| Age | Commit message (Collapse) | Author |
|---|
|
The global timer IRQ (PPI[0], PPI 11 in device tree terms) is a
rising edge interrupt. The ARM Cortex-A5 MPCore TRM in Chapter
10.1.2. Interrupt types and sources says:
"Interrupt is rising-edge sensitive."
The bits seem to be read-only, hence this missconfiguration had
no negative effect. However, with commit 992345a58e0c
("irqchip/gic: WARN if setting the interrupt type for a PPI fails")
warnings such as this get printed:
GIC: PPI11 is secure or misconfigured
With this change the new configuration matches the default
configuration and no warning is printed anymore.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.10 cycle.
Fair number of outreachy related patches in here. Some of these may well
have already been picked up by Greg but git will sort that out for us.
Also some good staging cleanup work from other sources. Thanks Brian and Lars
in particular for this.
New device support
* ACCES 104-quad-8
- New driver for this 8 channel encoder input board. Lots of new ABI with
this one.
* AD7766
- New driver supporting AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1 and
AD7767-2 24 bit ADCs.
* dmard 10
- New driver for this 3 axis accelerometer.
* Honeywell ABP pressure sensors.
- New driver covering 56 parts in this series (too many to list here!)
* HTS221
- New driver to support this relative humidiy and temperature device.
* LMP91000
- New driver for this potentiostat (form of chemical sensor). Nice example
of use of the buffered consumer interfaces and the use of a consumer
provided trigger.
* MiraMEMS DA311
- New driver for this 3 axis accelerometer.
* MiraMEMS DA280
- New driver for this 3 axis accelerometer. Follow up caught up with
vendor prefixes for these.
Staging graduations
* isl29018 light sensor
- Fixes and cleanups listed below (thanks for your hard work on this Brian!)
* sca3000
- Fixes and cleanups listed below. This was one of the small set of drivers
that went into staging when IIO was first added. Turns out it had a few
bugs and needed to be brought into the modern era! Not clear if I am
the only person who actually has one of these still wired to a board.
New features (Core)
- Add an iio_trigger_validate_own_device helper which relies on the device
and trigger having the same parent. Convenient to have this for some
of the more complex trigger / device interactions. Was hand rolled in
a few drivers already so good to bring it into the core.
- Add an iio_read_channel_offset in kernel access helper (similar to
the existing one for scale).
- IIO_ATTR_{RO, WO, RW} and IIO_DEVICE_ATTR_{RO, WO, RW} macros. These
lead some rather contrived function naming, but there is no denying they
do reduced boilerplate. I'm going to resist their introduction in
drivers 'unless' they form part of a larger set of cleanups.
- Counter channel type and index type.
New features (Drivers)
* hdc100x
- Triggered buffer support.
* mcp4725
- Device tree bindings and support.
- Voltage reference selection.
* ti-adc0832
- Triggered buffer support.
* ti-adc161s626
- Add regulator support allowing _scale and _offset values to be established
and exported.
New features (Tools)
* iio_generic_buffer
- -A option to force enable all channels rather than faulting if some are
already enabled (like -a does). Followup patches tidied this support up.
Cleanups (Core)
- Use kmalloc_array in iio_scan_mask_set.
- Take event_attrs field of iio_info structure constant
- Staging todo list updates. Most of it was long done.
- MAINTAINERS had a wrong directory listing.
Cleanups (Drivers)
* Missing i2c trivial devices entries.
* ad5592r
- Fix an endian type related sparse warnings.
* ad7150
- Constify the event attribute_group structures.
* ad7152
- Add some blank lines to improve readability.
- Sampling frequency control via chan-info element rather than hand rolled
attributes.
- add a new lock to avoid use of mlock for non state change related locking.
* ad7280
- Constify atrribute_group structure (second patch covers the event ones)
* ad7606 (Lars is driving most of the cleanup on this with some additions from
Eva)
- Fix improper setting of oversampling pins. This has been broken a very
long time in this staging driver, so not going to push this back to stable.
- Implement oversampling configuration via the chan_info mask element.
- Remove an unused int_vref_mv field.
- Remove a reundant name field from ad7606_chip_info.
- Remove default device configuration from platform_data in favour of
whatever the power on defaults are.
- Remove out of band error reporting in the kernel log as not providing
much information.
