| Age | Commit message (Collapse) | Author |
|---|
|
Trusted VFs are allowed to modify MAC address, even when PF
has assigned one.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clear flags when reset command processed successfully for components
specified.
Fixes: 6502ad5963a5 ("bnxt_en: Add ETH_RESET_AP support")
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the RDMA driver is registered, use a new VNIC mode that allows
RDMA traffic to be seen on the netdev in promiscuous mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the default ring logic to select default number of rings to be up to
8 per port if the default rings x NIC ports <= total CPUs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor changes, such as new extended port statistics.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warning:
net/8021q/vlan_core.c:168:6: warning:
symbol 'vlan_hw_filter_capable' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-03-30
This series contains updates to mlx5 core and mlx5e netdev drivers.
The main highlight of this series is the RX optimizations for striding RQ path,
introduced by Tariq.
First Four patches are trivial misc cleanups.
- Spelling mistake fix
- Dead code removal
- Warning messages
RX optimizations for striding RQ:
1) RX refactoring, cleanups and micro optimizations
- MTU calculation simplifications, obsoletes some WQEs-to-packets translation
functions and helps delete ~60 LOC.
- Do not busy-wait a pending UMR completion.
- post the new values of UMR WQE inline, instead of using a data pointer.
- use pre-initialized structures to save calculations in datapath.
2) Use linear SKB in Striding RQ "build_skb", (Using linear SKB has many advantages):
- Saves a memcpy of the headers.
- No page-boundary checks in datapath.
- No filler CQEs.
- Significantly smaller CQ.
- SKB data continuously resides in linear part, and not split to
small amount (linear part) and large amount (fragment).
This saves datapath cycles in driver and improves utilization
of SKB fragments in GRO.
- The fragments of a resulting GRO SKB follow the IP forwarding
assumption of equal-size fragments.
implementation details:
HW writes the packets to the beginning of a stride,
i.e. does not keep headroom. To overcome this we make sure we can
extend backwards and use the last bytes of stride i-1.
Extra care is needed for stride 0 as it has no preceding stride.
We make sure headroom bytes are available by shifting the buffer
pointer passed to HW by headroom bytes.
This configuration now becomes default, whenever capable.
Of course, this implies turning LRO off.
Performance testing:
ConnectX-5, single core, single RX ring, default MTU.
UDP packet rate, early drop in TC layer:
--------------------------------------------
| pkt size | before | after | ratio |
--------------------------------------------
| 1500byte | 4.65 Mpps | 5.96 Mpps | 1.28x |
| 500byte | 5.23 Mpps | 5.97 Mpps | 1.14x |
| 64byte | 5.94 Mpps | 5.96 Mpps | 1.00x |
--------------------------------------------
TCP streams: ~20% gain
3) Support XDP over Striding RQ:
Now that linear SKB is supported over Striding RQ,
we can support XDP by setting stride size to PAGE_SIZE
and headroom to XDP_PACKET_HEADROOM.
Striding RQ is capable of a higher packet-rate than
conventional RQ.
Performance testing:
ConnectX-5, 24 rings, default MTU.
CQE compression ON (to reduce completions BW in PCI).
XDP_DROP packet rate:
--------------------------------------------------
| pkt size | XDP rate | 100GbE linerate | pct% |
--------------------------------------------------
| 64byte | 126.2 Mpps | 148.0 Mpps | 85% |
| 128byte | 80.0 Mpps | 84.8 Mpps | 94% |
| 256byte | 42.7 Mpps | 42.7 Mpps | 100% |
| 512byte | 23.4 Mpps | 23.4 Mpps | 100% |
--------------------------------------------------
4) Remove mlx5 page_ref bulking in Striding RQ and use page_ref_inc only when needed.
Without this bulking, we have:
- no atomic ops on WQE allocation or free
- one atomic op per SKB
- In the default MTU configuration (1500, stride size is 2K),
the non-bulking method execute 2 atomic ops as before
- For larger MTUs with stride size of 4K, non-bulking method
executes only a single op.
