| Age | Commit message (Collapse) | Author |
|---|
|
The Doorbell HW block can be configured at a granularity
of 16 x CIDs, so we need to make sure that the actual number
of CIDs configured would be a multiplication of 16.
Today, when RoCE is enabled - given that the number is unaligned,
doorbelling the higher CIDs would fail to reach the firmware and
would eventually timeout.
Fixes: dbb799c39717 ("qed: Initialize hardware for new protocols")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
mlxsw: Couple of fixes
Couple or small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The num_rec field is 8 bit, so the maximal count number is 255.
This fixes vlans learning not being enabled for wider ranges than 255.
Fixes: a4feea74cd7a ("mlxsw: reg: Add Switch Port VLAN MAC Learning register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The num_rec field is 8 bit, so the maximal count number is 255. This
fixes vlans not being enabled for wider ranges than 255.
Fixes: b2e345f9a454 ("mlxsw: reg: Add Switch Port VID and Switch Port VLAN Membership registers definitions")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we notify peers of potential changes, it's also good to update
IGMP memberships. For example, during VM migration, updating IGMP
memberships will redirect existing multicast streams to the VM at the
new location.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The setup/remove_state/instance() functions in the hotplug core code are
serialized against concurrent CPU hotplug, but unfortunately not serialized
against themself.
As a consequence a concurrent invocation of these function results in
corruption of the callback machinery because two instances try to invoke
callbacks on remote cpus at the same time. This results in missing callback
invocations and initiator threads waiting forever on the completion.
The obvious solution to replace get_cpu_online() with cpu_hotplug_begin()
is not possible because at least one callsite calls into these functions
from a get_online_cpu() locked region.
Extend the protection scope of the cpuhp_state_mutex from solely protecting
the state arrays to cover the callback invocation machinery as well.
Fixes: 5b7aa87e0482 ("cpu/hotplug: Implement setup/removal interface")
Reported-and-tested-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: hpa@zytor.com
Cc: mingo@kernel.org
Cc: akpm@linux-foundation.org
Cc: torvalds@linux-foundation.org
Link: http://lkml.kernel.org/r/20170314150645.g4tdyoszlcbajmna@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
raid1.c: fix a trivial typo in comments of freeze_array().
Cc: Jack Wang <jack.wang.usish@gmail.com>
Cc: Guoqing Jiang <gqjiang@suse.com>
Cc: John Stoffel <john@stoffel.org>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Zhilong Liu <zlliu@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If we have scheduling enabled, we jump directly to insert-and-run.
That's fine, but we run the queue async and we don't pass in information
on whether we can block from this context or not. Fixup both these
cases.
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Before this patch, device InJournal will be included in prexor
(SYNDROME_SRC_WANT_DRAIN) but not in reconstruct (SYNDROME_SRC_WRITTEN). So it
will break parity calculation. With srctype == SYNDROME_SRC_WRITTEN, we need
include both dev with non-null ->written and dev with R5_InJournal. This fixes
logic in 1e6d690(md/r5cache: caching phase of r5cache)
Cc: stable@vger.kernel.org (v4.10+)
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Commit 4e1f780032c5 ("mmc: block: break out mmc_blk_rw_cmd_abort()")
assumed the request had not completed, but in one case it had. Fix that.
Fixes: 4e1f780032c5 ("mmc: block: break out mmc_blk_rw_cmd_abort()")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Commit 15520111500c ("mmc: core: Further fix thread wake-up") allowed a
queue to release the host with is_waiting_last_req set to true. A queue
waiting to claim the host will not reset it, which can result in the
queue getting stuck in a loop.
Fixes: 15520111500c ("mmc: core: Further fix thread wake-up")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
HS400-ES devices fail to initialize with the following error messages.
mmc1: power class selection to bus width 8 ddr 0 failed
mmc1: error -110 whilst initialising MMC card
This was seen on Samsung Chromebook Plus. Code analysis points to
commit 3d4ef329757c ("mmc: core: fix multi-bit bus width without
high-speed mode"), which attempts to set the bus width for all but
HS200 devices unconditionally. However, for HS400-ES, the bus width
is already selected.
Cc: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Fixes: 3d4ef329757c ("mmc: core: fix multi-bit bus width ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Check that the sink really declared 12bpc support before we enable it.
This should not actually never happen since it's mandatory for HDMI
sinks to support 12bpc if they support any deep color modes. But
reality disagrees with the theory and there are actually sinks in
the wild that violate the spec.
v2: Fix the output_types check
Update commit message to state that these things are in fact real
Cc: stable@vger.kernel.org
Cc: Nicholas Sielicki <nicholas.sielicki@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99250
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170213175818.24958-1-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit c750bdd3e7e204cc88b32806c3864487a03cd84b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
sdhci_arasan_get_timeout_clock() divides the frequency it has with (1 <<
(13 + divisor)).
However, the divisor is not some Arasan-specific value, but instead is
just the Data Timeout Counter Value from the SDHCI Timeout Control
Register.
Applying it here like this is wrong as the sdhci driver already takes
that value into account when calculating timeouts, and in fact it *sets*
that register value based on how long a timeout is wanted.
Additionally, sdhci core interprets the .get_timeout_clock callback
return value as if it were read from hardware registers, i.e. the unit
should be kHz or MHz depending on SDHCI_TIMEOUT_CLK_UNIT capability bit.
This bit is set at least on the tested Zynq-7000 SoC.
With the tested hardware (SDHCI_TIMEOUT_CLK_UNIT set) this results in
too high a timeout clock rate being reported, causing the core to use
longer-than-needed timeouts. Additionally, on a partitioned MMC
(therefore having erase_group_def bit set) mmc_calc_max_discard()
disables discard support as it looks like controller does not support
the long timeouts needed for that.
