| Age | Commit message (Collapse) | Author |
|---|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The GSWIP switch is a platform device, so the initial set of constraints
that I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the GSWIP switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The gswip driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Nobody in this driver calls mdiobus_unregister(), which is necessary if
mdiobus_register() completes successfully. So if the devres callbacks
that free the mdiobus get invoked (this is the case when unbinding the
driver), mdiobus_free() will BUG if the mdiobus is still registered,
which it is.
My speculation is that this is due to the fact that prior to commit
ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
from June 2020, _devm_mdiobus_free() used to call mdiobus_unregister().
But at the time that the mt7530 support was introduced in May 2021, the
API was already changed. It's therefore likely that the blamed patch was
developed on an older tree, and incorrectly adapted to net-next. This
makes the Fixes: tag correct.
Fix the problem by using the devres variant of mdiobus_register.
Fixes: ba751e28d442 ("net: dsa: mt7530: add interrupt support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Seville VSC9959 switch is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the seville switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The seville driver has a code structure that could accommodate both the
mdiobus_unregister and mdiobus_free calls, but it has an external
dependency upon mscc_miim_setup() from mdio-mscc-miim.c, which calls
devm_mdiobus_alloc_size() on its behalf. So rather than restructuring
that, and exporting yet one more symbol mscc_miim_teardown(), let's work
with devres and replace of_mdiobus_register with the devres variant.
When we use all-devres, we can ensure that devres doesn't free a
still-registered bus (it either runs both callbacks, or none).
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Felix VSC9959 switch is a PCI device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the felix switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The felix driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc_size() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Starfighter 2 is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the bcm_sf2 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The bcm_sf2 driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The ar9331 is an MDIO device, so the initial set of constraints that I
thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the ar9331 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The ar9331 driver doesn't have a complex code structure for mdiobus
removal, so just replace of_mdiobus_register with the devres variant in
order to be all-devres and ensure that we don't free a still-registered
bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The mv88e6xxx is an MDIO device, so the initial set of constraints that
I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the Marvell switch driver on shutdown.
systemd-shutdown[1]: Powering off.
mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down
fsl-mc dpbp.9: Removing from iommu group 7
fsl-mc dpbp.8: Removing from iommu group 7
------------[ cut here ]------------
kernel BUG at drivers/net/phy/mdio_bus.c:677!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15
pc : mdiobus_free+0x44/0x50
lr : devm_mdiobus_free+0x10/0x20
Call trace:
mdiobus_free+0x44/0x50
devm_mdiobus_free+0x10/0x20
devres_release_all+0xa0/0x100
__device_release_driver+0x190/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x4c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
kernel_power_off+0x34/0x6c
__do_sys_reboot+0x15c/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The Marvell driver already has a good structure for mdiobus removal, so
just plug in mdiobus_free and get rid of devres.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Rafael Richter <Rafael.Richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Today we have the code to mark connections and sessions
(and tcons) for reconnect clubbed with the code to close
the socket and abort all mids in the same function.
Sometimes, we need to mark connections and sessions
outside cifsd thread. So as a part of this change, I'm
splitting this function into two different functions and
calling them one after the other in cifs_reconnect.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
cifs_mark_tcp_ses_conns_for_reconnect helper function is now
meant to be used by any of the threads to mark a channel
(or all the channels) for reconnect.
Replace all such manual changes to tcpStatus to use this
helper function, which takes care that the right channels,
smb sessions and tcons are marked for reconnect.
Also includes one line minor change
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
When 803.2ad mode enables a participating port, it should update
the slave-array. I have observed that the member links are participating
and are part of the active aggregator while the traffic is egressing via
only one member link (in a case where two links are participating). Via
kprobes I discovered that slave-arr has only one link added while
the other participating link wasn't part of the slave-arr.
I couldn't see what caused that situation but the simple code-walk
through provided me hints that the enable_port wasn't always associated
with the slave-array update.
