| Age | Commit message (Collapse) | Author |
|---|
|
If mt76_wcid_alloc() fails, the "mt76.mutex" mutex needs to be released as
done in the other error handling paths of mt7915_add_interface().
Fixes: f3049b88b2b3 ("wifi: mt76: mt7915: allocate vif wcid in the same range as stations")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/b9d8fbfc19360bfe60b9cea1cb0f735ab3b4bc26.1727639596.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
To avoid incorrect cipher after disconnection, we should
do the key deletion process in this case.
Fixes: e6db67fa871d ("wifi: mt76: ignore key disable commands")
Signed-off-by: Michael Lo <michael.lo@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Tested-by: David Ruth <druth@chromium.org>
Reviewed-by: David Ruth <druth@chromium.org>
Link: https://patch.msgid.link/20240801024335.12981-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
When initializing the network card, unplugging the device will
trigger an -EPROTO error, resulting in a flood of error messages
being printed frantically.
The exception is printed as follows：
mt76x2u 2-2.4:1.0: vendor request req:47 off:9018 failed:-71
mt76x2u 2-2.4:1.0: vendor request req:47 off:9018 failed:-71
...
It will continue to print more than 2000 times for about 5 minutes,
causing the usb device to be unable to be disconnected. During this
period, the usb port cannot recognize the new device because the old
device has not disconnected.
There may be other operating methods that cause -EPROTO, but -EPROTO is
a low-level hardware error. It is unwise to repeat vendor requests
expecting to read correct data. It is a better choice to treat -EPROTO
and -ENODEV the same way.
Similar to commit 9b0f100c1970 ("mt76: usb: process URBs with status
EPROTO properly") do no schedule rx_worker for urb marked with status
set -EPROTO. I also reproduced this situation when plugging and
unplugging the device, and this patch is effective.
Just do not vendor request again for urb marked with status set -EPROTO.
Link: https://lore.kernel.org/all/531681bd-30f5-4a70-a156-bf8754b8e072@intel.com/
Link: https://lore.kernel.org/all/D4B9CC1FFC0CBAC3+20250105040607.154706-1-wangyuli@uniontech.com/
Fixes: b40b15e1521f ("mt76: add usb support to mt76 layer")
Co-developed-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://patch.msgid.link/9DD7DE7AAB497CB7+20250113070241.63590-1-wangyuli@uniontech.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v6.14 (take two)
- Add support for alpha-numerical port references on the RZ/V2H SoC,
- Add support for the RZ/G3E (R9A09G047) Soc.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Both i386 and x86_64 now copy the relocate_kernel() function into the control
page and execute it from there, using an open-coded function pointer.
Use a typedef for it instead.
[ bp: Put relocate_kernel_ptr ptr arithmetic on a single line. ]
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20250109140757.2841269-10-dwmw2@infradead.org
|
|
A few places in the kexec control code page make the assumption that the first
instruction of relocate_kernel is at the very start of the page.
To allow for Clang CFI information to be added to relocate_kernel(), as well
as the general principle of removing unwarranted assumptions, fix them to use
the external __relocate_kernel_start symbol that the linker adds. This means
using a separate addq and subq for calculating offsets, as the assembler can
no longer calculate the delta directly for itself and relocations aren't that
versatile. But those values can at least be used relative to a local label to
avoid absolute relocations.
Turn the jump from relocate_kernel() to identity_mapped() into a real indirect
'jmp *%rsi' too, while touching it. There was no real reason for it to be
a push+ret in the first place, and adding Clang CFI info will also give
objtool enough visibility to start complaining 'return with modified stack
frame' about it.
[ bp: Massage commit message. ]
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20250109140757.2841269-9-dwmw2@infradead.org
|
|
The KEXEC_JUMP flow is analogous to hibernation flows occurring before
and after creating an image and before and after jumping from the
restore kernel to the image one, which is why it uses the same device
callbacks as those hibernation flows.
Add comments explaining that to the code in question and update an
existing comment in it which appears a bit out of context.
