| Age | Commit message (Collapse) | Author |
|---|
|
Commit a5681e20b541 ("net/ibmnvic: Fix deadlock problem
in reset") made the change to hold the RTNL lock during
driver reset but still calls netdev_notify_peers, which
results in a deadlock. Instead, use call_netdevice_notifiers,
which is functionally the same except that it does not
take the RTNL lock again.
Fixes: a5681e20b541 ("net/ibmnvic: Fix deadlock problem in reset")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 78139c94dc8c ("net: vhost: lock the vqs one by one") moved the vq
lock to improve scalability, but introduced a possible deadlock in
vhost-iotlb. vhost_iotlb_notify_vq() now takes vq->mutex while holding
the device's IOTLB spinlock. And on the vhost_iotlb_miss() path, the
spinlock is taken while holding vq->mutex.
Since calling vhost_poll_queue() doesn't require any lock, avoid the
deadlock by not taking vq->mutex.
Fixes: 78139c94dc8c ("net: vhost: lock the vqs one by one")
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Yoshihiro Shimoda says:
====================
net: phy: micrel: add toggling phy reset
This patch set is for R-Car Gen3 Salvator-XS boards. If we do
the following method, the phy cannot link up correctly.
1) Kernel boots by using initramfs.
--> No open the nic, so phy_device_register() and phy_probe()
deasserts the reset.
2) Kernel enters the suspend.
--> So, keep the reset signal as deassert.
--> On R-Car Salvator-XS board, unfortunately, the board power is
turned off.
3) Kernel returns from suspend.
4) ifconfig eth0 up
--> Then, since edge signal of the reset doesn't happen,
it cannot link up.
5) ifconfig eth0 down
6) ifconfig eth0 up
--> In this case, it can link up.
When resolving this issue after I got feedback from Andrew and Heiner,
I found an issue that the phy_device.c didn't call phy_resume()
if the PHY was not attached. So, patch 1 fixes it and add toggling
the phy reset to the micrel phy driver.
Changes from v1 (as RFC):
- No remove the current code of phy_device.c to avoid any side effects.
- Fix the mdio_bus_phy_resume() in phy_device.c.
- Add toggling the phy reset in micrel.c if the PHY is not attached.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds toggling phy reset if PHY is not attached. Otherwise,
some boards (e.g. R-Car H3 Salvator-XS) cannot link up correctly if
we do the following method:
1) Kernel boots by using initramfs.
--> No open the nic, so phy_device_register() and phy_probe()
deasserts the reset.
2) Kernel enters the suspend.
--> So, keep the reset signal as deassert.
--> On R-Car Salvator-XS board, unfortunately, the board power is
turned off.
3) Kernel returns from suspend.
4) ifconfig eth0 up
--> Then, since edge signal of the reset doesn't happen,
it cannot link up.
5) ifconfig eth0 down
6) ifconfig eth0 up
--> In this case, it can link up.
Reported-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes an issue that mdio_bus_phy_resume() doesn't call
phy_resume() if the PHY is not attached.
Fixes: 803dd9c77ac3 ("net: phy: avoid suspending twice a PHY")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This helps separate what capabilities are display capabilities.
v3: Moving display struct right after flags (Lucas)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Suggested-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130232048.14216-2-jose.souza@intel.com
|
|
Right now it is decided if GEN has display by checking the num_pipes,
so lets make it explicit and use a macro.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130232048.14216-1-jose.souza@intel.com
|
|
Once the JITed images for each function in a multi-function program
are generated after the first three JIT passes, we only need to fix
the target address for the branch instruction corresponding to each
bpf-to-bpf function call.
This introduces the following optimizations for reducing the work
done by the JIT compiler when handling multi-function programs:
[1] Instead of doing two extra passes to fix the bpf function calls,
do just one as that would be sufficient.
[2] During the extra pass, only overwrite the instruction sequences
for the bpf-to-bpf function calls as everything else would still
remain exactly the same. This also reduces the number of writes
to the JITed image.
[3] Do not regenerate the prologue and the epilogue during the extra
pass as that would be redundant.
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
In tun.c skb->len was accessed while doing stats accounting after a
call to netif_receive_skb. We can not access skb after this call
because buffers may be dropped.
The fix for this bug would be to store skb->len in local variable and
then use it after netif_receive_skb(). IMO using xdp data size for
accounting bytes will be better because input for tun_xdp_one() is
xdp_buff.
