| Age | Commit message (Collapse) | Author |
|---|
|
This patch helps to avoid the following build issue:
drivers/gpu/drm/msm/msm_fbdev.c:108:2: error: passing argument 3 of 'msm_gem_get_iova_locked' from incompatible pointer type [-Werror]
msm_gem_get_iova_locked(fbdev->bo, 0, &paddr);
^
In file included from drivers/gpu/drm/msm/msm_fbdev.c:18:0:
drivers/gpu/drm/msm/msm_drv.h:153:5: note: expected 'uint32_t *' but argument is of type 'dma_addr_t *'
int msm_gem_get_iova_locked(struct drm_gem_object *obj, int id,
^
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
The vbus regulator was not getting its name set. This results
in the sysfs entry being empty. The lack of a bcm590xx_regs[]
table entry also upsets Coverity runs. Add the table entry
so the name gets set properly.
Signed-off-by: Graham Williams <graham.williams@linaro.org>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch removes the chip select function. Chip select should instead be
supported using GPIOs, defining the DT entry "cs-gpios", and letting the SPI
core assert/deassert the chip select as it sees fit.
The chip select control inside the controller is buggy. It is supposed to
automatically assert the chip select based on the activity in the controller,
but it is buggy and doesn't work at all. So instead we elect to use GPIOs.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c new drivers from Wolfram Sang:
"Here is a pull request from i2c hoping for the "new driver" rule.
Originally, I wanted to send this request during the merge window, but
code checkers with very recent additions complained, so a few fixups
were needed. So, some more time went by and I merged rc1 to get a
stable base"
So the "new driver" rule is really about drivers that people absolutely
need for the kernel to work on new hardware, which is not so much the
case for i2c. So I considered not pulling this, but eventually
relented.
Just for FYI: the whole (and only) point of "new drivers" is not that
new drivers cannot regress things (they can, and they have - by
triggering badly tested code on machines that never triggered that code
before), but because they can bring to life machines that otherwise
wouldn't be useful at all without the drivers.
So the new driver rule is for essential things that actual consumers
would care about, ie devices like networking or disk drivers that matter
to normal people (not server people - they run old kernels anyway, so
mainlining new drivers is irrelevant for them).
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sun6-p2wi: fix call to snprintf
i2c: rk3x: add NULL entry to the end of_device_id array
i2c: sun6i-p2wi: use proper return value in probe
i2c: sunxi: add P2WI (Push/Pull 2 Wire Interface) controller support
i2c: sunxi: add P2WI DT bindings documentation
i2c: rk3x: add driver for Rockchip RK3xxx SoC I2C adapter
|
|
Pull file locking fixes from Jeff Layton:
"File locking related bugfixes
Nothing too earth-shattering here. A fix for a potential regression
due to a patch in pile #1, and the addition of a memory barrier to
prevent a race condition between break_deleg and generic_add_lease"
* tag 'locks-v3.16-2' of git://git.samba.org/jlayton/linux:
locks: set fl_owner for leases back to current->files
locks: add missing memory barrier in break_deleg
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fixes from Michal Marek:
"There are three fixes for regressions caused by the relative paths
series: deb-pkg, tar-pkg and *docs did not work with O=.
Plus, there is a fix for the linux-headers deb package and a fixed
typo. These are not regression fixes but are safe enough"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: fix a typo in a kbuild document
builddeb: fix missing headers in linux-headers package
Documentation: Fix DocBook build with relative $(srctree)
kbuild: Fix tar-pkg with relative $(objtree)
deb-pkg: Fix for relative paths
|
|
Messages from the modem exceeding 256 bytes cause communication
failure.
The WDM protocol is strictly "read on demand", meaning that we only
poll for unread data after receiving a notification from the modem.
Since we have no way to know how much data the modem has to send,
we must make sure that the buffer we provide is "big enough".
Message truncation does not work. Truncated messages are left unread
until the modem has another message to send. Which often won't
happen until the userspace application has given up waiting for the
final part of the last message, and therefore sends another command.