Do not apply the extra divisor and return the timeout clock in the
expected unit.
Tested with a Zynq-7000 SoC and a partitioned Toshiba THGBMAG5A1JBAWR
eMMC card.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: e3ec3a3d11ad ("mmc: arasan: Add driver for Arasan SDHCI")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The rcu_barrier() takes the cpu_hotplug mutex which itself is not
reclaim-safe, and so rcu_barrier() is illegal from inside the shrinker.
[ 309.661373] =========================================================
[ 309.661376] [ INFO: possible irq lock inversion dependency detected ]
[ 309.661380] 4.11.0-rc1-CI-CI_DRM_2333+ #1 Tainted: G W
[ 309.661383] ---------------------------------------------------------
[ 309.661386] gem_exec_gttfil/6435 just changed the state of lock:
[ 309.661389] (rcu_preempt_state.barrier_mutex){+.+.-.}, at: [<ffffffff81100731>] _rcu_barrier+0x31/0x160
[ 309.661399] but this lock took another, RECLAIM_FS-unsafe lock in the past:
[ 309.661402] (cpu_hotplug.lock){+.+.+.}
[ 309.661404]
and interrupts could create inverse lock ordering between them.
[ 309.661410]
other info that might help us debug this:
[ 309.661414] Possible interrupt unsafe locking scenario:
[ 309.661417] CPU0 CPU1
[ 309.661419] ---- ----
[ 309.661421] lock(cpu_hotplug.lock);
[ 309.661425] local_irq_disable();
[ 309.661432] lock(rcu_preempt_state.barrier_mutex);
[ 309.661441] lock(cpu_hotplug.lock);
[ 309.661446] <Interrupt>
[ 309.661448] lock(rcu_preempt_state.barrier_mutex);
[ 309.661453]
*** DEADLOCK ***
[ 309.661460] 4 locks held by gem_exec_gttfil/6435:
[ 309.661464] #0: (sb_writers#10){.+.+.+}, at: [<ffffffff8120d83d>] vfs_write+0x17d/0x1f0
[ 309.661475] #1: (debugfs_srcu){......}, at: [<ffffffff81320491>] debugfs_use_file_start+0x41/0xa0
[ 309.661486] #2: (&attr->mutex){+.+.+.}, at: [<ffffffff8123a3e7>] simple_attr_write+0x37/0xe0
[ 309.661495] #3: (&dev->struct_mutex){+.+.+.}, at: [<ffffffffa0091b4a>] i915_drop_caches_set+0x3a/0x150 [i915]
[ 309.661540]
the shortest dependencies between 2nd lock and 1st lock:
[ 309.661547] -> (cpu_hotplug.lock){+.+.+.} ops: 829 {
[ 309.661553] HARDIRQ-ON-W at:
[ 309.661560] __lock_acquire+0x5e5/0x1b50
[ 309.661565] lock_acquire+0xc9/0x220
[ 309.661572] __mutex_lock+0x6e/0x990
[ 309.661576] mutex_lock_nested+0x16/0x20
[ 309.661583] get_online_cpus+0x61/0x80
[ 309.661590] kmem_cache_create+0x25/0x1d0
[ 309.661596] debug_objects_mem_init+0x30/0x249
[ 309.661602] start_kernel+0x341/0x3fe
[ 309.661607] x86_64_start_reservations+0x2a/0x2c
[ 309.661612] x86_64_start_kernel+0x173/0x186
[ 309.661619] verify_cpu+0x0/0xfc
[ 309.661622] SOFTIRQ-ON-W at:
[ 309.661627] __lock_acquire+0x611/0x1b50
[ 309.661632] lock_acquire+0xc9/0x220
[ 309.661636] __mutex_lock+0x6e/0x990
[ 309.661641] mutex_lock_nested+0x16/0x20
[ 309.661646] get_online_cpus+0x61/0x80
[ 309.661650] kmem_cache_create+0x25/0x1d0
[ 309.661655] debug_objects_mem_init+0x30/0x249
[ 309.661660] start_kernel+0x341/0x3fe
[ 309.661664] x86_64_start_reservations+0x2a/0x2c
[ 309.661669] x86_64_start_kernel+0x173/0x186
[ 309.661674] verify_cpu+0x0/0xfc
[ 309.661677] RECLAIM_FS-ON-W at:
[ 309.661682] mark_held_locks+0x6f/0xa0
[ 309.661687] lockdep_trace_alloc+0xb3/0x100
[ 309.661693] kmem_cache_alloc_trace+0x31/0x2e0
[ 309.661699] __smpboot_create_thread.part.1+0x27/0xe0
[ 309.661704] smpboot_create_threads+0x61/0x90
[ 309.661709] cpuhp_invoke_callback+0x9c/0x8a0
[ 309.661713] cpuhp_up_callbacks+0x31/0xb0
[ 309.661718] _cpu_up+0x7a/0xc0
[ 309.661723] do_cpu_up+0x5f/0x80
[ 309.661727] cpu_up+0xe/0x10
[ 309.661734] smp_init+0x71/0xb3
[ 309.661738] kernel_init_freeable+0x94/0x19e
[ 309.661743] kernel_init+0x9/0xf0
[ 309.661748] ret_from_fork+0x2e/0x40
[ 309.661752] INITIAL USE at:
[ 309.661757] __lock_acquire+0x234/0x1b50
[ 309.661761] lock_acquire+0xc9/0x220
[ 309.661766] __mutex_lock+0x6e/0x990
