| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into gpio/next
|
|
This patch fix the problem with rootfs on JFFS2 with early printk
console turned on.
The origin version used TLB63 for temporary early printk mapping.
The code expect that kernel is not able to use all 64 TLB entries
till early printk console is remapped by ioremap. After that
temporary mapping on TLB63 is silently lost.
This expectation give the opportunity to have early console pretty
early.
Microblaze systems with JFFS2 rootfs with early printk console turned on
used more than 64 TLB entries before kernel can remap early console.
Based on that kernel does access to bad area because early printk mapping
is rewritten.
This patch introduces tlb_skip variable which dynamically stores number
of skipped TLB entries from the TLB0. skip_tlb=2 means that TLB0 and TLB1
should be skipped.
MICROBLAZE_TLB_SKIP defines how many TLB is skipped at the kernel start.
They can be used for user purpose.
TLB 63 is used for temporary LMB mapping (MICROBLAZE_LMB_TLB_ID).
Also clean TLBLO when kernel starts.
For specific kernel sizes kernel can use just one TLB. Detect this case
and use the second TLB for general purpose.
Change _tlbia function to flush TLB entries from tlb_skip to TLB_SIZE.
Export tlb_skip size through debugfs.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
TLB skip size direct how many TLBs is skipped.
Currently TLB0 and TLB1 are used for Linux kernel mapping
that's why their are skipped.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Systems with small amount of memory need to be handled
differently. Linux can't allocate the whole 32MB with two TLBs
because then there is no MMU protection.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
The main reason is bug because of dynamic TLB allocation.
U-BOOT didn't disable dcache and then writing to physical address
from ASM wan't visible for reading through MMU.
Disabling caches and clearing all flags from previous code
is good to do so.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Change report in bootlog:
Origin:
xlnx,xps-intc-1.00.a #0 at 0xc8000000, num_irq=6, edge=0x4
xlnx,xps-timer-1.00.a #0 at 0xc8004000, irq=2
New:
interrupt-controller #0 at 0xc8000000, num_irq=6, edge=0x4
system-timer #0 at 0xc8004000, irq=2
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Fix how many pages are allocated in mapin_ram. It is lowmem_size
not setup CONFIG_LOWMEM_SIZE because it is the same for all systems.
Which means that wrong pages are allocated if memory size is smaller
than CONFIG_LOWMEM_SIZE. It has dramatic impact on bootup time.
On sp605 MMU full hw design is 7s.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
The first highmem implementation.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Register lowmem active regions.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Microblaze MMU is similar to ppc that's why ppc layout
was reused.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Fixmap will be used for highmem support.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Use CONFIG_LOWMEM_SIZE if system has larger ram size.
For system with larger ram size, enable HIGMEM support.
Also setup limitation for memblock and use memblock
allocation in lowmem region.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
We should use ZONE_DMA because all address space is dma-able.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Pull fbdev updates for 3.4 from Florian Tobias Schandinat:
- drivers for Samsung Exynos MIPI DSI and display port
- i740fb to support those old Intel chips
- large updates to OMAP, viafb and sh_mobile_lcdcfb
- some updates to s3c-fb and udlfb, few patches to others
Fix up conflicts in drivers/video/udlfb.c due to Key Sievers' fix making
it in twice.