No functional changes.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20250109140757.2841269-8-dwmw2@infradead.org
|
|
A recent commit caused the relocate_kernel() function to be invoked through
a function pointer, but it does not have CFI information. The resulting trap
occurs after the IDT and GDT have been invalidated, leading to a triple-fault
if CONFIG_CFI_CLANG is enabled.
Using SYM_TYPED_FUNC_START() to provide the CFI information looks like it will
require a prolonged battle with objtool. And is fairly pointless anyway, as
the actual signature comes from a __kcfi_typeid_… symbol emitted from the
C code based on the function prototype it thinks that relocate_kernel has,
rendering the check somewhat tautological.
The simple fix is just to mark machine_kexec() with __nocfi.
Fixes: eeebbde57113 ("x86/kexec: Invoke copy of relocate_kernel() instead of the original")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20250109140757.2841269-7-dwmw2@infradead.org
|
|
More and more I2C client drivers use debugfs entries and currently they
need to manage a subdir for their files on their own. This means
inconsistent naming for these subdirs and they are scattered all over
the debugfs-tree as well. Not to mention the duplicated code.
Let the I2C core provide and maintain a proper directory per client.
Note: It was considered to save the additional pointer in 'struct
i2c_client' and only provide a subdir when requested via a helper
function. When sketching this approach, more and more corner cases
appeared, though, so the current solution with its simple and unabiguous
code was chosen.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
|
|
When a 400KHz freq is used on this model of ELAN touchpad in Linux,
excessive smoothing (similar to when the touchpad's firmware detects
a noisy signal) is sometimes applied. As some devices' (e.g, Lenovo
V15 G4) ACPI tables specify a 400KHz frequency for this device and
some I2C busses (e.g, Designware I2C) default to a 400KHz freq,
force the speed to 100KHz as a workaround.
For future investigation: This problem may be related to the default
HCNT/LCNT values given by some busses' drivers, because they are not
specified in the aforementioned devices' ACPI tables, and because
the device works without issues on Windows at what is expected to be
a 400KHz frequency. The root cause of the issue is not known.
Signed-off-by: Randolph Ha <rha051117@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Introduce a new `riic_bus_barrier()` function to verify bus availability
before initiating an I2C transfer. This function enhances the bus
arbitration check by ensuring that the SDA and SCL lines are not held low,
in addition to checking the BBSY flag using `readb_poll_timeout()`.
Previously, only the BBSY flag was checked to determine bus availability.
However, it is possible for the SDA line to remain low even when BBSY = 0.
This new implementation performs an additional check on the SDA and SCL
lines to avoid potential bus contention issues.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Replace the hardcoded `1000000000` with the predefined `NSEC_PER_SEC`
macro for clarity. Simplify the code by introducing a `ns_per_tick`
variable to store `NSEC_PER_SEC / rate`, reducing redundancy and
improving readability.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
The riic_irqs array describes the supported IRQs by the RIIC driver and
does not change at runtime.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Simplify the `riic_i2c_probe()` function by using the
`devm_reset_control_get_optional_exclusive_deasserted()` API to request a
deasserted reset line. This eliminates the need to manually deassert the
reset control and the additional cleanup.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Replace raw bitmask values with the `GENMASK()` macro in the `i2c-riic`
driver to improve readability and maintain consistency.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Easier to read and ensures proper types.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Update the `riic_init_hw()` function to use the local `dev` pointer in
calls to `dev_err_probe()`. Previously, `riic_init_hw()` used
`riic->adapter.dev` in error reporting. Since this function is invoked
during the probe phase, the I2C adapter is not yet initialized, leading to
`(null) ...` being printed in error messages. This patch fixes the issue
by consistently using the local `dev` pointer, which points to
`riic->adapter.dev.parent`.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Refactor error handling in the riic_i2c_probe() and riic_init_hw()
functions by replacing multiple dev_err() calls with dev_err_probe().