[ 309.661771] mutex_lock_nested+0x16/0x20
[ 309.661775] get_online_cpus+0x61/0x80
[ 309.661780] __cpuhp_setup_state+0x44/0x170
[ 309.661785] page_alloc_init+0x23/0x3a
[ 309.661790] start_kernel+0x124/0x3fe
[ 309.661794] x86_64_start_reservations+0x2a/0x2c
[ 309.661799] x86_64_start_kernel+0x173/0x186
[ 309.661804] verify_cpu+0x0/0xfc
[ 309.661807] }
[ 309.661813] ... key at: [<ffffffff81e37690>] cpu_hotplug+0xb0/0x100
[ 309.661817] ... acquired at:
[ 309.661821] lock_acquire+0xc9/0x220
[ 309.661825] __mutex_lock+0x6e/0x990
[ 309.661829] mutex_lock_nested+0x16/0x20
[ 309.661833] get_online_cpus+0x61/0x80
[ 309.661837] _rcu_barrier+0x9f/0x160
[ 309.661841] rcu_barrier+0x10/0x20
[ 309.661847] netdev_run_todo+0x5f/0x310
[ 309.661852] rtnl_unlock+0x9/0x10
[ 309.661856] default_device_exit_batch+0x133/0x150
[ 309.661862] ops_exit_list.isra.0+0x4d/0x60
[ 309.661866] cleanup_net+0x1d8/0x2c0
[ 309.661872] process_one_work+0x1f4/0x6d0
[ 309.661876] worker_thread+0x49/0x4a0
[ 309.661881] kthread+0x107/0x140
[ 309.661884] ret_from_fork+0x2e/0x40
[ 309.661890] -> (rcu_preempt_state.barrier_mutex){+.+.-.} ops: 179 {
[ 309.661896] HARDIRQ-ON-W at:
[ 309.661901] __lock_acquire+0x5e5/0x1b50
[ 309.661905] lock_acquire+0xc9/0x220
[ 309.661910] __mutex_lock+0x6e/0x990
[ 309.661914] mutex_lock_nested+0x16/0x20
[ 309.661919] _rcu_barrier+0x31/0x160
[ 309.661923] rcu_barrier+0x10/0x20
[ 309.661928] netdev_run_todo+0x5f/0x310
[ 309.661932] rtnl_unlock+0x9/0x10
[ 309.661936] default_device_exit_batch+0x133/0x150
[ 309.661941] ops_exit_list.isra.0+0x4d/0x60
[ 309.661946] cleanup_net+0x1d8/0x2c0
[ 309.661951] process_one_work+0x1f4/0x6d0
[ 309.661955] worker_thread+0x49/0x4a0
[ 309.661960] kthread+0x107/0x140
[ 309.661964] ret_from_fork+0x2e/0x40
[ 309.661968] SOFTIRQ-ON-W at:
[ 309.661972] __lock_acquire+0x611/0x1b50
[ 309.661977] lock_acquire+0xc9/0x220
[ 309.661981] __mutex_lock+0x6e/0x990
[ 309.661986] mutex_lock_nested+0x16/0x20
[ 309.661990] _rcu_barrier+0x31/0x160
[ 309.661995] rcu_barrier+0x10/0x20
[ 309.661999] netdev_run_todo+0x5f/0x310
[ 309.662003] rtnl_unlock+0x9/0x10
[ 309.662008] default_device_exit_batch+0x133/0x150
[ 309.662013] ops_exit_list.isra.0+0x4d/0x60
[ 309.662017] cleanup_net+0x1d8/0x2c0
[ 309.662022] process_one_work+0x1f4/0x6d0
[ 309.662027] worker_thread+0x49/0x4a0
[ 309.662031] kthread+0x107/0x140
[ 309.662035] ret_from_fork+0x2e/0x40
[ 309.662039] IN-RECLAIM_FS-W at:
[ 309.662043] __lock_acquire+0x638/0x1b50
[ 309.662048] lock_acquire+0xc9/0x220
[ 309.662053] __mutex_lock+0x6e/0x990
[ 309.662058] mutex_lock_nested+0x16/0x20
[ 309.662062] _rcu_barrier+0x31/0x160
[ 309.662067] rcu_barrier+0x10/0x20
[ 309.662089] i915_gem_shrink_all+0x33/0x40 [i915]
[ 309.662109] i915_drop_caches_set+0x141/0x150 [i915]
[ 309.662114] simple_attr_write+0xc7/0xe0
[ 309.662119] full_proxy_write+0x4f/0x70
[ 309.662124] __vfs_write+0x23/0x120
[ 309.662128] vfs_write+0xc6/0x1f0
[ 309.662133] SyS_write+0x44/0xb0
[ 309.662138] entry_SYSCALL_64_fastpath+0x1c/0xb1
[ 309.662142] INITIAL USE at:
[ 309.662147] __lock_acquire+0x234/0x1b50
[ 309.662151] lock_acquire+0xc9/0x220
[ 309.662156] __mutex_lock+0x6e/0x990
[ 309.662160] mutex_lock_nested+0x16/0x20
[ 309.662165] _rcu_barrier+0x31/0x160
[ 309.662169] rcu_barrier+0x10/0x20
[ 309.662174] netdev_run_todo+0x5f/0x310
[ 309.662178] rtnl_unlock+0x9/0x10
[ 309.662183] default_device_exit_batch+0x133/0x150
[ 309.662188] ops_exit_list.isra.0+0x4d/0x60
[ 309.662192] cleanup_net+0x1d8/0x2c0
[ 309.662197] process_one_work+0x1f4/0x6d0
[ 309.662202] worker_thread+0x49/0x4a0
[ 309.662206] kthread+0x107/0x140
[ 309.662210] ret_from_fork+0x2e/0x40
[ 309.662214] }
[ 309.662220] ... key at: [<ffffffff81e4e1c8>] rcu_preempt_state+0x508/0x780
[ 309.662225] ... acquired at:
[ 309.662229] check_usage_forwards+0x12b/0x130
[ 309.662233] mark_lock+0x360/0x6f0