Fixes: ee6377147409 ("bonding: Simplify the xmit function for modes that use xmit_hash")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220207222901.1795287-1-maheshb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Mayuresh reported commit 20802d8d477d ("riscv: extable: add a dedicated
uaccess handler") breaks the writev02 test case in LTP. This is due to
the err reg isn't correctly set with the errno(-EFAULT in writev02
case). First of all, the err and zero regs are reg numbers rather than
reg offsets in struct pt_regs; Secondly, regs_set_gpr() should write
the regs when offset isn't zero(zero means epc)
Fix it by correcting regs_set_gpr() logic and passing the correct reg
offset to it.
Reported-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Fixes: 20802d8d477d ("riscv: extable: add a dedicated uaccess handler")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
This caused a significant performance degredation when using generic XDP
with multiple queues.
Fixes: f5cedc84a30d2 ("gve: Add transmit and receive support")
Signed-off-by: Tao Liu <xliutaox@google.com>
Link: https://lore.kernel.org/r/20220207175901.2486596-1-jeroendb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The kernel parameter "tp_printk_stop_on_boot" starts with "tp_printk" which is
the same as another kernel parameter "tp_printk". If "tp_printk" setup is
called before the "tp_printk_stop_on_boot", it will override the latter
and keep it from being set.
This is similar to other kernel parameter issues, such as:
Commit 745a600cf1a6 ("um: console: Ignore console= option")
or init/do_mounts.c:45 (setup function of "ro" kernel param)
Fix it by checking for a "_" right after the "tp_printk" and if that
exists do not process the parameter.
Link: https://lkml.kernel.org/r/20220208195421.969326-1-jsyoo5b@gmail.com
Signed-off-by: JaeSang Yoo <jsyoo5b@gmail.com>
[ Fixed up change log and added space after if condition ]
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Add an RTLA entry in the MAINTAINERS file with Steven Rostedt and
myself as maintainers.
Link: https://lkml.kernel.org/r/50d8870522580905a1c7f3e6fb611a700f632af1.1643994005.git.bristot@kernel.org
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Fix a bug of kunit documentation.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205773
: Quoting Steve Pfetsch:
:
: kunit documentation is incorrect:
: https://kunit.dev/third_party/stable_kernel/docs/usage.html
: struct rectangle *self = container_of(this, struct shape, parent);
:
:
: Shouldn't it be:
: struct rectangle *self = container_of(this, struct rectangle, parent);
: ?
Signed-off-by: Akira Kawata <akirakawata1@gmail.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Pull NFS client fixes from Anna Schumaker:
"Stable Fixes:
- Fix initialization of nfs_client cl_flags
Other Fixes:
- Fix performance issues with uncached readdir calls
- Fix potential pointer dereferences in rpcrdma_ep_create
- Fix nfs4_proc_get_locations() kernel-doc comment
- Fix locking during sunrpc sysfs reads
- Update my email address in the MAINTAINERS file to my new
kernel.org email"
* tag 'nfs-for-5.17-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
SUNRPC: lock against ->sock changing during sysfs read
MAINTAINERS: Update my email address
NFS: Fix nfs4_proc_get_locations() kernel-doc comment
xprtrdma: fix pointer derefs in error cases of rpcrdma_ep_create
NFS: Fix initialisation of nfs_client cl_flags field
NFS: Avoid duplicate uncached readdir calls on eof
NFS: Don't skip directory entries when doing uncached readdir
NFS: Don't overfill uncached readdir pages
|
|
In cifsd thread, we should continue to call cifs_reconnect
whenever server->tcpStatus is marked as CifsNeedReconnect.
This was inexplicably removed by one of my recent commits.
Fixing that here.
Fixes: a05885ce13bd ("cifs: fix the connection state transitions with multichannel")
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
asm/svm.h is the correct place for all values that are defined in
the SVM spec, and that includes AVIC.
Also add some values from the spec that were not defined before
and will be soon useful.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220207155447.840194-10-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
inhibiting it
kvm_apic_update_apicv is called when AVIC is still active, thus IRR bits
can be set by the CPU after it is called, and don't cause the irr_pending
to be set to true.
