| Age | Commit message (Collapse) | Author |
|---|
|
drop profiles
dev_consume_skb_irq() should be called in epic_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_consume_skb_irq() should be called in dscc4_tx_irq() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drop profiles
dev_consume_skb_irq() should be called in de_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_consume_skb_irq() should be called in dfx_xmt_done() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Reviewed-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current driver only enables Pdelay_Req and Pdelay_Resp when
HWTSTAMP_FILTER_PTP_V2_EVENT, HWTSTAMP_FILTER_PTP_V1_L4_EVENT or
HWTSTAMP_FILTER_PTP_V2_L4_EVENT is requested. This results in ptp sync on
slave mode to report 'received SYNC without timestamp' when using ptp4l.
Although the hardware can support Sync, Pdelay_Req and Pdelay_resp by
setting bit14 annd bits 17/16 to 01 this leaves Delay_Req timestamps out.
Fix this by enabling all event and general messages timestamps.
This includes SYNC, Follow_Up, Delay_Req, Delay_Resp, Pdelay_Req,
Pdelay_Resp and Pdelay_Resp_Follow_Up messages.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On one hand, the mv88e6xxx driver has a work queue called in loop
which will attempt register accesses after MDIO bus suspension, that
entirely freezes the platform during suspend.
On the other hand, the DSA core is not ready yet to support suspend to
RAM operation because so far there is no way to recover reliably the
switch configuration.
To avoid the kernel to freeze when suspending with a switch driven by
the mv88e6xxx driver, we choose to prevent the driver suspension and
in the same way, the whole platform.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some case, we may use multiple pedit actions to modify packets.
The command shown as below: the last pedit action is effective.
$ tc filter add dev netdev_rep parent ffff: protocol ip prio 1 \
flower skip_sw ip_proto icmp dst_ip 3.3.3.3 \
action pedit ex munge ip dst set 192.168.1.100 pipe \
action pedit ex munge eth src set 00:00:00:00:00:01 pipe \
action pedit ex munge eth dst set 00:00:00:00:00:02 pipe \
action csum ip pipe \
action tunnel_key set src_ip 1.1.1.100 dst_ip 1.1.1.200 dst_port 4789 id 100 \
action mirred egress redirect dev vxlan0
To fix it, we add max_mod_hdr_actions to mlx5e_tc_flow_parse_attr struction,
max_mod_hdr_actions will store the max pedit action number we support and
num_mod_hdr_actions indicates how many pedit action we used, and store all
pedit action to mod_hdr_actions.
Fixes: d79b6df6b10a ("net/mlx5e: Add parsing of TC pedit actions to HW format")
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we offload tc filters to hardware, hardware flows can
be updated when mac of encap destination ip is changed.
But we ignore one case, that the mac of local encap ip can
be changed too, so we should also update them.
To fix it, add route_dev in mlx5e_encap_entry struct to save
the local encap netdevice, and when mac changed, kernel will
flush all the neighbour on the netdevice and send NETEVENT_NEIGH_UPDATE
event. The mlx5 driver will delete the flows and add them when neighbour
available again.
Fixes: 232c001398ae ("net/mlx5e: Add support to neighbour update flow")
Cc: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux
Santosh Shilimkar says:
====================
rds: add tos support
RDS applications make use of tos to classify database traffic.
This feature has been used in shipping products from 2.6.32 based
kernels. Its tied with RDS v4.1 protocol version and the compatibility
gets negotiated as part of connections setup.
Patchset keeps full backward compatibility using existing connection
negotiation scheme. Currently the feature is exploited by RDMA
transport and for TCP transport the user tos values are mapped to
same default class (0).
For RDMA transports, RDMA CM service type API is used to
set up different SL(service lanes) and the IB fabric is configured
for tos mapping using Subnet Manager(SL to VL mappings).
Similarly for ROCE fabric, user priority is mapped with different
DSCP code points which are associated with different switch queues
in the fabric.
The original code was developed by Bang Nguyen in downstream kernel back in
2.6.32 kernel days and it has evolved significantly over period of time.
Thanks to Yanjun for doing testing with various combinations of host like
v3.1<->v4.1, v4.1.<->v3.1, v4.1 upstream to shipping v4.1 etc etc
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-02-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a riscv64 JIT for BPF, from Björn.
2) Implement BTF deduplication algorithm for libbpf which takes BTF type
information containing duplicate per-compilation unit information and
reduces it to an equivalent set of BTF types with no duplication and
without loss of information, from Andrii.
3) Offloaded and native BPF XDP programs can coexist today, enable also
offloaded and generic ones as well, from Jakub.
