| Age | Commit message (Collapse) | Author |
|---|
|
PORT RECOVERY TIMEOUT is the maximum time between the controller's
detection of the PHY down until the receipt of the ID_Frame (from the
same remote SAS port). If the time expires before the ID_FRAME is
received, the port is considered INVALID and can be removed. The
IOP_EVENT_PORT_RECOVERY_TIMER_TMO event is reported following the
IOP_EVENT_ PHY_DOWN event when the PHY/port does not recover after
Port Recovery Time.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
If the link error happens, we don't need to disconnect the phy,
which will remove the drive. Instead acknowledging the controller
and logging the error will be enough.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
In pm8001_ccb_task_free(), the dma unmapping is done based on
ccb->n_elem value. This should be initialized to zero in the
task_abort(). Otherwise, pm8001_ccb_task_free() will try for
dma_unmap_sg() which is invalid for task abort and can lead to
kernel crash.
Changes From V1:
None
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Thermal page code has been changed to 7 for the 12G controllers.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
In Nexus reset the device state request are not needed.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Updated 12G linkrate to libsas.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Company has policy to use company email address, so update
my email address to company address.
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Use logical instead of bitwise AND.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Invoking get_cmd_state for qla2xxx always returns 0. Instead change it
to return the actual fabric state from qla_tgt_cmd. This will help with
debugging.
Signed-off-by: Dilip Kumar Uppugandla <dilip@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
The driver is calling hpsa_shutdown before calling scsi_remove_host.
hpsa_shutdown is disabling interrupts.
scsi_remove_host can trigger I/O operations, such as
SYNCHRONIZE CACHE when multipath is enabled which hang the system.
Call scsi_remove_host before calling hpsa_shutdown.
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
A regression was introduced into the hpsa driver a while back so
non-zero LUNs of multi-LUN devices may no longer be presented via
a SAS based Smart Array. I have not done a bisection to discover
the change that caused it.
The CISS firmware specification (available on sourceforge)
defines an 8 byte lunid that describes devices that the Smart
Array can see/present to the system. The current code in the hpsa
driver attempts to find matches for non-zero LUNs with LUN 0 for
a bus/target by zeroing out byte 4 of the lunid and find a match.
This method is sufficient for SCSI based Smart Arrays because
byte 5 is always 0. For SAS based Smart arrays byte 5 of the
lunid contains the path number for a multipath device and
either one or two bits (the documentation does not define how
many bits are used but it appears it may be one only) that
indicate if the given path number in byte 5 must always be
used to access that device. Byte 5 may not always be zero.
The following are lunids (spaces added for clarity) for a
MSL2024 single drive library connected via a H241 Smart Array:
00 00 00 00 01 00 00 01 (changer)
00 00 00 00 00 80 00 01 (tape)
In the 4th byte (counting from 0) you can see that the tape
is LUN 0 and the changer is LUN 1. The 0x80 set in the 5th byte
for the tape drive means the driver should force access to
path 0 (the library in this case was connected to one path only
anyway).
After the changes we can see the following in the dmesg output:
scsi 0:3:0:0: RAID HP H241 1.18 \
PQ: 0 ANSI: 5
scsi 0:2:0:0: Sequential-Access HP Ultrium 6-SCSI 354W \
PQ: 0 ANSI: 6
scsi 0:2:0:1: Medium Changer HP MSL G3 Series 8.70 \
PQ: 0 ANSI: 5
Showing that the changer is correctly identified as LUN 1 of
bus 2 target 0. Before the change the changer device is not seen.
Suggested-by: shane.seymour <shane.seymour@hp.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
prevent adding volumes that are not available.
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
showing that tables have been updated unnecessarily.