- For XDP (stride size of 4K, no SKBs), non-bulking have no atomic ops per packet at all.
Performance testing:
ConnectX-5, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz.
Single core packet rate (64 bytes).
Early drop in TC: no degradation.
XDP_DROP:
before: 14,270,188 pps
after: 20,503,603 pps, 43% improvement.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fixes and more traces
Here are some patches that add some more tracepoints to AF_RXRPC and fix
some issues therein:
(1) Fix the use of VERSION packets to keep firewall routes open.
(2) Fix the incorrect current time usage in a tracepoint.
(3) Fix Tx ring annotation corruption.
(4) Fix accidental conversion of call-level abort into connection-level
abort.
(5) Fix calculation of resend time.
(6) Remove a couple of unused variables.
(7) Fix a bunch of checker warnings and an error. Note that not all
warnings can be quashed as checker doesn't seem to correctly handle
seqlocks.
(8) Fix a potential race between call destruction and socket/net
destruction.
(9) Add a tracepoint to track rxrpc_local refcounting.
(10) Fix an apparent leak of rxrpc_local objects.
(11) Add a tracepoint to track rxrpc_peer refcounting.
(12) Fix a leak of rxrpc_peer objects.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variables, msg and data, have the same value. This patch removes
the extra one.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than use an on-stack array to copy a broadcast address, use
the generic eth_broadcast_addr function to save a trivial amount of
object code.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kirill Tkhai says:
====================
net_rwsem fixes
there is wext_netdev_notifier_call()->wireless_nlevent_flush()
netdevice notifier, which takes net_rwsem, so we can't take
net_rwsem in {,un}register_netdevice_notifier().
Since {,un}register_netdevice_notifier() is executed under
pernet_ops_rwsem, net_namespace_list can't change, while we
holding it, so there is no need net_rwsem in these functions [1/2].
The same is in [2/2]. We make callers of __rtnl_link_unregister()
take pernet_ops_rwsem, and close the race with setup_net()
and cleanup_net(), so __rtnl_link_unregister() does not need it.
This also fixes the problem of that __rtnl_link_unregister() does
not see initializing and exiting nets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function calls call_netdevice_notifier(), which also
may take net_rwsem. So, we can't use net_rwsem here.
This patch makes callers of this functions take pernet_ops_rwsem,
like register_netdevice_notifier() does. This will protect
the modifications of net_namespace_list, and allows notifiers
to take it (they won't have to care about context).
Since __rtnl_link_unregister() is used on module load
and unload (which are not frequent operations), this looks
for me better, than make all call_netdevice_notifier()
always executing in "protected net_namespace_list" context.
Also, this fixes the problem we had a deal in 328fbe747ad4
"Close race between {un, }register_netdevice_notifier and ...",
and guarantees __rtnl_link_unregister() does not skip
exitting net.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These functions take net_rwsem, while wireless_nlevent_flush()
also takes it. But down_read() can't be taken recursive,
because of rw_semaphore design, which prevents it to be occupied
by only readers forever.
Since we take pernet_ops_rwsem in {,un}register_netdevice_notifier(),
net list can't change, so these down_read()/up_read() can be removed.
Fixes: f0b07bb151b0 "net: Introduce net_rwsem to protect net_namespace_list"
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need for explicit calls of devm_kfree(), as the allocated
memory will be freed during driver's detach.
The driver core clears the driver data to NULL after device_release.
Thus, it is not needed to manually clear the device driver data to NULL.
So remove the unnecessary pci_set_drvdata() and devm_kfree().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change nsim_devlink_setup to return any error back to the caller and
update nsim_init to handle it.
Requested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jon Maloy says:
====================
tipc: slim down name table
We clean up and improve the name binding table:
- Replace the memory consuming 'sub_sequence/service range' array with
an RB tree.
- Introduce support for overlapping service sequences/ranges
v2: #1: Fixed a missing initialization reported by David Miller
#4: Obsoleted and replaced a few more macros to get a consistent
terminology in the API.
