| Age | Commit message (Collapse) | Author |
|---|
|
Convert this PCI driver to use the comedi PCI auto config attach
mechanism by adding an 'attach_pci' callback function. Since the
driver does not require any external configuration options, and
the legacy 'attach' callback is now optional, remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the kernel message noise during the attach of the board.
Use a simple/clean dev_info at the end of the attach.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit cd4f2d4 (i2c: mxs: Set I2C timing registers for mxs-i2c) only
covered the case for devicetree and made platform_data based boards
bail out with -EINVAL. Correctly support the latter one, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
On transactions with n>=2 bytes, the controller actually wrongly clocks in n+1
bytes. This is caused by the (wrong) assumption that RFE in the Status Register
is 1 iff there is no byte already ordered (via a dummy TX byte). This lead to
the implementation of synchronized byte ordering, e.g.:
Dummy-TX - RX - Dummy-TX - RX - ...
But since RFE actually stays high after some Dummy-TX, it rather looks like:
Dummy-TX - Dummy-TX - RX - Dummy-TX - RX - (RX)
The last RX byte is clocked in by the bus controller, but ignored by the kernel
when filling the userspace buffer.
This patch fixes the issue by asking for RX via Dummy-TX asynchronously.
Introducing a separate counter for TX bytes.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
The I2C Control Register bits RFDAIE and RFFIE were mixed up. In addition to
this fix, this patch adds the missing bit DRSIE for completeness.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
auto75914331@hushmail.com reports that iptables does not correctly
output the KERN_<level>.
$IPTABLES -A RULE_0_in -j LOG --log-level notice --log-prefix "DENY in: "
result with linux 3.6-rc5
Sep 12 06:37:29 xxxxx kernel: <5>DENY in: IN=eth0 OUT= MAC=.......
result with linux 3.5.3 and older:
Sep 9 10:43:01 xxxxx kernel: DENY in: IN=eth0 OUT= MAC......
commit 04d2c8c83d0
("printk: convert the format for KERN_<LEVEL> to a 2 byte pattern")
updated the syslog header style but did not update netfilter uses.
Do so.
Use KERN_SOH and string concatenation instead of "%c" KERN_SOH_ASCII
as suggested by Eric Dumazet.
Signed-off-by: Joe Perches <joe@perches.com>
cc: auto75914331@hushmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The AK4396 DAC has a linear-scale attentuator, but
sound/pci/ice1712/prodigy_hifi.c used a log scale instead, which is
not quite right. This patch restores the correct scale, borrowing
from the ak4396 code in sound/pci/oxygen/oxygen.c.
Signed-off-by: Matteo Frigo <athena@fftw.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The driver uses be16_to_cpu and cpu_to_be16 to convert data in SMBus word
operations from chip to host byte order. However, the data passed from and to
the SMBus word API functions is in host byte order, not in chip byte order.
Conversion should therefore use swab16 instead of be16 to change the byte order.
Replace driver internal word conversion functions with SMBus API functions to
solve the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.5+
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
twl4030_madc_conversion uses do_avg and type structure elements of
twl4030_madc_request. Initialize structure to avoid random operation.
Fix for: Coverity CID 200794 Uninitialized scalar variable.
Cc: Keerthy <j-keerthy@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Keerthy <j-keerthy@ti.com>
|
|
Its possible to setup a bad cbq configuration leading to
an infinite loop in cbq_classify()
DEV_OUT=eth0
ICMP="match ip protocol 1 0xff"
U32="protocol ip u32"
DST="match ip dst"
tc qdisc add dev $DEV_OUT root handle 1: cbq avpkt 1000 \
bandwidth 100mbit
tc class add dev $DEV_OUT parent 1: classid 1:1 cbq \
rate 512kbit allot 1500 prio 5 bounded isolated
tc filter add dev $DEV_OUT parent 1: prio 3 $U32 \
$ICMP $DST 192.168.3.234 flowid 1:
Reported-by: Denys Fedoryschenko <denys@visp.net.lb>
Tested-by: Denys Fedoryschenko <denys@visp.net.lb>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"It's later than I'd like but well the timing just didn't work out this
time.
There are three bug fixes. One from before 3.6-rc1 and two from the
new CPU hotplug code. Kudos to Lai for discovering all of them and
providing fixes.
* Atomicity bug when clearing a flag and setting another. The two
operation should have been atomic but wasn't. This bug has existed
for a long time but is unlikely to have actually happened. Fix is
safe. Marked for -stable.
* If CPU hotplug cycles happen back-to-back before workers finish the
previous cycle, the states could get out of sync and it could get
stuck. Fixed by waiting for workers to complete before finishing
hotplug cycle.
* While CPU hotplug is in progress, idle workers could be depleted
which can then lead to deadlock. I think both happening together
is highly unlikely but still better to fix it and the fix isn't too
scary.
There's another workqueue related regression which reported a few days
ago:
https://bugzilla.kernel.org/show_bug.cgi?id=47301
It's a bit of head scratcher but there is a semi-reliable reproduce
case, so I'm hoping to resolve it soonish."