With a proper CDC WDM function there is a descriptor telling us
which buffer size the modem uses. But with this vendor specific
implementation there is no known way to calculate the exact "big
enough" number. It is an unknown property of the modem firmware.
Experience has shown that 256 is too small. The discussion of
this failure ended up concluding that 512 might be too small as
well. So 1024 seems like a reasonable value for now.
Fixes: 41c47d8cfd68 ("net: huawei_cdc_ncm: Introduce the huawei_cdc_ncm driver")
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-By: Enrico Mioso <mrkiko.rs@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This fixes some lockups in btrfs reported with rc1. It probably has
some performance impact because it is backing off our spinning locks
more often and switching to a blocking lock. I'll be able to nail
that down next week, but for now I want to get the lockups taken care
of.
Otherwise some more stack reduction and assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix wrong error handle when the device is missing or is not writeable
Btrfs: fix deadlock when mounting a degraded fs
Btrfs: use bio_endio_nodec instead of open code
Btrfs: fix NULL pointer crash when running balance and scrub concurrently
btrfs: Skip scrubbing removed chunks to avoid -ENOENT.
Btrfs: fix broken free space cache after the system crashed
Btrfs: make free space cache write out functions more readable
Btrfs: remove unused wait queue in struct extent_buffer
Btrfs: fix deadlocks with trylock on tree nodes
|
|
Pull nfsd bugfixes from Bruce Fields:
"Fixes for a new regression from the xdr encoding rewrite, and a
delegation problem we've had for a while (made somewhat more annoying
by the vfs delegation support added in 3.13)"
* 'for-3.16' of git://linux-nfs.org/~bfields/linux:
NFSD: fix bug for readdir of pseudofs
NFSD: Don't hand out delegations for 30 seconds after recalling them.
|
|
In commit 629c9a8fd0bbdfc6d702526b327470166ec39c6b (drivers: net: cpsw: Add
default vlan for dual emac case also), api cpsw_add_default_vlan() also
changes the port vlan which is required to seperate the ports which results
in the following behavior
In Dual EMAC mode, when both the Etnernet connected is connected to same
switch, it creates a loop in the switch and when a broadcast packet is
received it is forwarded to the other port which stalls the whole switch
and needs a reset/power cycle to the switch to recover. So intead of using
the api, add only the default VLAN entry in dual EMAC case.
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ras3 block on spear320 claims to have 3 interrupts. In fact it has
one and 6 reserved interrupts. Account the 6 reserved to this block so
it has 7 interrupts total. That matches the datasheet and the device
tree entries.
Broken since commit 80515a5a(ARM: SPEAr3xx: shirq: simplify and move
the shared irq multiplexor to DT). Testing is overrated....
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212712.872379208@linutronix.de
Fixes: 80515a5a2e3c ('ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT')
Cc: <stable@vger.kernel.org> # v3.8+
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
David Vrabel says:
====================
xen-netfront: fix resume regressions in 3.16-rc1
The introduction of multi-queue support to xen-netfront in 3.16-rc1,
broke resume/migration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When reconnecting to the backend (after a resume/migration, for example),
a different number of queues may be required (since the guest may have
moved to a different host with different capabilities). During the
reconnection the old queues are torn down and new ones created.
Introduce xennet_create_queues() and xennet_destroy_queues() that fixes
three bugs during the reconnection.
- The old info->queues was leaked.
- The old queue's napi instances were not deleted.
- The new queue's napi instances were left disabled (which meant no
packets could be received).