- Fix oversampling ratio by having 1 be the value for no oversampling.
- Avoid allocating buffer for each data capture.
- Factor out common code between periodic and one-shot capture.
- Move set_drvdat into common code.
- Let the common probe function return int rather than jumping through
an ERR_PTR.
- Pass struct device * into common remove to simplify code.
- Always run trigger handler only once per event (no one can remember why
it was being possibly done twice).
- Move over to the GPIO descriptor API to shorten and clarify code.
- Move the buffer code into the main file as it's not optional and is
now rather short in this driver.
- Fix the naming of the supply regulator.
- Rework regulator handling to handle errors including deferred probing.
- Tidy up a ptr_err or 0 return.
* ad7746
- Sampling frequency control via info_mask element rather than hand rolled
* ad7758
- Sampling frequency control via info_mask element rather than hand rolled
attributes.
* ad7816
- Constify the event attribute_group structure.
* adt7316
- Constify the event attribute group structures.
* ak8974
- Cleanup some sparse warnings about endian types.
* ak8975
- Cleanup some sparse warnings about endian types.
* bmi160
- Spare endian warning cleanups.
* isl29018 (towards staging graduation)
- Remove unusedvariables and defines.
- Improve consistency of error handling.
- Signed / unsigned comparison fixes.
- Use the IIO_DEVICE_ATTR_{RO, RW} macros
- Fix a race in in_illuminance_scale_available_show.
- Cleanup exit points of _read_raw
- Sanity check if in suspended state during a write_raw call as was already
done for read_raw.
- Document device tree bidnings.
- Document infrared supression controls.
- Add some newlines to improve readability and drop one that shouldn't be
there.
- Fix a poorly named functions name.
- Fix multiline coment syntax.
- Tidy up a pair or return statements by unifying them.
- Rename description in Kconfig for consistency with similar drivers.
* lidar
- cleanup power management by dropping unnecessary call.
* ltr501
- Use the claim_direct_mode helpers. Fix a race condition along the way.
* max1027
- Fix a dubious x | !y sparse warning.
- Use the new iio_trigger_validate_own_device helper.
* max440000
- Clean up some sparse warnings about endian types.
* mcp4725
- Use the regulator framework to establish the reference voltage rather than
getting it from platform data.
- Tidy up a comment typo.
- Fix a wrong PTR_ERR query (wrong regulator).
* mma7660
- Take a mma7660_nscale static.
* mma8452
- Use the new iio_trigger_validate_own_device helper.
- Use claim_direct_mode helpers - fix a race condition along the way.
* mpl3115
- Use claim_direct_mode helpers - fix a race condition along the way.
* ms65611
- Tidy up regulator error handling and clean out a static warning in the mix.
* sca3000
- Avoid a potential unitialized variable if a hardware read returns a value
that isn't actually supported (mostly warning supression).
- Fix a use before setting of the indio_dev->buffer pointer. Broken for
a very long time so not going to rush this into stable.
- Merge buffer file with core file. We used to always split these.
Sometimes it's just not worth the hassle. In this case the device's main
feature is it's hardware fifos so unlikely anyone would want to run it
without.
- Drop the sca3000_register_ring_funcs function as it's a pointless wrapper
once we have only one file.
- Fix cleaning of flag + setting of size of scan. Without this you can't
start the buffer twice and expect sensible (or any) results. Again,
broken for a long time so not heading for stable.
- Drop the custom watershed setting ABI - for now we'll just support one
value.
- Move to a hybrid hard / soft buffer design (how we've been doing it
for similar devices for a while now!)
- Cleanup some unusued variables.
- Use a fake channel to support core handling of freefall event registration.
- Cleanup the register defines.
- Fix an off by one error in axis due to IIO_NO_MOD taking up the 0 value.
Been broken since first admission of IIO to the staging tree.
- Add readback of the 3db low pass filter frequency and later writing
allowing droppign of custom measurement mode attributes as they can
be represented by the filter choices that is their main characteristic.
- Drop non standard revision attr and replace with dev_info on probe.
- Avoid a race in probe.
- Various formatting fixes.
- Kernel-docify docs that were very nearly in the write format.
* tsl2583
- Constify attribute_group structure.
* zpa2326
- Drop a redundant DEBUG ifdef.
