 0
[ 474.693838] Oops: 0000 [#1] SMP
[ 474.697055] CPU: 9 PID: 4662 Comm: ebtables Kdump: loaded Not tainted 4.19.17-11302235.AroraKernelnext.fc18.x86_64 #1
[ 474.707721] Hardware name: Supermicro X9DRT/X9DRT, BIOS 3.0 06/28/2013
[ 474.714313] RIP: 0010:xt_compat_calc_jump+0x2f/0x63 [x_tables]
[ 474.720201] Code: 40 0f b6 ff 55 31 c0 48 6b ff 70 48 03 3d dc 45 00 00 48 89 e5 8b 4f 6c 4c 8b 47 60 ff c9 39 c8 7f 2f 8d 14 08 d1 fa 48 63 fa <41> 39 34 f8 4c 8d 0c fd 00 00 00 00 73 05 8d 42 01 eb e1 76 05 8d
[ 474.739023] RSP: 0018:ffffc9000943fc58 EFLAGS: 00010207
[ 474.744296] RAX: 0000000000000000 RBX: ffffc90006465000 RCX: 0000000002580249
[ 474.751485] RDX: 00000000012c0124 RSI: fffffffff7be17e9 RDI: 00000000012c0124
[ 474.758670] RBP: ffffc9000943fc58 R08: 0000000000000000 R09: ffffffff8117cf8f
[ 474.765855] R10: ffffc90006477000 R11: 0000000000000000 R12: 0000000000000001
[ 474.773048] R13: 0000000000000000 R14: ffffc9000943fcb8 R15: ffffc9000943fcb8
[ 474.780234] FS: 0000000000000000(0000) GS:ffff88a03f840000(0063) knlGS:00000000f7ac7700
[ 474.788612] CS: 0010 DS: 002b ES: 002b CR0: 0000000080050033
[ 474.794632] CR2: 0000000009600920 CR3: 0000002037422006 CR4: 00000000000606e0
[ 474.802052] Call Trace:
[ 474.804789] compat_do_replace+0x1fb/0x2a3 [ebtables]
[ 474.810105] compat_do_ebt_set_ctl+0x69/0xe6 [ebtables]
[ 474.815605] ? try_module_get+0x37/0x42
[ 474.819716] compat_nf_setsockopt+0x4f/0x6d
[ 474.824172] compat_ip_setsockopt+0x7e/0x8c
[ 474.828641] compat_raw_setsockopt+0x16/0x3a
[ 474.833220] compat_sock_common_setsockopt+0x1d/0x24
[ 474.838458] __compat_sys_setsockopt+0x17e/0x1b1
[ 474.843343] ? __check_object_size+0x76/0x19a
[ 474.847960] __ia32_compat_sys_socketcall+0x1cb/0x25b
[ 474.853276] do_fast_syscall_32+0xaf/0xf6
[ 474.857548] entry_SYSENTER_compat+0x6b/0x7a
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
At least BBL relies on the flat binaries containing all the bytes in the
actual image to exist in the file. Before this revert the flat images
dropped the trailing zeros, which caused BBL to put its copy of the
device tree where Linux thought the BSS was, which wreaks all sorts of
havoc. Manifesting the bug is a bit subtle because BBL aligns
everything to 2MiB page boundaries, but with large enough kernels you're
almost certain to get bitten by the bug.
While moving the sections around isn't a great long-term fix, it will at
least avoid producing broken images.
This reverts commit 22e6a2e14cb8ebcae059488cf24e778e4058c2bf.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Previously, invalid PTEs and swap PTEs had the same binary
representation, causing errors when attempting to unmap PROT_NONE
mappings, including implicit unmap on exit.
Typical error:
swap_info_get: Bad swap file entry 40000000007a9879
BUG: Bad page map in process a.out pte:3d4c3cc0 pmd:3e521401
Cc: stable@vger.kernel.org
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
mlx5_eq_cq_get() is called in IRQ handler, the spinlock inside
gets a lot of contentions when we test some heavy workload
with 60 RX queues and 80 CPU's, and it is clearly shown in the
flame graph.
In fact, radix_tree_lookup() is perfectly fine with RCU read lock,
we don't have to take a spinlock on this hot path. This is pretty
much similar to commit 291c566a2891
("net/mlx4_core: Fix racy CQ (Completion Queue) free"). Slow paths
are still serialized with the spinlock, and with synchronize_irq()
it should be safe to just move the fast path to RCU read lock.
This patch itself reduces the latency by about 50% for our memcached
workload on a 4.14 kernel we test. In upstream, as pointed out by Saeed,
this spinlock gets some rework in commit 02d92f790364
("net/mlx5: CQ Database per EQ"), so the difference could be smaller.