The xennet_destroy_queues() calls is deferred until the reconnection
instead of the disconnection (in xennet_disconnect_backend()) because
napi_disable() might sleep.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xennet_disconnect_backend() was not correctly iterating over all the
queues.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Mack says:
====================
Handle stuck TX queue bug in AT8030 PHY
These three small patches circument a hardware bug in AT8030 PHYs that
leads to stuck TX FIFO queues when the link goes away while there are
pending patches in der outbound queue. This bug has been confirmed by
the vendor, and their only proposed fix is to apply a hardware reset
every time the link goes down.
v1 -> v2:
* Rename phy device callback from adjust_state to link_change_notify
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The AT8030 will enter a FIFO error mode if a packet is transmitted while
the cable is unplugged. This hardware issue is acknowledged by the
vendor, and the only proposed solution is to conduct a hardware reset
via the external pin each time the link goes down. There is apparantly
no way to fix up the state via the register set.
This patch adds support for reading a 'reset-gpios' property from the DT
node of the PHY. If present, this gpio is used to apply a hardware reset
each time a 'link down' condition is detected. All relevant registers
are read out before, and written back after the reset cycle.
Doing this every time the link goes down might seem like overkill, but
there is unfortunately no way of figuring out whether the PHY is in
such a lock-up state. Hence, this is the only way of reliably fixing up
things.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This removes magic values from two tables and also allows us to match
against specific PHY models at runtime.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a notify callback to inform phy drivers when the core is about to
do its link adjustment. No change for drivers that do not implement
this callback.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_cow called in vlan_reorder_header does not free the skb when it failed,
and vlan_reorder_header returns NULL to reset original skb when it is called
in vlan_untag, lead to a memory leak.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has been broken for quite some time. Just the recent updates made
it compile time broken. Make it depend on BROKEN instead of removing
it right away as we want a proper replacement.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
futex_lock_pi_atomic() is a maze of retry hoops and loops.
Reduce it to simple and understandable states:
First step is to lookup existing waiters (state) in the kernel.
If there is an existing waiter, validate it and attach to it.
If there is no existing waiter, check the user space value
If the TID encoded in the user space value is 0, take over the futex
preserving the owner died bit.
If the TID encoded in the user space value is != 0, lookup the owner
task, validate it and attach to it.
Reduces text size by 128 bytes on x8664.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Kees Cook <kees@outflux.net>
Cc: wad@chromium.org
Cc: Darren Hart <darren@dvhart.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1406131137020.5170@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We want to be a bit more clever in futex_lock_pi_atomic() and separate
the possible states. Split out the code which attaches the first
waiter to the owner into a separate function. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Kees Cook <kees@outflux.net>
Cc: wad@chromium.org
Link: http://lkml.kernel.org/r/20140611204237.271300614@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We want to be a bit more clever in futex_lock_pi_atomic() and separate
the possible states. Split out the waiter verification into a separate
function. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Kees Cook <kees@outflux.net>
Cc: wad@chromium.org
Link: http://lkml.kernel.org/r/20140611204237.180458410@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
No point in open coding the same function again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Kees Cook <kees@outflux.net>
Cc: wad@chromium.org
Link: http://lkml.kernel.org/r/20140611204237.092947239@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The kernel tries to atomically unlock the futex without checking
whether there is kernel state associated to the futex.
So if user space manipulated the user space value, this will leave
kernel internal state around associated to the owner task.
For robustness sake, lookup first whether there are waiters on the
futex. If there are waiters, wake the top priority waiter with all the
proper sanity checks applied.
If there are no waiters, do the atomic release. We do not have to
preserve the waiters bit in this case, because a potentially incoming
waiter is blocked on the hb->lock and will acquire the futex
atomically. We neither have to preserve the owner died bit. The caller
is the owner and it was supposed to cleanup the mess.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <darren@dvhart.com>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Kees Cook <kees@outflux.net>
Cc: wad@chromium.org
Link: http://lkml.kernel.org/r/20140611204237.016987332@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In case the dead lock detector is enabled we follow the lock chain to
the end in rt_mutex_adjust_prio_chain, even if we could stop earlier
due to the priority/waiter constellation.
But once we are no longer the top priority waiter in a certain step
or the task holding the lock has already the same priority then there
is no point in dequeing and enqueing along the lock chain as there is
no change at all.
So stop the queueing at this point.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/20140522031950.280830190@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The conditions under which deadlock detection is conducted are unclear
and undocumented.
