| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fix from Thomas Bogendoerfer:
"Fix for syscall_get_nr() to make it work even if tracing is disabled"
* tag 'mips-fixes_6.9_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: scall: Save thread_info.syscall unconditionally on entry
|
|
Pull drm fixes from Dave Airlie:
"Looks like everyone woke up after holidays, this weeks pull has a
bunch of stuff all over, 2 weeks worth of amdgpu is a lot of it, then
i915/xe have a few, a bunch of msm fixes, then some scattered driver
fixes.
I expect things will settle down for rc5.
client:
- Protect connector modes with mode_config mutex
ast:
- Fix soft lockup
host1x:
- Do not setup DMA for virtual addresses
ivpu:
- Fix deadlock in context_xa
- PCI fixes
- Fixes to error handling
nouveau:
- gsp: Fix OOB access
- Fix casting
panfrost:
- Fix error path in MMU code
qxl:
- Revert "drm/qxl: simplify qxl_fence_wait"
vmwgfx:
- Enable DMA for SEV mappings
i915:
- Couple CDCLK programming fixes
- HDCP related fix
- 4 Bigjoiner related fixes
- Fix for a circular locking around GuC on reset+wedged case
xe:
- Fix double display mutex initializations
- Fix u32 -> u64 implicit conversions
- Fix RING_CONTEXT_CONTROL not marked as masked
msm:
- DP refcount leak fix on disconnect
- Add missing newlines to prints in msm_fb and msm_kms
- fix dpu debugfs entry permissions
- Fix the interface table for the catalog of X1E80100
- fix irq message printing
- Bindings fix to add DP node as child of mdss for mdss node
- Minor typo fix in DP driver API which handles port status change
- fix CHRASHDUMP_READ()
- fix HHB (highest bank bit) for a619 to fix UBWC corruption
amdgpu:
- GPU reset fixes
- Fix some confusing logging
- UMSCH fix
- Aborted suspend fix
- DCN 3.5 fixes
- S4 fix
- MES logging fixes
- SMU 14 fixes
- SDMA 4.4.2 fix
- KASAN fix
- SMU 13.0.10 fix
- VCN partition fix
- GFX11 fixes
- DWB fixes
- Plane handling fix
- FAMS fix
- DCN 3.1.6 fix
- VSC SDP fixes
- OLED panel fix
- GFX 11.5 fix
amdkfd:
- GPU reset fixes
- fix ioctl integer overflow"
* tag 'drm-fixes-2024-04-12' of https://gitlab.freedesktop.org/drm/kernel: (65 commits)
amdkfd: use calloc instead of kzalloc to avoid integer overflow
drm/xe: Label RING_CONTEXT_CONTROL as masked
drm/xe/xe_migrate: Cast to output precision before multiplying operands
drm/xe/hwmon: Cast result to output precision on left shift of operand
drm/xe/display: Fix double mutex initialization
drm/amdgpu: differentiate external rev id for gfx 11.5.0
drm/amd/display: Adjust dprefclk by down spread percentage.
drm/amd/display: Set VSC SDP Colorimetry same way for MST and SST
drm/amd/display: Program VSC SDP colorimetry for all DP sinks >= 1.4
drm/amd/display: fix disable otg wa logic in DCN316
drm/amd/display: Do not recursively call manual trigger programming
drm/amd/display: always reset ODM mode in context when adding first plane
drm/amdgpu: fix incorrect number of active RBs for gfx11
drm/amd/display: Return max resolution supported by DWB
amd/amdkfd: sync all devices to wait all processes being evicted
drm/amdgpu: clear set_q_mode_offs when VM changed
drm/amdgpu: Fix VCN allocation in CPX partition
drm/amd/pm: fix the high voltage issue after unload
drm/amd/display: Skip on writeback when it's not applicable
drm/amdgpu: implement IRQ_STATE_ENABLE for SDMA v4.4.2
...
|
|
As Mark explains ksft_min_kernel_version() can't be compiled with nolibc,
it doesn't implement uname().
Fixes: 6d029c25b71f ("selftests/timers/posix_timers: Reimplement check_timer_distribution()")
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240412123536.GA32444@redhat.com
Closes: https://lore.kernel.org/all/f0523b3a-ea08-4615-b0fb-5b504a2d39df@sirena.org.uk/
|
|
While monitoring the throttle time of IO from iocost, it's found that
such time is always zero after the io_schedule() from ioc_rqos_throttle,
for example, with the following debug patch:
+ printk("%s-%d: %s enter %llu\n", current->comm, current->pid, __func__, blk_time_get_ns());
while (true) {
set_current_state(TASK_UNINTERRUPTIBLE);
if (wait.committed)
break;
io_schedule();
}
+ printk("%s-%d: %s exit %llu\n", current->comm, current->pid, __func__, blk_time_get_ns());
It can be observerd that blk_time_get_ns() always return the same time:
[ 1068.096579] fio-1268: ioc_rqos_throttle enter 1067901962288
[ 1068.272587] fio-1268: ioc_rqos_throttle exit 1067901962288
[ 1068.274389] fio-1268: ioc_rqos_throttle enter 1067901962288
[ 1068.472690] fio-1268: ioc_rqos_throttle exit 1067901962288
[ 1068.474485] fio-1268: ioc_rqos_throttle enter 1067901962288
[ 1068.672656] fio-1268: ioc_rqos_throttle exit 1067901962288
[ 1068.674451] fio-1268: ioc_rqos_throttle enter 1067901962288
[ 1068.872655] fio-1268: ioc_rqos_throttle exit 1067901962288
And I think the root cause is that 'PF_BLOCK_TS' is always cleared
by blk_flush_plug() before scheduel(), hence blk_plug_invalidate_ts()
will never be called:
blk_time_get_ns
plug->cur_ktime = ktime_get_ns();
current->flags |= PF_BLOCK_TS;
io_schedule:
io_schedule_prepare
blk_flush_plug
__blk_flush_plug
/* the flag is cleared, while time is not */
current->flags &= ~PF_BLOCK_TS;
schedule
sched_update_worker
/* the flag is not set, hence plug->cur_ktime is not cleared */
if (tsk->flags & PF_BLOCK_TS)
blk_plug_invalidate_ts()
blk_time_get_ns
/* got the time stashed before schedule */
return plug->cur_ktime;
Fix the problem by clearing cached time in __blk_flush_plug().