#5: Added new commit to fix a potential string overflow bug (it
is still only in net-next) reported by Arnd Bergmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc points out that the combined length of the fixed-length inputs to
l->name is larger than the destination buffer size:
net/tipc/link.c: In function 'tipc_link_create':
net/tipc/link.c:465:26: error: '%s' directive writing up to 32 bytes
into a region of size between 26 and 58 [-Werror=format-overflow=]
sprintf(l->name, "%s:%s-%s:unknown", self_str, if_name, peer_str);
net/tipc/link.c:465:2: note: 'sprintf' output 11 or more bytes
(assuming 75) into a destination of size 60
sprintf(l->name, "%s:%s-%s:unknown", self_str, if_name, peer_str);
A detailed analysis reveals that the theoretical maximum length of
a link name is:
max self_str + 1 + max if_name + 1 + max peer_str + 1 + max if_name =
16 + 1 + 15 + 1 + 16 + 1 + 15 = 65
Since we also need space for a trailing zero we now set MAX_LINK_NAME
to 68.
Just to be on the safe side we also replace the sprintf() call with
snprintf().
Fixes: 25b0b9c4e835 ("tipc: handle collisions of 32-bit node address
hash values")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The three address type structs in the user API have names that in
reality reflect the specific, non-Linux environment where they were
originally created.
We now give them more intuitive names, in accordance with how TIPC is
described in the current documentation.
struct tipc_portid -> struct tipc_socket_addr
struct tipc_name -> struct tipc_service_addr
struct tipc_name_seq -> struct tipc_service_range
To avoid confusion, we also update some commmets and macro names to
match the new terminology.
For compatibility, we add macros that map all old names to the new ones.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the new RB tree structure for service ranges it becomes possible to
solve an old problem; - we can now allow overlapping service ranges in
the table.
When inserting a new service range to the tree, we use 'lower' as primary
key, and when necessary 'upper' as secondary key.
Since there may now be multiple service ranges matching an indicated
'lower' value, we must also add the 'upper' value to the functions
used for removing publications, so that the correct, corresponding
range item can be found.
These changes guarantee that a well-formed publication/withdrawal item
from a peer node never will be rejected, and make it possible to
eliminate the problematic backlog functionality we currently have for
handling such cases.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function tipc_nametbl_translate() function is ugly and hard to
follow. This can be improved somewhat by introducing a stack variable
for holding the publication list to be used and re-ordering the if-
clauses for selection of algorithm.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current design of the binding table has an unnecessary memory
consuming and complex data structure. It aggregates the service range
items into an array, which is expanded by a factor two every time it
becomes too small to hold a new item. Furthermore, the arrays never
shrink when the number of ranges diminishes.
We now replace this array with an RB tree that is holding the range
items as tree nodes, each range directly holding a list of bindings.
This, along with a few name changes, improves both readability and
volume of the code, as well as reducing memory consumption and hopefully
improving cache hit rate.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nikolay Aleksandrov says:
====================
net: bridge: MTU handling changes
As previously discussed the recent changes break some setups and could lead
to packet drops. Thus the first patch reverts the behaviour for the bridge
to follow the minimum MTU but also keeps the ability to set the MTU to the
maximum (out of all ports) if vlan filtering is enabled. Patch 02 is the
bigger change in behaviour - we've always had trouble when configuring
bridges and their MTU which is auto tuning on port events
(add/del/changemtu), which means config software needs to chase it and fix
it after each such event, after patch 02 we allow the user to configure any
MTU (ETH_MIN/MAX limited) but once that is done the bridge stops auto
tuning and relies on the user to keep the MTU correct.
This should be compatible with cases that don't touch the MTU (or set it
to the same value), while allowing to configure the MTU and not worry
about it changing afterwards.
The patches are intentionally split like this, so that if they get accepted
and there are any complaints patch 02 can be reverted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Roopa noted today the biggest source of problems when configuring
bridge and ports is that the bridge MTU keeps changing automatically on
port events (add/del/changemtu). That leads to inconsistent behaviour
and network config software needs to chase the MTU and fix it on each
such event. Let's improve on that situation and allow for the user to
set any MTU within ETH_MIN/MAX limits, but once manually configured it
is the user's responsibility to keep it correct afterwards.
