| Age | Commit message (Collapse) | Author |
|---|
|
I2C host controller need to be configured properly in order to meet I2C
timings specified in the I2C protocol specification. Some Intel Broxton
based machines do not have this information in the ACPI namespace (or the
boot firmware does not support ACPI at all) so we use build-in device
properties instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds macros to define masks and bits for imx6sx
PCIe registers. This is based on a patch by Richard Zhu.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The ipaq-micro driver uses SET_SYSTEM_SLEEP_PM_OPS() to
remove the reference to its resume function, but does
not use an #ifdef around the definition, so we get
a build warning:
drivers/mfd/ipaq-micro.c:379:12: error: 'micro_resume' defined but not used [-Werror=unused-function]
This adds a __maybe_unused annotation so the compiler knows
it can silently drop it instead of warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The max77686 MFD driver supports both the Maxim 77686 and Maxim 77802
PMICs but only the OF device table contains entries for both devices.
The max77802 entry is missing in the I2C device ID table which isn't
a problem currently since the driver only supports DT but it will be
needed if the driver is changed to be built as a module since the I2C
core always reports a I2C modalias uevent so auto-load will not work.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
When the device is registered via OF, the OF table is used to match the
driver instead of the I2C device ID table but the entries in the latter
are used as aliasses to load the module if the driver was not built-in.
This is because the I2C core always reports an I2C module alias instead
of an OF one but that could change so it is better to always export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The driver's Kconfig symbol is a boolean but nothing prevents the driver
to be built as a module instead of built-in. It is true that most system
integrators will choose the latter but the config should not restrict it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This adds the PWM resources to the STMPE MFD driver, so that
it can properly grab and use them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Regmap config max_register field should contain number of
device last register, however num_reg_defaults_raw field
should be set to register count instead
(usually one register more than max_register).
tps65090 driver had both of these fields set to the same value,
fix this by introducing separate defines for max register
number and total count of registers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
When CONFIG_MFD_SYSCON is disabled, have the function stubs return
ENOTSUPP to indicate the syscon functionality is not available.
There are currently no callers that depend on the ENOSYS return value.
This patchfixes a checkpatch warning:
WARNING: ENOSYS means 'invalid syscall nr' and nothing else
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Regmap config max_register field should contain number of
device last register, however num_reg_defaults_raw field
should be set to register count instead
(usually one register more than max_register).
as3711 driver had both of these fields set to the same value,
fix this by introducing separate defines for max register
number and total count of registers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Regmap config max_register field should contain number of
device last register, however num_reg_defaults_raw field
should be set to register count instead
(usually one register more than max_register).
rc5t583 driver had both of these fields set to the same value,
fix this by introducing separate defines for max register
number and total count of registers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add support for the TPS65086 PMIC GPOs.
TPS65086 has four configurable GPOs that can be used for several
purposes. These are output only.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The platform bus_type .match callback attempts to match the platform device
name with an entry on the .id_table if provided and fallbacks to match with
the driver's name if a table is not provided.
Using a platform device ID to match is more explicit, allows the driver to
support more than one device and also the MODULE_DEVICE_TABLE macro can be
used to export the module aliases information instead of the MODULE_ALIAS.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
volatile lists
Add an updated set of registers listed in the core regmap_range volatile
ranges defined for the DA9063.
These new registers contain bits that cannot be considered under the full
control of software. Under various conditions the hardware will set and/or
automatically clear bit(s) contained in these registers.
When using a cached version of regmap, the volatility of these registers must
be identified otherwise the regmap operations may not ensure the registers
are explicitly altered.
As well as updating the list of volatile registers, this change will fix a
corner case discovered in the DA9063 ONKEY which is used by the DA9063 core.
In the ONKEY case, the CONTROL_B register is now listed as volatile in the
regmap_range because it contains the bit field NONKEY_LOCK. This bit can be
altered by hardware, in which case regmap must be notified of its ability
to be manpiulated outside of software control.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
MT6323 has the INT_CON and INT_STATUS located at a different position.
Make the registers locations configurable.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
volatile lists
Add an updated set of registers listed in the core regmap_range volatile
ranges defined for the DA9062.
These new registers contain bits that cannot be considered under the full
control of software. Under various conditions the hardware will set and/or
automatically clear bit(s) contained in these registers.
