| Age | Commit message (Collapse) | Author |
|---|
|
In commit b93b1fe3b532 ("iwlwifi: mvm: fix init_dbg flow to work
as expected"), the code was changed to make the stop conditional
on not having failed (and on not having init_dbg), which doesn't
make sense - we should stop the device regardless of failures.
Failure to do so is leading to the device being enabled when it
shouldn't be, and - if it gets re-enabled later - the new context
info code gets confused as paging data wasn't freed.
Remove the invalid error condition again.
Fixes: b93b1fe3b532 ("iwlwifi: mvm: fix init_dbg flow to work as expected")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This appears to happen in some cases, like when iwlmvm is unloaded and
loaded again without also unloading iwlwifi. Warn in this case and free
the paging data to be able to continue without causing corruption and
kernel crashes due to it (otherwise, paging data is overwritten, but
dram->paging_cnt gets to be twice as big as it should be, and then an
eventual free will crash.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
By setting the pointers to NULL at the end, these functions
are made idempotent.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Where possible (all except for "11n_disable", which isn't valid in C)
rename the internal names for module parameters to be the same as the
externally visible names, to aid finding their use etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When receiving a BA_NOTIF on new TX API, it can
contain BAs for several TIDs. Go over them and
reclaim TX for every TID.
Note that although the small API change, the API
version still isn't bumped forward, as this NIC
isn't still officially released.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The BT_COEX command should not be sent to the INIT
firmware image starting from 8000 family.
The firmware team also requested to send the BT_COEX
command after the PHY_DB_CMD and the PHY_CFG_CMD.
While at it:
s/iwl_send_bt_init_conf/iwl_mvm_send_bt_init_conf/
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Print the queue for the existing debug message and add a new
debug message indicating where the RB ended.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
A SCD bug was fixed in the A000 family, allowing to
support aggregations of 64 frames (rather than 63).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Print out both queue IDs to be able to see what went wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When the firmware supports CDB, PHY contexts cannot be modified to
change their band, but need to be added/remove instead. Instead of
relying on iwl_mvm_has_new_tx_api(), check the right FW capa flag
IWL_UCODE_TLV_CAPA_BINDING_CDB_SUPPORT and remove the comment.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add twelve new PCI IDs for the 9560 series.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add a new config struct for the new a000 2ax series and add
the five PCI ID for it.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no reason to pass mvm and trig as parameters to the macro,
since it will be expanded inside the function itself. Also remove the
bogus buf parameter which doesn't exist and is not used.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The sta_id variable is used as an index in an array, should be unsigned.
Found by Klocwork.
Fixes: 9f9af3d7d303 ("iwlwifi: mvm: re-aggregate shared queue after unsharing")
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
A hardware issue on 9000 series devices sometimes causes RF-kill
interrupts to not be propagated to the host properly if ASPM is
enabled. Work around this by setting the right hardware bit to
allow it to interrupt the host for this reason (rfkill).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Due to a hardware issue, certain power saving had to be
disabled. However, this issue was fixed in B-step, so the
workaround only needs to apply to A-step.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Some static checkers (e.g. smatch) complain if a non-constant
format string is used, even if that's a static const variable.
Since there's no impact on code generation, just change those
format strings to be macros.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Fix the kernel-doc, and remove some fields even the firmware doesn't
use in ToF, RX, scan, station and generic FW APIS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Fix various "Excess struct/union/enum/typedef member '...' description
in '...'" warnings from kernel-doc, mostly caused by typos.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add a debugfs entry to get a verbose description of the power settings
used in each band with the currently selected SAR geographic profile.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We are going to add debugfs entry to retrieve the current geographic
profile being used in the FW. Currently the driver reads those tables
from the BIOS and passes them to the FW.
To prepare for this retrieving we want to store those
tables in the driver.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Here the functions reloc_insn_movw() & reloc_insn_imm() are used
to read, modify and write back ARM instructions, which are always
stored in memory in little-endian order. These values are thus
correctly converted to/from native order but the pointers used to
hold their addresses are declared as for native order values.
Fix this by declaring the pointers as __le32* and remove the
casts that are now unneeded.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
aarch64_insn_write() is used to write an instruction.
As on ARM64 in-memory instructions are always stored
in little-endian order, this function, taking the instruction
opcode in native order, correctly convert it to little-endian
before sending it to an helper function __aarch64_insn_write()
which will do the effective write.
This is all good, but the variable and argument holding the
converted value are not annotated for a little-endian value
but left for native values.
Fix this by adjusting the prototype of the helper and
directly using the result of cpu_to_le32() without passing
by an intermediate variable (which was not a distinct one
but the same as the one holding the native value).
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The function arch64_insn_read() is used to read an instruction.