Fixes: 06b23f92af87 ("block: update cached timestamp post schedule/preemption")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240411032349.3051233-2-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Building with clang results in the following warning:
posix_timers.c:69:6: warning: absolute value function 'abs' given an
argument of type 'long long' but has parameter of type 'int' which may
cause truncation of value [-Wabsolute-value]
if (abs(diff - DELAY * USECS_PER_SEC) > USECS_PER_SEC / 2) {
^
So switch to using llabs() instead.
Fixes: 0bc4b0cf1570 ("selftests: add basic posix timers selftests")
Signed-off-by: John Stultz <jstultz@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410232637.4135564-3-jstultz@google.com
|
|
__noreturn
After commit 6d029c25b71f ("selftests/timers/posix_timers: Reimplement
check_timer_distribution()"), clang warns:
tools/testing/selftests/timers/../kselftest.h:398:6: warning: variable 'major' is used uninitialized whenever '||' condition is true [-Wsometimes-uninitialized]
398 | if (uname(&info) || sscanf(info.release, "%u.%u.", &major, &minor) != 2)
| ^~~~~~~~~~~~
tools/testing/selftests/timers/../kselftest.h:401:9: note: uninitialized use occurs here
401 | return major > min_major || (major == min_major && minor >= min_minor);
| ^~~~~
tools/testing/selftests/timers/../kselftest.h:398:6: note: remove the '||' if its condition is always false
398 | if (uname(&info) || sscanf(info.release, "%u.%u.", &major, &minor) != 2)
| ^~~~~~~~~~~~~~~
tools/testing/selftests/timers/../kselftest.h:395:20: note: initialize the variable 'major' to silence this warning
395 | unsigned int major, minor;
| ^
| = 0
This is a false positive because if uname() fails, ksft_exit_fail_msg()
will be called, which unconditionally calls exit(), a noreturn function.
However, clang does not know that ksft_exit_fail_msg() will call exit() at
the point in the pipeline that the warning is emitted because inlining has
not occurred, so it assumes control flow will resume normally after
ksft_exit_fail_msg() is called.
Make it clear to clang that all of the functions that call exit()
unconditionally in kselftest.h are noreturn transitively by marking them
explicitly with '__attribute__((__noreturn__))', which clears up the
warning above and any future warnings that may appear for the same reason.
Fixes: 6d029c25b71f ("selftests/timers/posix_timers: Reimplement check_timer_distribution()")
Reported-by: John Stultz <jstultz@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240411-mark-kselftest-exit-funcs-noreturn-v1-1-b027c948f586@kernel.org
Closes: https://lore.kernel.org/all/20240410232637.4135564-2-jstultz@google.com/
|
|
After commit 6d029c25b71f ("selftests/timers/posix_timers: Reimplement
check_timer_distribution()") the following warning occurs when building
with an older gcc:
posix_timers.c:250:2: warning: format not a string literal and no format arguments [-Wformat-security]
250 | ksft_print_msg(errmsg);
| ^~~~~~~~~~~~~~
Fix this up by changing it to ksft_print_msg("%s", errmsg)
Fixes: 6d029c25b71f ("selftests/timers/posix_timers: Reimplement check_timer_distribution()")
Signed-off-by: John Stultz <jstultz@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Justin Stitt <justinstitt@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410232637.4135564-1-jstultz@google.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
netfilter pull request 24-04-11
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
Patches #1 and #2 add missing rcu read side lock when iterating over
expression and object type list which could race with module removal.
Patch #3 prevents promisc packet from visiting the bridge/input hook
to amend a recent fix to address conntrack confirmation race
in br_netfilter and nf_conntrack_bridge.
Patch #4 adds and uses iterate decorator type to fetch the current
pipapo set backend datastructure view when netlink dumps the
set elements.
Patch #5 fixes removal of duplicate elements in the pipapo set backend.
Patch #6 flowtable validates pppoe header before accessing it.
Patch #7 fixes flowtable datapath for pppoe packets, otherwise lookup
fails and pppoe packets follow classic path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Louis Peens says:
====================
nfp: series of minor driver improvements
This short series bundles now only includes a small update to add a
board part number to devlink. Previously some dim patches also formed
part of this series, these were dropped in v5.
Patch1: Add new define for devlink string "board.part_number"
Patch2: Make use of this field in the nfp driver
Changes since V4:
- Dropped the dim patches, as there is a more significant rework in
progress to make it more flexible, as mentioned in the V4 review:
https://lore.kernel.org/all/1712547870-112976-2-git-send-email-hengqi@linux.alibaba.com/
- Updated the devlink description of 'board.part_number'
Changes since V3:
- Fixed: Documentation/networking/devlink/devlink-info.rst:150:
WARNING: Title underline too short.