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
host no, bus, target, lun, scsi_device_type
for hba mode add: box and bay information
report if the path is active/inactive
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
need to add PMC to copyright notice and update the Hewlett-Packard
copyright notification.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Nick Meier reported a regression with HyperV that "
After rebooting the VM, the following messages are logged in syslog
when trying to load the tulip driver:
tulip: Linux Tulip drivers version 1.1.15 (Feb 27, 2007)
tulip: 0000:00:0a.0: PCI INT A: failed to register GSI
tulip: Cannot enable tulip board #0, aborting
tulip: probe of 0000:00:0a.0 failed with error -16
Errors occur in 3.19.0 kernel
Works in 3.17 kernel.
"
According to the ACPI dump file posted by Nick at
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1440072
The ACPI MADT table includes an interrupt source overridden entry for
ACPI SCI:
[236h 0566 1] Subtable Type : 02 <Interrupt Source Override>
[237h 0567 1] Length : 0A
[238h 0568 1] Bus : 00
[239h 0569 1] Source : 09
[23Ah 0570 4] Interrupt : 00000009
[23Eh 0574 2] Flags (decoded below) : 000D
Polarity : 1
Trigger Mode : 3
And in DSDT table, we have _PRT method to define PCI interrupts, which
eventually goes to:
Name (PRSA, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
Name (PRSB, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
Name (PRSC, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
Name (PRSD, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
According to the MADT and DSDT tables, IRQ 9 may be used for:
1) ACPI SCI in level, high mode
2) PCI legacy IRQ in level, low mode
So there's a conflict in polarity setting for IRQ 9.
Prior to commit cd68f6bd53cf ("x86, irq, acpi: Get rid of special
handling of GSI for ACPI SCI"), ACPI SCI is handled specially and
there's no check for conflicts between ACPI SCI and PCI legagy IRQ.
And it seems that the HyperV hypervisor doesn't make use of the
polarity configuration in IOAPIC entry, so it just works.
Commit cd68f6bd53cf gets rid of the specially handling of ACPI SCI,
and then the pin attribute checking code discloses the conflicts
between ACPI SCI and PCI legacy IRQ on HyperV virtual machine,
and rejects the request to assign IRQ9 to PCI devices.
So penalize legacy IRQ used by ACPI SCI and mark it unusable if ACPI
SCI attributes conflict with PCI IRQ attributes.
Please refer to following links for more information:
https://bugzilla.kernel.org/show_bug.cgi?id=101301
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1440072
Fixes: cd68f6bd53cf ("x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI")
Reported-and-tested-by: Nick Meier <nmeier@microsoft.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: 3.19+ <stable@vger.kernel.org> # 3.19+
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Bump version and update the copyright year for i40evf.
Change-ID: Iddb81b9dba09f0dc57ab54937b5821ecdd721ff6
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Store the CEE TLV status returned by firmware to allow drivers to dump that
for debug purposes.
Change-ID: Ie3c4cf8cebabee4f15e1e3fdc4fc8a68bbca40ee
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add virtual channel offload capability to support RX polling mode in the
VF.
Change-ID: Ib643ae2a7506dfc75fc489fc207493fabefa4832
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The kernel notifies all VXLAN capable registered drivers, i.e. any
driver that implements ndo_add_vxlan_port(), of the addition of a
port so that the driver can track which ports are in use. There's
no need to log this - it just fills the system log with useless and
irksome noise.
Also, when failing to init SR-IOV interfaces the driver was printing the
same message twice. Just remove the inner printk and let the outer message
catch enable as well as the other failures.
Change-ID: Id5ecb1d425c2a357ee2bc1635dab24553831dade
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There were quite a few issues when the wrong defines were getting used
in the VF driver. This patch fixes the code where PF driver registers
were getting used for VF driver, and also removes the registers that are
not being used from the VF register file.
Change-ID: If116a9730112950d006eb8ec763998fc914cc839
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use CTLN1 instead of CTLN for the VF relative register space.
Change-ID: Iefba63faf0307af55fec8dbb64f26059f7d91318
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Turns out that 'inavlid' is an inavlid spelling for 'invalid'.