Hence this patch:
- fixes a bug by removing skb access after netif_receive_skb()
- uses xdp data size for accounting bytes
[613.019057] BUG: KASAN: use-after-free in tun_sendmsg+0x77c/0xc50 [tun]
[613.021062] Read of size 4 at addr ffff8881da9ab7c0 by task vhost-1115/1155
[613.023073]
[613.024003] CPU: 0 PID: 1155 Comm: vhost-1115 Not tainted 4.20.0-rc3-vm+ #232
[613.026029] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[613.029116] Call Trace:
[613.031145] dump_stack+0x5b/0x90
[613.032219] print_address_description+0x6c/0x23c
[613.034156] ? tun_sendmsg+0x77c/0xc50 [tun]
[613.036141] kasan_report.cold.5+0x241/0x308
[613.038125] tun_sendmsg+0x77c/0xc50 [tun]
[613.040109] ? tun_get_user+0x1960/0x1960 [tun]
[613.042094] ? __isolate_free_page+0x270/0x270
[613.045173] vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net]
[613.047127] ? peek_head_len.part.13+0x90/0x90 [vhost_net]
[613.049096] ? get_tx_bufs+0x5a/0x2c0 [vhost_net]
[613.051106] ? vhost_enable_notify+0x2d8/0x420 [vhost]
[613.053139] handle_tx_copy+0x2d0/0x8f0 [vhost_net]
[613.053139] ? vhost_net_buf_peek+0x340/0x340 [vhost_net]
[613.053139] ? __mutex_lock+0x8d9/0xb30
[613.053139] ? finish_task_switch+0x8f/0x3f0
[613.053139] ? handle_tx+0x32/0x120 [vhost_net]
[613.053139] ? mutex_trylock+0x110/0x110
[613.053139] ? finish_task_switch+0xcf/0x3f0
[613.053139] ? finish_task_switch+0x240/0x3f0
[613.053139] ? __switch_to_asm+0x34/0x70
[613.053139] ? __switch_to_asm+0x40/0x70
[613.053139] ? __schedule+0x506/0xf10
[613.053139] handle_tx+0xc7/0x120 [vhost_net]
[613.053139] vhost_worker+0x166/0x200 [vhost]
[613.053139] ? vhost_dev_init+0x580/0x580 [vhost]
[613.053139] ? __kthread_parkme+0x77/0x90
[613.053139] ? vhost_dev_init+0x580/0x580 [vhost]
[613.053139] kthread+0x1b1/0x1d0
[613.053139] ? kthread_park+0xb0/0xb0
[613.053139] ret_from_fork+0x35/0x40
[613.088705]
[613.088705] Allocated by task 1155:
[613.088705] kasan_kmalloc+0xbf/0xe0
[613.088705] kmem_cache_alloc+0xdc/0x220
[613.088705] __build_skb+0x2a/0x160
[613.088705] build_skb+0x14/0xc0
[613.088705] tun_sendmsg+0x4f0/0xc50 [tun]
[613.088705] vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net]
[613.088705] handle_tx_copy+0x2d0/0x8f0 [vhost_net]
[613.088705] handle_tx+0xc7/0x120 [vhost_net]
[613.088705] vhost_worker+0x166/0x200 [vhost]
[613.088705] kthread+0x1b1/0x1d0
[613.088705] ret_from_fork+0x35/0x40
[613.088705]
[613.088705] Freed by task 1155:
[613.088705] __kasan_slab_free+0x12e/0x180
[613.088705] kmem_cache_free+0xa0/0x230
[613.088705] ip6_mc_input+0x40f/0x5a0
[613.088705] ipv6_rcv+0xc9/0x1e0
[613.088705] __netif_receive_skb_one_core+0xc1/0x100
[613.088705] netif_receive_skb_internal+0xc4/0x270
[613.088705] br_pass_frame_up+0x2b9/0x2e0
[613.088705] br_handle_frame_finish+0x2fb/0x7a0
[613.088705] br_handle_frame+0x30f/0x6c0
[613.088705] __netif_receive_skb_core+0x61a/0x15b0
[613.088705] __netif_receive_skb_one_core+0x8e/0x100
[613.088705] netif_receive_skb_internal+0xc4/0x270
[613.088705] tun_sendmsg+0x738/0xc50 [tun]
[613.088705] vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net]
[613.088705] handle_tx_copy+0x2d0/0x8f0 [vhost_net]
[613.088705] handle_tx+0xc7/0x120 [vhost_net]
[613.088705] vhost_worker+0x166/0x200 [vhost]
[613.088705] kthread+0x1b1/0x1d0
[613.088705] ret_from_fork+0x35/0x40
[613.088705]
[613.088705] The buggy address belongs to the object at ffff8881da9ab740
[613.088705] which belongs to the cache skbuff_head_cache of size 232
Fixes: 043d222f93ab ("tuntap: accept an array of XDP buffs through sendmsg()")
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When changing mtu many times with traffic, a bug is triggered:
[ 1035.684037] kernel BUG at lib/dynamic_queue_limits.c:26!