[ 309.662237] __lock_acquire+0x638/0x1b50
[ 309.662241] lock_acquire+0xc9/0x220
[ 309.662245] __mutex_lock+0x6e/0x990
[ 309.662249] mutex_lock_nested+0x16/0x20
[ 309.662253] _rcu_barrier+0x31/0x160
[ 309.662257] rcu_barrier+0x10/0x20
[ 309.662279] i915_gem_shrink_all+0x33/0x40 [i915]
[ 309.662298] i915_drop_caches_set+0x141/0x150 [i915]
[ 309.662303] simple_attr_write+0xc7/0xe0
[ 309.662307] full_proxy_write+0x4f/0x70
[ 309.662311] __vfs_write+0x23/0x120
[ 309.662315] vfs_write+0xc6/0x1f0
[ 309.662319] SyS_write+0x44/0xb0
[ 309.662323] entry_SYSCALL_64_fastpath+0x1c/0xb1
[ 309.662329]
stack backtrace:
[ 309.662335] CPU: 1 PID: 6435 Comm: gem_exec_gttfil Tainted: G W 4.11.0-rc1-CI-CI_DRM_2333+ #1
[ 309.662342] Hardware name: Hewlett-Packard HP Compaq 8100 Elite SFF PC/304Ah, BIOS 786H1 v01.13 07/14/2011
[ 309.662348] Call Trace:
[ 309.662354] dump_stack+0x67/0x92
[ 309.662359] print_irq_inversion_bug.part.19+0x1a4/0x1b0
[ 309.662365] check_usage_forwards+0x12b/0x130
[ 309.662369] mark_lock+0x360/0x6f0
[ 309.662374] ? print_shortest_lock_dependencies+0x1a0/0x1a0
[ 309.662379] __lock_acquire+0x638/0x1b50
[ 309.662383] ? __mutex_unlock_slowpath+0x3e/0x2e0
[ 309.662388] ? trace_hardirqs_on+0xd/0x10
[ 309.662392] ? _rcu_barrier+0x31/0x160
[ 309.662396] lock_acquire+0xc9/0x220
[ 309.662400] ? _rcu_barrier+0x31/0x160
[ 309.662404] ? _rcu_barrier+0x31/0x160
[ 309.662409] __mutex_lock+0x6e/0x990
[ 309.662412] ? _rcu_barrier+0x31/0x160
[ 309.662416] ? _rcu_barrier+0x31/0x160
[ 309.662421] ? synchronize_rcu_expedited+0x35/0xb0
[ 309.662426] ? _raw_spin_unlock_irqrestore+0x52/0x60
[ 309.662434] mutex_lock_nested+0x16/0x20
[ 309.662438] _rcu_barrier+0x31/0x160
[ 309.662442] rcu_barrier+0x10/0x20
[ 309.662464] i915_gem_shrink_all+0x33/0x40 [i915]
[ 309.662484] i915_drop_caches_set+0x141/0x150 [i915]
[ 309.662489] simple_attr_write+0xc7/0xe0
[ 309.662494] full_proxy_write+0x4f/0x70
[ 309.662498] __vfs_write+0x23/0x120
[ 309.662503] ? rcu_read_lock_sched_held+0x75/0x80
[ 309.662507] ? rcu_sync_lockdep_assert+0x2a/0x50
[ 309.662512] ? __sb_start_write+0x102/0x210
[ 309.662516] ? vfs_write+0x17d/0x1f0
[ 309.662520] vfs_write+0xc6/0x1f0
[ 309.662524] ? trace_hardirqs_on_caller+0xe7/0x200
[ 309.662529] SyS_write+0x44/0xb0
[ 309.662533] entry_SYSCALL_64_fastpath+0x1c/0xb1
[ 309.662537] RIP: 0033:0x7f507eac24a0
[ 309.662541] RSP: 002b:00007fffda8720e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 309.662548] RAX: ffffffffffffffda RBX: ffffffff81482bd3 RCX: 00007f507eac24a0
[ 309.662552] RDX: 0000000000000005 RSI: 00007fffda8720f0 RDI: 0000000000000005
[ 309.662557] RBP: ffffc9000048bf88 R08: 0000000000000000 R09: 000000000000002c
[ 309.662561] R10: 0000000000000014 R11: 0000000000000246 R12: 00007fffda872230
[ 309.662566] R13: 00007fffda872228 R14: 0000000000000201 R15: 00007fffda8720f0
[ 309.662572] ? __this_cpu_preempt_check+0x13/0x20
Fixes: 0eafec6d3244 ("drm/i915: Enable lockless lookup of request tracking via RCU")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100192
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.9+
Link: http://patchwork.freedesktop.org/patch/msgid/20170314115019.18127-1-chris@chris-wilson.co.uk
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
I want to split up a few more things and document some details better
(like how exactly to subclass drm_atomic_state). And maybe also split
up the helpers a bit per-topic, but this should be a ok-ish start for
better atomic overview.
v2: Spelling and clarifications (Eric).
v3: Implement suggestion from Gabriel to fix the graph.
v4: Review from Laurent.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Eric Anholt <eric@anholt.net>
Cc: Eric Anholt <eric@anholt.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302151638.1882-6-daniel.vetter@ffwll.ch
|
|
Resulted in confusion a few times in the past.
v2: Spelling fix (Eric).