When using a cached version of regmap, the volatility of these registers must
be identified otherwise the regmap operations may not ensure the registers
are explicitly altered.
As well as updating the list of volatile registers, this change will fix a
corner case discovered in the DA9063 ONKEY which is used by the DA9062 core.
In the ONKEY case, the CONTROL_B register is now listed as volatile in the
regmap_range because it contains the bit field NONKEY_LOCK. This bit can be
altered by hardware, in which case regmap must be notified of its ability
to be manpiulated outside of software control.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The Active-semi ACT8945A PMIC is a Multi-Function Device, it has
two subdevices:
- Regulator
- Charger
This patch adds documentation for ACT8945A DT bindings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds support for the Active-semi ACT8945A PMIC.
It is a Multi Function Device with the following subdevices:
- Regulator
- Charger
It is interfaced to the host controller using I2C interface,
ACT8945A is a child device of the I2C.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
s/cros_ec_register/cros_ec_query_all
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
MFD_ARIZONA_I2C and MFD_ARIZONA_SPI both select MFD_ARIZONA and all
three of those select MFD_CORE, this makes the selects of MFD_CORE in
MFD_ARIZONA_I2C and MFD_ARIZONA_SPI redundant, so we remove them.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
My automated test is back and now can check defaults against the actual
hardware. This patch updates the defaults array for the differences
detected and removes a couple of completely unused registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
My automated test is back and now can check defaults against the actual
hardware. This patch updates the defaults array for the differences
detected and removes a couple of completely unused registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
My automated test is back and now can check defaults against the actual
hardware. This patch updates the defaults array for the differences
detected and removes a couple of completely unused registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
My automated test is back and now can check defaults against the actual
hardware. This patch updates the defaults array for the differences
detected and removes a couple of completely unused registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The help text had a copy and paste error and refers to I2C in the SPI
section. This patch corrects this typo.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
syscon_regmap_config can be made const if syscon_probe() creates a local
copy on the stack, just like syscon_register() does.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Determine the regmap max_register configuration from the io resource size
and the reg-io-width device tree property.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The prcmu_config_clkout() function ensures that the 'clkout' argument
can only be '0' or '1' using an appropriate BUG_ON(), so the compiler
should know that the div_mask, mask, and bits variables are always
initialized later on. However, it doesn't understand this in gcc-5.2
and produces a false positive warning instead:
drivers/mfd/db8500-prcmu.c: In function 'prcmu_config_clkout':
drivers/mfd/db8500-prcmu.c:762:10: error: 'div_mask' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (val & div_mask) {
^
drivers/mfd/db8500-prcmu.c:769:13: error: 'mask' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if ((val & mask & ~div_mask) != bits) {
^
drivers/mfd/db8500-prcmu.c:757:7: error: 'bits' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Replacing the switch() statement with an equivalent if() lets
gcc figure this out reliably and avoids the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add support for the TPS65912 device. It provides communication
through I2C and contains the following components:
- Regulators
- Load switches
- GPO controller
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The TPS65086 PMIC contains several regulators and a GPO controller.
Add bindings for the TPS65086 PMIC.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"LED core improvements:
- Fix misleading comment after workqueue removal from drivers
- Avoid error message when a USB LED device is unplugged
- Add helpers for calling brightness_set(_blocking)
LED triggers:
- Simplify led_trigger_store by using sysfs_streq()
LED class drivers improvements:
- Improve wording and formatting in a comment: lp3944
- Fix return value check in create_gpio_led(): leds-gpio
- Use GPIOF_OUT_INIT_LOW instead of hardcoded zero: leds-gpio
- Use devm_led_classdev_register(): leds-lm3533, leds-lm3533,
leds-lp8788, leds-wm831x-status, leds-s3c24xx, leds-s3c24xx,
leds-max8997.
New LED class driver:
- Add driver for the ISSI IS31FL32xx family of LED controllers.
Device Tree documentation:
- of: Add vendor prefixes for Integrated Silicon Solutions Inc.
(issi) and Si-En Technology (si-en).