Also logic in avic_kick_target_vcpu doesn't expect a race with this
function so to make it simple, just keep irr_pending set to true and
let the next interrupt injection to the guest clear it.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220207155447.840194-9-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
L2 control them
Fix a corner case in which the L1 hypervisor intercepts
interrupts (INTERCEPT_INTR) and either doesn't set
virtual interrupt masking (V_INTR_MASKING) or enters a
nested guest with EFLAGS.IF disabled prior to the entry.
In this case, despite the fact that L1 intercepts the interrupts,
KVM still needs to set up an interrupt window to wait before
injecting the INTR vmexit.
Currently the KVM instead enters an endless loop of 'req_immediate_exit'.
Exactly the same issue also happens for SMIs and NMI.
Fix this as well.
Note that on VMX, this case is impossible as there is only
'vmexit on external interrupts' execution control which either set,
in which case both host and guest's EFLAGS.IF
are ignored, or not set, in which case no VMexits are delivered.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220207155447.840194-8-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM already honours few clean bits thus it makes sense
to let the nested guest know about it.
Note that KVM also doesn't check if the hardware supports
clean bits, and therefore nested KVM was
already setting clean bits and L0 KVM
was already honouring them.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220207155447.840194-6-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
While RSM induced VM entries are not full VM entries,
they still need to be followed by actual VM entry to complete it,
unlike setting the nested state.
This patch fixes boot of hyperv and SMM enabled
windows VM running nested on KVM, which fail due
to this issue combined with lack of dirty bit setting.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Message-Id: <20220207155447.840194-5-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
While usually, restoring the smm state makes the KVM enter
the nested guest thus a different vmcb (vmcb02 vs vmcb01),
KVM should still mark it as dirty, since hardware
can in theory cache multiple vmcbs.
Failure to do so, combined with lack of setting the
nested_run_pending (which is fixed in the next patch),
might make KVM re-enter vmcb01, which was just exited from,
with completely different set of guest state registers
(SMM vs non SMM) and without proper dirty bits set,
which results in the CPU reusing stale IDTR pointer
which leads to a guest shutdown on any interrupt.
On the real hardware this usually doesn't happen,
but when running nested, L0's KVM does check and
honour few dirty bits, causing this issue to happen.
This patch fixes boot of hyperv and SMM enabled
windows VM running nested on KVM.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Message-Id: <20220207155447.840194-4-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Turns out that due to review feedback and/or rebases
I accidentally moved the call to nested_svm_load_cr3 to be too early,
before the NPT is enabled, which is very wrong to do.
KVM can't even access guest memory at that point as nested NPT
is needed for that, and of course it won't initialize the walk_mmu,
which is main issue the patch was addressing.
Fix this for real.
Fixes: 232f75d3b4b5 ("KVM: nSVM: call nested_svm_load_cr3 on nested state load")
Cc: stable@vger.kernel.org
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220207155447.840194-3-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When the guest doesn't enable paging, and NPT/EPT is disabled, we
use guest't paging CR3's as KVM's shadow paging pointer and
we are technically in direct mode as if we were to use NPT/EPT.
In direct mode we create SPTEs with user mode permissions
because usually in the direct mode the NPT/EPT doesn't
need to restrict access based on guest CPL
(there are MBE/GMET extenstions for that but KVM doesn't use them).
In this special "use guest paging as direct" mode however,
and if CR4.SMAP/CR4.SMEP are enabled, that will make the CPU
fault on each access and KVM will enter endless loop of page faults.
Since page protection doesn't have any meaning in !PG case,
just don't passthrough these bits.
The fix is the same as was done for VMX in commit:
commit 656ec4a4928a ("KVM: VMX: fix SMEP and SMAP without EPT")
This fixes the boot of windows 10 without NPT for good.
(Without this patch, BSP boots, but APs were stuck in endless
loop of page faults, causing the VM boot with 1 CPU)
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Message-Id: <20220207155447.840194-2-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Remove a WARN on an "AVIC IPI invalid target" exit, the WARN is trivial
to trigger from guest as it will fail on any destination APIC ID that
doesn't exist from the guest's perspective.
Don't bother recording anything in the kernel log, the common tracepoint
for kvm_avic_incomplete_ipi() is sufficient for debugging.