In case the MTU isn't manually set - the behaviour reverts to the
previous and the bridge follows the minimum MTU.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently the bridge was changed to automatically set maximum MTU on port
events (add/del/changemtu) when vlan filtering is enabled, but that
actually changes behaviour in a way which breaks some setups and can lead
to packet drops. In order to still allow that maximum to be set while being
compatible, we add the ability for the user to tune the bridge MTU up to
the maximum when vlan filtering is enabled, but that has to be done
explicitly and all port events (add/del/changemtu) lead to resetting that
MTU to the minimum as before.
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vadim Lomovtsev says:
====================
net: thunderx: implement DMAC filtering support
By default CN88XX BGX accepts all incoming multicast and broadcast
packets and filtering is disabled. The nic driver doesn't provide
an ability to change such behaviour.
This series is to implement DMAC filtering management for CN88XX
nic driver allowing user to enable/disable filtering and configure
specific MAC addresses to filter traffic.
Changes from v1:
build issues:
- update code in order to address compiler warnings;
checkpatch.pl reported issues:
- update code in order to fit 80 symbols length;
- update commit descriptions in order to fit 80 symbols length;
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ndo_set_rx_mode() is called from atomic context which causes
messages response timeouts while VF to PF communication via MSIx.
To get rid of that we're copy passed mc list, parse flags and queue
handling of kernel request to ordered workqueue.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
request
The kernel calls ndo_set_rx_mode() callback from atomic context which
causes messaging timeouts between VF and PF (as they’re implemented via
MSIx). So in order to handle ndo_set_rx_mode() we need to get rid of it.
This commit implements necessary workqueue related structures to let VF
queue kernel request processing in non-atomic context later.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit is to add message handling for ndo_set_rx_mode()
callback at PF side.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel calls ndo_set_rx_mode() callback supplying it will all necessary
info, such as device state flags, multicast mac addresses list and so on.
Since we have only 128 bits to communicate with PF we need to initiate
several requests to PF with small/short operation each based on input data.
So this commit implements following PF messages codes along with new
data structures for them:
NIC_MBOX_MSG_RESET_XCAST to flush all filters configured for this
particular network interface (VF)
NIC_MBOX_MSG_ADD_MCAST to add new MAC address to DMAC filter registers
for this particular network interface (VF)
NIC_MBOX_MSG_SET_XCAST to apply filtering configuration to filter control
register
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ThunderX NIC could be partitioned to up to 128 VFs and thus
represented to system. Each VF is mapped to pair BGX:LMAC, and each of VF
is configured by kernel individually. Eventually the bunch of VFs could be
mapped onto same pair BGX:LMAC and thus could cause several multicast
filtering configuration requests to LMAC with the same MAC addresses.
This commit is to add ThunderX NIC BGX filtering manipulation routines.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ThunderX NIC has two Ethernet Interfaces (BGX) each of them could has
up to four Logical MACs configured. Each of BGX has 32 filters to be
configured for filtering ingress packets. The number of filters available
to particular LMAC is from 8 (if we have four LMACs configured per BGX)
up to 32 (in case of only one LMAC is configured per BGX).
At the same time the NIC could present up to 128 VFs to OS as network
interfaces, each of them kernel will configure with set of MAC addresses
for filtering. So to prevent dupes in BGX filter registers from different
network interfaces it is required to cache and track all filter
configuration requests prior to applying them onto BGX filter registers.
This commit is to update LMAC structures with control fields to
allocate/releasing filters tracking list along with implementing
dmac array allocate/release per LMAC.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ThunderX NIC has set of registers which allows to configure
filter policy for ingress packets. There are three possible regimes
of filtering multicasts, broadcasts and unicasts: accept all, reject all
and accept filter allowed only.
