| Age | Commit message (Collapse) | Author |
|---|
|
The Freescale MPC8610 driver was defining two SOC card (snd_soc_card)
structures, partially initializing each one, but registering only one of
them with ASoC.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
There are situations when nodes vanish from the bus and come back
quickly thereafter:
- When certain bus-powered hubs are plugged in,
- when certain devices are plugged into 6-port hubs,
- when certain disk enclosures are switched from self-power to bus
power or vice versa and break the daisy chain during the transition,
- when the user plugs a cable out and quickly plugs it back in, e.g.
to reorder a daisy chain (works on Mac OS X if done quickly enough),
- when certain hubs temporarily malfunction during high bus traffic.
Until now, firewire-core reported affected nodes as lost to the
highlevel drivers (firewire-sbp2 and userspace drivers). We now delay
the destruction of device representations until after at least two
seconds after the last bus reset. If a "new" device is detected in this
period whose bus information block and root directory header match that
of a device which is pending for deletion, we resurrect that device and
send update calls to highlevel drivers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Noticed by Jarod Wilson: The bus manager work was unnecessarily delayed
each time the bus generation counter rolled over.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
|
|
The whole topology code only works if the old and new topologies which
are compared come from immediately successive self ID complete events.
If there happened bus resets without self ID complete events in the
meantime, or self ID complete events with invalid selfIDs, the topology
comparison could identify nodes wrongly, or more likely just corrupt
kernel memory or panic right away.
We now discard all nodes of the old topology and treat all current nodes
as new ones if the current self ID generation is not the previous one
plus 1.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
|
|
Update the 40x defconfigs for 2.6.29-rc2
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
This reverts commit fc8c7dc1b29560c016a67a34ccff32a712b5aa86.
As indicated by Jiri Klimes, this won't work. These numbers are
not only used the size validation, they are also used to locate
attributes sitting after the message.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GregKH asked to fix UBI which has fake device release method. Indeed,
we have to free UBI device description object from the release method,
because otherwise we'll oops is someone opens a UBI device sysfs file,
then the device is removed, and he reads the file. With this fix, he
will get -ENODEV instead of an oops.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
The localbus node flash had a minor typo for a read-only property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
When trying to unlink a file with indirect blocks on a filesystem
without a journal, the "circular indirect block" sanity test was
getting falsely triggered.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
Convert the Warp platform to use the newly merged NDFC driver
- warp.dts changed to work with ndfc
- warp-nand.c no longer needed
- removed obsolete rev A support from cuboot-warp.c
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Added additional information for type and compatibility strings and
interrupt information to the SDRAM0 memory-controller device tree
nodes for AMCC PowerPC 405EX[r]-based boards to facilitate binding
with the new "ibm,sdram-4xx-ddr2" EDAC memory controller adapter driver.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Impact: fix to allow some archs to use the ring buffer
Commits in the ring buffer are checked by pointer arithmetic.
If the calculation is incorrect, then the commits will never take
place and the buffer will simply fill up and report an error.
Each page in the ring buffer has a small header:
struct buffer_data_page {
u64 time_stamp;
local_t commit;
unsigned char data[];
};
Unfortuntely, some of the calculations used sizeof(struct buffer_data_page)
to know the size of the header. But this is incorrect on some archs,
where sizeof(struct buffer_data_page) does not equal
offsetof(struct buffer_data_page, data), and on those archs, the commits
are never processed.
This patch replaces the sizeof with offsetof.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
If we do a userspace access from kernel mode, and get a
data access exception, we need to check the exception
table just like a normal fault does.
The spitfire DAX handler was doing this, but such logic
was missing from the sun4v DAX code.
Reported-by: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sparc64 needs sign-extended function parameters. We have to enable
the system call wrappers.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Roel Kluin reported a bug in two error paths where skbs were wrongly
being freed using kfree(). He provided a fix where it was replaced to
kfree_skb(), as it should be.
However, in i2400mu_rx(), the error path was missing returning an
indication of the failure. Changed to reset rx_skb to NULL and return
it to the caller, i2400mu_rxd(). It will be treated as a transient
error and just ignore the packet.
Depending on the buffering conditions inside the device, the data
packet might be dropped or the device will signal the host again for
data-ready-to-read and the host will retry.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Contrary to what the docs say, the 'extended interrupt cause' bit in
the interrupt cause register (bit 1) appears to not be maskable on at
least some of the mv643xx_eth platforms, making writing zeroes to the
interrupt mask register but not the extended interrupt mask register
insufficient to stop interrupts from occuring. Therefore, also write
zeroes to the extended interrupt mask register when shutting down the
port.