This reverts commit 37ef0c4414c9743ba7f1af4392f0a27a99649f2a.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220204214205.3306634-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Commit 7707f7227f09 ("drm/rockchip: Add support for afbc") switched up
the rk3399_vop_big[] register windows, but it did so incorrectly.
The biggest problem is in rk3288_win23_data[] vs.
rk3368_win23_data[] .format field:
RK3288's format: VOP_REG(RK3288_WIN2_CTRL0, 0x7, 1)
RK3368's format: VOP_REG(RK3368_WIN2_CTRL0, 0x3, 5)
Bits 5:6 (i.e., shift 5, mask 0x3) are correct for RK3399, according to
the TRM.
There are a few other small differences between the 3288 and 3368
definitions that were swapped in commit 7707f7227f09. I reviewed them to
the best of my ability according to the RK3399 TRM and fixed them up.
This fixes IOMMU issues (and display errors) when testing with BG24
color formats.
Fixes: 7707f7227f09 ("drm/rockchip: Add support for afbc")
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119161104.1.I1d01436bef35165a8cdfe9308789c0badb5ff46a@changeid
|
|
The driver returns an error when devm_phy_optional_get() fails leaving
the previously enabled clock turned on. Change order and enable the
clock only after the phy has been acquired.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220126145549.617165-3-s.hauer@pengutronix.de
|
|
rtla osnoise and timerlat are causing a segmentation fault when running
with the --trace option on a kernel that does not support multiple
instances. For example:
[root@f34 rtla]# rtla osnoise top -t
failed to enable the tracer osnoise
Could not enable osnoiser tracer for tracing
Failed to enable the trace instance
Segmentation fault (core dumped)
This error happens because the exit code of the tools is trying
to destroy the trace instance that failed to be created.
Make osnoise_destroy_tool() aware of possible NULL osnoise_tool *,
and do not attempt to destroy it. This also simplifies the exit code.
Link: https://lkml.kernel.org/r/5660a2b6bf66c2655842360f2d7f6b48db5dba23.1644327249.git.bristot@kernel.org
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Fixes: 1eceb2fc2ca5 ("rtla/osnoise: Add osnoise top mode")
Fixes: 829a6c0b5698 ("rtla/osnoise: Add the hist mode")
Fixes: a828cd18bc4a ("rtla: Add timerlat tool and timelart top mode")
Fixes: 1eeb6328e8b3 ("rtla/timerlat: Add timerlat hist mode")
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
On reads with MMC_READ_MULTIPLE_BLOCK that fail,
the recovery handler will use MMC_READ_SINGLE_BLOCK for
each of the blocks, up to MMC_READ_SINGLE_RETRIES times each.
The logic for this is fixed to never report unsuccessful reads
as success to the block layer.
On command error with retries remaining, blk_update_request was
called with whatever value error was set last to.
In case it was last set to BLK_STS_OK (default), the read will be
reported as success, even though there was no data read from the device.
This could happen on a CRC mismatch for the response,
a card rejecting the command (e.g. again due to a CRC mismatch).
In case it was last set to BLK_STS_IOERR, the error is reported correctly,
but no retries will be attempted.
Fixes: 81196976ed946c ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/bc706a6ab08c4fe2834ba0c05a804672@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Commit a314520d82317650 ("arm64: disable Broadcom Vulcan platform")
did not remove the ARCH_VULCAN configuration symbol, as there were still
references to this symbol.
As of commits 240d3d5b2a7a3263 ("gpio: xlp: update GPIO_XLP dependency") and
f85a543e5373eeba ("arm64: defconfig: drop ARCH_VULCAN"), the last users
of ARCH_VULCAN have been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/9e8fef2cf4f2d5648e87076bc96601cff945ce40.1641996361.git.geert+renesas@glider.be'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
->sock can be set to NULL asynchronously unless ->recv_mutex is held.
So it is important to hold that mutex. Otherwise a sysfs read can
trigger an oops.
Commit 17f09d3f619a ("SUNRPC: Check if the xprt is connected before
handling sysfs reads") appears to attempt to fix this problem, but it
only narrows the race window.