Additionally, update the riic_init_hw() function to use a local `dev`
pointer instead of `riic->adapter.dev` for dev_err_probe(), as the I2C
adapter is not initialized at this stage. Drop the cast to (unsigned long)
in the riic_init_hw() function when printing the bus frequency, and update
the error message to display the frequency in Hz, improving clarity.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Refactor the IRQ handling in riic_i2c_probe by introducing a local variable
`irq` to store IRQ numbers instead of assigning them to `ret`. This change
improves code readability and clarity.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
After commit
cb33ff9e063c ("x86/kexec: Move relocate_kernel to kernel .data section"),
kernels configured with an option that uses -ffunction-sections, such as
CONFIG_LTO_CLANG, crash when kexecing because the value of relocate_kernel
does not match the value of __relocate_kernel_start so incorrect code gets
copied via machine_kexec_prepare().
$ llvm-nm good-vmlinux &| rg relocate_kernel
ffffffff83280d41 T __relocate_kernel_end
ffffffff83280b00 T __relocate_kernel_start
ffffffff83280b00 T relocate_kernel
$ llvm-nm bad-vmlinux &| rg relocate_kernel
ffffffff83266100 D __relocate_kernel_end
ffffffff83266100 D __relocate_kernel_start
ffffffff8120b0d8 T relocate_kernel
When -ffunction-sections is enabled, TEXT_MAIN matches on
'.text.[0-9a-zA-Z_]*' to coalesce the function specific functions back
into .text during link time after they have been optimized. Due to the
placement of TEXT_TEXT before KEXEC_RELOCATE_KERNEL in the x86 linker
script, the .text.relocate_kernel section ends up in .text instead of
.data.
Use a second dot in the relocate_kernel section name to avoid matching
on TEXT_MAIN, which matches a similar situation that happened in
commit
79cd2a11224e ("x86/retpoline,kprobes: Fix position of thunk sections with CONFIG_LTO_CLANG"),
which allows kexec to function properly.
While .data.relocate_kernel still ends up in the .data section via
DATA_MAIN -> DATA_DATA, ensure it is located with the
.text.relocate_kernel section as intended by performing the same
transformation.
Fixes: cb33ff9e063c ("x86/kexec: Move relocate_kernel to kernel .data section")
Fixes: 8dbec5c77bc3 ("x86/kexec: Add data section to relocate_kernel")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20250109140757.2841269-6-dwmw2@infradead.org
|
|
A ::preserve_context kimage can be invoked more than once, and the entry point
can be different every time. When the callee returns to the kernel, it leaves
the address of its entry point for next time on the stack.
That being the case, one might reasonably assume that the caller would
allocate space for it on the stack frame before actually performing the 'call'
into the callee.
Apparently not, though. Ever since the kjump code was first added in 2009, it
has set up a *new* stack at the top of the swap_page scratch page, then just
performed the 'call' without allocating any space for the re-entry address to
be returned. It then reads the re-entry point for next time from 0(%rsp) which
is actually the first qword of the page *after* the swap page, which might not
exist at all! And if the callee has written to that, then it will have
corrupted memory it doesn't own.
Correct this by pushing the entry point of the callee onto the stack before
calling it. The callee may then adjust it, or not, as it sees fit, and
subsequent invocations should work correctly either way.
Remove a stray push of zero to the *relocate_kernel* stack, which may have
been intended for this purpose, but which was actually just noise.
Also, loading the stack for the callee relied on the address of the swap page
being in %r10 without ever documenting that fact. Recent code changes made
that no longer true, so load it directly from the local kexec_pa_swap_page
variable instead.
Fixes: b3adabae8a96 ("x86/kexec: Drop page_list argument from relocate_kernel()")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20250109140757.2841269-5-dwmw2@infradead.org
|
|
The swap_pages function expects the swap page to be in %r10, but there
was no documentation to that effect. Once upon a time the setup code
used to load its value from a kernel virtual address and save it to an
address which is accessible in the identity-mapped page tables, and
*happened* to use %r10 to do so, with no comment that it was left there
on *purpose* instead of just being a scratch register. Once that was no
longer necessary, %r10 just holds whatever the kernel happened to leave
in it.
Now that the original value passed by the kernel is accessible via
%rip-relative addressing, load directly from there instead of using %r10
for it. But document the other parameters that the swap_pages function
*does* expect in registers.