- DT: Add common bindings for Si-En Technology SN3216/18 and
IS31FL32xx family of LED controllers, since they seem to be the
same hardware, just rebranded"
* tag 'leds_for_4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: triggers: simplify led_trigger_store
leds: max8997: Use devm_led_classdev_register
leds: da903x: Use devm_led_classdev_register
leds: s3c24xx: Use devm_led_classdev_register
leds: wm831x-status: Use devm_led_classdev_register
leds: lp8788: Use devm_led_classdev_register
leds: 88pm860x: Use devm_led_classdev_register
leds: Add SN3218 and SN3216 support to the IS31FL32XX driver
of: Add vendor prefix for Si-En Technology
leds: Add driver for the ISSI IS31FL32xx family of LED controllers
DT: leds: Add binding for the ISSI IS31FL32xx family of LED controllers
DT: Add vendor prefix for Integrated Silicon Solutions Inc.
leds: lm3533: Use devm_led_classdev_register
leds: gpio: Use GPIOF_OUT_INIT_LOW instead of hardcoded zero
leds: core: add helpers for calling brightness_set(_blocking)
leds: leds-gpio: Fix return value check in create_gpio_led()
leds: lp3944: improve wording and formatting in a comment
leds: core: avoid error message when a USB LED device is unplugged
leds: core: fix misleading comment after workqueue removal from drivers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Core:
- New sysfs interface to set and read clock offset
- Drivers can now be both I2C and SPI (see pcf2127 and ds3232)
New drivers:
- Alphascale ASM9260
- Epson RX6110SA
- Maxim max20024 and max77620 (in max77686)
- Microchip PIC32
- NXP pcf2129 (in pcf2127)
Subsystem wide cleanups:
- remove IRQF_EARLY_RESUME when unecessary
Drivers:
- ds1307: clock output, temperature sensor and wakeup-source support
- ds1685: actually spin forever in poweroff error path
- ds3232: many cleanups
- ds3234: merged in ds3232
- hym8563: fix invalid year calculation
- max77686: many cleanups
- max77802 merged in max77686
- pcf2123: cleanups and offset support
- pcf85063: cleanups
- pcf8523: propely handle oscillator stop bit
- rv3029: many cleanups, trickle charger and temperature sensor support
- rv8803: convert spin_lock to mutex_lock
- rx8025: many fixes
- vr41xx: restore alarm_irq_enable"
* tag 'rtc-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (86 commits)
rtc: pcf2127: add pcf2129 device id
rtc: pcf2127: add support for spi interface
rtc: pcf2127: convert to use regmap
rtc: rv3029: Add thermometer hwmon support
rtc: rv3029: Add update_bits helper for eeprom access
rtc: ds1685: actually spin forever in poweroff error path
rtc: hym8563: fix invalid year calculation
rtc: ds3232: use rtc->ops_lock to protect alarm operations
rtc: ds3232: fix issue when irq is shared several devices
rtc: ds3232: remove unused UIE code
rtc: ds3232: add register access error checks
rtc: ds3232: fix read on /dev/rtc after RTC_AIE_ON
rtc: merge ds3232 and ds3234
rtc: ds3232: convert to use regmap
rtc: pxa: fix Kconfig indentation
rtc: rv3029: Add device tree property for trickle charger
rtc: rv3029: Add functions for EEPROM access
rtc: rv3029: Add i2c register update-bits helper
rtc: rv3029: Add missing register definitions
rtc: rv3029: Add "rv3029" I2C device id
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- New drivers for NSA320 and LTC2990
- Added support for ADM1278 to adm1275 driver
- Added support for ncpXXxh103 to ntc_thermistor driver
- Renamed vexpress hwmon implementation
- Minor cleanups and improvements
* tag 'hwmon-for-linus-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Create an NSA320 hardware monitoring driver
hwmon: Define binding for the nsa320-hwmon driver
hwmon: (adm1275) Add support for ADM1278
hwmon: (ntc_thermistor) Add support for ncpXXxh103
Doc: hwmon: Fix typo "montoring" in hwmon
ARM: dts: vfxxx: Add iio_hwmon node for ADC temperature channel
ARM: dts: Change iio_hwmon nodes to use hypen in node names
hwmon: (iio_hwmon) Allow the driver to accept hypen in device tree node names
hwmon: Add LTC2990 sensor driver
hwmon: (vexpress) rename vexpress hwmon implementation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been an extremely quiet release for the regulator API, aside
from bugfixes and small enhancements the only thing that really stands
out are the new drivers for Action Semiconductors ACT8945A, HiSilicon
HI665x, and the Maxim MAX20024 and MAX77620"
* tag 'regulator-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (46 commits)
regulator: pwm: Add support to have multiple instance of pwm regulator
regulator: pwm: Fix calculation of voltage-to-duty cycle
regulator: of: Use of_property_read_u32() for reading min/max