Cleanups (Tools)
* iio_generic_buffer
- Fix the ? arguement. Previously it sort of worked as you got the help
message as a result of it not recognising the arguement.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.9 cycle.
* atlas chemical
- Fix alignment of big endian values in a larger storage (by using the right
size storage)
* maxim thermocouple
- Fix alignment of big endian values in larger (by using the correct
sized storage).
* sca3000
- Handle unexpected mode values.
* ti-adc081
- Select IIO_TRIGGERED_BUFFER to avoid build errors
|
|
This fixes a race condition where one thread that is entering or
leaving a power-saving state can inadvertently ignore the lock bit
that was set by another thread, and potentially also clear it.
The core_idle_lock_held function is called when the lock bit is
seen to be set. It polls the lock bit until it is clear, then
does a lwarx to load the word containing the lock bit and thread
idle bits so it can be updated. However, it is possible that the
value loaded with the lwarx has the lock bit set, even though an
immediately preceding lwz loaded a value with the lock bit clear.
If this happens then we go ahead and update the word despite the
lock bit being set, and when called from pnv_enter_arch207_idle_mode,
we will subsequently clear the lock bit.
No identifiable misbehaviour has been attributed to this race.
This fixes it by checking the lock bit in the value loaded by the
lwarx. If it is set then we just go back and keep on polling.
Fixes: b32aadc1a8ed ("powerpc/powernv: Fix race in updating core_idle_state")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Commit 8117ac6a6c2f ("powerpc/powernv: Switch off MMU before entering
nap/sleep/rvwinkle mode", 2014-12-10) fixed a race condition where one
thread entering a KVM guest could switch the MMU context to the guest
while another thread was still in host kernel context with the MMU on.
That commit moved the point where a thread entering a power-saving
mode set its kvm_hstate.hwthread_state field in its PACA to
KVM_HWTHREAD_IN_IDLE from a point where the MMU was on to after the
MMU had been switched off. That commit also added a comment
explaining that we have to switch to real mode before setting
hwthread_state to avoid this race.
Nevertheless, commit 4eae2c9ae54a ("powerpc/powernv: Make
pnv_powersave_common more generic", 2016-07-08) subsequently moved
the setting of hwthread_state back to a point where the MMU is on,
thus reintroducing the race, despite the comment saying that this
should not be done being included in full in the context lines of
the patch that did it.
This fixes the race again and adds a bigger and shoutier comment
explaining the potential race condition.
Fixes: 4eae2c9ae54a ("powerpc/powernv: Make pnv_powersave_common more generic")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Shreyas B. Prabhu <shreyasbp@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Standby (hotplug) memory should be added to ZONE_MOVABLE on s390. After
commit 199071f1 "s390/mm: make arch_add_memory() NUMA aware",
arch_add_memory() used memblock_end_of_DRAM() to find out the end of
ZONE_NORMAL and the beginning of ZONE_MOVABLE. However, commit 7f36e3e5
"memory-hotplug: add hot-added memory ranges to memblock before allocate
node_data for a node." moved the call of memblock_add_node() before
the call of arch_add_memory() in add_memory_resource(), and thus changed
the return value of memblock_end_of_DRAM() when called in
arch_add_memory(). As a result, arch_add_memory() will think that all
memory blocks should be added to ZONE_NORMAL.
Fix this by changing the logic in arch_add_memory() so that it will
manually iterate over all zones of a given node to find out which zone
a memory block should be added to.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use pr_cont instead of printk calls also within show_stack and
die in order to avoid extra line breaks.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
If of_genpd_add_provider_onecell() fails the following kernel crash is
observed on a kernel built with multi_v7_defconfig:
[ 1.739301] [00000040] *pgd=00000000
[ 1.739310] Internal error: Oops: 5 [#1] SMP ARM
[ 1.739319] Modules linked in:
[ 1.739328] CPU: 1 PID: 95 Comm: kworker/1:4 Not tainted 4.8.0-11897-g6b5e09a #1
[ 1.739331] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 1.739352] Workqueue: pm genpd_power_off_work_fn
[ 1.739356] task: ee63d400 task.stack: ee70a000
[ 1.739365] PC is at mutex_lock+0xc/0x4c
[ 1.739374] LR is at regulator_disable+0x2c/0x60
[ 1.739379] pc : [<c0bc0da0>] lr : [<c06e4b10>] psr: 60000013
[ 1.739379] sp : ee70beb0 ip : 10624dd3 fp : ee6e6280
[ 1.739382] r10: eefb0900 r9 : 00000000 r8 : c1309918
[ 1.739385] r7 : 00000000 r6 : 00000040 r5 : 00000000 r4 : 00000040
[ 1.739390] r3 : 0000004c r2 : 7fffd540 r1 : 000001e4 r0 : 00000040
Instead of returning of_genpd_add_provider_onecell() directly,
we should check its return value and in the case of error we
should unwind the previously taken actions, which in these case are:
- Call imx6q_pm_pu_power_off()
- Set imx6q_pu_domain.reg back to NULL
Setting imx6q_pu_domain.reg to NULL in the error case is important
as it will prevent further operations in the pu_reg regulator.