Fixes: b3adabae8a96 ("x86/kexec: Drop page_list argument from relocate_kernel()")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20250109140757.2841269-4-dwmw2@infradead.org
|
|
The swap_pages() function will only actually *swap*, as its name implies, if
the preserve_context flag in the %r11 register is non-zero. On the way back
from a ::preserve_context kexec, ensure that the %r11 register is non-zero so
that the pages get swapped back.
Fixes: 9e5683e2d0b5 ("x86/kexec: Only swap pages for ::preserve_context mode")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20250109140757.2841269-3-dwmw2@infradead.org
|
|
The kernel switches to a new set of page tables during kexec. The global
mappings (_PAGE_GLOBAL==1) can remain in the TLB after this switch. This
is generally not a problem because the new page tables use a different
portion of the virtual address space than the normal kernel mappings.
The critical exception to that generalisation (and the only mapping
which isn't an identity mapping) is the kexec control page itself —
which was ROX in the original kernel mapping, but should be RWX in the
new page tables. If there is a global TLB entry for that in its prior
read-only state, it definitely needs to be flushed before attempting to
write through that virtual mapping.
It would be possible to just avoid writing to the virtual address of the
page and defer all writes until they can be done through the identity
mapping. But there's no good reason to keep the old TLB entries around,
as they can cause nothing but trouble.
Clear the PGE bit in %cr4 early, before storing data in the control page.
Fixes: 5a82223e0743 ("x86/kexec: Mark relocate_kernel page as ROX instead of RWX")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219592
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: "Ning, Hongyu" <hongyu.ning@linux.intel.com>
Co-developed-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: "Ning, Hongyu" <hongyu.ning@linux.intel.com>
Link: https://lore.kernel.org/r/20250109140757.2841269-2-dwmw2@infradead.org
|
|
The Call Trace is as below:
"
<TASK>
? show_regs.cold+0x1a/0x1f
? __rxe_cleanup+0x12c/0x170 [rdma_rxe]
? __warn+0x84/0xd0
? __rxe_cleanup+0x12c/0x170 [rdma_rxe]
? report_bug+0x105/0x180
? handle_bug+0x46/0x80
? exc_invalid_op+0x19/0x70
? asm_exc_invalid_op+0x1b/0x20
? __rxe_cleanup+0x12c/0x170 [rdma_rxe]
? __rxe_cleanup+0x124/0x170 [rdma_rxe]
rxe_destroy_qp.cold+0x24/0x29 [rdma_rxe]
ib_destroy_qp_user+0x118/0x190 [ib_core]
rdma_destroy_qp.cold+0x43/0x5e [rdma_cm]
rtrs_cq_qp_destroy.cold+0x1d/0x2b [rtrs_core]
rtrs_srv_close_work.cold+0x1b/0x31 [rtrs_server]
process_one_work+0x21d/0x3f0
worker_thread+0x4a/0x3c0
? process_one_work+0x3f0/0x3f0
kthread+0xf0/0x120
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
</TASK>
"
When too many rdma resources are allocated, rxe needs more time to
handle these rdma resources. Sometimes with the current timeout, rxe
can not release the rdma resources correctly.
Compared with other rdma drivers, a bigger timeout is used.
Fixes: 215d0a755e1b ("RDMA/rxe: Stop lookup of partially built objects")
Signed-off-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Link: https://patch.msgid.link/20250110160927.55014-1-yanjun.zhu@linux.dev
Tested-by: Joe Klein <joe.klein812@gmail.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
This patch sends IB_EVENT_QP_LAST_WQE_REACHED event on a QP that is in
error state and associated with an SRQ. This behaviour is incorporated
in flush_qp() which is called when QP transitions to error state.