* tag 'fbdev-updates-for-3.4' of git://github.com/schandinat/linux-2.6: (156 commits)
Revert "video:uvesafb: Fix oops that uvesafb try to execute NX-protected page"
OMAPDSS: register dss drivers in module init
video: pxafb: add clk_prepare/clk_unprepare calls
fbdev: bfin_adv7393fb: Drop needless include
fbdev: sh_mipi_dsi: add extra phyctrl for sh_mipi_dsi_info
fbdev: remove dependency of FB_SH_MOBILE_MERAM from FB_SH_MOBILE_LCDC
Revert "MAINTAINERS: add entry for exynos mipi display drivers"
fbdev: da8xx: add support for SP10Q010 display
fbdev: da8xx:: fix reporting of the display timing info
drivers/video/pvr2fb.c: ensure arguments to request_irq and free_irq are compatible
OMAPDSS: APPLY: fix clearing shadow dirty flag with manual update
fbdev: sh_mobile_meram: Implement system suspend/resume
fbdev: sh_mobile_meram: Remove unneeded sanity checks
fbdev: sh_mobile_meram: Don't perform update in register operation
arm: mach-shmobile: Constify sh_mobile_meram_cfg structures
fbdev: sh_mobile_lcdc: Don't store copy of platform data
fbdev: sh_mobile_meram: Remove unused sh_mobile_meram_icb_cfg fields
arm: mach-shmobile: Don't set MERAM ICB numbers in platform data
fbdev: sh_mobile_meram: Allocate ICBs automatically
fbdev: sh_mobile_meram: Use genalloc to manage MERAM allocation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Things are really quieting down with the regmap API, while we're still
seeing a trickle of new features coming in they're getting much
smaller than they were. It's also nice to have some features which
support other subsystems building infrastructure on top of regmap.
Highlights include:
- Support for padding between the register and the value when
interacting with the device, sometimes needed for fast interfaces.
- Support for applying register updates to the device when restoring
the register state. This is intended to be used to apply updates
supplied by manufacturers for tuning the performance of the device
(many of which are to undocumented registers which aren't otherwise
covered).
- Support for multi-register operations on cached registers.
- Support for syncing only part of the register cache.
- Stubs and parameter query functions intended to make it easier for
other subsystems to build infrastructure on top of the regmap API.
plus a few driver updates making use of the new features which it was
easier to merge via this tree."
* tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (41 commits)
regmap: Fix future missing prototype of devres_alloc() and friends
regmap: Rejig struct declarations for stubbed API
regmap: Fix rbtree block base in sync
regcache: Make sure we sync register 0 in an rbtree cache
regmap: delete unused module.h from drivers/base/regmap files
regmap: Add stub for regcache_sync_region()
mfd: Improve performance of later WM1811 revisions
regmap: Fix x86_64 breakage
regmap: Allow drivers to sync only part of the register cache
regmap: Supply ranges to the sync operations
regmap: Add tracepoints for cache only and cache bypass
regmap: Mark the cache as clean after a successful sync
regmap: Remove default cache sync implementation
regmap: Skip hardware defaults for LZO caches
regmap: Expose the driver name in debugfs
mfd: wm8400: Convert to devm_regmap_init_i2c()
mfd: wm831x: Convert to devm_regmap_init()
mfd: wm8994: Convert to devm_regmap_init()
mfd/ASoC: Convert WM8994 driver to use regmap patches
mfd: Add __devinit and __devexit annotations in wm8994
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull IEEE 1394 (FireWire) subsystem updates post v3.3 from Stefan Richter:
- Some SBP-2 initiator fixes, side product from ongoing work on a target.
- Reintroduction of an isochronous I/O feature of the older ieee1394 driver
stack (flush buffer completions); it was evidently rarely used but not
actually unused. Matching libraw1394 code is already available.
- Be sure to prefix all kernel log messages with device name or card name,
and other logging related cleanups.
- Misc other small cleanups, among them a small API change that affects
sound/firewire/ too. Clemens Ladisch is aware of it.
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394: (26 commits)
firewire: allow explicit flushing of iso packet completions
firewire: prevent dropping of completed iso packet header data
firewire: ohci: factor out iso completion flushing code
firewire: ohci: simplify iso header pointer arithmetic
firewire: ohci: optimize control bit checks
firewire: ohci: remove unused excess_bytes field
firewire: ohci: copy_iso_headers(): make comment match the code
firewire: cdev: fix IR multichannel event documentation
firewire: ohci: fix too-early completion of IR multichannel buffers
firewire: ohci: move runtime debug facility out of #ifdef
firewire: tone down some diagnostic log messages
firewire: sbp2: replace a GFP_ATOMIC allocation
firewire: sbp2: Fix SCSI sense data mangling
firewire: sbp2: Ignore SBP-2 targets on the local node
firewire: sbp2: Take into account Unit_Unique_ID
firewire: nosy: Use the macro DMA_BIT_MASK().