[ 1035.684042] invalid opcode: 0000 [#1] SMP
[ 1035.684049] Modules linked in: loop binfmt_misc 8139cp(OE) macsec
tcp_diag udp_diag inet_diag unix_diag af_packet_diag netlink_diag tcp_lp
fuse uinput xt_CHECKSUM iptable_mangle ipt_MASQUERADE
nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4
nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun
bridge stp llc ebtable_filter ebtables ip6table_filter devlink
ip6_tables iptable_filter sunrpc snd_hda_codec_generic snd_hda_intel
snd_hda_codec snd_hda_core snd_hwdep ppdev snd_seq iosf_mbi crc32_pclmul
parport_pc snd_seq_device ghash_clmulni_intel parport snd_pcm
aesni_intel joydev lrw snd_timer virtio_balloon sg gf128mul glue_helper
ablk_helper cryptd snd soundcore i2c_piix4 pcspkr ip_tables xfs
libcrc32c sr_mod sd_mod cdrom crc_t10dif crct10dif_generic ata_generic
[ 1035.684102] pata_acpi virtio_console qxl drm_kms_helper syscopyarea
sysfillrect sysimgblt floppy fb_sys_fops crct10dif_pclmul
crct10dif_common ttm crc32c_intel serio_raw ata_piix drm libata 8139too
virtio_pci drm_panel_orientation_quirks virtio_ring virtio mii dm_mirror
dm_region_hash dm_log dm_mod [last unloaded: 8139cp]
[ 1035.684132] CPU: 9 PID: 25140 Comm: if-mtu-change Kdump: loaded
Tainted: G OE ------------ T 3.10.0-957.el7.x86_64 #1
[ 1035.684134] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 1035.684136] task: ffff8f59b1f5a080 ti: ffff8f5a2e32c000 task.ti:
ffff8f5a2e32c000
[ 1035.684149] RIP: 0010:[<ffffffffba3a40d0>] [<ffffffffba3a40d0>]
dql_completed+0x180/0x190
[ 1035.684162] RSP: 0000:ffff8f5a75483e50 EFLAGS: 00010093
[ 1035.684162] RAX: 00000000000000c2 RBX: ffff8f5a6f91c000 RCX:
0000000000000000
[ 1035.684162] RDX: 0000000000000000 RSI: 0000000000000184 RDI:
ffff8f599fea3ec0
[ 1035.684162] RBP: ffff8f5a75483ea8 R08: 00000000000000c2 R09:
0000000000000000
[ 1035.684162] R10: 00000000000616ef R11: ffff8f5a75483b56 R12:
ffff8f599fea3e00
[ 1035.684162] R13: 0000000000000001 R14: 0000000000000000 R15:
0000000000000184
[ 1035.684162] FS: 00007fa8434de740(0000) GS:ffff8f5a75480000(0000)
knlGS:0000000000000000
[ 1035.684162] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1035.684162] CR2: 00000000004305d0 CR3: 000000024eb66000 CR4:
00000000001406e0
[ 1035.684162] Call Trace:
[ 1035.684162] <IRQ>
[ 1035.684162] [<ffffffffc08cbaf8>] ? cp_interrupt+0x478/0x580 [8139cp]
[ 1035.684162] [<ffffffffba14a294>]
__handle_irq_event_percpu+0x44/0x1c0
[ 1035.684162] [<ffffffffba14a442>] handle_irq_event_percpu+0x32/0x80
[ 1035.684162] [<ffffffffba14a4cc>] handle_irq_event+0x3c/0x60
[ 1035.684162] [<ffffffffba14db29>] handle_fasteoi_irq+0x59/0x110
[ 1035.684162] [<ffffffffba02e554>] handle_irq+0xe4/0x1a0
[ 1035.684162] [<ffffffffba7795dd>] do_IRQ+0x4d/0xf0
[ 1035.684162] [<ffffffffba76b362>] common_interrupt+0x162/0x162
[ 1035.684162] <EOI>
[ 1035.684162] [<ffffffffba0c2ae4>] ? __wake_up_bit+0x24/0x70
[ 1035.684162] [<ffffffffba1e46f5>] ? do_set_pte+0xd5/0x120
[ 1035.684162] [<ffffffffba1b64fb>] unlock_page+0x2b/0x30
[ 1035.684162] [<ffffffffba1e4879>] do_read_fault.isra.61+0x139/0x1b0
[ 1035.684162] [<ffffffffba1e9134>] handle_pte_fault+0x2f4/0xd10
[ 1035.684162] [<ffffffffba1ebc6d>] handle_mm_fault+0x39d/0x9b0
[ 1035.684162] [<ffffffffba76f5e3>] __do_page_fault+0x203/0x500
[ 1035.684162] [<ffffffffba76f9c6>] trace_do_page_fault+0x56/0x150
[ 1035.684162] [<ffffffffba76ef42>] do_async_page_fault+0x22/0xf0
[ 1035.684162] [<ffffffffba76b788>] async_page_fault+0x28/0x30
[ 1035.684162] Code: 54 c7 47 54 ff ff ff ff 44 0f 49 ce 48 8b 35 48 2f
9c 00 48 89 77 58 e9 fe fe ff ff 0f 1f 80 00 00 00 00 41 89 d1 e9 ef fe
ff ff <0f> 0b 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 55 8d 42 ff 48
[ 1035.684162] RIP [<ffffffffba3a40d0>] dql_completed+0x180/0x190
[ 1035.684162] RSP <ffff8f5a75483e50>
It's not the same as in 7fe0ee09 patch described.
As 8139cp uses shared irq mode, other device irq will trigger
cp_interrupt to execute.
cp_change_mtu
-> cp_close
-> cp_open
In cp_close routine just before free_irq(), some interrupt may occur.
In my environment, cp_interrupt exectutes and IntrStatus is 0x4,
exactly TxOk. That will cause cp_tx to wake device queue.
As device queue is started, cp_start_xmit and cp_open will run at same
time which will cause kernel BUG.
For example:
[#] for tx descriptor
At start:
[#][#][#]
num_queued=3
After cp_init_hw->cp_start_hw->netdev_reset_queue:
[#][#][#]
num_queued=0
When 8139cp starts to work then cp_tx will check
num_queued mismatchs the complete_bytes.
The patch will check IntrMask before check IntrStatus in cp_interrupt.
When 8139cp interrupt is disabled, just return.
Signed-off-by: Su Yanjun <suyj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These are missing 'static' so sparse complains:
drivers/clk/meson/vid-pll-div.c:58:26: warning: symbol '_get_table_val' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:1585:12: warning: symbol 'gxbb_vid_pll_parent_names' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:1620:12: warning: symbol 'gxbb_vclk_parent_names' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:1980:12: warning: symbol 'gxbb_cts_parent_names' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:2036:12: warning: symbol 'gxbb_cts_hdmi_tx_parent_names' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Since any page fault may be interrupted by a MMU invalidation and implicit
leaf MR may be released during this process. The check for parent value
is unreliable condition for an implicit MR.