This fixes the interrupt storm seen on the Pegasos board when shutting
down the interface.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 66e63ffbc04706568d8789cbb00eaa8ddbcae648 ("mv643xx_eth:
implement ->set_rx_mode()") cleaned up mv643xx_eth's multicast filter
programming, but broke it as well.
The non-special multicast filter table (for multicast addresses that
are not of the form 01:00:5e:00:00:xx) consists of 256 hash table
buckets organised as 64 32-bit words, where the 'accept' bits are
in the LSB of each byte, so in bits 24 16 8 0 of each 32-bit word.
The old code got this right, but the referenced commit broke this by
using bits 3 2 1 0 instead. This commit fixes this up.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit cd4ccf76bfd2c36d351e68be7e6a597268f98a1a.
On the Pegasos board, we can't do DMA burst that are longer than
one cache line. For now, go back to using 32 byte DMA bursts for
all mv643xx_eth platforms -- we can switch the ARM-based platforms
back to doing long 128 byte bursts in the next development cycle.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reported-by: Alan Curry <pacman@kosh.dhis.org>
Reported-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The trick in socket splicing where we try to convert the skb->data
into a page based reference using virt_to_page() does not work so
well.
The idea is to pass the virt_to_page() reference via the pipe
buffer, and refcount the buffer using a SKB reference.
But if we are splicing from a socket to a socket (via sendpage)
this doesn't work.
The from side processing will grab the page (and SKB) references.
The sendpage() calls will grab page references only, return, and
then the from side processing completes and drops the SKB ref.
The page based reference to skb->data is not enough to keep the
kmalloc() buffer backing it from being reused. Yet, that is
all that the socket send side has at this point.
This leads to data corruption if the skb->data buffer is reused
by SLAB before the send side socket actually gets the TX packet
out to the device.
The fix employed here is to simply allocate a page and copy the
skb->data bytes into that page.
This will hurt performance, but there is no clear way to fix this
properly without a copy at the present time, and it is important
to get rid of the data corruption.
With fixes from Herbert Xu.
Tested-by: Willy Tarreau <w@1wt.eu>
Foreseen-by: Changli Gao <xiaosuo@gmail.com>
Diagnosed-by: Willy Tarreau <w@1wt.eu>
Reported-by: Willy Tarreau <w@1wt.eu>
Fixed-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch modifies how the tg3 driver handles device firmware.
The patch starts by consolidating David Woodhouse's earlier patch under
the same name. Specifically, the patch moves the request_firmware call
into a separate tg3_request_firmware() function and calls that function
from tg3_open() rather than tg3_init_one().
The patch then goes on to limit the number of devices that will make
request_firmware calls. The original firmware patch unnecessarily
requested TSO firmware for devices that did not need it. This patch
reduces the set of devices making TSO firmware patches to approximately
the following device set : 5703, 5704, and 5705.
Finally, the patch reduces the effects of a request_firmware() failure.
For those devices that are requesting TSO firmware, the driver will turn
off the TSO capability. If TSO firmware becomes available at a later
time, the device can be closed and then opened again to reacquire the
TSO capability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_carrier_off() is sufficient to stop Tx into the driver. Stopping the Tx
queues is redundant and unnecessary. By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register VLAN ID 0 so that frames with VLAN ID 0 are received and get
their tag stripped when ixgbe is not in DCB mode. VLAN ID 0 means
that the frame is 'priority tagged' only - it is not a VLAN, but the
priority value is the tag in valid. The functions
ixgbe_vlan_rx_register() and ixgbe_vlan_rx_kill_vid() were moved up a
couple functions to correct compiling issues with this change.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The is an issue where setting Relaxed Ordering (RO) bit
(in a PCI-E write transaction) on 82598 causing the chipset
to drop DCA hints. This patch forces RO not to be set for
descriptors as well as payload. This will only be in effect
while DCA is enabled and no performance difference was
noticed in testing.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I'm trying to track down why people're hitting the checksum warning
in skb_gso_segment. As the problem seems to be hitting lots of
people and I can't reproduce it or locate the bug, here is a patch
to print out more details which hopefully should help us to track
this down.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the assigned value is being overwritten shortly after, it can be
dropped and so the whole variable definition moved to the start of the
function.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is copy and paste from the original driver. As skb_reserve() is
also called within korina_alloc_ring() when initially allocating the
receive descriptors, the same should be done when allocating new space
after passing an skb to upper layers.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the last loop iteration, i has the value RC32434_NUM_RDS and
therefore leads to an index overflow when used afterwards to address the
last element. This is yet another another bug introduced when rewriting
parts of the driver for upstream preparation, as the original driver
used 'RC32434_NUM_RDS - 1' instead.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The lro manager's frag_align_pad setting was missing,
leading to misaligned access to the skb passed up
to the stack.