Change-ID: Ie1fe2d0f8d1ba75ab880594875ec2e4152a76f61
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The existing comment is incorrect. Add new comment to point out that the
PF reset does not affect link but if the reset is changed to a different
type that does affect link then the link test would need to be moved to
before the reset.
Change-ID: I28d786f46e9465860babdee61c1dba51016464df
Reported-by: Jeremiah Kyle <jeremiah.kyle@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds capability to update per VEB per TC statistics and dump
it via ethtool. It also adds a structure to hold VEB per TC statistics.
The fields can be filled by reading the GLVEBTC_* counters.
Change-ID: I28b4759b9ab6ad5a61f046a1bc9ef6b16fe31538
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Treat netqueues the same way we do virtual functions when someone wants to
run the ethtool offline diagnostic test.
Change-ID: Id48d2b933f1fd0db7be06305a93c6ebe3dc821f5
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes the driver flow to take into account legacy interrupts.
Over time we added code that assumes MSIX is the only mode that the
driver runs in. It also enables a legacy workaround to trigger SWINT
when the TX ring has non-cache aligned descriptors pending and interrupts
are disabled.
We work with a single vector in MSI mode too, so apply the same
restrictions as Legacy.
Change-ID: I826ddff1f9bd45d2dbe11f56a3ddcef0dbf42563
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We should be stopping the service task and flow director on
shutdown not on suspension.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The port.crc_errors is really an RX counter, so let's mark it as such.
Change-ID: I179afd3f8a95d45229bb4163a6aeb01f0d2d250b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Sparse cries when we compare an __le16 to a u16, almost like it cares
about architectures other than x86. Weird. Use the le16_to_cpu macro to
make it stop crying.
Change-ID: Id068f4d7868a2d3df234a791a76d15938f37db35
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There are trackpoint devices that fail to respond to the PS2 command
PSMOUSE_CMD_GETID if immediately queried after the parent device is
deactivated. Add a small delay for the hardware to get in a sane state
before sending any PS2 commands.
One example of such a system is:
Lenovo ThinkPad X120e, model 30515QG
synaptics: Touchpad model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd001a3/0x940300/0x121c00, board id: 1811, fw id: 797391
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Provide a software-based implementation of the priviledged no access
support found in ARMv8.1.
Userspace pages are mapped using a different domain number from the
kernel and IO mappings. If we switch the user domain to "no access"
when we enter the kernel, we can prevent the kernel from touching
userspace.
However, the kernel needs to be able to access userspace via the
various user accessor functions. With the wrapping in the previous
patch, we can temporarily enable access when the kernel needs user
access, and re-disable it afterwards.
This allows us to trap non-intended accesses to userspace, eg, caused
by an inadvertent dereference of the LIST_POISON* values, which, with
appropriate user mappings setup, can be made to succeed. This in turn
can allow use-after-free bugs to be further exploited than would
otherwise be possible.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Provide hooks into the kernel entry and exit paths to permit control
of userspace visibility to the kernel. The intended use is:
- on entry to kernel from user, uaccess_disable will be called to
disable userspace visibility
- on exit from kernel to user, uaccess_enable will be called to
enable userspace visibility
- on entry from a kernel exception, uaccess_save_and_disable will be
called to save the current userspace visibility setting, and disable
access
- on exit from a kernel exception, uaccess_restore will be called to
restore the userspace visibility as it was before the exception
occurred.
These hooks allows us to keep userspace visibility disabled for the
vast majority of the kernel, except for localised regions where we
want to explicitly access userspace.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The following structure is just asking for trouble:
#ifdef CONFIG_symbol
.macro foo
...
.endm
.macro bar
...
.endm
.macro baz
...
.endm
#else
.macro foo
...
.endm
.macro bar
...
.endm
#ifdef CONFIG_symbol2
.macro baz
...
.endm
#else
.macro baz
...
.endm
#endif
#endif
such as one defintion being updated, but the other definitions miss out.