Cc: Eric Anholt <eric@anholt.net>
Acked-by: Eric Anholt <eric@anholt.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302151638.1882-5-daniel.vetter@ffwll.ch
|
|
First overview text (if there is any), then headers (since generally
you want to start out with the data structures), then all the other
stuff with functions.
Most of this is pre-shpinx, since with the old docbook only the
overview stuff was pulled in directly. Everything else was put in a
per-section index, so include order didn't really matter.
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302151638.1882-4-daniel.vetter@ffwll.ch
|
|
Oh, the shiny and pretties!
v2: Review from Laurent.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302151638.1882-3-daniel.vetter@ffwll.ch
|
|
Pointer for Markus's image conversion work.
We need this so we can merge all the pretty drm graphs for 4.12.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
The 33rd entry in the pre-CSC gamma table in Geminilake can represent a
value of 1.0 as 17 bits fixed point with one integer bit. However, the
table was generated such that the value of 1.0 would be 0.ffff with
all the intervals scaled accordingly. For instance, 0.5 mapped to
0.7fff instead of 0.8000.
For a reason that is not clear to the author, the rounding seems to be
different when a cursor plane is used, leading to some seemingly random
failures of the kms_cursor_crc igt tests. The differences weren't
perceptible at 8bpc with images captured by a Chamelium device, but did
cause CRC mismatches.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170310101835.29845-1-ander.conselvan.de.oliveira@intel.com
|
|
Sadly there's only 1 driver which can use it, everyone else is special
for some reason:
- gma500 has a horrible runtime PM ioctl wrapper that probably doesn't
really work but meh.
- i915 needs special compat_ioctl handler because regrets.
- arcgpu needs to fixup the pgprot because (no idea why it can't do
that in the fault handler like everyone else).
- tegra does even worse stuff with pgprot
- udl does something with vm_flags too ...
- cma helpers, etnaviv, mtk, msm, rockchip, omap all implement some
variation on prefaulting.
- exynos is exynos, I got lost in the midlayers.
- vc4 has to reinvent half of cma helpers because those are too much
midlayer, plus vm_flags dances.
- vgem also seems unhappy with the default vm_flags.
So pretty sad divergence and I'm sure we could do better, but not
really an idea. Oh well, maybe this macro here helps to encourage more
consistency at least going forward.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-25-daniel.vetter@ffwll.ch
|
|
Less code ftw.
This converts all drivers except the tinydrm helper module. That one
needs more work, since it gets the THIS_MODULE reference from
tinydrm.ko instead of the actual driver module like it should.
Probably needs a similar trick like I used here with generating the
entire struct with a macro.
Cc: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-24-daniel.vetter@ffwll.ch
|
|
I didn't spot anything that would require ordering here (well not
anywhere else either), and I'm trying to unify at least modern drivers
on one close hook.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-18-daniel.vetter@ffwll.ch
|
|
Well, mostly drm_file.h, and clean up all related things:
- I didnt' figure out the difference between preclose and postclose.
The existing explanation in drm-internals.rst didn't convince me,
since it's also really outdated - we clean up pending DRM events in
the core nowadays. I put a FIXME in for the future.
- Another FIXME is to have a macro for default fops.
- Lots of links all around, main areas are to tie the overview in
drm_file.c more into the callbacks in struct drm_device, and the
other is to link render/primary node code to the right sections in
drm-uapi.rst.
- Also moved the open/close stuff to drm_drv.h from drm-internals.rst,
seems like the better place for that information. Since that section
was rather outdated this amounted to full-on rewrite.
A big missing piece here is some overview graph, but I think better to
wait with that one until drm_device and drm_driver are also fully
documented.
v2: Nits from Sean.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-12-daniel.vetter@ffwll.ch
|
|
We might as well dump the drm_file pointer, that's about as useful
a cookie as the pid. Noticed while typing docs for drm_file and friends.
Since the only consumer of this is the tracepoints I think we can safely
change this - those tracepoints should not be uapi relevant at all. It
all goes back to
commit b9c2c9ae882f058084e13e339925dbf8d2d20271
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Jul 1 16:48:09 2010 -0700
drm: add per-event vblank event trace points
which doesn't give a special justification for using pid over a pointer.
Also note that the nouveau code setting it is entirely pointless:
Since this isn't a vblank event, it will never hit the vblank
tracepoints.
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-11-daniel.vetter@ffwll.ch
|
|
There's really not a reason afaics that we can't just clean up
everything at the end, in the terminal postclose hook: Since this is
closing a file descriptor we know no one else can have a reference or
a thread doing something with that drm_file except the close code.
Ordering shouldn't matter, as long as we don't kfree before we clean
stuff up.
In the past this was more relevant when drivers still had to track and
clean up pending drm events, but that's all done by the core now.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-13-daniel.vetter@ffwll.ch
|
|
As i915_gem_reset_finish() undoes the steps from
i915_gem_reset_prepare() to leave the system in a fully-working state,
e.g. to be able to free the breadcrumb signal threads, make sure that we
always call it even on the error path.
Fixes: da9a796f5475 ("drm/i915: Split GEM resetting into 3 phases")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170212172002.23072-2-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit 8d613c539c74fa9055f88f4116196d7c820bd98f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Touching HW while clocks are off is a serious error and for instance
breaks suspend functionality. After this patch tilcdc_crtc_update_fb()
always updates the primary plane's framebuffer pointer, increases fb's
reference count and stores vblank event. tilcdc_crtc_update_fb() only
writes the fb's DMA address to HW if the crtc is enabled, as
tilcdc_crtc_enable() takes care of writing the address on enable.
