| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Issue: When the disks are getting discovered and assigned device
handles by the kernel, a device block followed by an unblock
(due to broadcast primitives) issued by the driver is
interspersed by the kernel changing the state of the device.
Therefore the unblock by the driver results in a no operation
within the kernel API.
To fix this one, the below patch checks the return of the unblock API
and performs a block followed by an unblock to unfreeze the block
layer's I/O queue. Sufficient checks and prints are also added in the
driver to identify this condition caused by the kernel.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
dma_map_single() API
Added dma_mapping_error() API after mapping an address with dma_map_single()
API. Otherwise when CONFIG_DMA_API_DEBUG is enabled in the kernel, then it
complains about mpt3sas driver not calling dma_mapping_error after mapping an
address with dma_map_single
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
create_singlethread_workqueue() API
Created a thread using alloc_ordered_workqueue() API in order to process
the works from firmware Work-queue sequentially instead of
create_singlethread_workqueue() API.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
"VendorID" "DeviceID" "SubsystemVendor ID" "SubsystemDevice ID" Cisco Branding String
0x1000 0x97 0x1137 0x154 Cisco 9300-8i 12Gbps SAS HBA
0x1000 0x97 0x1137 0x155 Cisco 12G Modular SAS Pass through Controller
0x1000 0x97 0x1137 0x156 UCS C3X60 12G SAS Pass through Controller
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
gather list fails for a SCSI command
scsi_dma_map API will return a negative value (i.e. -ENOMEM)
if DMA mapping of sg lists fails and zero if the sg list in the
SCSI cmd is NULL. But drivers doesn't handled sg list DMA mapping
failure case properly.
So, Updated the code to return host busy error status to SCSI MID Layer(SML),
when DMA mapping of scatter gather list fails for a SCSI command.
So that SML will retry this SCSI cmd after some time.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
0x0x32010081
For any SCSI command, if the driver receives
IOC status = SCSI_IOC_TERMINATED and log info = 0x32010081 then
that command will be completed with DID_RESET host status.
The definition of this log info value is
"Virtual IO has failed and has to be retried".
Firmware will provide this log info value with IOC Status
"SCSI_IOC_TERMINATED", whenever a drive (with is a part of a volume)
is pulled and pushed back within some minimal delay.
With this log info value, firmware informs the driver to retry the
failed IO command infinite times, so to provide some time for the
firmware to discover the reinserted drive successfully instated of
just retrying failed command for five times(doesn't giving enough
time for firmware to complete the drive discovery) and failing the
IO permanently even though drive came back successfully.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Below are the new changes to MPI 2.5 Rev K(2.5.6) specification and 2.00.35
header files
1) Added a minimum size requirement for target mode command buffers.
2) Added MinMSIxIndex and MaxMSIxIndex fields to CommandBufferPostBase
Request.
3) For BIOS Page 1, added SSUTimeout field, and added Product Name String
Format bits to the BiosOptions field
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Add the following OEM's branding to the mpt3sas driver.
"VendorID" "DeviceID" "SubsystemVendor ID" "SubsystemDevice ID" Cisco Branding String
0x1000 0x97 SVID = 0x1137 0x014C Cisco 9300-8E 12G SAS HBA
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Added the following Dell branding to the mpt3sas driver.
"VendorID" "DeviceID" "SubsystemVendor ID" "SubsystemDevice ID" Dell Branding String
0x1000 0x0097 0x1028 0x1F46 DELL 12Gbps HBA
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Following is the change set,
1. Added more defines for the BiosOptions field of MPI2_CONFIG_PAGE_BIOS_1.
2. Added MPI2_TOOLBOX_CLEAN_BIT26_PRODUCT_SPECIFIC definition.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
This Patch will provide more details of the devices such as slot number,
enclosure logical id, enclosure level & connector name in the following
scenarios,
- When end device is added in the topology,
- When the end device is removed from the setup,
- When the SCSI mid layer issues TASK ABORT/ DEVICE RESET/ TARGET RESET during
error handling,
- When any command to the device fails with Sense key Hardware error or Medium
error or Unit Attention,
- When firmware returns device error or device not ready status for the end
device,
- When a Predicted fault is detected on an end device.
This information can be used by the user to identify the location of the
desired drive in the topology.
Driver will get these information by reading the sas device page0.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Update MPI 2.5 Release: MPI 2.5 Rev I (2.5.4) specification and 2.00.33 header
files
Below is the change set from the MPI specification for I Rev
1) Added Base Enclosure Level bit to the Flags field of Manufacturing Page 7.
2) Updated description of the MaxTargetPortConnectTime field of SAS IO Unit
Page 1.
3) Added EnclosureLevel and ConnectorName fields to SAS Device Page 0. Also,
added EnclosureLevel and ConnectorName Valid bit to the Flags field.
4) Added EnclosureLevel field to SAS Enclosure Page 0. Also, added
EnclosureLevel Valid bit to the Flags field.