On AM64 instructions are always stored in little-endian order
and thus the function correctly do a little-to-native endian
conversion to the value just read.
However, the variable used to hold the value before the conversion
is not declared for a little-endian value but for a native one.
Fix this by using the correct type for the declaration: __le32
Note: This only works because the function reading the value,
probe_kernel_read((), takes a void pointer and void pointers
are endian-agnostic. Otherwise probe_kernel_read() should
also be properly annotated (or worse, need to be specialized).
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Here we're reading thumb or ARM instructions, which are always
stored in memory in little-endian order. These values are thus
correctly converted to native order but the intermediate value
should be annotated as for little-endian values.
Fix this by declaring the intermediate var as __le32 or __le16.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Here we're reading thumb or ARM instructions, which are always
stored in memory in little-endian order. These values are thus
correctly converted to native order but the intermediate value
should be annotated as for little-endian values.
Fix this by declaring the intermediate var as __le32 or __le16.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
With CONFIG_RAS disabled, we get two harmless warnings about
unused functions:
include/linux/ras.h:37:13: error: 'log_arm_hw_error' defined but not used [-Werror=unused-function]
static void log_arm_hw_error(struct cper_sec_proc_arm *err) { return; }
include/linux/ras.h:33:13: error: 'log_non_standard_event' defined but not used [-Werror=unused-function]
static void log_non_standard_event(const guid_t *sec_type,
Clearly these are meant to be 'inline', like the other stubs
in the same header.
Fixes: 297b64c74385 ("ras: acpi / apei: generate trace event for unrecognized CPER section")
Fixes: e9279e83ad1f ("trace, ras: add ARM processor error trace event")
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The sdio_sb group is composed of 6 pins and not 5.
Reported-by: Ken Ma <make@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If north bridge selection register bit1 is clear, pins [10:8] are for
SDIO0 Resetn, Wakeup, and PDN while if bit1 is set, pins [10:8]are for
GPIO; when bit1 is clear, pin 9 and pin 10 can be used for uart2 RTSn
and CTSn, so bit1 should be added to uart2 group and it must be set
for both "gpio" and "uart" functions of uart2 group.
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIOEVENT_REQUEST_BOTH_EDGES is not a single flag, but a binary OR of
GPIOEVENT_REQUEST_RISING_EDGE and GPIOEVENT_REQUEST_FALLING_EDGE.
The expression 'le->eflags & GPIOEVENT_REQUEST_BOTH_EDGES' we'll get
evaluated to true even if only one event type was requested.
Fix it by checking both RISING & FALLING flags explicitly.
Cc: stable@vger.kernel.org
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events")
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We get a warning during boot with enabled EARLY_PRINTK that
we try to set a irq_chip without data. This is caused by ignoring
the return value of irq_of_parse_and_map(). So avoid calling
gpiochip_set_chained_irqchip() in error case.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 85ae9e512f43 ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Non-existent or empty DIMM slots result in error return from
RD_REGP(). But we shouldn't give up on failure.
So long as we find at least one DIMM we can continue.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170628234407.21521-1-tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
In the i5000 and i5400 drivers, the NRECMEMB register is defined as a
16-bit value, which results in wrong shifts in the code, as reported by
sparse.
In the datasheets ([1], section 3.9.22.20 and [2], section 3.9.22.21),
this register is a 32-bit register. A u32 value for the register fixes
the wrong shifts warnings and matches the datasheet.
Also fix the mask to access to the CAS bits [27:16] in the i5000 driver.
[1]: https://www.intel.com/content/dam/doc/datasheet/5000p-5000v-5000z-chipset-memory-controller-hub-datasheet.pdf
[2]: https://www.intel.se/content/dam/doc/datasheet/5400-chipset-memory-controller-hub-datasheet.pdf
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170629005729.8478-1-jeremy.lefaure@lse.epita.fr
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
Stephen reported the following build warning in UP:
kernel/sched/fair.c:2657:9: warning: 'struct sched_domain' declared inside
parameter list
^
/home/sfr/next/next/kernel/sched/fair.c:2657:9: warning: its scope is only this
definition or declaration, which is probably not what you want
Hide the numa_wake_affine() inline stub on UP builds to get rid of it.
Fixes: 3fed382b46ba ("sched/numa: Implement NUMA node level wake_affine()")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
|
|
When rpmsg devices are expected to be matched based on their compatible
the modalias should reflect this, so that module autoloading has a
chance to match and load the appropriate module.
Tested-by: Rob Clark <robdclark@gmail.com>
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Commit fc5cbf0c94b6 (PM / Domains: Support for multiple states) split
out some code out of default_power_down_ok() function so the
documentation has to be moved to appropriate place.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
of_genpd_remove_last() iterates over list of domains and removes
matching element thus it has to use safe version of list iteration.