regulator: pv88060: fix incorrect clear of event register
regulator: pv88090: fix incorrect clear of event register
regulator: max77620: Add support to configure active-discharge
regulator: core: Add support for active-discharge configuration
regulator: helper: Add helper to configure active-discharge using regmap
regulator: core: Add support for active-discharge configuration
regulator: DT: Add DT property for active-discharge configuration
regulator: act8865: Specify fixed voltage of 3.3V for ACT8600's REG9
regulator: act8865: Rename platform_data field to init_data
regulator: act8865: Remove "static" from local variable
ASoC: cs4271: add regulator consumer support
regulator: max77620: Remove duplicate module alias
regulator: max77620: Eliminate duplicate code
regulator: max77620: Remove unused fields
regulator: core: fix crash in error path of regulator_register
regulator: core: Request GPIO before creating sysfs entries
regulator: gpio: don't print error on EPROBE_DEFER
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a very busy release for regmap, not just in cleaning up
the mess we got ourselves into with the endianness handling but also
in other areas too:
- Fixes for the endianness handling so that we now explicitly default
to little endian (the code used to do this by accident). This
fixes handling of explictly specified endianness on big endian
systems.
- Optimisation of the implementation of register striding.
- A refectoring of the _update_bits() code to reduce duplication.
- Fixes and enhancements for the interrupt implementation which make
it easier to use in a wider range of systems"
* tag 'regmap-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (28 commits)
regmap: irq: add devm apis for regmap_{add,del}_irq_chip
regmap: replace regmap_write_bits()
regmap: irq: Enable irq retriggering for nested irqs
regmap: add regmap_fields_force_xxx() macros
regmap: add regmap_field_force_xxx() macros
regmap: merge regmap_fields_update_bits() into macro
regmap: merge regmap_fields_write() into macro
regmap: add regmap_fields_update_bits_base()
regmap: merge regmap_field_update_bits() into macro
regmap: merge regmap_field_write() into macro
regmap: add regmap_field_update_bits_base()
regmap: merge regmap_update_bits_check_async() into macro
regmap: merge regmap_update_bits_check() into macro
regmap: merge regmap_update_bits_async() into macro
regmap: merge regmap_update_bits() into macro
regmap: add regmap_update_bits_base()
regcache: flat: Introduce register strider order
regcache: Introduce the index parsing API by stride order
regmap: core: Introduce register stride order
regmap: irq: add devm apis for regmap_{add,del}_irq_chip
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Not the biggest set of changes for SPI but a bit of a pickup in
activity on the core:
- Support for memory mapped read from flash devices via a SPI
controller.
- The beginnings of a message rewriting framework in the core which
should in time allow us to support transforming messages to work
around the limits of controllers or optimise the performance for
controllers transparently to calling drivers.
- Updates to the PXA2xx, the main functional change being to improve
the ACPI support.
- A new driver for the Analog Devices AXI SPI engine"
* tag 'spi-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (66 commits)
spi: Add gfp parameter to kernel-doc to fix build warning
spi: Fix htmldocs build error due struct spi_replaced_transfers
spi: rockchip: covert rsd_nsecs to u32 type
spi: rockchip: header file cleanup
spi: xilinx: Add devicetree binding for spi-xilinx
spi: respect the maximum segment size of DMA device
spi: rockchip: check requesting dma channel with EPROBE_DEFER
spi: rockchip: migrate to dmaengine_terminate_async
spi: rockchip: check return value of dmaengine_prep_slave_sg
spi: core: Fix deadlock when sending messages
spi/rockchip: fix endian mode for 16-bit transfers
spi/rockchip: Make sure spi clk is on in rockchip_spi_set_cs
spi: pxa2xx: Use newer more explicit DMAengine terminate API
spi: pxa2xx: Add support for Intel Broxton B-Step
spi: lp-8841: return correct error code from probe
spi: imx: drop bogus tests for rx/tx bufs in DMA transfer
spi: imx: set MX51_ECSPI_CTRL_SMC bit in setup function
spi: imx: make some register defines simpler
spi: imx: remove unnecessary bit clearing in mx51_ecspi_config
spi: imx: add support for all SPI word width for DMA
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"An almost purely driver related set of changes with no major changes
to the framework, only one patch adding an unlocked version of the
pinctrl_find_gpio_range_from_pin() library call.