This kernel crash is not observed with imx_v6_v7_defconfig because
it selects GPU and VPU drivers, which are consumers of the GPC block
and thus change the refcount of the pu_reg regulator.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit 0159ec670763dd ("PM / Domains: Verify the PM domain is present
when adding a provider") the following regression is observed on imx6:
imx-gpc: probe of 20dc000.gpc failed with error -22
The gpc probe fails because of_genpd_add_provider_onecell() now checks
if all the domains are initialized via pm_genpd_present() function
and it fails because not all the power domains are initialized.
In order to fix this error, initialize all the power domains from
imx_gpc_domains[], not only the imx6q_pu_domain.base one.
Reported-by: Olof's autobooter <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
If the deferred ops transaction roll fails, we need to abort the intent
items if we haven't already logged a done item for it, regardless of
whether or not the deferred ops has had a transaction committed. Dave
found this while running generic/388.
Move the tracepoint to make it easier to track object lifetimes.
Reported-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
The background cowblocks scan job takes care of scanning for inodes with
potentially lingering blocks in the cow fork and clearing them out. If
the background scanner reclaims the cow fork blocks, however, it doesn't
immediately clear the cowblocks tag from the inode. Instead, the inode
remains tagged until the background scanner comes around again,
discovers the inode cow fork has no blocks, clears the tag and fires the
trace_xfs_inode_free_cowblocks_invalid() tracepoint to indicate that the
inode may have been incorrectly tagged.
This is not a major functional problem as the tag is ultimately cleared.
Nonetheless, clear the tag when an inode cow fork is explicitly emptied
to avoid the extra round trip through the background scanner and
spurious "invalid" tracepoint.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
These calls are still using the eofblocks tracepoints. The cowblocks
equivalents are already defined, we just aren't actually calling them.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
iomap_page_mkwrite_actor() calls __block_write_begin_int() with position
masked as pos & ~PAGE_MASK which is equivalent to pos & (PAGE_SIZE-1).
Thus it masks off high bits of file position. However
__block_write_begin_int() expects full file position on input. This does
not cause any visible issues because all __block_write_begin_int()
really cares about are low file position bits but still it is a bug
waiting to happen.
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
In some error paths in functions cxl_start_context and
afu_ioctl_start_work pid references to the current & group-leader tasks
can leak after they are taken. This patch fixes these error paths to
release these pid references before exiting the error path.
Fixes: 7b8ad495d592 ("cxl: Fix DSI misses when the context owning task exits")
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
From the beginning of the gpio-mpc8xxx.c, the "handle_level_irq"
has being used to handle GPIO interrupts in the PowerPC/Layerscape
platforms. But actually, almost all PowerPC/Layerscape platforms
assert an interrupt request upon either a high-to-low change or
any change on the state of the signal.
So the "handle_level_irq" is not reasonable for PowerPC/Layerscape
GPIO interrupt, it should be "handle_edge_irq". Otherwise the system
may lost some interrupts from the PIN's state changes.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
Pull UBI[FS] fixes from Richard Weinberger:
"This contains fixes for issues in both UBI and UBIFS:
- Fallout from the merge window, refactoring UBI code introduced some
issues.