* 'for-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix possible idle worker depletion across CPU hotplug
workqueue: restore POOL_MANAGING_WORKERS
workqueue: fix possible deadlock in idle worker rebinding
workqueue: move WORKER_REBIND clearing in rebind_workers() to the end of the function
workqueue: UNBOUND -> REBIND morphing in rebind_workers() should be atomic
|
|
Pull crypto fixes from Herbert Xu:
"This fixes the authenc self-test crash as well as a missing export of
a symbol used by a module."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: authenc - Fix crash with zero-length assoc data
crypto/caam: Export gen_split_key symbol for other modules
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin
Pull blackfin updates from Bob Liu:
"One kbuild and a smp build fix."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
kbuild: add symbol prefix arg to kallsyms
blackfin: smp: adapt to generic smp helpers
|
|
Fix defines to comply with style guidelines
Signed-off-by: Daniel Cotey <puff65537@bansheeslibrary.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DEVICE_NODE not used
Signed-off-by: Daniel Cotey <puff65537@bansheeslibrary.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix msec_delay_bp macro formatting
Signed-off-by: Daniel Cotey <puff65537@bansheeslibrary.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver no longer walks the pci bus to find the pci_dev.
The pci_dev_put() is no longer needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These comments are pretty obvious. Remove them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This macro relies on a local variable having a specific name.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert this PCI driver to use the comedi PCI auto config attach
mechanism by adding an 'attach_pci' callback function. Since the
driver does not require any external configuration options, and
the legacy 'attach' callback is now optional, remove it. The
boardinfo is also not needed now so remove it also.
This also allows removing the icp_multi.h header completely.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the kernel message noise during the attach of the board.
Use a simple/clean dev_info at the end of the attach.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This board always has 5 subdevices.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The board supported by this driver always supports interrupts.
Remove the boardinfo.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This variable is not used in the driver. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This variable is not used in the driver. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The analog inputs and outputs for this driver use the same table
to set the analog range. Remove the boardinfo for it and just
reference the table directly.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is only one board type supported by this driver and the
analog input ranges are constant. Remove the boardinfo for it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This variable is not used by the driver. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The analog inputs of this board always have 12-bit resolution.
Remove the boardinfo and just open-code the value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The analog outputs of this board always have 12-bit resolution.
Remove the boardinfo and just open-code the value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The analog inputs for this board always support differential
inputs and the number of channels is half the normal analog
input number.
Remove the n_aichand field from the boardinfo and fix the code
accordingly.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is only one board type supported by this driver and the
number of analog input channels is constant. Remove the
boardinfo for it and just open-code the value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is only one board type supported by this driver and the
number of analog output channels is constant. Remove the
boardinfo for it and just open-code the value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is only one board type supported by this driver and the
number of digital input channels is constant. Remove the
boardinfo for it and just open-code the value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is only one board type supported by this driver and the
number of digital output channels is constant. Remove the
boardinfo for it and just open-code the value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is only one board type supported by this driver and the
number of counter channels is constant. Remove the boardinfo
for it and just open-code the value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This define enables a bunch of function trace messages. These
should be removed in the final driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver is for a PCI device not a legacy device.
Convert it from a module_comedi_driver to a module_comedi_pci_driver.
This will allow using the comedi_pci_auto_config mechanism to attach
to the device.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need to ensure that if the call to filemap_write_and_wait_range()
fails, then we report that error back to the application.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Fix the ZTE K5006-Z entry so that it actually matches anything
commit f1b5c997 USB: option: add ZTE K5006-Z
added a device specific entry assuming that the device would use
class/subclass/proto == ff/ff/ff like other ZTE devices. It
turns out that ZTE has started using vendor specific subclass
and protocol codes:
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=1018 Rev= 0.00
S: Manufacturer=ZTE,Incorporated
S: Product=ZTE LTE Technologies MSM
S: SerialNumber=MF821Vxxxxxxx
C:* #Ifs= 5 Cfg#= 1 Atr=c0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=86 Prot=10 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=05 Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=00 Driver=qmi_wwan
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
We do not have any information on how ZTE intend to use these
codes, but let us assume for now that the 3 sets matching
serial functions in the K5006-Z always will identify a serial
function in a ZTE device.
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This way we do no longer need to keep a dangling pointer to struct
ipack_device in tpci200_slot after the device has been removed.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As the IP module driver takes care of freeing its resources.
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is not needed as the IP module should free its IRQ using
tpci200_free_irq callback.
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
exiting
As the ipack_bus_unregister() takes care of unregistering the devices plugged
in the carrier, it is not needed to do it in the carrier driver.
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Find the IP modules that are plugged to the carrier and unregister them.
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As the IRQ was requested by the driver, it should free it also.
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ipoctal devices can be uninstalled from the ipack_driver_unregister()
call as the device model calles the bus's .remove() function for each device
registered by the driver and it will execute the .remove() function of the
ipoctal driver.
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Using the call to the ipack_device_unregister() function to avoid the
strange way it was doing, as the device model will take care of calling
the bus's .remove function when a device is being unregistered.
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As indicated in the documentation of pci_dev_get.
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move iounmap and pci_release_region to tpci200_unregister(), as it is the place
where the clean-up of the device is done.
Also, renamed iounmap() to pci_iounmap() as the mapped region was requested
from PCI bus.
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