firewire: core: convert AR-req handler lock from _irqsave to _bh
firewire: core: fix race at address_handler unregistration
firewire: core: remove obsolete comment
firewire: core: prefix log messages with card name
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates for v3.4 from Linus Walleij (*):
- Switches the PXA 168, 910 and MMP over to use pinctrl
- Locking revamped
- Massive refactorings...
- Reform the driver API to use multiple states
- Support pin config in the mapping tables
- Pinctrl drivers for the nVidia Tegra series
- Generic pin config support lib for simple pin controllers
- Implement pin config for the U300
* tag 'pinctrl-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
ARM: u300: configure some pins as an example
pinctrl: support pinconfig on the U300
pinctrl/coh901: use generic pinconf enums and parameters
pinctrl: introduce generic pin config
pinctrl: fix error path in pinconf_map_to_setting()
pinctrl: allow concurrent gpio and mux function ownership of pins
pinctrl: forward-declare struct device
pinctrl: split pincontrol states into its own header
pinctrl: include machine header to core.h
ARM: tegra: Select PINCTRL Kconfig variables
pinctrl: add a driver for NVIDIA Tegra
pinctrl: Show selected function and group in pinmux-pins debugfs
pinctrl: enhance mapping table to support pin config operations
pinctrl: API changes to support multiple states per device
pinctrl: add usecount to pins for muxing
pinctrl: refactor struct pinctrl handling in core.c vs pinmux.c
pinctrl: fix and simplify locking
pinctrl: fix the pin descriptor kerneldoc
pinctrl: assume map table entries can't have a NULL name field
pinctrl: introduce PINCTRL_STATE_DEFAULT, define hogs as that state
...
(*) What is it with all these Linuses these days? There's a Linus at
google too. Some day I will get myself my own broadsword, and run
around screaming "There can be only one".
I used to be _special_ dammit. Snif.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata updates from Jeff Garzik:
1) AHCI regression fix. A recent "make driver conform to spec" change
broke on deployed hardware. Make new behavior optional, rather than
default, turning it on only for specific embedded platforms that
need this.
Everybody else runs in the famous "non conformant but working" mode.
2) pata_cmd64x, pata_legacy cleanups
3) new Intel SATA PCI IDs
4) misc minor vendor feature additions
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_cmd64x: implement sff_irq_check() method
pata_cmd64x: implement sff_irq_clear() method
pata_cmd64x: use interrupt status from MRDMODE register
pata_cmd64x: turn string of *if* statements into *switch*
drivers/ata/pata_mpc52xx.c: clean up error handling code
ahci_platform: add STRICT_AHCI platform type
ahci: move AHCI_HFLAGS() macro to ahci.h
ahci: add AHCI_HFLAG_DELAY_ENGINE host flag
sata_fsl: add support for interrupt coalsecing feature
ata/pata_arasan_cf: Add Hibernation support
pata_legacy: correctly mask recovery field for HT6560B
ata_piix: IDE-mode SATA patch for Intel Lynx Point DeviceIDs
ahci: AHCI-mode SATA patch for Intel Lynx Point DeviceIDs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov:
"- we finally merged driver for USB version of Synaptics touchpads
(I guess most commonly found in IBM/Lenovo keyboard/touchpad combo);
- a bunch of new drivers for embedded platforms (Cypress
touchscreens, DA9052 OnKey, MAX8997-haptic, Ilitek ILI210x
touchscreens, TI touchscreen);
- input core allows clients to specify desired clock source for
timestamps on input events (EVIOCSCLOCKID ioctl);
- input core allows querying state of all MT slots for given event
code via EVIOCGMTSLOTS ioctl;
- various driver fixes and improvements."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: ili210x - add support for Ilitek ILI210x based touchscreens
Input: altera_ps2 - use of_match_ptr()
Input: synaptics_usb - switch to module_usb_driver()