4) Expose various BTF related helper functions in libbpf as API which
are in particular helpful for JITed programs, from Yonghong.
5) Fix the recently added JMP32 code emission in s390x JIT, from Heiko.
6) Fix BPF kselftests' tcp_{server,client}.py to be able to run inside
a network namespace, also add a fix for libbpf to get libbpf_print()
working, from Stanislav.
7) Fixes for bpftool documentation, from Prashant.
8) Type cleanup in BPF kselftests' test_maps.c to silence a gcc8 warning,
from Breno.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Manish Chopra says:
====================
qed*: Bug fixes.
This series contains general qed/qede fixes.
Please consider applying this to "net"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Version update for qed/qede modules.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix unnecessary logging of message in an expected
default case where coalescing value read (via ethtool -c)
migh not be valid unless they are configured explicitly
in the hardware using ethtool -C.
Signed-off-by: Rahul Verma <rverma@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under heavy traffic load, when changing number of channels via
ethtool (ethtool -L) which will cause interface to be reloaded,
it was observed that some packets gets transmitted on old TX
channel/queue id which doesn't really exist after the channel
configuration leads to system crash.
Add a safeguard in the driver by validating queue id through
ndo_select_queue() which is called before the ndo_start_xmit().
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Max supported queues is derived incorrectly in the case of multi-CoS.
Need to consider TCs while calculating num_queues for PF.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case of Unified Fabric Port (UFP) mode, switch provides
the traffic class (TC) value to be used for the traffic.
Configure hardware to use this TC value for vlan priority.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When slowpath messages are sent with high rate, the resulting
events can lead to a FW assert in case they are not handled fast
enough (Event Queue Full assert). Attempt to send queued slowpath
messages only after the newly evacuated entries in the EQ ring
are indicated to FW.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://people.freedesktop.org/~thomash/linux into drm-fixes
A patch set from Christoph for vmwgfx dma mode detection breakage with the
new dma code restructuring in 5.0
A couple of fixes also CC'd stable
Finally an improved IOMMU detection that automatically enables dma mapping
also with other vIOMMUS than the intel one if present and enabled.
Currently trying to start a VM in that case would fail catastrophically.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190206194735.4663-1-thellstrom@vmware.com
|
|
into drm-fixes
- Fix missing freesync properties on eDP
- Fix locking in pasid mgr
- Fix clang warning in kfd
- DC/powerplay fix
- Fix reported rev ids on raven
- Doorbell fix for vega20
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190205231301.3815-1-alexander.deucher@amd.com
|
|
There are at least four different parts with the same Vendor and Device
ID ([16c3:abcd]):
1) Synopsys HAPS USB3 controller
2) Synopsys PCIe Root Port in Freescale/NXP i.MX6Q (reported by Lucas)
3) Synopsys PCIe Root Port in Freescale/NXP i.MX6QP (reported by Lukas)
4) Synopsys PCIe Root Port in Freescale/NXP i.MX7D (reported by Trent)
The HAPS USB3 controller has a Class Code of PCI_CLASS_SERIAL_USB_XHCI,
which means the XHCI driver would normally claim it. Previously,
quirk_synopsys_haps() changed the Class Code of all [16c3:abcd] devices,
including the Root Ports, to PCI_CLASS_SERIAL_USB_DEVICE to prevent the
XHCI driver from claiming them so dwc3-haps can claim them instead.
Changing the Class Code of the Root Ports prevents the PCI core from
handling them as bridges, so devices below them don't work.
Restrict the quirk so it only changes the Class Code for devices that start
with the PCI_CLASS_SERIAL_USB_XHCI Class Code, leaving the Root Ports
alone.
Fixes: 03e6742584af ("PCI: Override Synopsys USB 3.x HAPS device class")
Reported-by: Lukas F. Hartmann <lukas@mntmn.com>
Reported-by: Trent Piepho <tpiepho@impinj.com>
Reported-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
bio_trim() has an early return, which makes it _not_ idempotent, if the
offset is 0 and the bio's bi_size already matches the requested size.
Prior to DM, all users of bio_trim() were fine with this. But DM has
exposed the fact that bio_trim()'s early return is incompatible with a
cloned bio whose integrity payload must be trimmed via
bio_integrity_trim().
Fix this by reverting DM back to doing the equivalent of bio_trim() but
in an idempotent manner (so bio_integrity_trim is always performed).
Follow-on work is needed to assess what benefit bio_trim()'s early
return is providing to its existing callers.