This patch also refactors the tilcdc_crtc_update_fb() a bit. Number of
subsequent small changes had made it almost unreadable. There should
be no other functional changes but checking the CRTC's enable
state. However, the locking goes a bit differently and some of the
redundant checks have been removed in this new version.
The enable_lock should be enough to protect the access to
tilcdc_crtc->enabled. The irq_lock protects the access to last_vblank
and next_fb. The check for vrefresh and last_vblank being valid is
redundant, as the vrefresh should be always valid if the CRTC is
enabled and now last_vblank should be too, because it is initialized
to current time when CRTC raster is enabled. If for some reason the
values are not correctly initialized the division by zero warning is
quite appropriate.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Fix badly hardcoded return return value under fail-label. All goto
branches to the label set the "ret"-variable accordingly.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
|
|
My static checker complains that "release" is uninitialized if
qxl_alloc_release_reserved() fails, so let's add a check for that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170314075410.GB5984@mwanda
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
kmem_cache_alloc returns NULL on error, not ERR_PTR.
Fixes: f5985bf9cadd4e3ed8d5d9a9cbbb2e39cdb81cd9
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1489393346-13874-1-git-send-email-kraxel@redhat.com
|
|
On Baytrail, we manually calculate busyness over the evaluation interval
to avoid issues with miscaluations with RC6 enabled. However, it turns
out that the DOWN_EI interrupt generator is completely bust - it
operates in two modes, continuous or never. Neither of which are
conducive to good behaviour. Stop unmask the DOWN_EI interrupt and just
compute everything from the UP_EI which does seem to correspond to the
desired interval.
v2: Fixup gen6_rps_pm_mask() as well
v3: Inline vlv_c0_above() to combine the now identical elapsed
calculation for up/down and simplify the threshold testing
Fixes: 43cf3bf084ba ("drm/i915: Improved w/a for rps on Baytrail")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170309211232.28878-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170313170617.31564-1-chris@chris-wilson.co.uk
(cherry picked from commit e0e8c7cb6eb68e9256de2d8cbeb481d3701c05ac)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
This patch makes the I915_PARAM_HAS_EXEC_CONSTANTS getparam return 0
(indicating the optional feature is not supported), and makes execbuf
always return -EINVAL if the flags are used.
Apparently, no userspace ever shipped which used this optional feature:
I checked the git history of Mesa, xf86-video-intel, libva, and Beignet,
and there were zero commits showing a use of these flags. Kernel commit
72bfa19c8deb4 apparently introduced the feature prematurely. According
to Chris, the intention was to use this in cairo-drm, but "the use was
broken for gen6", so I don't think it ever happened.
'relative_constants_mode' has always been tracked per-device, but this
has actually been wrong ever since hardware contexts were introduced, as
the INSTPM register is saved (and automatically restored) as part of the
render ring context. The software per-device value could therefore get
out of sync with the hardware per-context value. This meant that using
them is actually unsafe: a client which tried to use them could damage
the state of other clients, causing the GPU to interpret their BO
offsets as absolute pointers, leading to bogus memory reads.
These flags were also never ported to execlist mode, making them no-ops
on Gen9+ (which requires execlists), and Gen8 in the default mode.
On Gen8+, userspace can write these registers directly, achieving the
same effect. On Gen6-7.5, it likely makes sense to extend the command
parser to support them. I don't think anyone wants this on Gen4-5.
Based on a patch by Dave Gordon.
v3: Return -ENODEV for the getparam, as this is what we do for other
obsolete features. Suggested by Chris Wilson.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92448
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170215093446.21291-1-kenneth@whitecape.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170313170433.26843-1-chris@chris-wilson.co.uk
(cherry picked from commit ef0f411f51475f4eebf9fc1b19a85be698af19ff)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
In order to prevent accessing the hpd registers outside of the display
power wells, we should refrain from writing to the registers before the
display interrupts are enabled.