- Fixes for an UBIFS readdir bug which can cause getdents() to busy
loop for ever and a bug in the UBIFS xattr code"
* tag 'upstream-4.9-rc2' of git://git.infradead.org/linux-ubifs:
ubifs: Abort readdir upon error
UBI: Fix crash in try_recover_peb()
ubi: fix swapped arguments to call to ubi_alloc_aeb
ubifs: Fix xattr_names length in exit paths
ubifs: Rename ubifs_rename2
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A few bug fixes and add some missing KERN_CONT annotations"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: add missing KERN_CONT to a few more debugging uses
fscrypto: lock inode while setting encryption policy
ext4: correct endianness conversion in __xattr_check_inode()
fscrypto: make XTS tweak initialization endian-independent
ext4: do not advertise encryption support when disabled
jbd2: fix incorrect unlock on j_list_lock
ext4: super.c: Update logging style using KERN_CONT
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target-pending fixes for v4.9-rc2.
This includes:
- Fix v4.1.y+ reference leak regression with concurrent TMR
ABORT_TASK + session shutdown. (Vaibhav Tandon)
- Enable tcm_fc w/ SCF_USE_CPUID to avoid host exchange timeouts
(Hannes)
- target/user error sense handling fixes. (Andy + MNC + HCH)
- Fix iscsi-target NOP_OUT error path iscsi_cmd descriptor leak
(Varun)
- Two EXTENDED_COPY SCSI status fixes for ESX VAAI (Dinesh Israni +
Nixon Vincent)
- Revert a v4.8 residual overflow change, that breaks sg_inq with
small allocation lengths.
There are a number of folks stress testing the v4.1.y regression fix
in their environments, and more folks doing iser-target I/O stress
testing atop recent v4.x.y code.
There is also one v4.2.y+ RCU conversion regression related to
explicit NodeACL configfs changes, that is still being tracked down"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/tcm_fc: use CPU affinity for responses
target/tcm_fc: Update debugging statements to match libfc usage
target/tcm_fc: return detailed error in ft_sess_create()
target/tcm_fc: print command pointer in debug message
target: fix potential race window in target_sess_cmd_list_waiting()
Revert "target: Fix residual overflow handling in target_complete_cmd_with_length"
target: Don't override EXTENDED_COPY xcopy_pt_cmd SCSI status code
target: Make EXTENDED_COPY 0xe4 failure return COPY TARGET DEVICE NOT REACHABLE
target: Re-add missing SCF_ACK_KREF assignment in v4.1.y
iscsi-target: fix iscsi cmd leak
iscsi-target: fix spelling mistake "Unsolicitied" -> "Unsolicited"
target/user: Fix comments to not refer to data ring
target/user: Return an error if cmd data size is too large
target/user: Use sense_reason_t in tcmu_queue_cmd_ring
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Couple of hwmon fixes:
Fix a potential ERR_PTR dereference in max31790 driver, and handle
temperature readings below 0 in adm9240 driver"
* tag 'hwmon-for-linus-v4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (max31790) potential ERR_PTR dereference
hwmon: (adm9240) handle temperature readings below 0
|
|
Pull IPMI updates from Corey Minyard:
"A small bug fix and a new driver for acting as an IPMI device.
I was on vacation during the merge window (a long vacation) but this
is a bug fix that should go in and a new driver that shouldn't hurt
anything.
This has been in linux-next for a month or so"
* tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: fix crash on reading version from proc after unregisted bmc
ipmi/bt-bmc: remove redundant return value check of platform_get_resource()
ipmi/bt-bmc: add a dependency on ARCH_ASPEED
ipmi: Fix ioremap error handling in bt-bmc
ipmi: add an Aspeed BT IPMI BMC driver
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/gpio/gpio-ath79.ko | grep alias
$
After this patch:
$ modinfo drivers/gpio/gpio-ath79.ko | grep alias
alias: of:N*T*Cqca,ar9340-gpioC*
alias: of:N*T*Cqca,ar9340-gpio
alias: of:N*T*Cqca,ar7100-gpioC*
alias: of:N*T*Cqca,ar7100-gpio
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Aban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2016-10-21
Here are some more Bluetooth fixes for the 4.9 kernel:
- Fix to btwilink driver probe function return value
- Power management fix to hci_bcm
- Fix to encoding name in scan response data
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds NAND DT properties for NS2 SVK to configure the bus
width width and OOB sector size
Signed-off-by: Prafulla Kota <prafulla.kota@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Most of getsockopt handlers in net/sctp/socket.c check len against
sizeof some structure like:
if (len < sizeof(int))
return -EINVAL;
On the first look, the check seems to be correct. But since len is int
and sizeof returns size_t, int gets promoted to unsigned size_t too. So
the test returns false for negative lengths. Yes, (-1 < sizeof(long)) is
false.