Reported-by: Milan Broz <gmazyland@gmail.com>
Fixes: 57c36519e4b94 ("dm: fix clone_bio() to trigger blk_recount_segments()")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Block core changes to switch bio-based IO accounting to be percpu had a
side-effect of altering DM core to now rely on calling waitqueue_active
(in both bio-based and request-based) to check if another task is in
dm_wait_for_completion().
A memory barrier is needed before calling waitqueue_active(). DM core
doesn't piggyback on a preceding memory barrier so it must explicitly
use its own.
For more details on why using waitqueue_active() without a preceding
barrier is unsafe, please see the comment before the waitqueue_active()
definition in include/linux/wait.h.
Add the missing memory barrier by switching to using wq_has_sleeper().
Fixes: 6f75723190d8 ("dm: remove the pending IO accounting")
Fixes: c4576aed8d85 ("dm: fix request-based dm's use of dm_wait_for_completion")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Ido Schimmel says:
====================
mlxsw: Offload blackhole routes
Blackhole routes are routes that cause matching packets to be silently
dropped. This is in contrast to unreachable routes that generate an ICMP
host unreachable packet in response.
The driver currently programs both route types with a trap action and
lets the kernel drop matching packets. This is sub-optimal as packets
routed using a blackhole route can be directly dropped by the ASIC.
Patch #1 alters mlxsw to program blackhole routes with a discard action.
Patch #2 adds a matching test.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a simple topology consisting of two hosts directly connected to a
router. Make sure IPv4/IPv6 ping works and then add blackhole routes.
Test that ping fails and that the routes are marked as offloaded. Use a
simple tc filter to test that packets were dropped by the ASIC and not
trapped to the CPU.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a new FIB entry type for blackhole routes and set it in case the
type of the notified route is 'RTN_BLACKHOLE'.
Program such routes with a discard action and mark them as offloaded
since the device is dropping the packets instead of the kernel.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Fainelli says:
====================
net: Introduce ndo_get_port_parent_id()
Based on discussion with Ido and feedback from Jakub there are clearly
two classes of users that implement SWITCHDEV_ATTR_ID_PORT_PARENT_ID:
- PF/VF drivers which typically only implement return the port's parent
ID, yet have to implement switchdev_port_attr_get() just for that
- Ethernet switch drivers: mlxsw, ocelot, DSA, etc. which implement more
attributes which we want to be able to eventually veto in the context
of the caller, thus making them candidates for using a blocking notifier
chain
Changes in v4:
- remove superfluous net/switchdev.h inclusions in a few files
- added Jiri's Acked-by where given
- removed err = -EOPNOTSUPP initializations
- changed according to Jiri's suggestion in net/ipv4/ipmr.c
Changes in v3:
- keep ethsw's switchdev_ops assignment
- remove inclusion of net/switchdev.h in netdevsim which is no longer
necesary
Changes in v2:
- resolved build failures spotted by kbuild test robot
- added helpers functions into the core network device layer:
dev_get_port_parent_id() and netdev_port_same_parent_id();
- added support for recursion to lower devices
Changes from RFC:
- introduce a ndo_get_port_parent_id() and convert all relevant drivers
to use it
- get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID
A subsequent set of patches will convert switchdev_port_attr_set() to
use a blocking notifier call, and still get rid of
switchdev_port_attr_get() altogether.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have a dedicated NDO for getting a port's parent ID, get rid
of SWITCHDEV_ATTR_ID_PORT_PARENT_ID and convert all callers to use the
NDO exclusively. This is a preliminary change to getting rid of
switchdev_ops eventually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ethsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdevsim only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlxsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFP only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().
Since NFP uses switchdev_port_same_parent_id() convert it to use
netdev_port_same_parent_id().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ocelot only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID as a valid
switchdev attribute getter, convert it to use ndo_get_port_parent_id()
and get rid of the switchdev_ops::switchdev_port_attr_get altogether.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlxsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx5e only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().
Since mlx5e makes use of switchdev_port_parent_id() convert it to use
netdev_port_same_parent_id().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Liquidio only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it
a great candidate to be converted to use the ndo_get_port_parent_id()
NDO instead of implementing switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BNXT only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get(). The conversion is
straight forward here since the PF and VF code use the same getter.
Since bnxt makes uses of switchdev_port_same_parent_id() convert it to
use netdev_port_same_parent_id().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for getting rid of switchdev_ops, create a dedicated NDO
operation for getting the port's parent identifier. There are
essentially two classes of drivers that need to implement getting the
port's parent ID which are VF/PF drivers with a built-in switch, and
pure switchdev drivers such as mlxsw, ocelot, dsa etc.