New drivers:
- ST Microelectronics STM32 MCU support: this is a non-MMU low-end
platform for IoT things (etc).
- Microchip PIC32 MCU support: same story as for STM32.
New subdrivers:
- Allwinner SunXi H3 R_PIO controller support.
- Qualcomm IPQ4019 support.
- MediaTek MT2701 and MT7623.
- Allwinner A64
Non-critical fixes:
- gpio_disable_free() for the Vybrid.
- pinctrl single: use a separate lockdep class.
Misc:
- Substantial cleanups and rewrites for the Super-H PFC driver and
subdrivers.
- Various fixes and cleanups, especially Paul Gortmakers work to make
nonmodular drivers nonmodular"
* tag 'pinctrl-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
pinctrl: single: Use a separate lockdep class
drivers: pinctrl: add driver for Allwinner A64 SoC
pinctrl: Broadcom Northstar2 pinctrl device tree bindings
pinctrl: amlogic: Make driver independent from two-domain configuration
pinctrl: amlogic: Separate some pin functions for Meson8 / Meson8b
pinctrl: at91: use __maybe_unused to hide pm functions
pinctrl: sh-pfc: core: don't open code of_device_get_match_data()
pinctrl: uniphier: rename CONFIG options and file names
pinctrl: sunxi: make A80 explicitly non-modular
pinctrl: stm32: make explicitly non-modular
pinctrl: sh-pfc: make explicitly non-modular
pinctrl: meson: make explicitly non-modular
pinctrl: pinctrl-mt6397 driver explicitly non-modular
pinctrl: sunxi: does not need module.h
pinctrl: pxa2xx: export symbols
pinctrl: sunxi: Change mux setting on PI irq pins
pinctrl: sunxi: Remove non existing irq's
pinctrl: imx: attach iomuxc device to gpr syscon
pinctrl-bcm2835: Fix cut-and-paste error in "pull" parsing
pinctrl: lpc1850-scu: document nxp,gpio-pin-interrupt
...
|
|
gcc-6.0 notices that the use of the property_entry in this file that
was recently introduced cannot work right, as we initialize the wrong
field:
raumfeld.c:387:3: error: the address of 'raumfeld_rotary_encoder_steps' will always evaluate as 'true' [-Werror=address]
DEV_PROP_U32, 1, &raumfeld_rotary_encoder_steps, },
^~~~~~~~~~~~
raumfeld.c:389:3: error: the address of 'raumfeld_rotary_encoder_axis' will always evaluate as 'true' [-Werror=address]
DEV_PROP_U32, 1, &raumfeld_rotary_encoder_axis, },
^~~~~~~~~~~~
raumfeld.c:391:3: error: the address of 'raumfeld_rotary_encoder_relative_axis' will always evaluate as 'true' [-Werror=address]
DEV_PROP_U32, 1, &raumfeld_rotary_encoder_relative_axis, },
^~~~~~~~~~~~
The problem appears to stem from relying on an old definition of
'struct property', but it has changed several times since the code
could have last been correct.
This changes the code to use the PROPERTY_ENTRY_INTEGER() macro instead,
which works fine for the current definition and is a safer way of doing
the initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: a9e340dce3c3 ("Input: rotary_encoder - move away from platform data structure")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Since including linux/string.h will now do the right thing remove the
conditional check.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use the standard pr_xxx() log macros directly for log prints instead of
the AUTOFS_XXX() macros.
Signed-off-by: Ian Kent <ikent@redhat.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Common kernel coding practice is to include the newline of log prints
within the log text rather than hidden away in a macro.
To avoid introducing inconsistencies as changes are made change the log
macros to not include the newline.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use the pr_*() print in AUTOFS_*() macros instead of printks and include
the module name in log message macros. Also use the AUTOFS_*() macros
everywhere instead of raw printks.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix some white space format errors.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The return from an ioctl if an invalid ioctl is passed in should be
EINVAL not ENOSYS.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The need for this is questionable but checkpatch.pl complains about the
line length and it's a straightfoward change.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Refactor autofs4_get_set_timeout() to eliminate coding style error.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Try and make the coding style completely consistent throughtout the
autofs module and inline with kernel coding style recommendations.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