Use other condition that we can rely on to determine if MR is implicit.
Fixes: b4cfe447d47b ("IB/mlx5: Implement on demand paging by adding support for MMU notifiers")
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
The commit marked as fixed didn't do anything wrong, it just copied
existing functionality to the helper which is being fixed now.
Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes,
please pull the following for 4.20:
- Stefan fixes the polariy of the Wi-Fi reset GPIOs signals which would
break on Raspberry Pi 3B and 3B+
* tag 'arm-soc/for-4.20/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2837: Fix polarity of wifi reset GPIOs
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When running with KASAN, the following trace is produced:
[ 62.535888]
==================================================================
[ 62.544930] BUG: KASAN: slab-out-of-bounds in
gut_hw_stats+0x122/0x230 [hfi1]
[ 62.553856] Write of size 8 at addr ffff88080e8d6330 by task
kworker/0:1/14
[ 62.565333] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted
4.19.0-test-build-kasan+ #8
[ 62.575087] Hardware name: Intel Corporation S2600KPR/S2600KPR, BIOS
SE5C610.86B.01.01.0019.101220160604 10/12/2016
[ 62.587951] Workqueue: events work_for_cpu_fn
[ 62.594050] Call Trace:
[ 62.598023] dump_stack+0xc6/0x14c
[ 62.603089] ? dump_stack_print_info.cold.1+0x2f/0x2f
[ 62.610041] ? kmsg_dump_rewind_nolock+0x59/0x59
[ 62.616615] ? get_hw_stats+0x122/0x230 [hfi1]
[ 62.622985] print_address_description+0x6c/0x23c
[ 62.629744] ? get_hw_stats+0x122/0x230 [hfi1]
[ 62.636108] kasan_report.cold.6+0x241/0x308
[ 62.642365] get_hw_stats+0x122/0x230 [hfi1]
[ 62.648703] ? hfi1_alloc_rn+0x40/0x40 [hfi1]
[ 62.655088] ? __kmalloc+0x110/0x240
[ 62.660695] ? hfi1_alloc_rn+0x40/0x40 [hfi1]
[ 62.667142] setup_hw_stats+0xd8/0x430 [ib_core]
[ 62.673972] ? show_hfi+0x50/0x50 [hfi1]
[ 62.680026] ib_device_register_sysfs+0x165/0x180 [ib_core]
[ 62.687995] ib_register_device+0x5a2/0xa10 [ib_core]
[ 62.695340] ? show_hfi+0x50/0x50 [hfi1]
[ 62.701421] ? ib_unregister_device+0x2e0/0x2e0 [ib_core]
[ 62.709222] ? __vmalloc_node_range+0x2d0/0x380
[ 62.716131] ? rvt_driver_mr_init+0x11f/0x2d0 [rdmavt]
[ 62.723735] ? vmalloc_node+0x5c/0x70
[ 62.729697] ? rvt_driver_mr_init+0x11f/0x2d0 [rdmavt]
[ 62.737347] ? rvt_driver_mr_init+0x1f5/0x2d0 [rdmavt]
[ 62.744998] ? __rvt_alloc_mr+0x110/0x110 [rdmavt]
[ 62.752315] ? rvt_rc_error+0x140/0x140 [rdmavt]
[ 62.759434] ? rvt_vma_open+0x30/0x30 [rdmavt]
[ 62.766364] ? mutex_unlock+0x1d/0x40
[ 62.772445] ? kmem_cache_create_usercopy+0x15d/0x230
[ 62.780115] rvt_register_device+0x1f6/0x360 [rdmavt]
[ 62.787823] ? rvt_get_port_immutable+0x180/0x180 [rdmavt]
[ 62.796058] ? __get_txreq+0x400/0x400 [hfi1]
[ 62.802969] ? memcpy+0x34/0x50
[ 62.808611] hfi1_register_ib_device+0xde6/0xeb0 [hfi1]
[ 62.816601] ? hfi1_get_npkeys+0x10/0x10 [hfi1]
[ 62.823760] ? hfi1_init+0x89f/0x9a0 [hfi1]
[ 62.830469] ? hfi1_setup_eagerbufs+0xad0/0xad0 [hfi1]
[ 62.838204] ? pcie_capability_clear_and_set_word+0xcd/0xe0
[ 62.846429] ? pcie_capability_read_word+0xd0/0xd0
[ 62.853791] ? hfi1_pcie_init+0x187/0x4b0 [hfi1]
[ 62.860958] init_one+0x67f/0xae0 [hfi1]
[ 62.867301] ? hfi1_init+0x9a0/0x9a0 [hfi1]
[ 62.873876] ? wait_woken+0x130/0x130
[ 62.879860] ? read_word_at_a_time+0xe/0x20
[ 62.886329] ? strscpy+0x14b/0x280
[ 62.891998] ? hfi1_init+0x9a0/0x9a0 [hfi1]
[ 62.898405] local_pci_probe+0x70/0xd0
[ 62.904295] ? pci_device_shutdown+0x90/0x90
[ 62.910833] work_for_cpu_fn+0x29/0x40
[ 62.916750] process_one_work+0x584/0x960
[ 62.922974] ? rcu_work_rcufn+0x40/0x40
[ 62.928991] ? __schedule+0x396/0xdc0
[ 62.934806] ? __sched_text_start+0x8/0x8
[ 62.941020] ? pick_next_task_fair+0x68b/0xc60
[ 62.947674] ? run_rebalance_domains+0x260/0x260
[ 62.954471] ? __list_add_valid+0x29/0xa0
[ 62.960607] ? move_linked_works+0x1c7/0x230
[ 62.967077] ?