Where the contents of a macro needs to be conditional, the hint is in
the first clause of this very sentence. "contents" "conditional". Not
multiple separate definitions, especially not when much of the macro
is the same between different configs.
This patch fixes this bad style, which had caused the Thumb2 code to
miss-out on the uaccess updates.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch introduce a new helper f2fs_update_extent_tree_range which can
do extent mapping update at a specified range.
The main idea is:
1) punch all mapping info in extent node(s) which are at a specified range;
2) try to merge new extent mapping with adjacent node, or failing that,
insert the mapping into extent tree as a new node.
In order to see the benefit, I add a function for stating time stamping
count as below:
uint64_t rdtsc(void)
{
uint32_t lo, hi;
__asm__ __volatile__ ("rdtsc" : "=a" (lo), "=d" (hi));
return (uint64_t)hi << 32 | lo;
}
My test environment is: ubuntu, intel i7-3770, 16G memory, 256g micron ssd.
truncation path: update extent cache from truncate_data_blocks_range
non-truncataion path: update extent cache from other paths
total: all update paths
a) Removing 128MB file which has one extent node mapping whole range of
file:
1. dd if=/dev/zero of=/mnt/f2fs/128M bs=1M count=128
2. sync
3. rm /mnt/f2fs/128M
Before:
total count average
truncation: 7651022 32768 233.49
Patched:
total count average
truncation: 3321 33 100.64
b) fsstress:
fsstress -d /mnt/f2fs -l 5 -n 100 -p 20
Test times: 5 times.
Before:
total count average
truncation: 5812480.6 20911.6 277.95
non-truncation: 7783845.6 13440.8 579.12
total: 13596326.2 34352.4 395.79
Patched:
total count average
truncation: 1281283.0 3041.6 421.25
non-truncation: 7355844.4 13662.8 538.38
total: 8637127.4 16704.4 517.06
1) For the updates in truncation path:
- we can see updating in batches leads total tsc and update count reducing
explicitly;
- besides, for a single batched updating, punching multiple extent nodes
in a loop, result in executing more operations, so our average tsc
increase intensively.
2) For the updates in non-truncation path:
- there is a little improvement, that is because for the scenario that we
just need to update in the head or tail of extent node, new interface
optimize to update info in extent node directly, rather than removing
original extent node for updating and then inserting that updated one
into cache as new node.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvs-next
Simon Horman says:
====================
Second Round of IPVS Updates for v4.3
I realise these are a little late in the cycle, so if you would prefer
me to repost them for v4.4 then just let me know.
The updates include:
* A new scheduler from Raducu Deaconu
* Enhanced configurability of the sync daemon from Julian Anastasov
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Current critical clock list for pistachio enables
only mips and sys clocks by default but there are
also other clocks that are not claimed by anyone and
needs to be enabled by default.
This patch updates the critical clocks that need
to be enabled by default.
Add a separate struct to distinguish the critical clocks
as listed:
1.) core clocks:
a.) mips clock
2.) peripheral system clocks:
a.) sys clock
b.) sys_bus clock
c.) DDR clock
d.) ROM clock
Fixes: b35d7c33419c("CLK: Pistachio: Register core clocks")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
.recalc_rate callback for the fractional PLL doesn't take operating
mode into account when calculating PLL rate. This results in
the incorrect PLL rates when PLL is operating in integer mode.
Operating mode of fractional PLL is based on the value of the
fractional divider. Currently it assumes that the PLL will always
be configured in fractional mode which may not be
the case. This may result in the wrong output frequency.
Also vco was calculated based on the current operating mode which
makes no sense because .set_rate is setting operating mode. Instead,
vco should be calculated using PLL settings that are about to be set.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
PLL enable callbacks are overriding PLL mode (int/frac) and
Noise reduction (on/off) settings set by the boot loader which
results in the incorrect clock rate.