Input: convert I2C drivers to use module_i2c_driver()
Input: convert SPI drivers to use module_spi_driver()
Input: omap4-keypad - move platform_data to <linux/platform_data>
Input: kxtj9 - who_am_i check value and initial data rate fixes
Input: add driver support for MAX8997-haptic
Input: tegra-kbc - revise device tree support
Input: of_keymap - add device tree bindings for simple key matrices
Input: wacom - fix physical size calculation for 3rd-gen Bamboo
Input: twl4030-vibra - really switch from #if to #ifdef
Input: hp680_ts_input - ensure arguments to request_irq and free_irq are compatible
Input: max8925_onkey - avoid accessing input device too early
Input: max8925_onkey - allow to be used as a wakeup source
Input: atmel-wm97xx - convert to dev_pm_ops
Input: atmel-wm97xx - set driver owner
Input: add cyttsp touchscreen maintainer entry
Input: cyttsp - remove useless checks in cyttsp_probe()
Input: usbtouchscreen - add support for Data Modul EasyTouch TP 72037
...
|
|
Pull crypto fixes from Herbert Xu:
"This fixes a build problem where two crypto modules both try to export
the same symbols (which shouldn't have been exported in the first
place)."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: twofish-x86_64-3way - module init/exit functions should be static
crypto: camellia-x86_64 - module init/exit functions should be static
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen updates from Konrad Rzeszutek Wilk:
"which has three neat features:
- PV multiconsole support, so that there can be hvc1, hvc2, etc; This
can be used in HVM and in PV mode.
- P-state and C-state power management driver that uploads said power
management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
There is one thing in the Kconfig that you won't like: "default y
if (X86_ACPI_CPUFREQ = y || X86_POWERNOW_K8 = y)" (note, that it
all depends on CONFIG_XEN which depends on CONFIG_PARAVIRT which by
default is off). I've a fix to convert that boolean expression
into "default m" which I am going to post after the cpufreq git
pull - as the two patches to make this work depend on a fix in Dave
Jones's tree.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx"
Fix up trivial conflicts in drivers/tty/hvc/hvc_xen.c due to changes to
a removed commit.
* tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen kconfig: relax INPUT_XEN_KBDDEV_FRONTEND deps
xen/acpi-processor: C and P-state driver that uploads said data to hypervisor.
xen: constify all instances of "struct attribute_group"
xen/xenbus: ignore console/0
hvc_xen: introduce HVC_XEN_FRONTEND
hvc_xen: implement multiconsole support
hvc_xen: support PV on HVM consoles
xenbus: don't free other end details too early
xen/enlighten: Expose MWAIT and MWAIT_LEAF if hypervisor OKs it.
xen/setup/pm/acpi: Remove the call to boot_option_idle_override.
xenbus: address compiler warnings
xen: use this_cpu_xxx replace percpu_xxx funcs
xen/pciback: Support pci_reset_function, aka FLR or D3 support.
pci: Introduce __pci_reset_function_locked to be used when holding device_lock.
xen: Utilize the restore_msi_irqs hook.
|
|
usbnet should centrally handle busy reporting in the rx path
so subdrivers need not worry. This hurts use cases which do
rx only or predominantly.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm
Pull cleancache changes from Konrad Rzeszutek Wilk:
"This has some patches for the cleancache API that should have been
submitted a _long_ time ago. They are basically cleanups:
- rename of flush to invalidate
- moving reporting of statistics into debugfs
- use __read_mostly as necessary.
Oh, and also the MAINTAINERS file change. The files (except the
MAINTAINERS file) have been in #linux-next for months now. The late
addition of MAINTAINERS file is a brain-fart on my side - didn't
realize I needed that just until I was typing this up - and I based
that patch on v3.3 - so the tree is on top of v3.3."