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal SoC management fixes from Eduardo Valentin:
"Minor fixes on of-thermal and cpu cooling"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: cpu_cooling: Clarify error message
thermal: of-thermal: Print name of device node with error
|
|
Add WARN_ON to make sure that all sub objects of a devlink device are
cleanedup before freeing the devlink device.
This helps to catch any driver bugs.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to quadratic behavior of x25_new_lci(), syzbot was able
to trigger an rcu stall.
Fix this by not blocking BH for the whole duration of
the function, and inserting a reschedule point when possible.
If we care enough, using a bitmap could get rid of the quadratic
behavior.
syzbot report :
rcu: INFO: rcu_preempt self-detected stall on CPU
rcu: 0-...!: (10500 ticks this GP) idle=4fa/1/0x4000000000000002 softirq=283376/283376 fqs=0
rcu: (t=10501 jiffies g=383105 q=136)
rcu: rcu_preempt kthread starved for 10502 jiffies! g383105 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=0
rcu: RCU grace-period kthread stack dump:
rcu_preempt I28928 10 2 0x80000000
Call Trace:
context_switch kernel/sched/core.c:2844 [inline]
__schedule+0x817/0x1cc0 kernel/sched/core.c:3485
schedule+0x92/0x180 kernel/sched/core.c:3529
schedule_timeout+0x4db/0xfd0 kernel/time/timer.c:1803
rcu_gp_fqs_loop kernel/rcu/tree.c:1948 [inline]
rcu_gp_kthread+0x956/0x17a0 kernel/rcu/tree.c:2105
kthread+0x357/0x430 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
NMI backtrace for cpu 0
CPU: 0 PID: 8759 Comm: syz-executor2 Not tainted 5.0.0-rc4+ #51
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
nmi_cpu_backtrace.cold+0x63/0xa4 lib/nmi_backtrace.c:101
nmi_trigger_cpumask_backtrace+0x1be/0x236 lib/nmi_backtrace.c:62
arch_trigger_cpumask_backtrace+0x14/0x20 arch/x86/kernel/apic/hw_nmi.c:38
trigger_single_cpu_backtrace include/linux/nmi.h:164 [inline]
rcu_dump_cpu_stacks+0x183/0x1cf kernel/rcu/tree.c:1211
print_cpu_stall kernel/rcu/tree.c:1348 [inline]
check_cpu_stall kernel/rcu/tree.c:1422 [inline]
rcu_pending kernel/rcu/tree.c:3018 [inline]
rcu_check_callbacks.cold+0x500/0xa4a kernel/rcu/tree.c:2521
update_process_times+0x32/0x80 kernel/time/timer.c:1635
tick_sched_handle+0xa2/0x190 kernel/time/tick-sched.c:161
tick_sched_timer+0x47/0x130 kernel/time/tick-sched.c:1271
__run_hrtimer kernel/time/hrtimer.c:1389 [inline]
__hrtimer_run_queues+0x33e/0xde0 kernel/time/hrtimer.c:1451
hrtimer_interrupt+0x314/0x770 kernel/time/hrtimer.c:1509
local_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1035 [inline]
smp_apic_timer_interrupt+0x120/0x570 arch/x86/kernel/apic/apic.c:1060
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:807
</IRQ>
RIP: 0010:__read_once_size include/linux/compiler.h:193 [inline]
RIP: 0010:queued_write_lock_slowpath+0x13e/0x290 kernel/locking/qrwlock.c:86
Code: 00 00 fc ff df 4c 8d 2c 01 41 83 c7 03 41 0f b6 45 00 41 38 c7 7c 08 84 c0 0f 85 0c 01 00 00 8b 03 3d 00 01 00 00 74 1a f3 90 <41> 0f b6 55 00 41 38 d7 7c eb 84 d2 74 e7 48 89 df e8 6c 0f 4f 00
RSP: 0018:ffff88805f117bd8 EFLAGS: 00000206 ORIG_RAX: ffffffffffffff13
RAX: 0000000000000300 RBX: ffffffff89413ba0 RCX: 1ffffffff1282774
RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff89413ba0
RBP: ffff88805f117c70 R08: 1ffffffff1282774 R09: fffffbfff1282775
R10: fffffbfff1282774 R11: ffffffff89413ba3 R12: 00000000000000ff
R13: fffffbfff1282774 R14: 1ffff1100be22f7d R15: 0000000000000003
queued_write_lock include/asm-generic/qrwlock.h:104 [inline]
do_raw_write_lock+0x1d6/0x290 kernel/locking/spinlock_debug.c:203
__raw_write_lock_bh include/linux/rwlock_api_smp.h:204 [inline]
_raw_write_lock_bh+0x3b/0x50 kernel/locking/spinlock.c:312
x25_insert_socket+0x21/0xe0 net/x25/af_x25.c:267
x25_bind+0x273/0x340 net/x25/af_x25.c:705
__sys_bind+0x23f/0x290 net/socket.c:1505
__do_sys_bind net/socket.c:1516 [inline]
__se_sys_bind net/socket.c:1514 [inline]
__x64_sys_bind+0x73/0xb0 net/socket.c:1514
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457e39
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fafccd0dc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000031
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457e39
RDX: 0000000000000012 RSI: 0000000020000240 RDI: 0000000000000004
RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fafccd0e6d4
R13: 00000000004bdf8b R14: 00000000004ce4b8 R15: 00000000ffffffff
Sending NMI from CPU 0 to CPUs 1:
NMI backtrace for cpu 1
CPU: 1 PID: 8752 Comm: syz-executor4 Not tainted 5.0.0-rc4+ #51
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__x25_find_socket+0x78/0x120 net/x25/af_x25.c:328
Code: 89 f8 48 c1 e8 03 80 3c 18 00 0f 85 a6 00 00 00 4d 8b 64 24 68 4d 85 e4 74 7f e8 03 97 3d fb 49 83 ec 68 74 74 e8 f8 96 3d fb <49> 8d bc 24 88 04 00 00 48 89 f8 48 c1 e8 03 0f b6 04 18 84 c0 74
RSP: 0018:ffff8880639efc58 EFLAGS: 00000246
RAX: 0000000000040000 RBX: dffffc0000000000 RCX: ffffc9000e677000
RDX: 0000000000040000 RSI: ffffffff863244b8 RDI: ffff88806a764628
RBP: ffff8880639efc80 R08: ffff8880a80d05c0 R09: fffffbfff1282775
R10: fffffbfff1282774 R11: ffffffff89413ba3 R12: ffff88806a7645c0
R13: 0000000000000001 R14: ffff88809f29ac00 R15: 0000000000000000
FS: 00007fe8d0c58700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b32823000 CR3: 00000000672eb000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
x25_new_lci net/x25/af_x25.c:357 [inline]
x25_connect+0x374/0xdf0 net/x25/af_x25.c:786
__sys_connect+0x266/0x330 net/socket.c:1686
__do_sys_connect net/socket.c:1697 [inline]
__se_sys_connect net/socket.c:1694 [inline]
__x64_sys_connect+0x73/0xb0 net/socket.c:1694
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457e39
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fe8d0c57c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457e39
RDX: 0000000000000012 RSI: 0000000020000200 RDI: 0000000000000004
RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fe8d0c586d4
R13: 00000000004be378 R14: 00000000004ceb00 R15: 00000000ffffffff
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: linux-x25@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 9178412ddf5a ("tracing: probeevent: Return consumed
bytes of dynamic area") improved the string fetching
mechanism by returning the number of required bytes after
copying the argument to the dynamic area. However, this
return value is now only used to increment the pointer
inside the dynamic area but misses updating the 'maxlen'
variable which indicates the remaining space in the dynamic
area.
This means that fetch_store_string() always reads the *total*
size of the dynamic area from the data_loc pointer instead of
the *remaining* size (and passes it along to
strncpy_from_{user,unsafe}) even if we're already about to
copy data into the middle of the dynamic area.
Link: http://lkml.kernel.org/r/20190206190013.16405-1-andreas.ziegler@fau.de
Cc: Ingo Molnar <mingo@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 9178412ddf5a ("tracing: probeevent: Return consumed bytes of dynamic area")
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
The flag offload_fwd_mark is set as the switch can forward frames by
itself.
This can be considered a fix to a problem introduced in commit
c2e866911e254067 where the port membership are not set in sync. The flag
offload_fwd_mark just needs to be set in tag_ksz.c to prevent the software
bridge from forwarding duplicate multicast frames.
Fixes: c2e866911e254067 ("microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_rx() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Otherwise we risk use-after-free and/or crashes.
Note this patch also fixes a small issue that came
with commit ce6502a8f957 ("vxlan: fix a use after free
in vxlan_encap_bypass"), since the dev->stats.rx_dropped
change was done on the wrong device.
Fixes: d342894c5d2f ("vxlan: virtual extensible lan")
Fixes: ce6502a8f957 ("vxlan: fix a use after free in vxlan_encap_bypass")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petr Machata <petrm@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Netlink has moved from bitmasks to group numbers long ago.
Signed-off-by: Jouke Witteveen <j.witteveen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Out-of-bound access to packet data from the snmp nat helper,
from Jann Horn.
2) ICMP(v6) error packets are set as related traffic by conntrack,
update protocol number before calling nf_nat_ipv4_manip_pkt()
to use ICMP(v6) rather than the original protocol number,
from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