trace_event_raw_event_workqueue_execute_start+0x140/0x140
[ 62.976248] ? mutex_lock+0xa6/0x100
[ 62.982029] ? __mutex_lock_slowpath+0x10/0x10
[ 62.988795] ? __switch_to+0x37a/0x710
[ 62.994731] worker_thread+0x62e/0x9d0
[ 63.000602] ? max_active_store+0xf0/0xf0
[ 63.006828] ? __switch_to_asm+0x40/0x70
[ 63.012932] ? __switch_to_asm+0x34/0x70
[ 63.019013] ? __switch_to_asm+0x40/0x70
[ 63.025042] ? __switch_to_asm+0x34/0x70
[ 63.031030] ? __switch_to_asm+0x40/0x70
[ 63.037006] ? __schedule+0x396/0xdc0
[ 63.042660] ? kmem_cache_alloc_trace+0xf3/0x1f0
[ 63.049323] ? kthread+0x59/0x1d0
[ 63.054594] ? ret_from_fork+0x35/0x40
[ 63.060257] ? __sched_text_start+0x8/0x8
[ 63.066212] ? schedule+0xcf/0x250
[ 63.071529] ? __wake_up_common+0x110/0x350
[ 63.077794] ? __schedule+0xdc0/0xdc0
[ 63.083348] ? wait_woken+0x130/0x130
[ 63.088963] ? finish_task_switch+0x1f1/0x520
[ 63.095258] ? kasan_unpoison_shadow+0x30/0x40
[ 63.101792] ? __init_waitqueue_head+0xa0/0xd0
[ 63.108183] ? replenish_dl_entity.cold.60+0x18/0x18
[ 63.115151] ? _raw_spin_lock_irqsave+0x25/0x50
[ 63.121754] ? max_active_store+0xf0/0xf0
[ 63.127753] kthread+0x1ae/0x1d0
[ 63.132894] ? kthread_bind+0x30/0x30
[ 63.138422] ret_from_fork+0x35/0x40
[ 63.146973] Allocated by task 14:
[ 63.152077] kasan_kmalloc+0xbf/0xe0
[ 63.157471] __kmalloc+0x110/0x240
[ 63.162804] init_cntrs+0x34d/0xdf0 [hfi1]
[ 63.168883] hfi1_init_dd+0x29a3/0x2f90 [hfi1]
[ 63.175244] init_one+0x551/0xae0 [hfi1]
[ 63.181065] local_pci_probe+0x70/0xd0
[ 63.186759] work_for_cpu_fn+0x29/0x40
[ 63.192310] process_one_work+0x584/0x960
[ 63.198163] worker_thread+0x62e/0x9d0
[ 63.203843] kthread+0x1ae/0x1d0
[ 63.208874] ret_from_fork+0x35/0x40
[ 63.217203] Freed by task 1:
[ 63.221844] __kasan_slab_free+0x12e/0x180
[ 63.227844] kfree+0x92/0x1a0
[ 63.232570] single_release+0x3a/0x60
[ 63.238024] __fput+0x1d9/0x480
[ 63.242911] task_work_run+0x139/0x190
[ 63.248440] exit_to_usermode_loop+0x191/0x1a0
[ 63.254814] do_syscall_64+0x301/0x330
[ 63.260283] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 63.270199] The buggy address belongs to the object at
ffff88080e8d5500
which belongs to the cache kmalloc-4096 of size 4096
[ 63.287247] The buggy address is located 3632 bytes inside of
4096-byte region [ffff88080e8d5500, ffff88080e8d6500)
[ 63.303564] The buggy address belongs to the page:
[ 63.310447] page:ffffea00203a3400 count:1 mapcount:0
mapping:ffff88081380e840 index:0x0 compound_mapcount: 0
[ 63.323102] flags: 0x2fffff80008100(slab|head)
[ 63.329775] raw: 002fffff80008100 0000000000000000 0000000100000001
ffff88081380e840
[ 63.340175] raw: 0000000000000000 0000000000070007 00000001ffffffff
0000000000000000
[ 63.350564] page dumped because: kasan: bad access detected
[ 63.361974] Memory state around the buggy address:
[ 63.369137] ffff88080e8d6200: 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00
[ 63.379082] ffff88080e8d6280: 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00
[ 63.389032] >ffff88080e8d6300: 00 00 00 00 00 00 fc fc fc fc fc fc fc
fc fc fc
[ 63.398944] ^
[ 63.406141] ffff88080e8d6380: fc fc fc fc fc fc fc fc fc fc fc fc fc
fc fc fc
[ 63.416109] ffff88080e8d6400: fc fc fc fc fc fc fc fc fc fc fc fc fc
fc fc fc
[ 63.426099]
==================================================================
The trace happens because get_hw_stats() assumes there is room in the
memory allocated in init_cntrs() to accommodate the driver counters.
Unfortunately, that routine only allocated space for the device
counters.
Fix by insuring the allocation has room for the additional driver
counters.
Cc: <Stable@vger.kernel.org> # v4.14+
Fixes: b7481944b06e9 ("IB/hfi1: Show statistics counters under IB stats interface")
Reviewed-by: Mike Marciniczyn <mike.marciniszyn@intel.com>
Reviewed-by: Mike Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Piotr Stankiewicz <piotr.stankiewicz@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
A recent performance enhancement introduced a latency issue in the
HFI message path. The new algorithm removed a forced call send for
PIO messages and added a forced schedule event for messages larger
than the MTU.