Add constants instead of using 0/1 and provide a selection function
which hides the additional debug dependency from the calling code.
Add comments where needed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/20140522031949.947264874@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The deadlock logic is only required for futexes.
Remove the extra arguments for the public functions and also for the
futex specific ones which get always called with deadlock detection
enabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Exit right away, when the removed waiter was not the top priority
waiter on the lock. Get rid of the extra indent level.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Lai Jiangshan <laijs@cn.fujitsu.com>
|
|
Add commentry to document the chain walk and the protection mechanisms
and their scope.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Add a separate local variable for the boost/deboost logic to make the
code more readable. Add comments where appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
|
|
There is no point to keep the task ref across the check for lock
owner. Drop the ref before that, so the protection context is clear.
Found while documenting the chain walk.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Lai Jiangshan <laijs@cn.fujitsu.com>
|
|
The current implementation of try_to_take_rtmutex() is correct, but
requires more than a single brain twist to understand the clever
encoded conditionals.
Untangle it and document the cases proper.
Looks less efficient at the first glance, but actually reduces the
binary code size on x8664 by 80 bytes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Oleg noticed that rtmutex_slowtrylock() has a pointless check for
rt_mutex_owner(lock) != current.
To avoid calling try_to_take_rtmutex() we really want to check whether
the lock has an owner at all or whether the trylock failed because the
owner is NULL, but the RT_MUTEX_HAS_WAITERS bit is set. This covers
the lock is owned by caller situation as well.
We can actually do this check lockless. trylock is taking a chance
whether we take lock->wait_lock to do the check or not.
Add comments to the function while at it.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Lai Jiangshan <laijs@cn.fujitsu.com>
|
|
Reason: Required to add more rtmutex robustness changes on top of
those already in mainline.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"This is larger than usual: the main reason are the ARM symbol lookup
speedups that came in late and were hard to resist.
There's also a kprobes fix and various tooling fixes, plus the minimal
re-enablement of the mmap2 support interface"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/kprobes: Fix build errors and blacklist context_track_user
perf tests: Add test for closing dso objects on EMFILE error
perf tests: Add test for caching dso file descriptors
perf tests: Allow reuse of test_file function
perf tests: Spawn child for each test
perf tools: Add dso__data_* interface descriptons
perf tools: Allow to close dso fd in case of open failure
perf tools: Add file size check and factor dso__data_read_offset
perf tools: Cache dso data file descriptor
perf tools: Add global count of opened dso objects
perf tools: Add global list of opened dso objects
perf tools: Add data_fd into dso object
perf tools: Separate dso data related variables
perf tools: Cache register accesses for unwind processing
perf record: Fix to honor user freq/interval properly
perf timechart: Reflow documentation
perf probe: Improve error messages in --line option
perf probe: Improve an error message of perf probe --vars mode
perf probe: Show error code and description in verbose mode
perf probe: Improve error message for unknown member of data structure
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull rtmutex fixes from Thomas Gleixner:
"Another three patches to make the rtmutex code more robust. That's
the last urgent fallout from the big futex/rtmutex investigation"
* 'locking-urgent-for-linus.patch' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rtmutex: Plug slow unlock race
rtmutex: Detect changes in the pi lock chain
rtmutex: Handle deadlock detection smarter
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"A couple of bug fixes, a debug change for qdio, an update for the
default config, and one small extension.