Supports SRQ drain functionality added by commit 844bc12e6da3 ("IB/core:
add support for draining Shared receive queues")
Fixes: 844bc12e6da3 ("IB/core: add support for draining Shared receive queues")
Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Link: https://patch.msgid.link/20250107095053.81007-1-anumula@chelsio.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Stefano Garzarella says:
====================
vsock: some fixes due to transport de-assignment
v1: https://lore.kernel.org/netdev/20250108180617.154053-1-sgarzare@redhat.com/
v2:
- Added patch 3 to cancel the virtio close delayed work when de-assigning
the transport
- Added patch 4 to clean the socket state after de-assigning the transport
- Added patch 5 as suggested by Michael and Hyunwoo Kim. It's based on
Hyunwoo Kim and Wongi Lee patch [1] but using WARN_ON and covering more
functions
- Added R-b/T-b tags
This series includes two patches discussed in the thread started by
Hyunwoo Kim a few weeks ago [1], plus 3 more patches added after some
discussions on v1 (see changelog). All related to the case where a vsock
socket is de-assigned from a transport (e.g., because the connect fails
or is interrupted by a signal) and then assigned to another transport
or to no-one (NULL).
I tested with usual vsock test suite, plus Michal repro [2]. (Note: the repo
works only if a G2H transport is not loaded, e.g. virtio-vsock driver).
The first patch is a fix more appropriate to the problem reported in
that thread, the second patch on the other hand is a related fix but
of a different problem highlighted by Michal Luczaj. It's present only
in vsock_bpf and already handled in af_vsock.c
The third patch is to cancel the virtio close delayed work when de-assigning
the transport, the fourth patch is to clean the socket state after de-assigning
the transport, the last patch adds warnings and prevents null-ptr-deref in
vsock_*[has_data|has_space].
Hyunwoo Kim, Michal, if you can test and report your Tested-by that
would be great!
[1] https://lore.kernel.org/netdev/Z2K%2FI4nlHdfMRTZC@v4bel-B760M-AORUS-ELITE-AX/
[2] https://lore.kernel.org/netdev/2b3062e3-bdaa-4c94-a3c0-2930595b9670@rbox.co/
====================
Link: https://patch.msgid.link/20250110083511.30419-1-sgarzare@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Recent reports have shown how we sometimes call vsock_*_has_data()
when a vsock socket has been de-assigned from a transport (see attached
links), but we shouldn't.
Previous commits should have solved the real problems, but we may have
more in the future, so to avoid null-ptr-deref, we can return 0
(no space, no data available) but with a warning.
This way the code should continue to run in a nearly consistent state
and have a warning that allows us to debug future problems.
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/netdev/Z2K%2FI4nlHdfMRTZC@v4bel-B760M-AORUS-ELITE-AX/
Link: https://lore.kernel.org/netdev/5ca20d4c-1017-49c2-9516-f6f75fd331e9@rbox.co/
Link: https://lore.kernel.org/netdev/677f84a8.050a0220.25a300.01b3.GAE@google.com/
Co-developed-by: Hyunwoo Kim <v4bel@theori.io>
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Co-developed-by: Wongi Lee <qwerty@theori.io>
Signed-off-by: Wongi Lee <qwerty@theori.io>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Reviewed-by: Hyunwoo Kim <v4bel@theori.io>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Transport's release() and destruct() are called when de-assigning the
vsock transport. These callbacks can touch some socket state like
sock flags, sk_state, and peer_shutdown.
Since we are reassigning the socket to a new transport during
vsock_connect(), let's reset these fields to have a clean state with
the new transport.
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Cc: stable@vger.kernel.org
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
During virtio_transport_release() we can schedule a delayed work to
perform the closing of the socket before destruction.
The destructor is called either when the socket is really destroyed
(reference counter to zero), or it can also be called when we are
de-assigning the transport.
In the former case, we are sure the delayed work has completed, because
it holds a reference until it completes, so the destructor will
definitely be called after the delayed work is finished.
But in the latter case, the destructor is called by AF_VSOCK core, just
after the release(), so there may still be delayed work scheduled.
Refactor the code, moving the code to delete the close work already in
the do_close() to a new function. Invoke it during destruction to make
sure we don't leave any pending work.