For PIO, the schedule path can introduce thrashing that can
significantly impact the throughput for small messages.
If a message size is within the PIO threshold, always take the send
path.
Fixes: 0b79b27748cb ("IB/{hfi1, qib, rdmavt}: Schedule multi RC/UC packets instead of posting")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There's a bug in dtc in checking for duplicate node names when there's
another section (e.g. "/ { };"). In this case, skeleton.dtsi provides
another section. Upon removal of skeleton.dtsi, the dtb fails to build
due to a duplicate node 'fixedregulator@0'. As both nodes were pretty
much the same 3.3V fixed regulator, it hasn't really mattered. Fix this
by renaming the nodes to something unique. In the process, drop the
unit-address which shouldn't be present wtihout reg property.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Move Eric Miao and Haojian Zhuang over to CREDITS, since they're AWOL
for some time already. The git trees have gone away too.
I'm adding myself as a reviewer. I'd like to be Cc'd on patches and will
be able to test them, but I don't possess a data sheet thus there might
be things I'll be unable to review. Hence the Odd-Fixes status.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
cpu_is_mmp2() was equivalent to cpu_is_pj4(), wouldn't be correct for
multiplatform kernels. Fix it by also considering mmp_chip_id, as is
done for cpu_is_pxa168() and cpu_is_pxa910() above.
Moreover, it is only available with CONFIG_CPU_MMP2 and thus doesn't work
on DT-based MMP2 machines. Enable it on CONFIG_MACH_MMP2_DT too.
Note: CONFIG_CPU_MMP2 is only used for machines that use board files
instead of DT. It should perhaps be renamed. I'm not doing it now, because
I don't have a better idea.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into fixes
DT mt7622:
- Kernelci awaits a working stdout-path.
Fix the path for reference board and bananapi-r64
- General propouse timer has issues with clocks that didn't
get probed early. Delete the DT node as the timer isn't
need, a ARM arch timer exists on the system.
* tag 'v4.19-next-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: mt7622: Drop the general purpose timer node
arm64: dts: mt7622: fix no more console output on BPI-R64 board
arm64: dts: mt7622: fix no more console output on rfb1
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add IRC channel and URL of the wiki.
Also add soc drivers folder and regex to catch more
mediatek components.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Fix build errors due to missing <linux/module.h> header file.
The header file is inserted first because module-related errors
begin showing up in <linux/acpi.h> (when CONFIG_ACPI is not set).
Sample of build errors:
In file included from ../include/linux/acpi.h:27:0,
from ../drivers/media/platform/seco-cec/seco-cec.c:10:
../include/linux/device.h:1620:1: warning: data definition has no type or storage class [enabled by default]
module_exit(__driver##_exit);
^
../include/linux/platform_device.h:229:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^
../drivers/media/platform/seco-cec/seco-cec.c:791:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(secocec_driver);
^
../include/linux/device.h:1620:1: error: type defaults to 'int' in declaration of 'module_exit' [-Werror=implicit-int]
module_exit(__driver##_exit);
^
../include/linux/platform_device.h:229:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^
../drivers/media/platform/seco-cec/seco-cec.c:791:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(secocec_driver);
^
In file included from ../include/linux/linkage.h:7:0,
from ../include/linux/kernel.h:7,
from ../include/linux/list.h:9,
from ../include/linux/resource_ext.h:17,
from ../include/linux/acpi.h:26,
from ../drivers/media/platform/seco-cec/seco-cec.c:10:
../include/linux/export.h:18:30: warning: parameter names (without types) in function declaration [enabled by default]
#define THIS_MODULE ((struct module *)0)
^
../include/linux/platform_device.h:199:34: note: in expansion of macro 'THIS_MODULE'
__platform_driver_register(drv, THIS_MODULE)
^
../include/linux/device.h:1613:9: note: in expansion of macro 'platform_driver_register'
return __register(&(__driver) , ##__VA_ARGS__); \
^
../include/linux/platform_device.h:229:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^
../drivers/media/platform/seco-cec/seco-cec.c:791:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(secocec_driver);
^
../drivers/media/platform/seco-cec/seco-cec.c:793:20: error: expected declaration specifiers or '...' before string constant
MODULE_DESCRIPTION("SECO CEC X86 Driver");
^
../drivers/media/platform/seco-cec/seco-cec.c:794:15: error: expected declaration specifiers or '...' before string constant
MODULE_AUTHOR("Ettore Chimenti <ek5.chimenti@gmail.com>");
^
../drivers/media/platform/seco-cec/seco-cec.c:795:16: error: expected declaration specifiers or '...' before string constant
MODULE_LICENSE("Dual BSD/GPL");
^
In file included from ../include/linux/acpi.h:27:0,
from ../drivers/media/platform/seco-cec/seco-cec.c:10:
../drivers/media/platform/seco-cec/seco-cec.c:791:24: warning: 'secocec_driver_init' defined but not used [-Wunused-function]
module_platform_driver(secocec_driver);
^
../include/linux/device.h:1611:19: note: in definition of macro 'module_driver'
static int __init __driver##_init(void) \
^
../drivers/media/platform/seco-cec/seco-cec.c:791:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(secocec_driver);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Ettore Chimenti <ek5.chimenti@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The state structure contains the resolution expected by the decoder
and encoder. For an encoder that resolution should be taken from the
OUTPUT format, and for a decoder from the CAPTURE format.