[ 4.740136] WARNING: CPU: 1 PID: 221 at drivers/gpu/drm/i915/intel_uncore.c:795 __unclaimed_reg_debug+0x44/0x50 [i915]
[ 4.740155] Unclaimed read from register 0x1e1110
[ 4.740168] Modules linked in: i915(+) intel_gtt drm_kms_helper prime_numbers
[ 4.740190] CPU: 1 PID: 221 Comm: systemd-udevd Not tainted 4.10.0-rc6+ #384
[ 4.740203] Hardware name: / , BIOS PYBSWCEL.86A.0027.2015.0507.1758 05/07/2015
[ 4.740220] Call Trace:
[ 4.740236] dump_stack+0x4d/0x6f
[ 4.740251] __warn+0xc1/0xe0
[ 4.740265] warn_slowpath_fmt+0x4a/0x50
[ 4.740281] ? insert_work+0x77/0xc0
[ 4.740355] ? fwtable_write32+0x90/0x130 [i915]
[ 4.740431] __unclaimed_reg_debug+0x44/0x50 [i915]
[ 4.740507] fwtable_read32+0xd8/0x130 [i915]
[ 4.740575] i915_hpd_irq_setup+0xa5/0x100 [i915]
[ 4.740649] intel_hpd_init+0x68/0x80 [i915]
[ 4.740716] i915_driver_load+0xe19/0x1380 [i915]
[ 4.740784] i915_pci_probe+0x32/0x90 [i915]
[ 4.740799] pci_device_probe+0x8b/0xf0
[ 4.740815] driver_probe_device+0x2b6/0x450
[ 4.740828] __driver_attach+0xda/0xe0
[ 4.740841] ? driver_probe_device+0x450/0x450
[ 4.740853] bus_for_each_dev+0x5b/0x90
[ 4.740865] driver_attach+0x19/0x20
[ 4.740878] bus_add_driver+0x166/0x260
[ 4.740892] driver_register+0x5b/0xd0
[ 4.740906] ? 0xffffffffa0166000
[ 4.740920] __pci_register_driver+0x47/0x50
[ 4.740985] i915_init+0x5c/0x5e [i915]
[ 4.740999] do_one_initcall+0x3e/0x160
[ 4.741015] ? __vunmap+0x7c/0xc0
[ 4.741029] ? kmem_cache_alloc+0xcf/0x120
[ 4.741045] do_init_module+0x55/0x1c4
[ 4.741060] load_module+0x1f3f/0x25b0
[ 4.741073] ? __symbol_put+0x40/0x40
[ 4.741086] ? kernel_read_file+0x100/0x190
[ 4.741100] SYSC_finit_module+0xbc/0xf0
[ 4.741112] SyS_finit_module+0x9/0x10
[ 4.741125] entry_SYSCALL_64_fastpath+0x17/0x98
[ 4.741135] RIP: 0033:0x7f8559a140f9
[ 4.741145] RSP: 002b:00007fff7509a3e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 4.741161] RAX: ffffffffffffffda RBX: 00007f855aba02d1 RCX: 00007f8559a140f9
[ 4.741172] RDX: 0000000000000000 RSI: 000055b6db0914f0 RDI: 0000000000000011
[ 4.741183] RBP: 0000000000020000 R08: 0000000000000000 R09: 000000000000000e
[ 4.741193] R10: 0000000000000011 R11: 0000000000000246 R12: 000055b6db0854d0
[ 4.741204] R13: 000055b6db091150 R14: 0000000000000000 R15: 000055b6db035924
v2: Set dev_priv->display_irqs_enabled to true for all platforms other
than vlv/chv that manually control the display power domain.
Fixes: 19625e85c6ec ("drm/i915: Enable polling when we don't have hpd")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97798
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lyude <cpaul@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Hans de Goede <jwrdegoede@fedoraproject.org>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170215131547.5064-1-chris@chris-wilson.co.uk
Link: http://patchwork.freedesktop.org/patch/msgid/20170313170231.18633-1-chris@chris-wilson.co.uk
(cherry picked from commit 262fd485ac6b476479f41f00bb104f6a1766ae66)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
When we restart the engines, and we have active requests, a request on
the first engine may complete and queue a request to the second engine
before we try to restart the second engine. That queueing of the
request may race with the engine to restart, and so may corrupt the
current state. Disabling the engine->irq_tasklet prevents the two paths
from writing into ELSP simultaneously (and modifyin the execlists_port[]
at the same time).
Include fixup 1d309634bcf4 ("drm/i915: Kill the tasklet then disable")
Fixes: 821ed7df6e2a ("drm/i915: Update reset path to fix incomplete requests")
Testcase: igt/gem_exec_fence/await-hang
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170208143033.11651-3-chris@chris-wilson.co.uk
Link: http://patchwork.freedesktop.org/patch/msgid/20170313165958.13970-2-chris@chris-wilson.co.uk
(cherry picked from commit 1f7b847d72c3583df5048d83bd945d0c2c524c28)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
This reverts commit bb10d4ec3be4b069bfb61c60ca4f708f58f440f1.
Since commit c8ebfad7a063 ("drm/i915: Ignore OpRegion panel type except
on select machines") we ignore the OpRegion panel type except for
specific machines (handled via a DMI match), so having SKL explicitly
excluded from using the OpRegion panel type is redundant. So let's
remove the SKL check.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308143334.21216-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Currently we do a reset prepare/finish around the call to reset the GPU,
but it looks like we need a later stage after the hw has been
reinitialised to allow GEM to restart itself. Start by splitting the 2
GEM phases into 3:
prepare - before the reset, check if GEM recovered, then stop GEM
reset - after the reset, update GEM bookkeeping
finish - after the re-initialisation following the reset, restart GEM
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170208143033.11651-2-chris@chris-wilson.co.uk
Link: http://patchwork.freedesktop.org/patch/msgid/20170313165958.13970-1-chris@chris-wilson.co.uk
(cherry picked from commit d80270931314a88d79d9bd5e0a5df93c12196375)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
On some DDR controllers, compatible with the sama5d3 one,
the sequence to enter/exit/re-enter the self-refresh mode adds
more constrains than what is currently written in the at91_idle
driver. An actual access to the DDR chip is needed between exit
and re-enter of this mode which is somehow difficult to implement.
This sequence can completely hang the SoC. It is particularly
experienced on parts which embed a L2 cache if the code run
between IDLE calls fits in it...
Moreover, as the intention is to enter and exit pretty rapidly
from IDLE, the power-down mode is a good candidate.
So now we use power-down instead of self-refresh. As we can
simplify the code for sama5d3 compatible DDR controllers,
we instantiate a new sama5d3_ddr_standby() function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # v4.1+
Fixes: 017b5522d5e3 ("ARM: at91: Add new binding for sama5d3-ddramc")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by
qcserial due to a USB VID/PID conflict with an existing Acer
device.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The commits mentioned below adapt the GPIO API to allow more information
to be passed directly through devm_get_gpiod_from_child() in the first
instance. This facilitates the removal of subsequent calls, such as
gpiod_direction_output(). This patch firstly moves to utilise the new
API and secondly removes the now superfluous call do set the direction.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Also drop the header file dummies that only this driver was using]
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The DSPS glue calls del_timer_sync() in its musb_platform_disable()
implementation, which requires the caller to not hold a lock. But
musb_remove() calls musb_platform_disable() will musb->lock held. This
could causes spinlock deadlock.