Fixes: 17f09d3f619a ("SUNRPC: Check if the xprt is connected before handling sysfs reads")
Fixes: a8482488a7d6 ("SUNRPC query transport's source port")
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
Add the description of @server and @fhandle, and remove the excess
@inode in nfs4_proc_get_locations() kernel-doc comment to remove
warnings found by running scripts/kernel-doc, which is caused by
using 'make W=1'.
fs/nfs/nfs4proc.c:8219: warning: Function parameter or member 'server'
not described in 'nfs4_proc_get_locations'
fs/nfs/nfs4proc.c:8219: warning: Function parameter or member 'fhandle'
not described in 'nfs4_proc_get_locations'
fs/nfs/nfs4proc.c:8219: warning: Excess function parameter 'inode'
description in 'nfs4_proc_get_locations'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
If there are failures then we must not leave the non-NULL pointers with
the error value, otherwise `rpcrdma_ep_destroy` gets confused and tries
free them, resulting in an Oops.
Signed-off-by: Dan Aloni <dan.aloni@vastdata.com>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
For some long forgotten reason, the nfs_client cl_flags field is
initialised in nfs_get_client() instead of being initialised at
allocation time. This quirk was harmless until we moved the call to
nfs_create_rpc_client().
Fixes: dd99e9f98fbf ("NFSv4: Initialise connection to the server in nfs4_alloc_client()")
Cc: stable@vger.kernel.org # 4.8.x
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
Ever since Tomi extracted the core code in 2014 it's been defacto me
maintaining this, with help from others from dri-devel and sometimes
Linus (but those are mostly merge conflicts):
$ git shortlog -ns drivers/video/fbdev/core/ | head -n5
35 Daniel Vetter
23 Linus Torvalds
10 Hans de Goede
9 Dave Airlie
6 Peter Rosin
I think ideally we'd also record that the various firmware fb drivers
(efifb, vesafb, ...) are also maintained in drm-misc because for the
past few years the patches have either been to fix handover issues
with drm drivers, or caused handover issues with drm drivers. So any
other tree just doesn't make sense. But also, there's plenty of
outdated MAINTAINER entries for these with people and git trees that
haven't been active in years, so maybe let's just leave them alone.
And furthermore distros are now adopting simpledrm as the firmware fb
driver, so hopefully the need to care about the fbdev firmware drivers
will go down going forward.
Note that drm-misc is group maintained, I expect that to continue like
we've done before, so no new expectations that patches all go through
my hands. That would be silly. This also means I'm happy to put any
other volunteer's name in the M: line, but otherwise git log says I'm
the one who's stuck with this.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>Cc: Dave Airlie <airlied@gmail.com>
Acked-by: Helge Deller <deller@gmx.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linux Fbdev development list <linux-fbdev@vger.kernel.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: DRI Development <dri-devel@lists.freedesktop.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: Claudio Suarez <cssk@net-c.es>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Sven Schnelle <svens@stackframe.org>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220131210552.482606-2-daniel.vetter@ffwll.ch
|
|
Fix this kernel test robot warning:
drivers/video/fbdev/core/fbcon.c: In function 'fbcon_init':
drivers/video/fbdev/core/fbcon.c:1028:6: warning: variable 'cap' set but not used [-Wunused-but-set-variable]
The cap variable is only used when CONFIG_FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION
is enabled. Drop the temporary variable and use info->flags instead.
Fixes: 87ab9f6b7417 ("Revert "fbcon: Disable accelerated scrolling")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/YgFB4xqI+As196FR@p100
|
|
The check done by regulator_late_cleanup() to detect whether a regulator
is on was inconsistent with the check done by _regulator_is_enabled().
While _regulator_is_enabled() takes the enable GPIO into account,
regulator_late_cleanup() was not doing that.
This resulted in a false positive, e.g. when a GPIO-controlled fixed
regulator was used, which was not enabled at boot time, e.g.
reg_disp_1v2: reg_disp_1v2 {
compatible = "regulator-fixed";
regulator-name = "display_1v2";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
gpio = <&tlmm 148 0>;
enable-active-high;
};
Such regulator doesn't have an is_enabled() operation. Nevertheless
it's state can be determined based on the enable GPIO. The check in
regulator_late_cleanup() wrongly assumed that the regulator is on and
tried to disable it.