The watchdog module based on diagnose 0x288 is converted to the
watchdog API and it now works under LPAR as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ccwgroup: use ccwgroup_ungroup wrapper
s390/ccwgroup: fix an uninitialized return code
s390/ccwgroup: obtain extra reference for asynchronous processing
qdio: Keep device-specific dbf entries
s390/compat: correct ucontext layout for high gprs
s390/cio: set device name as early as possible
s390: update default configuration
s390: avoid format strings leaking into names
s390/airq: silence lockdep warning
s390/watchdog: add support for LPAR operation (diag288)
s390/watchdog: use watchdog API
s390/sclp_vt220: Enable ASCII console per default
s390/qdio: replace shift loop by ilog2
s390/cio: silence lockdep warning
s390/uaccess: always load the kernel ASCE after task switch
s390/ap_bus: Make modules parameters visible in sysfs
|
|
Pull UniCore32 bug fixes from Guan Xuetao:
"This includes bugfixes to make unicore32 successfully build under
defconfig, and some changes for allmodconfig (though not finished)"
* tag 'for-linus' of git://github.com/gxt/linux:
unicore32: Remove ARCH_HAS_CPUFREQ config option
UniCore32: Change git tree location information in MAINTAINERS
arch: unicore32: ksyms: export '__cpuc_coherent_kern_range' to avoid compiling failure
arch: unicore32: ksyms: export 'pm_power_off' to avoid compiling failure.
arch: unicore32: ksyms: export additional find_first_*() to avoid compiling failure
arch:unicore32:mm: add devmem_is_allowed() to support STRICT_DEVMEM
unicore32: include: asm: add missing ')' for PAGE_* macros in pgtable.h
arch/unicore32/kernel/setup.c: add generic 'screen_info' to avoid compiling failure
drivers: scsi: mvsas: fix compiling issue by adding 'MVS_' for "enum pci_interrupt_cause"
arch: unicore32: kernel: ksyms: remove 'bswapsi2' and 'muldi3' to avoid compiling failure
arch/unicore32/kernel/ksyms.c: remove 2 export symbols to avoid compiling failure
drivers/rtc/rtc-puv3.c: remove "&dev->" for typo issue MIME-Version: 1.0
drivers/rtc/rtc-puv3.c: use dev_dbg() instead of dev_debug() for typo issue
arch/unicore32/include/asm/io.h: add readl_relaxed() generic definition
arch/unicore32/include/asm/ptrace.h: add generic definition for profile_pc()
arch/unicore32/mm/alignment.c: include "asm/pgtable.h" to avoid compiling error
arch/unicore32/kernel/clock.c: add readl() and writel() for 'PM_' macros
arch/unicore32/kernel/module.c: use __vmalloc_node_range() instead of __vmalloc_area()
arch/unicore32/kernel/ksyms.c: remove several undefined exported symbols
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver fixes from Greg KH:
"Here are 3 patches, one a revert of the UIO patch you objected to in
3.16-rc1 and that no one wanted to defend, a w1 driver bugfix, and a
MAINTAINERS update for the vmware balloon driver.
All of these, except for the MAINTAINERS update which just got added,
have been in linux-next just fine"
* tag 'char-misc-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: add entry for VMware Balloon driver
w1: mxc_w1: Fix incorrect "presence" status
Revert "uio: fix vma io range check in mmap"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a few fixes for staging and iio drivers that resolve issues
reported in 3.16-rc1.
All have been in linux-next just fine"
* tag 'staging-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
imx-drm: parallel-display: Fix DPMS default state.