Current implementation has enum with all of them and two generic macro
for enabling filtering et all (CAM_ACCEPT) and enabling/disabling
broadcast packets, which also should be corrected in order to represent
register bits properly. All these values are private for driver and
there is no need to ‘publish’ them via header file.
This commit is to move filtering register manipulation values from
header file into source with explicit assignment of exact register
values to them to be used while register configuring.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Martin Blumenstingl says:
====================
Meson8m2 support for dwmac-meson8b
The Meson8m2 SoC is an updated version of the Meson8 SoC. Some of the
peripherals are shared with Meson8b (for example the watchdog registers
and the internal temperature sensor calibration procedure).
Meson8m2 also seems to include the same Gigabit MAC register layout as
Meson8b.
The registers in the Amlogic dwmac "glue" seem identical between Meson8b
and Meson8m2. Manual testing seems to confirm this.
To be extra-safe a new compatible string is added because there's no
(public) documentation on the Meson8m2 SoC. This will allow us to
implement any SoC-specific variations later on (if needed).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Meson8m2 SoC uses a similar (potentially even identical) register
layout as the Meson8b and GXBB SoCs for the dwmac glue.
Add a new compatible string and update the module description to
indicate support for these SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Meson8m2 SoC uses a similar (potentially even identical) register
layout for the dwmac glue as Meson8b and GXBB. Unfortunately there is no
documentation available.
Testing shows that both, RMII and RGMII PHYs are working if they are
configured as on Meson8b. Add a new compatible string to the
documentation so differences (if there are any) between Meson8m2 and the
other SoCs can be taken care of within the driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Two fixlets"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/hwbp: Simplify the perf-hwbp code, fix documentation
perf/x86/intel: Fix linear IP of PEBS real_ip on Haswell and later CPUs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Two UV platform fixes, and a kbuild fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform/UV: Fix critical UV MMR address error
x86/platform/uv/BAU: Add APIC idt entry
x86/purgatory: Avoid creating stray .<pid>.d files, remove -MD from KBUILD_CFLAGS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 PTI fixes from Ingo Molnar:
"Two fixes: a relatively simple objtool fix that makes Clang built
kernels work with ORC debug info, plus an alternatives macro fix"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/alternatives: Fixup alternative_call_2
objtool: Add Clang support
|
|
Cannon Lake supports C1/C3/C6/C7, PC2/PC3/PC6/PC7/PC8/PC9/PC10
state residency counters, this patch enables those counters.
( The MSR information is based on Intel Software Developers' Manual,
Vol. 4, Order No. 335592. )
Tested-by: Puthikorn Voravootivat <puthik@chromium.org>
Signed-off-by: Harry Pan <harry.pan@intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan.liang@intel.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: gs0622@gmail.com
Link: http://lkml.kernel.org/r/20180309121549.630-3-harry.pan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch enables RAPL counters (energy consumption counters)
support for Cannon Lake processors.
( ESU and power domains refer to Intel Software Developers' Manual,
Vol. 4, Order No. 335592. )
Usage example:
$ perf list
$ perf stat -a -e power/energy-cores/,power/energy-pkg/ sleep 10
Tested-by: Puthikorn Voravootivat <puthik@chromium.org>
Signed-off-by: Harry Pan <harry.pan@intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: colin.king@canonical.com
Cc: gs0622@gmail.com
Cc: kan.liang@linux.intel.com
Link: http://lkml.kernel.org/r/20180309121549.630-2-harry.pan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This issue happens on new ASUS laptop UX331UA which has modern
standby mode (suspend-to-idle). Pressing keys on the PS2 keyboard
can't wake up the system from suspend-to-idle which is not expected.
However, pressing power button can wake up without problem.
Per the engineers of ASUS, the keypress event is routed to Embedded
Controller (EC) in standby mode. EC then signals the SCI event to
BIOS so BIOS would Notify() power button to wake up the system. It's
from BIOS perspective. What we observe here is that kernel receives
the SCI event from SCI interrupt handler which informs that the GPE
status bit belongs to EC needs to be handled and then queries the EC
to find out what event is pending. Then execute the following ACPI
_QDF method which defined in ACPI DSDT for EC to notify power button.