5) Added value for BIOS image to HashImageType.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
During hot-plugging of a disk(having a flaky link), the disk addition
stops and any further disk addition or removal doesn't happen on that
controller.
This is because, when driver receives DELAY_NOT_RESPONDING event for a disk
while it is undergoing addition at the SCSI Transport layer, the driver
would block the I/O to that disk resulting in a deadlock. i.e the disk
addition work couldn't be completed at the SCSI Transport Layer as it
can't send any I/Os (such as Inquiry, Report LUNs etc) to the disk as
I/Os are blocked to this drive. Also any subsequent device removal
(TARGET_NOT_RESPONDING) or link update(RC_PHY_CHANGED) event couldn't be
processed as they are in the queue to get processed after disk addition
event.
Description of Change:
Don't block the drive when drive addition is under the control of SML.
So that SML won't be blocked of issuing the device dicovery commands
(such as Inquiry, Report LUNs etc).
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
card gets into READY or Operational state.
Driver initialization fails if driver tries to send IOC facts request message
when the IOC is in reset or in a fault state.
This patch will make sure that
1.Driver to send IOC facts request message only if HBA is in operational or
ready state.
2.If IOC is in fault state, a diagnostic reset would be issued.
3.If IOC is in reset state then driver will wait for 10 seconds to exit out
of reset state. If the HBA continues to be in reset state, then the HBA
wouldn't be claimed by the driver.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
support
In this patch, increased the number of MSIX vector support for SAS3 C0 HBAs to
up-to 96.
Following are changes that are done in this patch
1. This feature is enabled only for SAS3 C0 and higher revision cards and also
only when reply post free queue count is greater than 8.
2. To support this feature 12 SupplementalReplyPostHostIndex system interfaces
are used. MSI-X index numbered from 0 to 7 use the first
SupplementalReplyPostHostIndex system interface to update its corresponding
ReplyPostHostIndex values, MSI-X index numbered from 8 to 15 will use the
second SupplementalReplyPostHostIndex system interface and so on. These 12
SuppementalReplyPostHostIndex system interfaces address are saved in the array
replyPostRegisterIndex[].
3. As each SupplementalReplyPostHostIndex register supports 8 MSI-X
vectors. So MSIxIndex field in these register must contain a value between 0
and 7.
4. After processing the reply descriptors from a reply post free queues then
update the new reply post host index value in ReplyPostHostIndex field and
(msix_index mod 8) value in MSIxIndex field of SupplementalReplyPostHostIndex
register. The Address of this SupplementalReplyPostHostIndex register is
retrived from (msix_index/8)th entry of replyPostRegisterIndex[] array.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
LPSS devices in Braswell does not need the default 10ms
d3_delay imposed by PCI specification. Removing this
unnecessary delay significantly reduces the resume time
approximately upto 200ms on this platform.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add support for the InvenSense ICS-43432 I2S MEMS microphone.
This is a non-software-configurable MEMS microphone with I2S output.
Tested on a setup with a single ICS-43432 (the device itself supports
stereo operation using a hardware pin controlling left vs. right channel
output).
Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
These particular opcode names are not used in the kernel directly,
so updating them just has the effect of making downstream consumers
more likely to end up using better names; this was reported from the
qemu community.
Reported-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
|
|
When injecting a fault into a misbehaving 32bit guest, it seems
rather idiotic to also inject a 64bit fault that is only going
to corrupt the guest state. This leads to a situation where we
perform an illegal exception return at EL2 causing the host
to crash instead of killing the guest.
Just fix the stupid bug that has been there from day 1.
Cc: <stable@vger.kernel.org>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Commit 0a4377de3056 ("genirq: Introduce irq_set_vcpu_affinity() to
target an interrupt to a VCPU") added just what we needed at the
lowest level to allow an interrupt to be deactivated by a guest.
When such a request reaches the GIC, it knows it doesn't need to
perform the deactivation anymore, and can safely leave the guest
do its magic. This of course requires additional support in both
VFIO and KVM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Eric Auger <eric.auger@linaro.org>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: kvmarm@lists.cs.columbia.edu
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1440604845-28229-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
So far, GICv2 has been used with EOImode == 0. The effect of this
mode is to perform the priority drop and the deactivation of the
interrupt at the same time.
While this works perfectly for Linux (we only have a single priority),
it causes issues when an interrupt is forwarded to a guest, and when
we want the guest to perform the EOI itself.
For this case, the GIC architecture provides EOImode == 1, where:
- A write to the EOI register drops the priority of the interrupt
and leaves it active. Other interrupts at the same priority level
can now be taken, but the active interrupt cannot be taken again
- A write to the DIR marks the interrupt as inactive, meaning it can
now be taken again.
We only enable this feature when booted in HYP mode and that
the device-tree reported a suitable CPU interface. Observable behaviour
should remain unchanged.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Eric Auger <eric.auger@linaro.org>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: kvmarm@lists.cs.columbia.edu
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1440604845-28229-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Commit 0a4377de3056 ("genirq: Introduce irq_set_vcpu_affinity() to
target an interrupt to a VCPU") added just what we needed at the
lowest level to allow an interrupt to be deactivated by a guest.