Changes since V2:
- After some discussion on the previous series it was agreed that only
the "board.part_number" field makes sense in the common code. The
"board.model" field which was moved to devlink common code in V1 is
now kept in the driver. The field is specific to the nfp driver,
exposing the codename of the board.
- In summary, add "board.part_number" to devlink, and populate it
in the the nfp driver.
Changes since V1:
- Move nfp local defines to devlink common code as it is quite generic.
- Add new 'dim' profile instead of using driver local overrides, as this
allows use of the 'dim' helpers.
- This expanded 2 patches to 4, as the common code changes are split
into seperate patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer NIC will introduce a new part number, now add it
into devlink device info.
This patch also updates the information of "board.id" in
nfp.rst to match the devlink-info.rst.
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add definition and documentation for the new generic
info "board.part_number".
The new one is for part number specific use, and board.id
is modified to match the documentation in devlink-info.
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use consistent log severity (pr_warn) to log all messages in SNP
enable path.
Suggested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20240410101643.32309-1-vasant.hegde@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Commit 1a75cc710b95 ("iommu/vt-d: Use rbtree to track iommu probed
devices") adds all devices probed by the iommu driver in a rbtree
indexed by the source ID of each device. It assumes that each device
has a unique source ID. This assumption is incorrect and the VT-d
spec doesn't state this requirement either.
The reason for using a rbtree to track devices is to look up the device
with PCI bus and devfunc in the paths of handling ATS invalidation time
out error and the PRI I/O page faults. Both are PCI ATS feature related.
Only track the devices that have PCI ATS capabilities in the rbtree to
avoid unnecessary WARN_ON in the iommu probe path. Otherwise, on some
platforms below kernel splat will be displayed and the iommu probe results
in failure.
WARNING: CPU: 3 PID: 166 at drivers/iommu/intel/iommu.c:158 intel_iommu_probe_device+0x319/0xd90
Call Trace:
<TASK>
? __warn+0x7e/0x180
? intel_iommu_probe_device+0x319/0xd90
? report_bug+0x1f8/0x200
? handle_bug+0x3c/0x70
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? intel_iommu_probe_device+0x319/0xd90
? debug_mutex_init+0x37/0x50
__iommu_probe_device+0xf2/0x4f0
iommu_probe_device+0x22/0x70
iommu_bus_notifier+0x1e/0x40
notifier_call_chain+0x46/0x150
blocking_notifier_call_chain+0x42/0x60
bus_notify+0x2f/0x50
device_add+0x5ed/0x7e0
platform_device_add+0xf5/0x240
mfd_add_devices+0x3f9/0x500
? preempt_count_add+0x4c/0xa0
? up_write+0xa2/0x1b0
? __debugfs_create_file+0xe3/0x150
intel_lpss_probe+0x49f/0x5b0
? pci_conf1_write+0xa3/0xf0
intel_lpss_pci_probe+0xcf/0x110 [intel_lpss_pci]
pci_device_probe+0x95/0x120
really_probe+0xd9/0x370
? __pfx___driver_attach+0x10/0x10
__driver_probe_device+0x73/0x150
driver_probe_device+0x19/0xa0
__driver_attach+0xb6/0x180
? __pfx___driver_attach+0x10/0x10
bus_for_each_dev+0x77/0xd0
bus_add_driver+0x114/0x210
driver_register+0x5b/0x110
? __pfx_intel_lpss_pci_driver_init+0x10/0x10 [intel_lpss_pci]
do_one_initcall+0x57/0x2b0
? kmalloc_trace+0x21e/0x280
? do_init_module+0x1e/0x210
do_init_module+0x5f/0x210
load_module+0x1d37/0x1fc0
? init_module_from_file+0x86/0xd0
init_module_from_file+0x86/0xd0
idempotent_init_module+0x17c/0x230
__x64_sys_finit_module+0x56/0xb0
do_syscall_64+0x6e/0x140
entry_SYSCALL_64_after_hwframe+0x71/0x79
Fixes: 1a75cc710b95 ("iommu/vt-d: Use rbtree to track iommu probed devices")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10689
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20240407011429.136282-1-baolu.lu@linux.intel.com
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The page request queue is per IOMMU, its allocation should be made
NUMA-aware for performance reasons.
Fixes: a222a7f0bb6c ("iommu/vt-d: Implement page request handling")
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20240403214007.985600-1-jacob.jun.pan@linux.intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The commit "iommu/vt-d: Add IOMMU perfmon support" introduce IOMMU
PMU feature, but use the wrong config when set pasid filter.
Fixes: 7232ab8b89e9 ("iommu/vt-d: Add IOMMU perfmon support")
Signed-off-by: Xuchun Shang <xuchun.shang@linux.alibaba.com>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20240401060753.3321318-1-xuchun.shang@linux.alibaba.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The topology rework missed that early_init_amd() tries to re-enable the
Topology Extensions when the BIOS disabled them.
The new parser is invoked before early_init_amd() so the re-enable attempt
happens too late.
Move it into the AMD specific topology parser code where it belongs.
Fixes: f7fb3b2dd92c ("x86/cpu: Provide an AMD/HYGON specific topology parser")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/878r1j260l.ffs@tglx
|
|
A system with NODEID_MSR was reported to crash during early boot without
any output.
The reason is that the union which is used for accessing the bitfields in
the MSR is written wrongly and the resulting executable code accesses the
wrong part of the MSR data.