If the wrong format is picked, a buffer overrun can occur if there is
a mismatch between the CAPTURE and OUTPUT formats.
The real fix would be to correctly implement the stateful codec
specification, but that will take more time. For now just prevent the
buffer overrun.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If start_streaming() fails and all queued buffers are returned to
vb2, then do not call v4l2_ctrl_request_complete(). Nothing happened
to the request and the state should remain as it was before
start_streaming was called.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
When a buffer is returned to state QUEUED (that happens when
start_streaming fails), then do not unbind and put the object
from the request. Nothing has changed yet, so just keep it as
is.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
When vb2_buffer_done is called the buffer is unbound from the
request and put. The media_request_object_put also 'put's the
request reference. If the application has already closed the
request fd, then that means that the request reference at that
point goes to 0 and the whole request is released.
This means that the control handler associated with the request is
also freed and that causes this kernel oops:
[174705.995401] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:908
[174705.995411] in_atomic(): 1, irqs_disabled(): 1, pid: 28071, name: vivid-000-vid-o
[174705.995416] 2 locks held by vivid-000-vid-o/28071:
[174705.995420] #0: 000000001ea3a232 (&dev->mutex#3){....}, at: vivid_thread_vid_out+0x3f5/0x550 [vivid]
[174705.995447] #1: 00000000e30a0d1e (&(&q->done_lock)->rlock){....}, at: vb2_buffer_done+0x92/0x1d0 [videobuf2_common]
[174705.995460] Preemption disabled at:
[174705.995461] [<0000000000000000>] (null)
[174705.995472] CPU: 11 PID: 28071 Comm: vivid-000-vid-o Tainted: G W 4.20.0-rc1-test-no #88
[174705.995476] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 05/19/2017
[174705.995481] Call Trace:
[174705.995500] dump_stack+0x46/0x60
[174705.995512] ___might_sleep.cold.79+0xe1/0xf1
[174705.995523] __mutex_lock+0x50/0x8f0
[174705.995531] ? find_held_lock+0x2d/0x90
[174705.995536] ? find_held_lock+0x2d/0x90
[174705.995542] ? find_held_lock+0x2d/0x90
[174705.995564] ? v4l2_ctrl_handler_free.part.13+0x44/0x1d0 [videodev]
[174705.995576] v4l2_ctrl_handler_free.part.13+0x44/0x1d0 [videodev]
[174705.995590] v4l2_ctrl_request_release+0x1c/0x30 [videodev]
[174705.995600] media_request_clean+0x64/0xe0 [media]
[174705.995609] media_request_release+0x19/0x40 [media]
[174705.995617] vb2_buffer_done+0xef/0x1d0 [videobuf2_common]
[174705.995630] vivid_thread_vid_out+0x2c1/0x550 [vivid]
[174705.995645] ? vivid_stop_generating_vid_cap+0x1c0/0x1c0 [vivid]
[174705.995653] kthread+0x113/0x130
[174705.995659] ? kthread_park+0x80/0x80
[174705.995667] ret_from_fork+0x35/0x40
The vb2_buffer_done function can be called from interrupt context, so
anything that sleeps is not allowed.
The solution is to increment the request refcount when the buffer is
queued and decrement it when the buffer is dequeued. Releasing the
request is fine if that happens from VIDIOC_DQBUF.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
VIDIOC_PREPARE_BUF should ignore V4L2_BUF_FLAG_REQUEST_FD since it isn't
doing anything with requests. So inform vb2_queue_or_prepare_buf whether
it is called from vb2_prepare_buf or vb2_qbuf and just return 0 in the
first case.
This was found when adding new v4l2-compliance checks.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
vb2_start_streaming() already rolls back the buffers, so there is no
need to call __vb2_queue_cancel(). Especially since __vb2_queue_cancel()
does too much, such as zeroing the q->queued_count value, causing vb2
to think that no buffers have been queued.
It appears that this call to __vb2_queue_cancel() is a left-over from
before commit b3379c6201bb3.
Fixes: b3379c6201bb3 ('vb2: only call start_streaming if sufficient buffers are queued')
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v4.16 and up
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The devm_ioremap_resource() function doesn't return NULL pointers, it
returns error pointers.
Fixes: 50e761516f2b ("media: platform: Add Cedrus VPU decoder driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Commit de2bc45c84f7 ("media: vsp1: Update LIF buffer thresholds")
updated the LIF buffer thresholds based on the VSP version, but used the
wrong model mask. This resulted in all VSP instances to be treated as a
Gen3 VSPD, breaking operation on all Gen2 platforms as well as on
H3 ES2.0, M3-N, V3M and V3H. Fix it.
Fixes: de2bc45c84f7 ("media: vsp1: Update LIF buffer thresholds")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
These devices support read zero after trim (RZAT), as they advertise to
the OS. However, the OS doesn't believe the SSDs unless they are
explicitly whitelisted.
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fix the intel_link_compute_m_n in case of display stream
compression. This patch passes the compressed_bpp to
intel_link_compute_m_n if compression is enabled.
Fixes: a4a157777c80 ("drm/i915/dp: Compute DSC pipe config in atomic check")
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181201010412.32372-1-manasi.d.navare@intel.com
|
|
The commit b1b8f45b3130 ("ARM: dts: bcm2837: Add missing GPIOs of Expander")
introduced a wifi power sequence. Unfortunately the polarity of the reset
GPIOs were wrong and broke the wifi support on Raspberry Pi 3 B and
later in 3 B+. This wasn't discovered before since the power sequence
takes only effect in case the relevant MMC driver is compiled as a module.