When such a request reaches the GIC, it knows it doesn't need to
perform the deactivation anymore, and can safely leave the guest
do its magic. This of course requires additional support in both
VFIO and KVM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Eric Auger <eric.auger@linaro.org>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: kvmarm@lists.cs.columbia.edu
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1440604845-28229-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
So far, GICv3 has been used in with EOImode == 0. The effect of this
mode is to perform the priority drop and the deactivation of the
interrupt at the same time.
While this works perfectly for Linux (we only have a single priority),
it causes issues when an interrupt is forwarded to a guest, and when
we want the guest to perform the EOI itself.
For this case, the GIC architecture provides EOImode == 1, where:
- A write to ICC_EOIR1_EL1 drops the priority of the interrupt and
leaves it active. Other interrupts at the same priority level can
now be taken, but the active interrupt cannot be taken again
- A write to ICC_DIR_EL1 marks the interrupt as inactive, meaning
it can now be taken again.
This patch converts the driver to be able to use this new mode,
depending on whether or not the kernel can behave as a hypervisor.
No feature change.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Eric Auger <eric.auger@linaro.org>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: kvmarm@lists.cs.columbia.edu
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1440604845-28229-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This patch adds a member (cpu_pwr_sample_ratio) of fam15h_power_data,
that represents the ratio of compute unit power accumulator sample
period to the PTSC counter period.
Tsample: compute unit power accumulator sample period
Tref: the performance timestamp counter period
PTSC: performance timestamp counter
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch updates description of fam15h_power driver, its scope is
extended to family 16h processsors.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
On Carrizo and later platforms, running_avg_capture bit field is
extended to 4:31 (28 bits) from 4:25.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Print a dlm-specific error when a socket error occurs
when sending a dlm message.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
|
|
We rename fam15h_power_is_internal_node0() function to
should_load_on_this_node(), because it may not be node0 from KV and
on, and they are single-node processors.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
AMD Carrizo(Fam15h, M60h) processors can report power1_crit
(ProcessorPwrWatts) and power1_input (CurrPwrWatts) values.
And this patch adds support for CZ.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Now that support for platforms which have optional regulator is added,
remove CONFIG_REGULATOR check in omap_hsmmc.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
vdd voltage is set in mmc core to ios->vdd and vmmc should actually
be set to this voltage. Modify omap_hsmmc_enable_supply
to not take vdd as argument since now it's directly set to
the voltage in ios->vdd.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use regulator_is_enabled of pbias regulator to find pbias regulator
status instead of maintaining a custom bookkeeping
pbias_enabled variable.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
enable vmmc_aux regulator only if it is in disabled state and disable
vmmc_aux regulator only if it is in enabled state.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If the regulator is enabled on boot (checked using regulator_is_enabled),
invoke regulator_enable() so that the usecount reflects the correct
state of the regulator and then disable the regulator so that the
initial state of the regulator is disabled. Avoid using ->set_power,
since set_power also takes care of setting the voltages which is not
needed at this point.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fix omap_hsmmc_set_power so that pbias regulator is not enabled
during power off.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
No functional change. Cleanup omap_hsmmc_set_power by adding separate
functions to set pbias and invoke it from omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
No functional change. Cleanup omap_hsmmc_set_power by adding separate
functions for enable/disable supply and invoke it from
omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Return error if any of the regulator APIs (regulator_enable,
regulator_disable, regulator_set_voltage) fails in
omap_hsmmc_set_power to avoid undefined behavior.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Remove the unnecessary pbias regulator_set_voltage done after
pbias regulator_disable in omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
No functional change. Instead of using omap_hsmmc_host's vcc and vcc_aux
members, use vmmc and vqmmc present in mmc_host which is present
for the same purpose.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If the vmmc regulator provides a valid ocrmask, use it. By this even if
the pdata has a valid ocrmask, it will be overwritten with the ocrmask
of the vmmc regulator.
Also remove the unnecessary compatibility check between the ocrmask in
the pdata and the ocrmask from the vmmc regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
No functional change. Instead of using a local regulator variable
in omap_hsmmc_reg_get() for holding the return value of
devm_regulator_get_optional() and then assigning to omap_hsmmc_host
regulator members: vcc, vcc_aux and pbias, directly use the
omap_hsmmc_host regulator members.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Now return error only if the return value of
devm_regulator_get_optional() is not the same as -ENODEV, since with
-EPROBE_DEFER, the regulator can be obtained later and all other
errors are fatal.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since vmmc can be optional for some platforms, use
devm_regulator_get_optional() for vmmc. Now return error only
if the return value of devm_regulator_get_optional() is not the
same as -ENODEV, since with -EPROBE_DEFER, the regulator can be
obtained later and all other errors are fatal.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: ludovic.desroches@atmel.com <ludovic.desroches@atmel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