As a consequence a later division by that value results in 0 and that
result is used for another division as divisor, which obviously does not
work well.
The magic world of C, unions and bitfields:
union {
u64 bita : 3,
bitb : 3;
u64 all;
} x;
x.all = foo();
a = x.bita;
b = x.bitb;
results in the effective executable code of:
a = b = x.bita;
because bita and bitb are treated as union members and therefore both end
up at bit offset 0.
Wrapping the bitfield into an anonymous struct:
union {
struct {
u64 bita : 3,
bitb : 3;
};
u64 all;
} x;
works like expected.
Rework the NODEID_MSR union in exactly that way to cure the problem.
Fixes: f7fb3b2dd92c ("x86/cpu: Provide an AMD/HYGON specific topology parser")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Reported-by: Laura Nao <laura.nao@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Laura Nao <laura.nao@collabora.com>
Link: https://lore.kernel.org/r/20240410194311.596282919@linutronix.de
Closes: https://lore.kernel.org/all/20240322175210.124416-1-laura.nao@collabora.com/
|
|
CPUID 0x80000008 ECX.cpu_nthreads describes the number of threads in the
package. The parser uses this value to initialize the SMT domain level.
That's wrong because cpu_nthreads does not describe the number of threads
per physical core. So this needs to set the CORE domain level and let the
later parsers set the SMT shift if available.
Preset the SMT domain level with the assumption of one thread per core,
which is correct ifrt here are no other CPUID leafs to parse, and propagate
cpu_nthreads and the core level APIC bitwidth into the CORE domain.
Fixes: f7fb3b2dd92c ("x86/cpu: Provide an AMD/HYGON specific topology parser")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Reported-by: Laura Nao <laura.nao@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Laura Nao <laura.nao@collabora.com>
Link: https://lore.kernel.org/r/20240410194311.535206450@linutronix.de
|
|
For consistency with the other CONFIG_MITIGATION_* options, replace the
CONFIG_SPECTRE_BHI_{ON,OFF} options with a single
CONFIG_MITIGATION_SPECTRE_BHI option.
[ mingo: Fix ]
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Sean Christopherson <seanjc@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nikolay Borisov <nik.borisov@suse.com>
Link: https://lore.kernel.org/r/3833812ea63e7fdbe36bf8b932e63f70d18e2a2a.1712813475.git.jpoimboe@kernel.org
|
|
Unlike most other mitigations' "auto" options, spectre_bhi=auto only
mitigates newer systems, which is confusing and not particularly useful.
Remove it.
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Nikolay Borisov <nik.borisov@suse.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/412e9dc87971b622bbbaf64740ebc1f140bff343.1712813475.git.jpoimboe@kernel.org
|
|
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240410164109.233308-1-krzk@kernel.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
DTE[Mode]=0 is not supported when SNP is enabled in the host. That means
to support SNP, IOMMU must be configured with V1 page table (See IOMMU
spec [1] for the details). If user passes kernel command line to configure
IOMMU domains with v2 page table (amd_iommu=pgtbl_v2) then disable SNP
as the user asked by not forcing the page table to v1.
[1] https://www.amd.com/content/dam/amd/en/documents/processor-tech-docs/specifications/48882_IOMMU.pdf
Cc: Ashish Kalra <ashish.kalra@amd.com>
Cc: Michael Roth <michael.roth@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20240410085702.31869-1-vasant.hegde@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
After commit dfa2f0483360 ("tcp: get rid of sysctl_tcp_adv_win_scale"),
we noticed an application-level timeout due to reduced throughput.
Before the commit, for a client that sets SO_RCVBUF to 65k, it takes
around 22 seconds to transfer 10M data. After the commit, it takes 40
seconds. Because our application has a 30-second timeout, this
regression broke the application.
The reason that it takes longer to transfer data is that
tp->scaling_ratio is initialized to a value that results in ~0.25 of
rcvbuf. In our case, SO_RCVBUF is set to 65536 by the application, which
translates to 2 * 65536 = 131,072 bytes in rcvbuf and hence a ~28k
initial receive window.
Later, even though the scaling_ratio is updated to a more accurate
skb->len/skb->truesize, which is ~0.66 in our environment, the window
stays at ~0.25 * rcvbuf. This is because tp->window_clamp does not
change together with the tp->scaling_ratio update when autotuning is
disabled due to SO_RCVBUF. As a result, the window size is capped at the
initial window_clamp, which is also ~0.25 * rcvbuf, and never grows
bigger.
Most modern applications let the kernel do autotuning, and benefit from
the increased scaling_ratio. But there are applications such as kafka
that has a default setting of SO_RCVBUF=64k.
This patch increases the initial scaling_ratio from ~25% to 50% in order
to make it backward compatible with the original default
sysctl_tcp_adv_win_scale for applications setting SO_RCVBUF.
Fixes: dfa2f0483360 ("tcp: get rid of sysctl_tcp_adv_win_scale")
Signed-off-by: Hechao Li <hli@netflix.com>
Reviewed-by: Tycho Andersen <tycho@tycho.pizza>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/netdev/20240402215405.432863-1-hli@netflix.com/
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LOCKDEP detector reported below warning:
----------------------------------------
[ 23.796949] ========================================================
[ 23.796950] WARNING: possible irq lock inversion dependency detected
[ 23.796952] 6.8.0fix+ #811 Not tainted
[ 23.796954] --------------------------------------------------------
[ 23.796954] kworker/0:1/8 just changed the state of lock:
[ 23.796956] ff365325e084a9b8 (&domain->lock){..-.}-{3:3}, at: amd_iommu_flush_iotlb_all+0x1f/0x50
[ 23.796969] but this lock took another, SOFTIRQ-unsafe lock in the past:
[ 23.796970] (pd_bitmap_lock){+.+.}-{3:3}
[ 23.796972]
and interrupts could create inverse lock ordering between them.