* tag 'stable/for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm:
MAINTAINERS: Adding cleancache API to the list.
mm: cleancache: Use __read_mostly as appropiate.
mm: cleancache: report statistics via debugfs instead of sysfs.
mm: zcache/tmem/cleancache: s/flush/invalidate/
mm: cleancache: s/flush/invalidate/
|
|
The following patch aimed to resolve an issue where secondary, tertiary,
etc. addresses added to bond interfaces could overwrite the
bond->master_ip and vlan_ip values.
commit 917fbdb32f37e9a93b00bb12ee83532982982df3
Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com>
Date: Wed Nov 23 23:37:15 2011 +0000
bonding: only use primary address for ARP
That patch was good because it prevented bonds using ARP monitoring from
sending frames with an invalid source IP address. Unfortunately, it
didn't always work as expected.
When using an ioctl (like ifconfig does) to set the IP address and
netmask, 2 separate ioctls are actually called to set the IP and netmask
if the mask chosen doesn't match the standard mask for that class of
address. The first ioctl did not have a mask that matched the one in
the primary address and would still cause the device address to be
overwritten. The second ioctl that was called to set the mask would
then detect as secondary and ignored, but the damage was already done.
This was not an issue when using an application that used netlink
sockets as the setting of IP and netmask came down at once. The
inconsistent behavior between those two interfaces was something that
needed to be resolved.
While I was thinking about how I wanted to resolve this, Ralf Zeidler
came with a patch that resolved this on a RHEL kernel by keeping a full
shadow of the entries in dev->ifa_list for the bonding device and vlan
devices in the bonding driver. I didn't like the duplication of the
list as I want to see the 'bonding' struct and code shrink rather than
grow, but liked the general idea.
As the Subject indicates this patch drops the master_ip and vlan_ip
elements from the 'bonding' and 'vlan_entry' structs, respectively.
This can be done because a device's address-list is now traversed to
determine the optimal source IP address for ARP requests and for checks
to see if the bonding device has a particular IP address. This code
could have all be contained inside the bonding driver, but it made more
sense to me to EXPORT and call inet_confirm_addr since it did exactly
what was needed.
I tested this and a backported patch and everything works as expected.
Ralf also helped with verification of the backported patch.
Thanks to Ralf for all his help on this.
v2: Whitespace and organizational changes based on suggestions from Jay
Vosburgh and Dave Miller.
v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's
suggestion.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Ralf Zeidler <ralf.zeidler@nsn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It used to be an int, and it got changed to a bool parameter at least
7 years ago. It happens that NF_ACCEPT and NF_DROP are 0 and 1, so
this works, but it's unclear, and the check that it's in range is not
required.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin
Pull blackfin updates from Bob Liu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin: (24 commits)
blackfin: clean up string bfin_dma_5xx after rename.
blackfin:dma: rename bfin_dma_5xx.c to bfin_dma.c
bf548: ssm2602: Add ssm2602 platform data into bf548 ezkit board file.
Blackfin: s/#if CONFIG/#ifdef CONFIG/
Blackfin: pnav: delete duplicate linux/export.h include
bf561: add ppi DLEN macro for 10bits to 16bits
arch: blackfin: udpate defconfig
Disintegrate asm/system.h for Blackfin [ver #2]
arch/blackfin: don't generate random mac in bfin_get_ether_addr()
Blackfin: wire up new process_vm syscalls
blackfin: cleanup anomaly workarounds
blackfin: update default defconfig
blackfin: thread_info: add suspend flag
bfin: add bfin_ad73311_machine platform device
blackfin: bf537: stamp: update board file for 193x
blackfin: kgdb: skip hardware watchpoint test
bf548: add ppi interrupt mask and blanking clocks
blackfin: bf561: forgot CSYNC in get_core_lock_noflush
spi/bfin_spi: drop bits_per_word from client data
blackfin: cplb-mpu: fix page mask table overflow
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"The biggest patch is the rework of the smp code, something I wanted to
do for some time. There are some patches for our various dump methods
and one new thing: z/VM LGR detection. LGR stands for linux-guest-
relocation and is the guest migration feature of z/VM. For debugging
purposes we keep a log of the systems where a specific guest has lived."