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Cc: stable@vger.kernel.org
Reported-by: Hyunwoo Kim <v4bel@theori.io>
Closes: https://lore.kernel.org/netdev/Z37Sh+utS+iV3+eb@v4bel-B760M-AORUS-ELITE-AX/
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Tested-by: Hyunwoo Kim <v4bel@theori.io>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Some of the core functions can only be called if the transport
has been assigned.
As Michal reported, a socket might have the transport at NULL,
for example after a failed connect(), causing the following trace:
BUG: kernel NULL pointer dereference, address: 00000000000000a0
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 12faf8067 P4D 12faf8067 PUD 113670067 PMD 0
Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 15 UID: 0 PID: 1198 Comm: a.out Not tainted 6.13.0-rc2+
RIP: 0010:vsock_connectible_has_data+0x1f/0x40
Call Trace:
vsock_bpf_recvmsg+0xca/0x5e0
sock_recvmsg+0xb9/0xc0
__sys_recvfrom+0xb3/0x130
__x64_sys_recvfrom+0x20/0x30
do_syscall_64+0x93/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
So we need to check the `vsk->transport` in vsock_bpf_recvmsg(),
especially for connected sockets (stream/seqpacket) as we already
do in __vsock_connectible_recvmsg().
Fixes: 634f1a7110b4 ("vsock: support sockmap")
Cc: stable@vger.kernel.org
Reported-by: Michal Luczaj <mhal@rbox.co>
Closes: https://lore.kernel.org/netdev/5ca20d4c-1017-49c2-9516-f6f75fd331e9@rbox.co/
Tested-by: Michal Luczaj <mhal@rbox.co>
Reported-by: syzbot+3affdbfc986ecd9200fd@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/677f84a8.050a0220.25a300.01b3.GAE@google.com/
Tested-by: syzbot+3affdbfc986ecd9200fd@syzkaller.appspotmail.com
Reviewed-by: Hyunwoo Kim <v4bel@theori.io>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If the socket has been de-assigned or assigned to another transport,
we must discard any packets received because they are not expected
and would cause issues when we access vsk->transport.
A possible scenario is described by Hyunwoo Kim in the attached link,
where after a first connect() interrupted by a signal, and a second
connect() failed, we can find `vsk->transport` at NULL, leading to a
NULL pointer dereference.
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Cc: stable@vger.kernel.org
Reported-by: Hyunwoo Kim <v4bel@theori.io>
Reported-by: Wongi Lee <qwerty@theori.io>
Closes: https://lore.kernel.org/netdev/Z2LvdTTQR7dBmPb5@v4bel-B760M-AORUS-ELITE-AX/
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Hyunwoo Kim <v4bel@theori.io>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In order to optimize the size of driver private structure,
the memory for dev_attr is allocated dynamically during the
chip context initialization. In order to make certain runtime
decisions, store dev_attr in the qplib_res structure.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1736446693-6692-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
ulp_irq_stop() can be invoked from a context where FW is healthy or
when FW is in a reset state. In the latter case, ULP must stop all
interactions with HW/FW and also with application and stack. Added a
new parameter to the ulp_irq_stop() function to achieve that.
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1736446693-6692-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
MD Danish Anwar says:
====================
Add Multicast Filtering support for VLAN interface
This series adds Multicast filtering support for VLAN interfaces in dual
EMAC and HSR offload mode for ICSSG driver.
Patch 1/4 - Adds support for VLAN in dual EMAC mode
Patch 2/4 - Adds MC filtering support for VLAN in dual EMAC mode
Patch 3/4 - Create and export hsr_get_port_ndev() in hsr_device.c
Patch 4/4 - Adds MC filtering support for VLAN in HSR mode
[1] https://lore.kernel.org/all/20241216100044.577489-2-danishanwar@ti.com/
[2] https://lore.kernel.org/all/202412210336.BmgcX3Td-lkp@intel.com/#t
[3] https://lore.kernel.org/all/31bb8a3e-5a1c-4c94-8c33-c0dfd6d643fb@kernel.org/
v1 https://lore.kernel.org/all/20241216100044.577489-1-danishanwar@ti.com/
v2 https://lore.kernel.org/all/20241223092557.2077526-1-danishanwar@ti.com/
v3 https://lore.kernel.org/all/20250103092033.1533374-1-danishanwar@ti.com/
====================
Link: https://patch.msgid.link/20250110082852.3899027-1-danishanwar@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add multicast filtering support for VLAN interfaces in HSR offload mode
for ICSSG driver.