[ 23.796973]
other info that might help us debug this:
[ 23.796974] Chain exists of:
&domain->lock --> &dev_data->lock --> pd_bitmap_lock
[ 23.796980] Possible interrupt unsafe locking scenario:
[ 23.796981] CPU0 CPU1
[ 23.796982] ---- ----
[ 23.796983] lock(pd_bitmap_lock);
[ 23.796985] local_irq_disable();
[ 23.796985] lock(&domain->lock);
[ 23.796988] lock(&dev_data->lock);
[ 23.796990] <Interrupt>
[ 23.796991] lock(&domain->lock);
Fix this issue by disabling interrupt when acquiring pd_bitmap_lock.
Note that this is temporary fix. We have a plan to replace custom bitmap
allocator with IDA allocator.
Fixes: 87a6f1f22c97 ("iommu/amd: Introduce per-device domain ID to fix potential TLB aliasing issue")
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20240404102717.6705-1-vasant.hegde@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Eric Woudstra says:
====================
rtl8226b/8221b add C45 instances and SerDes switching
Based on the comments in [PATCH net-next]
"Realtek RTL822x PHY rework to c45 and SerDes interface switching"
Adds SerDes switching interface between 2500base-x and sgmii for
rtl8221b and rtl8226b.
Add get_rate_matching() for rtl8226b and rtl8221b, reading the serdes
mode from phy.
Driver instances are added for rtl8226b and rtl8221b for Clause 45
access only. The existing code is not touched, they use newly added
functions. They also use the same rtl822xb_config_init() and
rtl822xb_get_rate_matching() as these functions also can be used for
direct Clause 45 access. Also Adds definition of MMC 31 registers,
which cannot be used through C45-over-C22, only when phydev->is_c45
is set.
Change rtlgen_get_speed() so the register value is passed as argument.
Using Clause 45 access, this value is retrieved differently.
Rename it to rtlgen_decode_speed() and add a call to it in
rtl822x_c45_read_status().
Add rtl822x_c45_get_features() to set supported port for rtl8221b.
Then 1 quirk is added for sfp modules known to have a rtl8221b
behind RollBall, Clause 45 only, protocol.
Changed in PATCH v4:
* Changed switch to if statement in rtl822xb_get_rate_matching()
* Removed setting ETHTOOL_LINK_MODE_MII_BIT in rtl822x_c45_get_features()
Changed in PATCH v3:
* Only apply to rtl8221b and rtl8226b phy's
* Set phydev->rate_matching in .config_init()
* Removed OEM SFP fixup for now, as there are modules with the same
vendor name/PN, but with different PHY's. We found rtl8221b, but
also the ty8821, which is not yet supported.
Changed in PATCH v2:
* Set author to Marek for the commit of the new C45 instances
* Separate commit for setting supported ports
* Renamed rtlgen_get_speed to rtlgen_decode_speed
* Always fill in possible interfaces
* Renamed sfp_fixup_oem_2_5g to sfp_fixup_oem_2_5gbaset
* Only update phydev->interface when link is up
Alexander Couzens (1):
net: phy: realtek: configure SerDes mode for rtl822xb PHYs
Eric Woudstra (3):
net: phy: realtek: add get_rate_matching() for rtl822xb PHYs
net: phy: realtek: Change rtlgen_get_speed() to rtlgen_decode_speed()
net: phy: realtek: add rtl822x_c45_get_features() to set supported
port
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add quirk for another RollBall copper transceiver: Turris RTSFP-2.5G,
containing 2.5g capable RTL8221B PHY.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sets ETHTOOL_LINK_MODE_TP_BIT in phydev->supported.
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The value of the register to determine the speed, is retrieved
differently when using Clause 45 only. To use the rtlgen_get_speed()
function in this case, pass the value of the register as argument to
rtlgen_get_speed(). The function would then always return 0, so change it
to void. A better name for this function now is rtlgen_decode_speed().
Replace a call to genphy_read_status() followed by rtlgen_get_speed()
with a call to rtlgen_read_status() in rtl822x_read_status().
Add reading speed to rtl822x_c45_read_status().
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Collected from several commits in [PATCH net-next]
"Realtek RTL822x PHY rework to c45 and SerDes interface switching"
The instances are used by Clause 45 only accessible PHY's on several sfp
modules, which are using RollBall protocol.
Signed-off-by: Marek Behún <kabel@kernel.org>
[ Added matching functions to differentiate C45 instances ]
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Uses vendor register to determine if SerDes is setup in rate-matching mode.
Rate-matching only supported when SerDes is set to 2500base-x.
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rtl8221b and rtl8226b series support switching SerDes mode between
2500base-x and sgmii based on the negotiated copper speed.
Configure this switching mode according to SerDes modes supported by
host.
There is an additional datasheet for RTL8226B/RTL8221B called
"SERDES MODE SETTING FLOW APPLICATION NOTE" where a sequence is
described to setup interface and rate adapter mode.