Fix up trivial conflict in arch/s390/kernel/smp.c due to the scheduler
cleanup having removed some code next to removed s390 code.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
[S390] kernel: Pass correct stack for smp_call_ipl_cpu()
[S390] Ensure that vmcore_info pointer is never accessed directly
[S390] dasd: prevent validate server for offline devices
[S390] Remove monolithic build option for zcrypt driver.
[S390] stack dump: fix indentation in output
[S390] kernel: Add OS info memory interface
[S390] Use block_sigmask()
[S390] kernel: Add z/VM LGR detection
[S390] irq: external interrupt code passing
[S390] irq: set __ARCH_IRQ_EXIT_IRQS_DISABLED
[S390] zfcpdump: Implement async sdias event processing
[S390] Use copy_to_absolute_zero() instead of "stura/sturg"
[S390] rework idle code
[S390] rework smp code
[S390] rename lowcore field
[S390] Fix gcc 4.6.0 compile warning
|
|
avc_audit() did a lot of jumping around and had a big stack frame, all
for the uncommon case.
Split up the uncommon case (which we really can't make go fast anyway)
into its own slow function, and mark the conditional branches
appropriately for the common likely case.
This causes avc_audit() to no longer show up as one of the hottest
functions on the branch profiles (the new "perf -b" thing), and makes
the cycle profiles look really nice and dense too.
The whole audit path is still annoyingly very much one of the biggest
costs of name lookup, so these things are worth optimizing for. I wish
we could just tell people to turn it off, but realistically we do need
it: we just need to make sure that the overhead of the necessary evil is
as low as possible.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We need to permanently attach the timeout policy to the conntrack,
otherwise we may apply the custom timeout policy inconsistently.
Without this patch, the following example:
nfct timeout add test inet icmp timeout 100
iptables -I PREROUTING -t raw -p icmp -s 1.1.1.1 -j CT --timeout test
Will only apply the custom timeout policy to outgoing packets from
1.1.1.1, but not to reply packets from 2.2.2.2 going to 1.1.1.1.
To fix this issue, this patch modifies the current logic to attach the
timeout policy when the first packet is seen (which is when the
conntrack entry is created). Then, we keep using the attached timeout
policy until the conntrack entry is destroyed.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
`iptables -p all' uses 0 to match all protocols, while the conntrack
subsystem uses 255. We still need `-p all' to attach the custom
timeout policies for the generic protocol tracker.
Moreover, we may use `iptables -p sctp' while the SCTP tracker is
not loaded. In that case, we have to default on the generic protocol
tracker.
Another possibility is `iptables -p ip' that should be supported
as well. This patch makes sure we validate all possible scenarios.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Fix a dereference to pointer without rcu_read_lock held.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch introduces nf_conntrack_l4proto_find_get() and
nf_conntrack_l4proto_put() to fix module dependencies between
timeout objects and l4-protocol conntrack modules.
Thus, we make sure that the module cannot be removed if it is
used by any of the cttimeout objects.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
URB unlinking is always racing with its completion and tx_complete
may be called before or during running usb_unlink_urb, so tx_complete
must not clear urb->dev since it will be used in unlink path,
otherwise invalid memory accesses or usb device leak may be caused
inside usb_unlink_urb.
Cc: stable@kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4231d47e6fe69f061f96c98c30eaf9fb4c14b96d(net/usbnet: avoid
recursive locking in usbnet_stop()) fixes the recursive locking
problem by releasing the skb queue lock, but it makes usb_unlink_urb
racing with defer_bh, and the URB to being unlinked may be freed before
or during calling usb_unlink_urb, so use-after-free problem may be
triggerd inside usb_unlink_urb.
The patch fixes the use-after-free problem by increasing URB
reference count with skb queue lock held before calling
usb_unlink_urb, so the URB won't be freed until return from
usb_unlink_urb.