Method (_QDF, 0, NotSerialized) // _Qxx: EC Query
{
Notify (PWRB, 0x80) // Status Change
}
With more debug messages added to analyze this problem, we find that
the keypress does wake up the system from suspend-to-idle but it's back
to suspend again almost immediately. As we see in the following messages,
the acpi_button_notify() is invoked but acpi_pm_wakeup_event() can not
really wake up the system here because acpi_s2idle_wakeup() is false.
The acpi_s2idle_wakeup() returnd false because the acpi_s2idle_sync() has
alrealdy exited.
[ 52.987048] s2idle_loop going s2idle
[ 59.713392] acpi_s2idle_wake enter
[ 59.713394] acpi_s2idle_wake exit
[ 59.760888] acpi_ev_gpe_detect enter
[ 59.760893] acpi_s2idle_sync enter
[ 59.760893] acpi_ec_query_flushed ec pending queries 0
[ 59.760953] Read registers for GPE 50-57: Status=01, Enable=01, RunEnable=01, WakeEnable=00
[ 59.760955] ACPI: EC: ===== IRQ (1) =====
[ 59.760972] ACPI: EC: EC_SC(R) = 0x28 SCI_EVT=1 BURST=0 CMD=1 IBF=0 OBF=0
[ 59.760979] ACPI: EC: +++++ Polling enabled +++++
[ 59.760979] ACPI: EC: ##### Command(QR_EC) submitted/blocked #####
[ 59.761003] acpi_s2idle_sync exit
[ 59.769587] ACPI: EC: ##### Query(0xdf) started #####
[ 59.769611] ACPI: EC: ##### Query(0xdf) stopped #####
[ 59.774154] acpi_button_notify button type 1
[ 59.813175] s2idle_loop going s2idle
acpi_s2idle_sync() already makes an effort to flush the EC event
queue, but in this case, the EC event has yet to be generated when
the call to acpi_ec_flush_work() is made. The event is generated
shortly after, through the ongoing handling of the SCI interrupt
which is happening on another CPU, and we must synchronize that
to make sure that it has run and completed. Adding another call to
acpi_os_wait_events_complete() solves this issue, since that
function synchronizes with SCI interrupt completion.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Trivial fix to spelling mistake in the pr_err_once() error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-janitors@vger.kernel.org
Link: http://lkml.kernel.org/r/20180313154709.1015-1-colin.king@canonical.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Some .<target>.cmd files under arch/x86 are showing two instances of
-D__KERNEL__, like arch/x86/boot/ and arch/x86/realmode/rm/.
__KERNEL__ is already defined in KBUILD_CPPFLAGS in the top Makefile,
so it can be dropped safely.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kbuild@vger.kernel.org
Link: http://lkml.kernel.org/r/20180316084944.3997-1-caoj.fnst@cn.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Two config options in the lock debugging menu that are probably the most
frequently used, as far as I am concerned, is the PROVE_LOCKING and
LOCK_STAT. From a UI perspective, they should be front and center. So
these two options are now moved to the top of the lock debugging menu.
The DEBUG_WW_MUTEX_SLOWPATH option is also added to the PROVE_LOCKING
umbrella.
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1522445280-7767-4-git-send-email-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There are a couples of lock debugging Kconfig options that depends on
the following support options:
- TRACE_IRQFLAGS_SUPPORT
- STACKTRACE_SUPPORT
- LOCKDEP_SUPPORT
That makes those lock debugging options harder to read and understand.
So a new LOCK_DEBUGGING_SUPPORT option is added that is equivalent to
the above three options together. That makes the Kconfig.debug file
more readable.
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1522445280-7767-3-git-send-email-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
For a rwsem, locking can either be exclusive or shared. The corresponding
exclusive or shared unlock must be used. Otherwise, the protected data
structures may get corrupted or the lock may be in an inconsistent state.
In order to detect such anomaly, a new configuration option DEBUG_RWSEMS
is added which can be enabled to look for such mismatches and print
warnings that that happens.