However, there is no documentation about the meaning of registers
and bits, it's literally just magic numbers and pseudo-code.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
[ refactored, dropped HiSGMII mode and changed commit message ]
Signed-off-by: Marek Behún <kabel@kernel.org>
[ changed rtl822x_update_interface() to use vendor register ]
[ always fill in possible interfaces ]
[ only apply to rtl8221b and rtl8226b phy's ]
[ set phydev->rate_matching in .config_init() ]
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: should come before them, without any blank lines. As the
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It turns out - btree splits happen with the rest of the transaction
still locked, to avoid unnecessary restarts, which means using nofail
doesn't work here - we can deadlock.
Fortunately, we now have the ability to return errors here.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Russell King says:
====================
net: dsa: allow phylink_mac_ops in DSA drivers
This series showcases my idea of moving the phylink_mac_ops into DSA
drivers, using mv88e6xxx as an example. Since I'm only changing one
driver, providing the mac_ops has to be optional and the existing shims
need to be kept for unconverted drivers.
The first patch introduces a new helper that converts from the
phylink_config structure that phylink uses to communicate with MAC
drivers to the dsa_port structure. From this, DSA drivers can get
the dsa_switch structure and thus their implementation specific
data structure, and they can also retrieve the port index.
The second patch adds the support to the core DSA layer to allow
DSA drivers to provide phylink_mac_ops.
The third patch converts mv88e6xxx to use this.
I initially made this change after adding yet more phylink to DSA
driver shims for my work with phylink-based EEE support, and decided
that it was getting silly to keep implementing more and more shims.
There are cases where shims don't work well - we had already tripped
over a case a few years ago when the phylink mac_select_pcs operation
was introduced. Phylink tested for the presence of this in the ops
structure, but with DSA shims, this doesn't necessarily mean that
the sub-driver supports this method. The only way to find that out
is to call the method with dummy values and check the return code.
The same thing was partly true when adding EEE support, and I ended
up with this in phylink to determine whether the MAC supported EEE:
+static bool phylink_mac_supports_eee(struct phylink *pl)
+{
+ return pl->mac_ops->mac_disable_tx_lpi &&
+ pl->mac_ops->mac_enable_tx_lpi &&
+ pl->config->lpi_capabilities;
+}
because merely testing for the presence of the operations is
insufficient when shims are involved - and it wasn't possible to call
these functions in the way that mac_select_pcs could be called.
So, I think it's time to get away from this shimming model and instead
have drivers directly interface to the various subsystems.
This converts mv88e6xxx. I have similar patches for other DSA drivers
that will be sent once this has been reviewed.
====================
Link: https://lore.kernel.org/r/ZhbrbM+d5UfgafGp@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert mv88e6xxx to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1rudqK-006K9N-HY@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rather than having a shim for each and every phylink MAC operation,
allow DSA switch drivers to provide their own ops structure. When a
DSA driver provides the phylink MAC operations, the shimmed ops must
not be provided, so fail an attempt to register a switch with both
the phylink_mac_ops in struct dsa_switch and the phylink_mac_*
operations populated in dsa_switch_ops populated.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1rudqF-006K9H-Cc@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We convert from a phylink_config struct to a dsa_port struct in many
places, let's provide a helper for this.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/E1rudqA-006K9B-85@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The variable decrypted is being assigned a value that is never read,
the control of flow after the assignment is via an return path and
decrypted is not referenced in this path. The assignment is redundant
and can be removed.
Cleans up clang scan warning:
net/tls/tls_sw.c:2150:4: warning: Value stored to 'decrypted' is never
read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240410144136.289030-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
RTO_ONLINK was a flag used in ->flowi4_tos that allowed to alter the
scope of an IPv4 route lookup. Setting this flag was equivalent to
specifying RT_SCOPE_LINK in ->flowi4_scope.
With commit ec20b2830093 ("ipv4: Set scope explicitly in
ip_route_output()."), the last users of RTO_ONLINK have been removed.
Therefore, we can now drop the code that checked this bit and stop
modifying ->flowi4_scope in ip_route_output_key_hash().
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/57de760565cab55df7b129f523530ac6475865b2.1712754146.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When reading received messages from a socket with MSG_PEEK, we may want
to read the contents with an offset, like we can do with pread/preadv()
when reading files. Currently, it is not possible to do that.
In this commit, we add support for the SO_PEEK_OFF socket option for TCP,
in a similar way it is done for Unix Domain sockets.
In the iperf3 log examples shown below, we can observe a throughput
improvement of 15-20 % in the direction host->namespace when using the
protocol splicer 'pasta' (https://passt.top).
This is a consistent result.
pasta(1) and passt(1) implement user-mode networking for network
namespaces (containers) and virtual machines by means of a translation
layer between Layer-2 network interface and native Layer-4 sockets
(TCP, UDP, ICMP/ICMPv6 echo).
Received, pending TCP data to the container/guest is kept in kernel
buffers until acknowledged, so the tool routinely needs to fetch new
data from socket, skipping data that was already sent.