So change musb_remove() to call musb_platform_disable() without holds
musb->lock. This doesn't impact the musb_platform_disable implementation
in other glue drivers.
root@am335x-evm:~# modprobe -r musb-dsps
[ 126.134879] musb-hdrc musb-hdrc.1: remove, state 1
[ 126.140465] usb usb2: USB disconnect, device number 1
[ 126.146178] usb 2-1: USB disconnect, device number 2
[ 126.416985] musb-hdrc musb-hdrc.1: USB bus 2 deregistered
[ 126.423943]
[ 126.425525] ======================================================
[ 126.431997] [ INFO: possible circular locking dependency detected ]
[ 126.438564] 4.11.0-rc1-00003-g1557f13bca04-dirty #77 Not tainted
[ 126.444852] -------------------------------------------------------
[ 126.451414] modprobe/778 is trying to acquire lock:
[ 126.456523] (((&glue->timer))){+.-...}, at: [<c01b8788>] del_timer_sync+0x0/0xd0
[ 126.464403]
[ 126.464403] but task is already holding lock:
[ 126.470511] (&(&musb->lock)->rlock){-.-...}, at: [<bf30b7f8>] musb_remove+0x50/0x1
30 [musb_hdrc]
[ 126.479965]
[ 126.479965] which lock already depends on the new lock.
[ 126.479965]
[ 126.488531]
[ 126.488531] the existing dependency chain (in reverse order) is:
[ 126.496368]
[ 126.496368] -> #1 (&(&musb->lock)->rlock){-.-...}:
[ 126.502968] otg_timer+0x80/0xec [musb_dsps]
[ 126.507990] call_timer_fn+0xb4/0x390
[ 126.512372] expire_timers+0xf0/0x1fc
[ 126.516754] run_timer_softirq+0x80/0x178
[ 126.521511] __do_softirq+0xc4/0x554
[ 126.525802] irq_exit+0xe8/0x158
[ 126.529735] __handle_domain_irq+0x58/0xb8
[ 126.534583] __irq_usr+0x54/0x80
[ 126.538507]
[ 126.538507] -> #0 (((&glue->timer))){+.-...}:
[ 126.544636] del_timer_sync+0x40/0xd0
[ 126.549066] musb_remove+0x6c/0x130 [musb_hdrc]
[ 126.554370] platform_drv_remove+0x24/0x3c
[ 126.559206] device_release_driver_internal+0x14c/0x1e0
[ 126.565225] bus_remove_device+0xd8/0x108
[ 126.569970] device_del+0x1e4/0x308
[ 126.574170] platform_device_del+0x24/0x8c
[ 126.579006] platform_device_unregister+0xc/0x20
[ 126.584394] dsps_remove+0x14/0x30 [musb_dsps]
[ 126.589595] platform_drv_remove+0x24/0x3c
[ 126.594432] device_release_driver_internal+0x14c/0x1e0
[ 126.600450] driver_detach+0x38/0x6c
[ 126.604740] bus_remove_driver+0x4c/0xa0
[ 126.609407] SyS_delete_module+0x11c/0x1e4
[ 126.614252] __sys_trace_return+0x0/0x10
Fixes: ea2f35c01d5ea ("usb: musb: Fix sleeping function called from invalid context for hdrc glue")
Cc: <stable@vger.kernel.org> #4.9+
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Cleanly iounmap the pointer in error and exit paths.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The CPPI 4.1 driver polls register to workaround the premature TX
interrupt issue, but it causes audio playback underrun when triggered in
Isoch transfers.
Isoch doesn't do back-to-back transfers, the TX should be done by the
time the next transfer is scheduled. So skip this polling workaround for
Isoch transfer.
Fixes: a655f481d83d6 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt")
Cc: <stable@vger.kernel.org> #4.1+
Reported-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
drivers/gpu/drm/tinydrm/mipi-dbi.c:657:2-3: Unneeded semicolon
drivers/gpu/drm/tinydrm/mipi-dbi.c:593:2-3: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170312144636.GA91808@lkp-g5.lkp.intel.com
|
|
The trouble we have is that we can't really test all the shrinker
recursion stuff exhaustively in BAT because any kind of thrashing
stress test just takes too long.
But that leaves a really big gap open, since shrinker recursions are
one of the most annoying bugs. Now lockdep already has support for
checking allocation deadlocks:
- Direct reclaim paths are marked up with
lockdep_set_current_reclaim_state() and
lockdep_clear_current_reclaim_state().
- Any allocation paths are marked with lockdep_trace_alloc().
If we simply mark up our debugfs with the reclaim annotations, any
code and locks taken in there will automatically complete the picture
with any allocation paths we already have, as long as we have a simple
testcase in BAT which throws out a few objects using this interface.
Not stress test or thrashing needed at all.
v2: Need to EXPORT_SYMBOL_GPL to make it compile as a module.
v3: Fixup rebase fail (spotted by Chris).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170312205340.16202-1-daniel.vetter@ffwll.ch
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.
The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms. It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies. The generic config code does not
catch this case because the 64ms is considered a sane enough value.
This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Note that the dereference happens in the cmd and wait_init_done
callbacks which are called during probe.
Fixes: 1ba47da52712 ("uwb: add the i1480 DFU driver")
Cc: stable <stable@vger.kernel.org> # 2.6.28
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