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1522445280-7767-2-git-send-email-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- fix missed rebuild of TRIM_UNUSED_KSYMS
- fix rpm-pkg for GNU tar >= 1.29
- include scripts/dtc/include-prefixes/* to kernel header deb-pkg
- add -no-integrated-as option ealier to fix building with Clang
- fix netfilter Makefile for parallel building
* tag 'kbuild-fixes-v4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
netfilter: nf_nat_snmp_basic: add correct dependency to Makefile
kbuild: rpm-pkg: Support GNU tar >= 1.29
builddeb: Fix header package regarding dtc source links
kbuild: set no-integrated-as before incl. arch Makefile
kbuild: make scripts/adjust_autoksyms.sh robust against timestamp races
|
|
Pull networking fixes from David Miller:
1) Fix RCU locking in xfrm_local_error(), from Taehee Yoo.
2) Fix return value assignments and thus error checking in
iwl_mvm_start_ap_ibss(), from Johannes Berg.
3) Don't count header length twice in vti4, from Stefano Brivio.
4) Fix deadlock in rt6_age_examine_exception, from Eric Dumazet.
5) Fix out-of-bounds access in nf_sk_lookup_slow{v4,v6}() from Subash
Abhinov.
6) Check nladdr size in netlink_connect(), from Alexander Potapenko.
7) VF representor SQ numbers are 32 not 16 bits, in mlx5 driver, from
Or Gerlitz.
8) Out of bounds read in skb_network_protocol(), from Eric Dumazet.
9) r8169 driver sets driver data pointer after register_netdev() which
is too late. Fix from Heiner Kallweit.
10) Fix memory leak in mlx4 driver, from Moshe Shemesh.
11) The multi-VLAN decap fix added a regression when dealing with device
that lack a MAC header, such as tun. Fix from Toshiaki Makita.
12) Fix integer overflow in dynamic interrupt coalescing code. From Tal
Gilboa.
13) Use after free in vrf code, from David Ahern.
14) IPV6 route leak between VRFs fix, also from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: mvneta: fix enable of all initialized RXQs
net/ipv6: Fix route leaking between VRFs
vrf: Fix use after free and double free in vrf_finish_output
ipv6: sr: fix seg6 encap performances with TSO enabled
net/dim: Fix int overflow
vlan: Fix vlan insertion for packets without ethernet header
net: Fix untag for vlan packets without ethernet header
atm: iphase: fix spelling mistake: "Receiverd" -> "Received"
vhost: validate log when IOTLB is enabled
qede: Do not drop rx-checksum invalidated packets.
hv_netvsc: enable multicast if necessary
ip_tunnel: Resolve ipsec merge conflict properly.
lan78xx: Crash in lan78xx_writ_reg (Workqueue: events lan78xx_deferred_multicast_write)
qede: Fix barrier usage after tx doorbell write.
vhost: correctly remove wait queue during poll failure
net/mlx4_core: Fix memory leak while delete slave's resources
net/mlx4_en: Fix mixed PFC and Global pause user control requests
net/smc: use announced length in sock_recvmsg()
llc: properly handle dev_queue_xmit() return value
strparser: Fix sign of err codes
...
|
|
Since commit 28128c61e08e ("kconfig.h: Include compiler types to avoid
missed struct attributes"), <linux/kconfig.h> pulls in kernel-space
headers to unrelated places.
Commit 0f9da844d877 ("MIPS: boot: Define __ASSEMBLY__ for its.S build")
suppress the build error by defining __ASSEMBLY__, but ITS (i.e. DTS)
is not assembly, and should not include <linux/compiler_types.h> in the
first place.
Looking at arch/s390/tools/Makefile, host programs gen_facilities and
gen_opcode_table now pull in <linux/compiler_types.h> as well.
The motivation for that commit was to define necessary attributes
before any struct is defined. Obviously, this happens only in C.
It is enough to include <linux/compiler_types.h> only when compiling
C files, and only when compiling kernel space. Move the include to
c_flags.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