staging: android: timed_output: fix use after free of dev
staging: comedi: addi_apci_1564: add addi_watchdog dependency
staging: rtl8723au: Reference correct firmwarefiles with MODULE_FIRMWARE()
staging: rtl8723au: Request correct firmware file for A-cut parts
iio: adc: checking for NULL instead of IS_ERR() in probe
iio: adc: at91: signedness bug in at91_adc_get_trigger_value_by_name()
iio: mxs-lradc: fix divider
iio: Fix endianness issue in ak8975_read_axis()
staging/iio: IIO_SIMPLE_DUMMY_BUFFER neds IIO_BUFFER
twl4030-madc: Request processed values in twl4030_get_madc_conversion
staging: iio: tsl2x7x_core: fix proximity treshold
iio: Fix two mpl3115 issues in measurement conversion
iio: hid-sensors: Get feature report from sensor hub after changing power state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial bugfixes from Greg KH:
"Here are some tty / serial driver bugfixes for 3.16-rc2 that resolve
some reported issues. The samsung driver build error itself has been
reported by a bunch of people, sorry about that one. The others are
all tiny and everyone seems to like them in linux-next so far"
* tag 'tty-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty/serial: fix 8250 early console option passing to regular console
tty: Correct INPCK handling
serial: Fix IGNBRK handling
serial: samsung: Fix build error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.16-rc2 that resolve some reported
issues. All of these have been in linux-next for a while with no
problems"
* tag 'usb-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: usbtest: add a timeout for scatter-gather tests
USB: EHCI: avoid BIOS handover on the HASEE E200
usb: fix hub-port pm_runtime_enable() vs runtime pm transitions
usb: quiet peer failure warning, disable poweroff
usb: improve "not suspended yet" message in hub_suspend()
xhci: Fix sleeping with IRQs disabled in xhci_stop_device()
usb: fix ->update_hub_device() vs hdev->maxchild
|
|
Currently in the inkern.c code for IIO framework, the function
of_iio_channel_get_by_name() will return a non-NULL pointer when
it cannot find a channel using of_iio_channel_get() and when it
tries to search for 'io-channel-ranges' property and fails. This
is incorrect behaviour as the function which calls this expects
a NULL pointer for failure. This patch rectifies the issue.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
|
|
We should be returning a negative error code instead of success here.
This would have been detected by GCC, except that the "ret" variable was
initialized with a bogus value to disable GCC's uninitialized variable
warnings. I've cleaned that up, as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
|
|
On exynos mcpm systems the firmware is hardcoded to jump to an address
in SRAM (0x02073000) when secondary CPUs come up. By default the
firmware puts a bunch of code at that location. That code expects the
kernel to fill in a few slots with addresses that it uses to jump back
to the kernel's entry point for secondary CPUs.
Originally (on prerelease hardware) this firmware code contained a
bunch of workarounds to deal with boot ROM bugs. However on all
shipped hardware we simply use this code to redirect to a kernel
function for bringing up the CPUs.
Let's stop relying on the code provided by the bootloader and just
plumb in our own (simple) code jump to the kernel. This has the nice
benefit of fixing problems due to the fact that older bootloaders
(like the one shipped on the Samsung Chromebook 2) might have put
slightly different code into this location.
Once suspend/resume is implemented for systems using exynos-mcpm we'll
need to make sure we reinstall our fixed up code after resume. ...but
that's not anything new since IRAM (and thus the address of the
mcpm_entry_point) is lost across suspend/resume anyway.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
We use regmap regulator ops to enable/disable and check if regulator
is enabled for various SMPS. However, these depend on valid
enable_reg, enable_mask and enable_value in regulator descriptor.
Currently we do not populate these for SMPS other than SMPS10, this
results in spurious results as regmap assumes that the values are
valid and ends up reading register 0x0 RTC:SECONDS_REG on Palmas
variants that do have RTC! To fix this, we update proper parameters
for the descriptor fields.
Further, we want to ensure the behavior consistent with logic
prior to commit dbabd624d4eec50b6, where, once you do a set_mode,
enable/disable ensure the logic remains consistent and configures
Palmas to the configuration that we set with set_mode (since the
configuration register is common). To do this, we can rely on the
regulator core's regulator_register behavior where the regulator
descriptor pointer provided by the regulator driver is stored. (no
reallocation and copy is done). This lets us update the enable_value
post registration, to remain consistent with the mode we configure as
part of set_mode.
Fixes: dbabd624d4eec50b6 ("regulator: palmas: Reemove open coded functions with helper functions")
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch moves the devm_spi_register_master below the initialization of the
runtime_pm. If done in the wrong order, the spi_register_master fails if any
probed slave devices issue SPI transactions.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
last two bits of ADC and limit values are zero and should not be reported
(ad7993, ad7997); compare with read_raw()
event values are 10 (ad7993, ad7997) or 12 bit max., check the range on write
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Stable@vger.kernel.org
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