The driver calls vlan_for_each() API on the hsr device's ndev to get the
list of available vlans for the hsr device. The driver then sync mc addr of
vlan interface with a locally mainatined list emac->vlan_mcast_list[vid]
using __hw_addr_sync_multiple() API.
The driver then calls the sync / unsync callbacks.
In the sync / unsync call back, driver checks if the vdev's real dev is
hsr device or not. If the real dev is hsr device, driver gets the per
port device using hsr_get_port_ndev() and then driver passes appropriate
vid to FDB helper functions.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Create an API to get the net_device to the slave port of HSR device. The
API will take hsr net_device and enum hsr_port_type for which we want the
net_device as arguments.
This API can be used by client drivers who support HSR and want to get
the net_devcie of slave ports from the hsr device. Export this API for
the same.
This API needs the enum hsr_port_type to be accessible by the drivers using
hsr. Move the enum hsr_port_type from net/hsr/hsr_main.h to
include/linux/if_hsr.h for the same.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add multicast filtering support for VLAN interfaces in dual EMAC mode
for ICSSG driver.
The driver uses vlan_for_each() API to get the list of available
vlans. The driver then sync mc addr of vlan interface with a locally
mainatined list emac->vlan_mcast_list[vid] using __hw_addr_sync_multiple()
API.
__hw_addr_sync_multiple() is used instead of __hw_addr_sync() to sync
vdev->mc with local list because the sync_cnt for addresses in vdev->mc
will already be set by the vlan_dev_set_rx_mode() [net/8021q/vlan_dev.c]
and __hw_addr_sync() only syncs when the sync_cnt == 0. Whereas
__hw_addr_sync_multiple() can sync addresses even if sync_cnt is not 0.
Export __hw_addr_sync_multiple() so that driver can use it.
Once the local list is synced, driver calls __hw_addr_sync_dev() with
the local list, vdev, sync and unsync callbacks.
__hw_addr_sync_dev() is used with the local maintained list as the list
to synchronize instead of using __dev_mc_sync() on vdev because
__dev_mc_sync() on vdev will call __hw_addr_sync_dev() on vdev->mc and
sync_cnt for addresses in vdev->mc will already be set by the
vlan_dev_set_rx_mode() [net/8021q/vlan_dev.c] and __hw_addr_sync_dev()
only syncs if the sync_cnt of addresses in the list (vdev->mc in this case)
is 0. Whereas __hw_addr_sync_dev() on local list will work fine as the
sync_cnt for addresses in the local list will still be 0.
Based on change in addresses in the local list, sync / unsync callbacks
are invoked. In the sync / unsync API in driver, based on whether the ndev
is vlan or not, driver passes appropriate vid to FDB helper functions.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for VLAN filtering in dual EMAC mode.
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains a small batch of Netfilter/IPVS updates
for net-next:
1) Remove unused genmask parameter in nf_tables_addchain()
2) Speed up reads from /proc/net/ip_vs_conn, from Florian Westphal.
3) Skip empty buckets in hashlimit to avoid atomic operations that results
in false positive reports by syzbot with lockdep enabled, patch from
Eric Dumazet.
4) Add conntrack event timestamps available via ctnetlink,
from Florian Westphal.
netfilter pull request 25-01-11
* tag 'nf-next-25-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: conntrack: add conntrack event timestamp
netfilter: xt_hashlimit: htable_selective_cleanup() optimization
ipvs: speed up reads from ip_vs_conn proc file
netfilter: nf_tables: remove the genmask parameter
====================
Link: https://patch.msgid.link/20250111230800.67349-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Simplify error handling by replacing goto statements with automatic
calls to landlock_put_ruleset() when going out of scope.
This change depends on the TCP support.