Tested-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rare cases when an underrun occur, all macb buffers where consumed
and the netif_queue was stopped infinitely. This happens then the TGO
(transfer ongoing) bit in the TSR is set (and UND). It seems like
clening up after the underrun makes the driver and the macb hardware
end up in an inconsistent state. The result of this is that in the
following calls to macb_tx no TX buffers are released -> the
netif_queue was stopped, and never woken up again.
The solution is to disable the transmitter, if TGO is set, before
clening up after the underrun, and re-enable the transmitter when the
cleaning up is done.
Signed-off-by: Richard Röjfors <richard.rojfors@endian.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updating the version and the year of updated files
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make sure no swapping are made by the compiler, changed HAS_WORK to inline
functions and added all the necessary barriers
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Driver supports the 57711 and 57711E as well but the description was out of
date
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the default PHY version (0x4321) is read - the PHY FW load failed
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
10M/100M autoneg was not establishing link.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting loopback requires time to take effect
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HW should be configured so fast toggling between 1G and 10G will not be
missed. Make sure that the HW is re-configured in full
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the page size is > 8KB this violation happens
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't dump eeprom when bnx2x adapter is down. Running ethtool -e causes an eeh
without it when the device is down
Signed-off-by: Paul Larson <pl@linux.vnet.ibm.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Has a negative side effect when sending MAC update with no content (as done in
the self-test)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The lock was release too soon. Make sure the HW is marked as locked until the
boot driver was unloaded from FW perspective
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Failures in the probe not handled correctly - separate the flow to handle
different failures
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Error check could result with not freeing the IRQ
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Impact: fix crash with memory hotplug enabled
kernel_physical_mapping_init() is called during memory hotplug
so it does not belong in the init section.
If the kernel is built with CONFIG_DEBUG_SECTION_MISMATCH=y on
the make command line, arch/x86/mm/init_64.c is compiled with
the -fno-inline-functions-called-once gcc option defeating
inlining of kernel_physical_mapping_init() within init_memory_mapping().
When kernel_physical_mapping_init() is not inlined it is placed
in the .init.text section according to the __init in it's current
declaration. A later call to kernel_physical_mapping_init() during
a memory hotplug operation encounters an int3 trap because the
.init.text section memory has been freed.
This patch eliminates the crash caused by the int3 trap by moving the
non-inlined kernel_physical_mapping_init() from .init.text to .meminit.text.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
-tip testing found this crash:
> [ 35.258515] calling acpi_cpufreq_init+0x0/0x127 @ 1
> [ 35.264127] BUG: unable to handle kernel NULL pointer dereference at (null)
> [ 35.267554] IP: [<ffffffff80478092>] __bitmap_intersects+0x48/0x73
> [ 35.267554] PGD 0
> [ 35.267554] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
arch/x86/kernel/cpu/cpufreq/acpi-cpufreq.c is still broken: there's no
allocation of the variable mask, so we pass in an uninitialized cmd.mask
field to drv_read(), which then passes it to the scheduler which then
crashes ...
Switch it over to the much simpler constant-cpumask-pointers approach.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
i.MX3x SoCs contain an Image Processing Unit, consisting of a Control
Module (CM), Display Interface (DI), Synchronous Display Controller (SDC),
Asynchronous Display Controller (ADC), Image Converter (IC), Post-Filter
(PF), Camera Sensor Interface (CSI), and an Image DMA Controller (IDMAC).
CM contains, among other blocks, an Interrupt Generator (IG) and a Clock
and Reset Control Unit (CRCU). This driver serves IDMAC and IG. They are
supported over dmaengine and irq-chip APIs respectively.
IDMAC is a specialised DMA controller, its DMA channels cannot be used for
general-purpose operations, even though it might be possible to configure
a memory-to-memory channel for memcpy operation. This driver will not work
with generic dmaengine clients, clients, wishing to use it must use
respective wrapper structures, they also must specify which channels they
require, as channels are hard-wired to specific IPU functions.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
To complete the DMA_CTRL_ACK handling API add a async_tx_clear_ack() macro.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