Fix this in sctp by explicitly checking len < 0 before any getsockopt
handler is called.
Note that sctp_getsockopt_events already handled the negative case.
Since we added the < 0 check elsewhere, this one can be removed.
If not checked, this is the result:
UBSAN: Undefined behaviour in ../mm/page_alloc.c:2722:19
shift exponent 52 is too large for 32-bit type 'int'
CPU: 1 PID: 24535 Comm: syz-executor Not tainted 4.8.1-0-syzkaller #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.1-0-gb3ef39f-prebuilt.qemu-project.org 04/01/2014
0000000000000000 ffff88006d99f2a8 ffffffffb2f7bdea 0000000041b58ab3
ffffffffb4363c14 ffffffffb2f7bcde ffff88006d99f2d0 ffff88006d99f270
0000000000000000 0000000000000000 0000000000000034 ffffffffb5096422
Call Trace:
[<ffffffffb3051498>] ? __ubsan_handle_shift_out_of_bounds+0x29c/0x300
...
[<ffffffffb273f0e4>] ? kmalloc_order+0x24/0x90
[<ffffffffb27416a4>] ? kmalloc_order_trace+0x24/0x220
[<ffffffffb2819a30>] ? __kmalloc+0x330/0x540
[<ffffffffc18c25f4>] ? sctp_getsockopt_local_addrs+0x174/0xca0 [sctp]
[<ffffffffc18d2bcd>] ? sctp_getsockopt+0x10d/0x1b0 [sctp]
[<ffffffffb37c1219>] ? sock_common_getsockopt+0xb9/0x150
[<ffffffffb37be2f5>] ? SyS_getsockopt+0x1a5/0x270
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-sctp@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 3ac72b7b63d5 ("net: fec: align IP header in hardware") breaks
networking on mx28.
There is an erratum on mx28 (ENGR121613 - ENET big endian mode
not compatible with ARM little endian) that requires an additional
byte-swap operation to workaround this problem.
So call swap_buffer() prior to performing the IP header alignment
to restore network functionality on mx28.
Fixes: 3ac72b7b63d5 ("net: fec: align IP header in hardware")
Reported-and-tested-by: Henri Roosen <henri.roosen@ginzinger.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise we'll overflow the integer. This occurs when layer 3 tunneled
packets are handed off to the IPv6 layer.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Time Sync (PTP) implementation uses the divisor/shift value for converting
the clock ticks to nanoseconds. Driver currently defines shift value as 1,
this results in the nanoseconds value to be calculated as half the actual
value. Hence the user application fails to synchronize the device clock
value with the PTP master device clock. Need to use the 'shift' value of 0.
Signed-off-by: Sony.Chacko <Sony.Chacko@cavium.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The newly added __sca3000_get_base_freq function handles all valid
modes of the SCA3000_REG_ADDR_MODE register, but gcc notices
that any other value (i.e. 0x00) causes the base_freq variable to
not get initialized:
drivers/staging/iio/accel/sca3000_core.c: In function 'sca3000_write_raw':
drivers/staging/iio/accel/sca3000_core.c:527:23: error: 'base_freq' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This adds explicit error handling for unexpected register values,
to ensure this cannot happen.
Fixes: e0f3fc9b47e6 ("iio: accel: sca3000_core: implemented IIO_CHAN_INFO_SAMP_FREQ")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ico Doornekamp <ico@pruts.nl>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
endian value
This will result in a random value being reported on big endian architectures.
(thanks to Lars-Peter Clausen for pointing out the effects of this bug)
Only effects a value printed to the log, but as this reports the settings of
the probe in question it may be of direct interest to users.
Also, fixes the following sparse endianness warnings:
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
drivers/iio/chemical/atlas-ph-sensor.c:215:9: warning: cast to restricted __be16
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Fixes: e8dd92bfbff25 ("iio: chemical: atlas-ph-sensor: add EC feature")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
PTR_ERR should access the value just tested by IS_ERR
Generated by: scripts/coccinelle/tests/odd_ptr_err.cocci
CC: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
drivers/staging/iio/adc/ad7606.c:357:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
CC: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Remove pm_runtime_mark_last_busy() call that wasn't need in the probe
since the device should be put to sleep.