Cc: stable@kernel.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We call the wrong replay notify function when we use ESN replay
handling. This leads to the fact that we don't send notifications
if we use ESN. Fix this by calling the registered callbacks instead
of xfrm_replay_notify().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The xfrm_state argument is unused in this function, so remove it.
Also the name xfrm_state_check_space does not really match what this
function does. It actually checks if we have enough head and tailroom
on the skb. So we rename the function to xfrm_skb_check_space.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should be using the gfp flags the caller specified here, instead of
GFP_KERNEL. I think this might be a bugfix, depending on the value of
"sock->sk->sk_allocation" when we call rds_conn_create_outgoing() in
rds_sendmsg(). Otherwise, it's just a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function takes a GFP flags as a parameter, but they are never used.
We don't take a lock in this function so there is no reason to prefer
GFP_ATOMIC over the caller's GFP flags.
There is only one caller, cipso_v4_map_cat_rng_ntoh(), and it passes
GFP_ATOMIC as the GFP flags so this doesn't change how the code works.
It's just a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While doing the fs/namei.c cleanups, I ran sparse on it, and it pointed
out other large integers and a couple of cases of us using '0' instead
of the proper 'NULL'.
Sparse still doesn't understand some of the conditional locking going
on, but that's no excuse for not fixing up the trivial stuff.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
According to grep I see no users:
| #git grep inttest
| Documentation/kernel-parameters.txt: inttest= [IA-64]
The parameters itself has no description what it supposed to do.
According to the history tree, it was introduced in "[PATCH] Updated
Documentation/kernel-parameters.txt" ("10414c6ddb"). By that time that
parameter had an user. It was removed later by "[PATCH] ia64: SGI SN
update" ("c6bacd5010ec") by Jesse Barnes himself.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
In commit commit 1de5b41cd3b2 ("fs/namei.c: fix warnings on 32-bit")
Andrew said that there must be a tidier way of doing this.
This is that tidier way.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix kernel-doc warnings in fs/dcache.c:
Warning(fs/dcache.c:1743): No description found for parameter 'seqp'
Warning(fs/dcache.c:1743): Excess function parameter 'seq' description in '__d_lookup_rcu'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We want it to match what hash_name() is doing, which means extra
multiply by 9 in this case...
Reported-and-Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Protect code accessing ctl_table by grabbing the header with grab_header()
and after releasing with sysctl_head_finish(). This is needed if poll()
is called in entries created by modules: currently only hostname and
domainname support poll(), but this bug may be triggered when/if modules
use it and if user called poll() in a file that doesn't support it.
Dave Jones reported the following when using a syscall fuzzer while
hibernating/resuming:
RIP: 0010:[<ffffffff81233e3e>] [<ffffffff81233e3e>] proc_sys_poll+0x4e/0x90
RAX: 0000000000000145 RBX: ffff88020cab6940 RCX: 0000000000000000
RDX: ffffffff81233df0 RSI: 6b6b6b6b6b6b6b6b RDI: ffff88020cab6940
[ ... ]
Code: 00 48 89 fb 48 89 f1 48 8b 40 30 4c 8b 60 e8 b8 45 01 00 00 49 83
7c 24 28 00 74 2e 49 8b 74 24 30 48 85 f6 74 24 48 85 c9 75 32 <8b> 16
b8 45 01 00 00 48 63 d2 49 39 d5 74 10 8b 06 48 98 48 89
If an entry goes away while we are polling() it, ctl_table may not exist
anymore.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
|
|
We currently have significant issues with the amount of stack that
allocation in XFS uses, especially in the writeback path. We can
easily consume 4k of stack between mapping the page, manipulating
the bmap btree and allocating blocks from the free list. Not to
mention btree block readahead and other functionality that issues IO
in the allocation path.