Fixes: 17926551c98a (PM / Domains: Add support for removing nested PM domains by provider)
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
of_genpd_del_provider() iterates over list of domain provides and
removes matching element thus it has to use safe version of list
iteration.
Fixes: aa42240ab254 (PM / Domains: Add generic OF-based PM domain look-up)
Cc: 3.19+ <stable@vger.kernel.org> # 3.19+
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
pm_genpd_remove_subdomain() iterates over domain's master_links list and
removes matching element thus it has to use safe version of list
iteration.
Fixes: f721889ff65a ("PM / Domains: Support for generic I/O PM domains (v8)")
Cc: 3.1+ <stable@vger.kernel.org> # 3.1+
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
genpd_syscore_switch() had two problems:
1. It silently assumed that device, it is being called for, belongs
to generic power domain and used container_of() on its power
domain pointer. Such assumption might not be true always.
2. It iterated over list of generic power domains without holding
gpd_list_lock mutex thus list could have been modified at the same
time.
Usage of genpd_lookup_dev() solves both problems as it is safe a call
for non-generic power domains and uses mutex when iterating.
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently genpd installs its own noirq callbacks, but never calls down
to the driver's corresponding callbacks. Add these calls.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The only user of thread_saved_pc() in non-arch-specific code was removed
in commit 8243d5597793 ("sched/core: Remove pointless printout in
sched_show_task()"). Remove the implementations as well.
Some architectures use thread_saved_pc() in their arch-specific code.
Leave their thread_saved_pc() intact.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The timers cpu base lock could not be converted to a raw spinlock becaue
the lock held time was non-deterministic due to cascading and long lasting
timer wheel traversals.
The rework of the timer wheel to the new non-cascading model removed also
the wheel traversals and the lock held times are deterministic now. This
allows to make the lock raw and thereby unbreaks NOHz* on preempt-RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20170627161538.30257-1-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
ASUS GL720VMK is also affected by the EC GPE preference issue.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some Asus laptops (verified on X550VXK/FX502VD/FX502VE) get no
interrupts when pressing media keys thus the corresponding functions
are not invoked. It's due to the _GPE defines in DSDT for EC returns
differnt value compared to the GPE Number in ECDT. Confirmed with Asus
that the vale in ECDT is the correct one. This commit uses DMI quirks
to prevent calling _GPE when doing ec_parse_device() and keep the ECDT
GPE number setting for the EC device.
With previous commit, it is ensured that if there is an ECDT, it can
always be kept as boot_ec, this patch thus can implement a quirk on
top of the determined ECDT boot_ec.
Link: https://phabricator.endlessm.com/T16033
Link: https://phabricator.endlessm.com/T16722
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195651
Tested-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We prepared _INI/_STA methods for \_SB, \_SB.PCI0, \_SB.LID0 and
\_SB.EC, _HID(PNP0C09)/_CRS/_GPE for \_SB.EC to poke Windows behavior
with qemu, we got the following execution sequence:
\_SB._INI
\_SB.PCI0._STA
\_SB.LID0._STA
\_SB.EC._STA
\_SB.PCI0._INI
\_SB.LID0._INI
\_SB.EC._INI
There is no extra DSDT EC device enumeration process occurring before
the main ACPI device enumeration process. That means acpi_ec_dsdt_probe()
is not Windows-compatible.
Tracking back, it was added by the following commit:
Commit: c5279dee26c0e8d7c4200993bfc4b540d2469598
Subject: ACPI: EC: Add some basic check for ECDT data
but that commit was misguided.
Why we shouldn't enumerate DSDT EC before the main ACPI device
enumeration?
The only way to know if the DSDT EC is valid would be to evaluate its
_STA control method, but it's not safe to evaluate this control method
that early and out of the ACPI enumeration process, because _STA may
refer to entities (such as resources or ACPI device objects) that may
not have been initialized before OSPM starts to enumerate them via
the main ACPI device enumeration.
But after we had reverted back to the expected behavior, a regression
was reported. On that platform, there is no ECDT, but the platform
control methods access EC operation region earlier than Linux expects
causing some ACPI method execution errors. For this reason, we just
go back to old behavior to still probe DSDT EC as the boot EC.
However, that turns out to lead to yet another functional breakage
and in order to work around all of the problems, we skip boot stage
DSDT probe when the ECDT exists so that a later quirk can always use
correct ECDT GPE setting.
Link: http://bugzilla.kernel.org/show_bug.cgi?id=11880
Link: http://bugzilla.kernel.org/show_bug.cgi?id=119261
Link: http://bugzilla.kernel.org/show_bug.cgi?id=195651
Tested-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog & comments massage ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