At the moment this is implemented using a dummy buffer passed to
recvmsg(). With this change, we don't need a dummy buffer and the
related buffer copy (copy_to_user()) anymore.
passt and pasta are supported in KubeVirt and libvirt/qemu.
jmaloy@freyr:~/passt$ perf record -g ./pasta --config-net -f
SO_PEEK_OFF not supported by kernel.
jmaloy@freyr:~/passt# iperf3 -s
-----------------------------------------------------------
Server listening on 5201 (test #1)
-----------------------------------------------------------
Accepted connection from 192.168.122.1, port 44822
[ 5] local 192.168.122.180 port 5201 connected to 192.168.122.1 port 44832
[ ID] Interval Transfer Bitrate
[ 5] 0.00-1.00 sec 1.02 GBytes 8.78 Gbits/sec
[ 5] 1.00-2.00 sec 1.06 GBytes 9.08 Gbits/sec
[ 5] 2.00-3.00 sec 1.07 GBytes 9.15 Gbits/sec
[ 5] 3.00-4.00 sec 1.10 GBytes 9.46 Gbits/sec
[ 5] 4.00-5.00 sec 1.03 GBytes 8.85 Gbits/sec
[ 5] 5.00-6.00 sec 1.10 GBytes 9.44 Gbits/sec
[ 5] 6.00-7.00 sec 1.11 GBytes 9.56 Gbits/sec
[ 5] 7.00-8.00 sec 1.07 GBytes 9.20 Gbits/sec
[ 5] 8.00-9.00 sec 667 MBytes 5.59 Gbits/sec
[ 5] 9.00-10.00 sec 1.03 GBytes 8.83 Gbits/sec
[ 5] 10.00-10.04 sec 30.1 MBytes 6.36 Gbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate
[ 5] 0.00-10.04 sec 10.3 GBytes 8.78 Gbits/sec receiver
-----------------------------------------------------------
Server listening on 5201 (test #2)
-----------------------------------------------------------
^Ciperf3: interrupt - the server has terminated
jmaloy@freyr:~/passt#
logout
[ perf record: Woken up 23 times to write data ]
[ perf record: Captured and wrote 5.696 MB perf.data (35580 samples) ]
jmaloy@freyr:~/passt$
jmaloy@freyr:~/passt$ perf record -g ./pasta --config-net -f
SO_PEEK_OFF supported by kernel.
jmaloy@freyr:~/passt# iperf3 -s
-----------------------------------------------------------
Server listening on 5201 (test #1)
-----------------------------------------------------------
Accepted connection from 192.168.122.1, port 52084
[ 5] local 192.168.122.180 port 5201 connected to 192.168.122.1 port 52098
[ ID] Interval Transfer Bitrate
[ 5] 0.00-1.00 sec 1.32 GBytes 11.3 Gbits/sec
[ 5] 1.00-2.00 sec 1.19 GBytes 10.2 Gbits/sec
[ 5] 2.00-3.00 sec 1.26 GBytes 10.8 Gbits/sec
[ 5] 3.00-4.00 sec 1.36 GBytes 11.7 Gbits/sec
[ 5] 4.00-5.00 sec 1.33 GBytes 11.4 Gbits/sec
[ 5] 5.00-6.00 sec 1.21 GBytes 10.4 Gbits/sec
[ 5] 6.00-7.00 sec 1.31 GBytes 11.2 Gbits/sec
[ 5] 7.00-8.00 sec 1.25 GBytes 10.7 Gbits/sec
[ 5] 8.00-9.00 sec 1.33 GBytes 11.5 Gbits/sec
[ 5] 9.00-10.00 sec 1.24 GBytes 10.7 Gbits/sec
[ 5] 10.00-10.04 sec 56.0 MBytes 12.1 Gbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate
[ 5] 0.00-10.04 sec 12.9 GBytes 11.0 Gbits/sec receiver
-----------------------------------------------------------
Server listening on 5201 (test #2)
-----------------------------------------------------------
^Ciperf3: interrupt - the server has terminated
logout
[ perf record: Woken up 20 times to write data ]
[ perf record: Captured and wrote 5.040 MB perf.data (33411 samples) ]
jmaloy@freyr:~/passt$
The perf record confirms this result. Below, we can observe that the
CPU spends significantly less time in the function ____sys_recvmsg()
when we have offset support.
Without offset support:
----------------------
jmaloy@freyr:~/passt$ perf report -q --symbol-filter=do_syscall_64 \
-p ____sys_recvmsg -x --stdio -i perf.data | head -1
46.32% 0.00% passt.avx2 [kernel.vmlinux] [k] do_syscall_64 ____sys_recvmsg
With offset support:
----------------------
jmaloy@freyr:~/passt$ perf report -q --symbol-filter=do_syscall_64 \
-p ____sys_recvmsg -x --stdio -i perf.data | head -1
28.12% 0.00% passt.avx2 [kernel.vmlinux] [k] do_syscall_64 ____sys_recvmsg
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240409152805.913891-1-jmaloy@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 3e2f544dd8a33 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240409133307.2058099-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With commit 34d21de99cea9 ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the qmi_wwan driver and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240409133307.2058099-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
- Use for_each_netdev_dump() to no longer rely
on net->dev_index_head hash table.
- No longer care of net->dev_base_seq
- Fix return value at the end of a dump,
so that NLMSG_DONE can be appended to current skb,
saving one recvmsg() system call.
- No longer grab RTNL, RCU protection is enough,
afer adding one READ_ONCE(mdev->input_enabled)
in mpls_netconf_fill_devconf()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240410111951.2673193-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
include/net/flow_offload.h:351: warning:
No description found for return value of 'flow_offload_has_one_action'
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Link: https://lore.kernel.org/r/20240410114718.15145-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Q counters are device-level counters that track specific
events, among which are out_of_buffer events. These events
occur when packets are dropped due to a lack of receive
buffer in the RX queue.
Expose the total number of out_of_buffer events on the
VFs/SFs to their respective representor, using the
"ip stats group link" under the name of "rx_missed".