As a result, we can no longer fit allocation in the writeback path
in the stack space provided on x86_64. To alleviate this problem,
introduce an allocation workqueue and move all allocations to a
seperate context. This can be easily added as an interposing layer
into xfs_alloc_vextent(), which takes a single argument structure
and does not return until the allocation is complete or has failed.
To do this, add a work structure and a completion to the allocation
args structure. This allows xfs_alloc_vextent to queue the args onto
the workqueue and wait for it to be completed by the worker. This
can be done completely transparently to the caller.
The worker function needs to ensure that it sets and clears the
PF_TRANS flag appropriately as it is being run in an active
transaction context. Work can also be queued in a memory reclaim
context, so a rescuer is needed for the workqueue.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
Sparse identified some unsafe handling of open flags in the xfs open
by handle ioctl code. Update the code to use the correct access
macros to ensure that we handle the open flags correctly.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
The problem occurs on !CONFIG_VM86 kernels [1] when a kernel-mode task
returns from a system call with a pending signal.
A real-life scenario is a child of 'khelper' returning from a failed
kernel_execve() in ____call_usermodehelper() [ kernel/kmod.c ].
kernel_execve() fails due to a pending SIGKILL, which is the result of
"kill -9 -1" (at least, busybox's init does it upon reboot).
The loop is as follows:
* syscall_exit_work:
- work_pending: // start_of_the_loop
- work_notify_sig:
- do_notify_resume()
- do_signal()
- if (!user_mode(regs)) return;
- resume_userspace // TIF_SIGPENDING is still set
- work_pending // so we call work_pending => goto
// start_of_the_loop
More information can be found in another LKML thread:
http://www.serverphorums.com/read.php?12,457826
[1] the problem was also seen on MIPS.
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Link: http://lkml.kernel.org/r/1332448765.2299.68.camel@dimm
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
To fix the deadlock caused by repeatedly calling xfs_rtfree_extent
- removed xfs_ilock() and xfs_trans_ijoin() from xfs_rtfree_extent(),
instead added asserts that the inode is locked and has an inode_item
attached to it.
- in xfs_bunmapi() when dealing with an inode with the rt flag
call xfs_ilock() and xfs_trans_ijoin() so that the
reference count is bumped on the inode and attached it to the
transaction before calling into xfs_bmap_del_extent, similar to
what we do in xfs_bmap_rtalloc.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
git://people.freedesktop.org/~airlied/linux
Pull nouveau destaging + Kelper modesetting support from Dave Airlie:
"This pull request is unexpected and not something I had mentioned
previously.
So NVIDIA announced new Kepler GPUs this morning, and Ben has killed
himself getting modesetting support for them together to have on
launch day. Most of the code to support the new chips has already
gone in, however this pull contains a few more pieces along with the
final enables so the driver binds to the new Kepler cards. Its quite
amazing that nouveau can support a GPU on its launch day even if its
just unaccelerated modesetting, and I'd like to have support in the
next kernel.
In order to sweeten the deal, Ben has also requested nouveau destage
and become ABI stable, the only change is the version number bump
which he prepared userspace for quite a long time ago. The driver
hasn't broken ABI since that one big break that caused a lot of fuss.
It's also quite a small set of code, and not likely to break anything."
* 'drm-nouveau-destage' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/dp: support version 4.0 of DP table
drm/nve0/disp: nvidia randomly decided to move the dithering method
drm/nve0: initial modesetting support for kepler chipsets
drm/nouveau: add bios connector type for dms59
drm/nouveau: move out of staging drivers
drm/nouveau: bump version to 1.0.0
drm/nvd0/disp: ignore clock set if no pclk
drm/nouveau: oops, increase channel dispc_vma to 4
drm/nouveau: inform userspace of new kernel subchannel requirements
drm/nouveau: remove m2mf creation on userspace channels
drm/nvc0-/disp: reimplement flip completion method as fifo method
drm/nouveau: move fence sequence check to start of loop
drm/nouveau: remove subchannel names from places where it doesn't matter
drm/nouveau/ttm: always do buffer moves on kernel channel
|