Signed-off-by: Oliver Barta <oliver.barta@aptiv.com>
Link: https://lore.kernel.org/r/20220208084645.8686-1-oliver.barta@aptiv.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With CPU re-ordering on write instructions, there might
be a chance that the HWO is set before the TRB is updated
with the new mapped buffer address.
And in the case where core is processing a list of TRBs
it is possible that it fetched the TRBs when the HWO is set
but before the buffer address is updated.
Prevent this by adding a memory barrier before the HWO
is updated to ensure that the core always process the
updated TRBs.
Fixes: f6bafc6a1c9d ("usb: dwc3: convert TRBs into bitshifts")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/1644207958-18287-1-git-send-email-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
d97a9d7aea04 ("staging/speakup: Add inflection synth parameter")
introduced the inflection parameter, but happened to drop the pitch
parameter from the dectlk driver. This restores it.
Cc: stable@vger.kernel.org
Fixes: d97a9d7aea04 ("staging/speakup: Add inflection synth parameter")
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20220206015626.aesbhvvdkmqsrbaw@begin
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into arm/fixes
Amlogic fixes for v5.17-rc
- meson6/meson8/meson8b UART compatible fixup to notably fix earlycon
* tag 'amlogic-fixes-v5.17-rc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
ARM: dts: meson8b: Fix the UART device-tree schema validation
ARM: dts: meson8: Fix the UART device-tree schema validation
ARM: dts: meson: Fix the UART compatible strings
Link: https://lore.kernel.org/r/746a7f25-1c96-9d27-3a08-e86b2af608ef@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Setting the output of a GPIO to 1 using gpiod_set_value(), followed by
reading the same GPIO using gpiod_get_value(), will currently yield an
incorrect result.
This is because the SiFive GPIO device stores the output values in reg_set,
not reg_dat.
Supply the flag BGPIOF_READ_OUTPUT_REG_SET to bgpio_init() so that the
generic driver reads the correct register.
Fixes: 96868dce644d ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Bartosz: added the Fixes tag]
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Currently it's possible that character device interface may return
the error codes which are not supposed to be seen by user space.
In this case it's EPROBE_DEFER.
Wrap it to return -ENODEV instead as sysfs does.
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events")
Fixes: 3c0d9c635ae2 ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Reported-by: Suresh Balakrishnan <suresh.balakrishnan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
The sl28cpld is a management controller found on the Kontron SMARC-sAL28
board for now. Support for it was added by me quite a while ago, but I
didn't add a MAINTAINERS entry. Add it now.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220207184652.1218447-1-michael@walle.cc'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Mention the IRC channels used for discussions about ARM/ARM64
sub-architectures and Devicetree. This documents purely existing state.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220207175503.425200-2-krzysztof.kozlowski@canonical.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add already used Krzysztof Kozlowski's Git tree for Samsung
S3C/S5P/Exynos ARM sub-architecture and IRC channel (#linux-exynos at
Libera). This documents purely existing state.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220207175503.425200-1-krzysztof.kozlowski@canonical.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixes
SoCFPGA fix for v5.17, part 1
- Fix a build error for socfpga_defconfig
* tag 'socfpga_fix_for_v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: fix missing RESET_CONTROLLER
Link: https://lore.kernel.org/r/20220207101002.7566-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The signal routing on the Skomer board was incorrect making
it impossible to mount root from the SD card. Fix this up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Cc: Stefan Hansson <newbyte@disroot.org>
Link: https://lore.kernel.org/r/20220205235312.446730-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into arm/fixes
Device Tree fixes for TI K3 platform for v5.17 merge window
* Update J721S2 platform to switch serial aliases to ttyS2.
* tag 'ti-k3-dt-fixes-for-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
arm64: dts: ti: k3-j721s2-common-proc-board: Alias console uart to serial2
arm64: dts: ti: k3-j721s2: Move aliases to board dts
Link: https://lore.kernel.org/r/20220204130716.fjlm4vvcbtzcwlwx@chalice
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