PLL mode and noise reduction are defined by the DSMPD and DACPD bits
of the PLL control register. PLL .enable() callbacks enable PLL
by deasserting all power-down bits of the PLL control register,
including DSMPD and DACPD bits, which is not necessary since
these bits don't actually enable/disable PLL.
This commit fixes the problem by removing DSMPD and DACPD bits
from the "PLL enable" mask.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresitcker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This commit fixes 32bit integer overflows throughout the pll driver
(i.e. wherever the result of integer multiplication may exceed the
range of u32).
One of the functions affected by this problem is .recalc_rate. It
returns incorrect rate for some pll settings (not for all though)
which in turn results in the incorrect rate setup of pll's child
clocks.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
RFC 4443 added two new codes values for ICMPv6 type 1:
5 - Source address failed ingress/egress policy
6 - Reject route to destination
And RFC 7084 states in L-14 that IPv6 Router MUST send ICMPv6 Destination
Unreachable with code 5 for packets forwarded to it that use an address
from a prefix that has been invalidated.
Codes 5 and 6 are more informative subsets of code 1.
Signed-off-by: Andreas Herz <andi@geekosphere.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Pull block fixes from Jens Axboe:
"Two fixes in this pull request:
- The writeback regression fix from Tejun, which has been weeks in
the making. This fixes a case where we would sometimes not issue
writeback when we should have.
- An older fix for a memory corruption issue in mtip32xx. It was
deferred since we wanted a better fix for this (driver should not
have to handle that case), but given the timing, it's better to put
the simple fix in for 4.2 release"
* 'for-linus' of git://git.kernel.dk/linux-block:
mtip32x: fix regression introduced by blk-mq per-hctx flush
writeback: sync_inodes_sb() must write out I_DIRTY_TIME inodes and always call wait_sb_inodes()
|
|
Alexei Starovoitov says:
====================
act_bpf: remove spinlock in fast path
v1 version had a race condition in cleanup path of bpf_prog.
I tried to fix it by adding new callback 'cleanup_rcu' to 'struct tcf_common'
and call it out of act_api cleanup path, but Daniel noticed
(thanks for the idea!) that most of the classifiers already do action cleanup
out of rcu callback.
So instead this set of patches converts tcindex and rsvp classifiers to call
tcf_exts_destroy() after rcu grace period and since action cleanup logic
in __tcf_hash_release() is only called when bind and refcnt goes to zero,
it's guaranteed that cleanup() callback is called from rcu callback.
More specifically:
patches 1 and 2 - simple fixes
patches 2 and 3 - convert tcf_exts_destroy in tcindex and rsvp to call_rcu
patch 5 - removes spin_lock from act_bpf
The cleanup of actions is now universally done after rcu grace period
and in the future we can drop (now unnecessary) call_rcu from tcf_hash_destroy()
patch 5 is using synchronize_rcu() in act_bpf replacement path, since it's
very rare and alternative of dynamically allocating 'struct tcf_bpf_cfg' just
to pass it to call_rcu looks even less appealing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to act_gact/act_mirred, act_bpf can be lockless in packet processing
with extra care taken to free bpf programs after rcu grace period.
Replacement of existing act_bpf (very rare) is done with synchronize_rcu()
and final destruction is done from tc_action_ops->cleanup() callback that is
called from tcf_exts_destroy()->tcf_action_destroy()->__tcf_hash_release() when
bind and refcnt reach zero which is only possible when classifier is destroyed.
Previous two patches fixed the last two classifiers (tcindex and rsvp) to
call tcf_exts_destroy() from rcu callback.
Similar to gact/mirred there is a race between prog->filter and
prog->tcf_action. Meaning that the program being replaced may use
previous default action if it happened to return TC_ACT_UNSPEC.
act_mirred race betwen tcf_action and tcfm_dev is similar.
In all cases the race is harmless.
Long term we may want to improve the situation by replacing the whole
tc_action->priv as single pointer instead of updating inner fields one by one.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust destroy path of cls_rsvp to call tcf_exts_destroy() after
rcu grace period.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