Clarification from Matt:
Basically it going to be suspended once pm_runtime_idle() is called,
and setting the last busy is useless and not needed.
Clearly this doesn't affect the device running but just makes the code
more consistent with other uses.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds triggered buffer support for the ti-adc0832 driver. Tested with
ADC0831 and ADC0832 by using SYSFS trigger.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Triggered buffer support uses the HDC100X's dual acquisition mode
to read both humidity and temperature in one shot.
This patch depends on
447136effbf4 ("iio: humidity: hdc100x: fix sensor data reads of
temp and humidity")
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
MCP47x6 chip supports selection of a voltage reference (VDD, VREF buffered
or unbuffered). MCP4725 doesn't have this feature thus the eventual setting
is ignored and user is warned.
The setting is stored only in the volatile memory of the chip. You need to
manually store it to the EEPROM of the chip via 'store_eeprom' sysfs entry.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Number 2 is referencing to the settings with the largest available
resistor.
No functional change.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Currently, this driver ignores all errors from regulator_get(). The way
it is now, it also breaks probe deferral (EPROBE_DEFER). The correct
behavior is to propagate the error to the upper layers so they can
handle it accordingly.
Rework the regulator handling so that it matches the standard behavior.
If the specific design uses a static always-on regulator and does not
explicitly specify it, regulator_get() will return the dummy regulator.
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The name passed to devm_regulator_get() should match the name of the
supply as specified in the device datasheet. The supply on this device
is called 'AVcc' while currently, the driver uses just 'vcc'.
Use 'avcc' to specify the supply voltage since it is custom to use the
lower-caps version of the datasheet name.
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Currently the ad7606 buffer handling code resides in its own source file.
But this file contains only 4 small functions of which half are just
wrappers around other functions. Buffer support is also always enabled for
this driver, so move them over to the main source file. This reduces the
amount of boilerplate code.
Also rename the main function from ad7606_core.c to ad7606.c since there is
only a single file now.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Convert the ad7606 driver away from the deprecated legacy GPIO API and use
the new GPIO descriptor API.
This also means that the platform data struct is now empty and can be
removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Currently the ad7606 driver installs the same function for the hard-irq and
threaded trigger handlers. This was introduced in commit 1caf7cb46135
("staging:iio:adc:ad7606 Convert to new channel registration method Update
Add missing call to iio_trigger_notify_done() Set pollfunc top and bottom
half handler"). Unfortunately the commit message does not mention why this
was done and Michael does not remember either.
Since the trigger handler function is idempotent (set a GPIO to 1) running
it twice does not do any harm, but is simply not necessary either. So set
the threaded trigger handler for the driver to NULL.
While we are at it also remove the function description comment that does
no say anything that can't be derived from the function name itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Currently the common remove function takes a struct iio_dev *. This
parameter is retrieved by the individual driver remove functions by calling
get_drvdata() on their device. To simplify the code let the common remove
function directly take a struct dev * and do the IIO device in retrieval
the common remove function.
This also aligns the interface with the common probe function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The common probe function for the ad7606 currently returns a struct iio_dev
pointer. The returned value is not used by the individual driver probe
functions other than for error checking.
Let the common probe function return a int instead to report the error
value directly (or 0 on success). This allows to simplify the code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Both the platform_device and SPI driver call set_drvdata() at the end of
their probe function. Move this into the common probe() function to reduce
duplicated code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Both the periodic buffer based and one-shot sysfs based capture methods
share a large portion of their code. Factor this out into a common helper
function.
Also provide a comment that better explains in more detail what is going on
in the capture function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Currently the ad7606 driver dynamically allocates and frees a transfer
buffer each time a sample capture is performed in buffered mode, which
introduces unnecessary overhead. The driver state struct already contains a
buffer that is used for transfers in one-shot mode. This buffer is large
enough to hold all samples, but not the timestamp that might be present in
buffered mode. Extend the buffer size to be able to contain the timestamp
and update the buffered capture function to use this buffer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Currently the ad7606 driver uses a value of 0 for the oversampling ratio to
express that no oversampling is done. Strictly speaking this means though
that no data capture is done at all. Instead change the driver to use a
value of 1, this is in accordance with what other drivers do and what the
IIO spec suggests.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