We introduce a helper function: dev_get_port_parent_id() which supports
recursion into the lower devices to obtain the first port's parent ID.
Convert the bridge, core and ipv4 multicast routing code to check for
such ndo_get_port_parent_id() and call the helper function when valid
before falling back to switchdev_port_attr_get(). This will allow us to
convert all relevant drivers in one go instead of having to implement
both switchdev_port_attr_get() and ndo_get_port_parent_id() operations,
then get rid of switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function can't succeed if dp->pl is NULL. It will Oops inside the
call to return phylink_ethtool_get_eee(dp->pl, e);
Fixes: 1be52e97ed3e ("dsa: slave: eee: Allow ports to use phylink")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change t4fw_version.h to update latest firmware version
number to 1.22.9.0.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Read MAC address 32-bit at a time and manually extract the individual
bytes. This avoids pointer aliasing and gives the compiler a better
chance of optimizing the operation.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the system was booted using a device tree and if the device tree
contains a MAC address, use it instead of reading one from the EEPROM.
This is useful in situations where the EEPROM isn't properly programmed
or where the firmware wants to override the existing MAC address.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two and a half years ago, the client was changed to use gathered
Send for larger inline messages, in commit 655fec6987b ("xprtrdma:
Use gathered Send for large inline messages"). Several fixes were
required because there are a few in-kernel device drivers whose
max_sge is 3, and these were broken by the change.
Apparently my memory is going, because some time later, I submitted
commit 25fd86eca11c ("svcrdma: Don't overrun the SGE array in
svc_rdma_send_ctxt"), and after that, commit f3c1fd0ee294 ("svcrdma:
Reduce max_send_sges"). These too incorrectly assumed in-kernel
device drivers would have more than a few Send SGEs available.
The fix for the server side is not the same. This is because the
fundamental problem on the server is that, whether or not the client
has provisioned a chunk for the RPC reply, the server must squeeze
even the most complex RPC replies into a single RDMA Send. Failing
in the send path because of Send SGE exhaustion should never be an
option.
Therefore, instead of failing when the send path runs out of SGEs,
switch to using a bounce buffer mechanism to handle RPC replies that
are too complex for the device to send directly. That allows us to
remove the max_sge check to enable drivers with small max_sge to
work again.
Reported-by: Don Dutile <ddutile@redhat.com>
Fixes: 25fd86eca11c ("svcrdma: Don't overrun the SGE array in ...")
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
If the parameter 'count' is non-zero, nfsd4_clone_file_range() will
currently clobber all errors returned by vfs_clone_file_range() and
replace them with EINVAL.
Fixes: 42ec3d4c0218 ("vfs: make remap_file_range functions take and...")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
When something let __find_get_block_slow() hit all_mapped path, it calls
printk() for 100+ times per a second. But there is no need to print same
message with such high frequency; it is just asking for stall warning, or
at least bloating log files.
[ 399.866302][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8
[ 399.873324][T15342] b_state=0x00000029, b_size=512
[ 399.878403][T15342] device loop0 blocksize: 4096
[ 399.883296][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8
[ 399.890400][T15342] b_state=0x00000029, b_size=512
[ 399.895595][T15342] device loop0 blocksize: 4096
[ 399.900556][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8
[ 399.907471][T15342] b_state=0x00000029, b_size=512
[ 399.912506][T15342] device loop0 blocksize: 4096
This patch reduces frequency to up to once per a second, in addition to
concatenating three lines into one.
[ 399.866302][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8, b_state=0x00000029, b_size=512, device loop0 blocksize: 4096
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add maintainer entry for SFF/SFP/SFP+ support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When calling register_blkdev() with specified major
device number, the return code is 0 on success.
So it seems not correct direct assign return code to
variable major_num in this case.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We've received a bugreport that using LPM with a SAMSUNG
MZ7TE512HMHP-000L1 SSD leads to system instability, we already have
a quirk for the MZ7TD256HAFV-000L9, which is also a Samsun EVO 840 /
PM851 OEM model, so it seems some of these models have a LPM issue.
This commits adds a NOLPM quirk for the model string from the new
bugeport, to avoid the reported stability issues.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1571330
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Ido Schimmel says:
====================
mlxsw: core: Trace EMAD errors
Nir says:
This patchset adds a trace for EMAD errors to the existing EMAD payload
traces. This tracepoint is useful to track user or firmware errors during
tests execution.
Patch #1 defines the devlink tracepoint.
Patch #2 uses it for reporting mlxsw EMAD errors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