Cc: Konstantin Meskhidze <konstantin.meskhidze@huawei.com>
Cc: Mikhail Ivanov <ivanov.mikhail1@huawei-partners.com>
Reviewed-by: Günther Noack <gnoack@google.com>
Link: https://lore.kernel.org/r/20250113161112.452505-3-mic@digikod.net
Signed-off-by: Mickaël Salaün <mic@digikod.net>
|
|
Simplify error handling by replacing goto statements with automatic
calls to landlock_put_ruleset() when going out of scope.
This change will be easy to backport to v6.6 if needed, only the
kernel.h include line conflicts. As for any other similar changes, we
should be careful when backporting without goto statements.
Add missing include file.
Reviewed-by: Günther Noack <gnoack@google.com>
Link: https://lore.kernel.org/r/20250113161112.452505-2-mic@digikod.net
Signed-off-by: Mickaël Salaün <mic@digikod.net>
|
|
Use __attribute_const__ for get_mode_access().
Reviewed-by: Günther Noack <gnoack3000@gmail.com>
Link: https://lore.kernel.org/r/20250110153918.241810-2-mic@digikod.net
Signed-off-by: Mickaël Salaün <mic@digikod.net>
|
|
A corrupted filesystem (e.g. bcachefs) might return weird files.
Instead of throwing a warning and allowing access to such file, treat
them as regular files.
Cc: Dave Chinner <david@fromorbit.com>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Paul Moore <paul@paul-moore.com>
Reported-by: syzbot+34b68f850391452207df@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/r/000000000000a65b35061cffca61@google.com
Reported-by: syzbot+360866a59e3c80510a62@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/r/67379b3f.050a0220.85a0.0001.GAE@google.com
Reported-by: Ubisectech Sirius <bugreport@ubisectech.com>
Closes: https://lore.kernel.org/r/c426821d-8380-46c4-a494-7008bbd7dd13.bugreport@ubisectech.com
Fixes: cb2c7d1a1776 ("landlock: Support filesystem access-control")
Reviewed-by: Günther Noack <gnoack3000@gmail.com>
Link: https://lore.kernel.org/r/20250110153918.241810-1-mic@digikod.net
Signed-off-by: Mickaël Salaün <mic@digikod.net>
|
|
Oleksij Rempel says:
====================
Introduce unified and structured PHY
This patch set introduces a unified and well-structured interface for
reporting PHY statistics. Instead of relying on arbitrary strings in PHY
drivers, this interface provides a consistent and structured way to
expose PHY statistics to userspace via ethtool.
The initial groundwork for this effort was laid by Jakub Kicinski, who
contributed patches to plumb PHY statistics to drivers and added support
for structured statistics in ethtool. Building on Jakub's work, I tested
the implementation with several PHYs, addressed a few issues, and added
support for statistics in two specific PHY drivers.
Most of changes are tracked in separate patches.
changes v6:
- drop ethtool_stat_add patch
changes v5:
- rebase against latest net-next
====================
Link: https://patch.msgid.link/20250110060517.711683-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for reporting PHY statistics in the DP83TG720 driver. This
includes cumulative tracking of link loss events, transmit/receive
packet counts, and error counts. Implemented functions to update and
provide statistics via ethtool, with optional polling support enabled
through `PHY_POLL_STATS`.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for reporting PHY statistics in the DP83TD510 driver. This
includes cumulative tracking of transmit/receive packet counts, and
error counts. Implemented functions to update and provide statistics via
ethtool, with optional polling support enabled through `PHY_POLL_STATS`.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add an optional polling interface for PHY statistics to simplify driver
implementation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
pair guide
Replace generic instructions for monitoring error counters with a
procedure using the unified PHY statistics interface (`--all-groups`).
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce a new way to report PHY statistics in a structured and
standardized format using the netlink API. This new method does not
replace the old driver-specific stats, which can still be accessed with
`ethtool -S <eth name>`. The structured stats are available with
`ethtool -S <eth name> --all-groups`.
This new method makes it easier to diagnose problems by organizing stats
in a consistent and documented way.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