The "rx_missed" equals the sum of all
Q counters out_of_buffer values allocated on the VFs/SFs.
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240410214154.250583-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Mina Almasry says:
====================
Minor cleanups to skb frag ref/unref
This series is largely motivated by a recent discussion where there was
some confusion on how to properly ref/unref pp pages vs non pp pages:
https://lore.kernel.org/netdev/CAHS8izOoO-EovwMwAm9tLYetwikNPxC0FKyVGu1TPJWSz4bGoA@mail.gmail.com/T/#t
There is some subtely there because pp uses page->pp_ref_count for
refcounting, while non-pp uses get_page()/put_page() for ref counting.
Getting the refcounting pairs wrong can lead to kernel crash.
Additionally currently it may not be obvious to skb users unaware of
page pool internals how to properly acquire a ref on a pp frag. It
requires checking of skb->pp_recycle & is_pp_page() to make the correct
calls and may require some handling at the call site aware of arguable pp
internals.
This series is a minor refactor with a couple of goals:
1. skb users should be able to ref/unref a frag using
[__]skb_frag_[un]ref() functions without needing to understand pp
concepts and pp_ref_count vs get/put_page() differences.
2. reference counting functions should have a mirror opposite. I.e. there
should be a foo_unref() to every foo_ref() with a mirror opposite
implementation (as much as possible).
This is RFC to collect feedback if this change is desirable, but also so
that I don't race with the fix for the issue Dragos is seeing for his
crash.
https://lore.kernel.org/lkml/CAHS8izN436pn3SndrzsCyhmqvJHLyxgCeDpWXA4r1ANt3RCDLQ@mail.gmail.com/T/
====================
Link: https://lore.kernel.org/r/20240410190505.1225848-1-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Refactor some of the skb frag ref/unref helpers for improved clarity.
Implement napi_pp_get_page() to be the mirror counterpart of
napi_pp_put_page().
Implement skb_page_ref() to be the mirror of skb_page_unref().
Improve __skb_frag_ref() to become a mirror counterpart of
__skb_frag_unref(). Previously unref could handle pp & non-pp pages,
while the ref could only handle non-pp pages. Now both the ref & unref
helpers can correctly handle both pp & non-pp pages.
Now that __skb_frag_ref() can handle both pp & non-pp pages, remove
skb_pp_frag_ref(), and use __skb_frag_ref() instead. This lets us
remove pp specific handling from skb_try_coalesce.
Additionally, since __skb_frag_ref() can now handle both pp & non-pp
pages, a latent issue in skb_shift() should now be fixed. Previously
this function would do a non-pp ref & pp unref on potential pp frags
(fragfrom). After this patch, skb_shift() should correctly do a pp
ref/unref on pp frags.
Signed-off-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240410190505.1225848-3-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a new header, linux/skbuff_ref.h, which contains all the skb_*_ref()
helpers. Many of the consumers of skbuff.h do not actually use any of
the skb ref helpers, and we can speed up compilation a bit by minimizing
this header file.
Additionally in the later patch in the series we add page_pool support
to skb_frag_ref(), which requires some page_pool dependencies. We can
now add these dependencies to skbuff_ref.h instead of a very ubiquitous
skbuff.h
Signed-off-by: Mina Almasry <almasrymina@google.com>
Link: https://lore.kernel.org/r/20240410190505.1225848-2-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This uses calloc instead of doing the multiplication which might
overflow.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
Fixes for v6.9
Display:
- Fixes for PM refcount leak when DP goes to disconnected state and
also when link training fails. This is also one of the issues found
with the pm runtime series
- Add missing newlines to prints in msm_fb and msm_kms
- Change permissions of some dpu debugfs entries which write to const
data from catalog to read-only to avoid protection faults
- Fix the interface table for the catalog of X1E80100. This is an
important fix to bringup DP for X1E80100.
- Logging fix to print the callback symbol in the invalid IRQ message
case rather than printing when its known to be NULL.
- Bindings fix to add DP node as child of mdss for mdss node
- Minor typo fix in DP driver API which handles port status change
GPU:
- fix CHRASHDUMP_READ()
- fix HHB (highest bank bit) for a619 to fix UBWC corruption
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvFwRUcHGWva7oDeydq1PTiZMduuykCD2MWaFrT4iMGZA@mail.gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl fixes from Dave Jiang:
- Fix index of Clear Event Record handles in cxl_clear_event_record()
- Fix use before init of map->reg_type in cxl_decode_regblock()
- Fix initialization of mbox_cmd.size_out in cxl_mem_get_records_log()
- Fix CXL path access_coordinate computation:
- Remove unneded check of iter in loop
- Fix of retrieving of access_coordinate in PCI topology walk
- Fix of incorrect region access_coordinate data calculation
- Consolidate of access_coordinates attached to downstream port
context
- Add check to validate access_coordinate validity to prevent
incorrect data being exposed via sysfs
* tag 'cxl-fixes-6.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl: Add checks to access_coordinate calculation to fail missing data
cxl: Consolidate dport access_coordinate ->hb_coord and ->sw_coord into ->coord
cxl: Fix incorrect region perf data calculation
cxl: Fix retrieving of access_coordinates in PCIe path
cxl: Remove checking of iter in cxl_endpoint_get_perf_coordinates()
cxl/core: Fix initialization of mbox_cmd.size_out in get event
cxl/core/regs: Fix usage of map->reg_type in cxl_decode_regblock() before assigned
cxl/mem: Fix for the index of Clear Event Record Handle
|