Fixes: b1b8f45b3130 ("ARM: dts: bcm2837: Add missing GPIOs of Expander")
Cc: stable@vger.kernel.org
Reported-by: Matthias Lueschner <lueschem@gmail.com>
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=911443
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
clk-meson
Pull amlogic meson clk driver updates from Neil Armstrong:
- Add GX video clocks
- Switch to HHI syscon for meson8b
- Fix meson8b cpu clock
- Add support for meson8b CPU scaling
- Add Meson8b CPU post-dividers clocks
* tag 'meson-clk-4.21-1' of https://github.com/BayLibre/clk-meson:
clk: meson: meson8b: add the CPU clock post divider clocks
clk: meson: meson8b: rename cpu_div2/cpu_div3 to cpu_in_div2/cpu_in_div3
clk: meson: clk-regmap: add read-only gate ops
clk: meson: meson8b: allow changing the CPU clock tree
clk: meson: meson8b: run from the XTAL when changing the CPU frequency
clk: meson: meson8b: add support for more M/N values in sys_pll
clk: meson: meson8b: mark the CPU clock as CLK_IS_CRITICAL
clk: meson: meson8b: do not use cpu_div3 for cpu_scale_out_sel
clk: meson: clk-pll: check if the clock is already enabled
clk: meson: meson8b: fix the width of the cpu_scale_div clock
clk: meson: meson8b: fix incorrect divider mapping in cpu_scale_table
clk: meson: meson8b: use the HHI syscon if available
dt-bindings: clock: meson8b: use the registers from the HHI syscon
clk: meson-gxbb: Add video clocks
dt-bindings: clk: meson-gxbb: Add Video clock bindings
clk: meson-gxbb: Fix HDMI PLL for GXL SoCs
clk: meson: Add vid_pll divider driver
dt-bindings: clock: meson8b: export the CPU post dividers
|
|
With the GREY format at the beginning, the default format selected
by vicodec would be GREY instead of YUV420. That didn't make sense,
so move it to the end of the list.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
There is a spelling mistake in the module description as well
as a comment. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add a new vivid button control to inject an error into the
req_validate request callback.
This will help testing with v4l2-compliance.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
On older Kernels (prior to 4.15) irqreturn_t and devm_request_threaded_irq
is not defined when compiling adv7604.c. It seems more recent Kernels
include it via another header which is included by adv7604.c.
Now we include linux/interrupt.h explicitly to get the type also defined
for Kernels prior to 4.15.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Commit 0185f8501762 ("[media] samples: v4l: from Documentation to
samples directory") moved the v4l2-pci-skeleton driver to the samples
directory. The samples are only be built, if CONFIG_SAMPLES is enabled.
Therefore, VIDEO_PCI_SKELETON is not enough to build the
v4l2-pci-skeleton driver, but SAMPLES needs to be enabled, too. Let
VIDEO_PCI_SKELETON depend on SAMPLES.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Commit 2d7007153f0c ("[media] media: videobuf2: Restructure vb2_buffer")
replaced vb2_buffer with vb2_v4l2_buffer in all v4l2 drivers. The
restructuring skipped the v4l2-pci-skeleton, probably because it resides
outside the drivers directory.
The v4l2_buf_ops assume that the passed buffer is a vb2_v4l2_buffer.
This is not the case if the skel_buffer is based on vb2_buffer instead
of vb2_v4l2_buffer.
Replace vb2_buffer with vb2_v4l2_buffer in the skeleton to make sure
that future drivers that are based on the skeleton use vb2_v4l2_buffer.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The v4l_fill_fmtdesc() function does a good job in filling in pixelformat
description. While generally all drivers should depend on this function
doing the job, staging drivers that use their own formats may not.
Allow staging drivers to fill in their own formats by checking whether the
description begins with a non-nil character before issuing the warning.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Suggested-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
intra_dc_precision is a 2-bit integer [1]
allow use of all valid options, 8 - 11 bits precision
[1] ISO/IEC 13818-2 Table 6-13
Fixes: c27bb30e7b6d ("media: v4l: Add definitions for MPEG-2 slice format and metadata")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
We lose even config space access when we power gate the ISP
via the PUNIT. That makes lspci & co. produce gibberish.
To fix that let's try to implement actual runtime pm hooks
and inform the pci core that the device always goes to
D3cold. That will cause the pci core to resume the device
before attempting config space access.
This introduces another annoyance though. We get the
following error every time we try to resume the device:
intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
The reason being that the pci core tries to put the device
back into D0 via the standard PCI PM mechanism before
calling the driver resume hook. To fix this properly
we'd need to infiltrate the platform pm hooks (could
turn ugly real fast), or use pm domains (which don't
seem to exist on x86), or some extra early resume
hook for the driver (which doesn't exist either).
So maybe we just choose to live with the error?
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
|
|
If the ISP is exposed as a PCI device VLV machines need the
same treatment as CHV machines to power gate the ISP. Otherwise
s0ix will not work.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
At ->remove() stage we know that device had been instantiated properly,
so, it can't be an invalid pointer to the driver data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
NULL check before some freeing functions is not needed.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
As Greg KH explained in:
https://lkml.org/lkml/2015/8/15/114
There no need to check the return value of debugfs_create_file() and
debugfs_create_dir().
This also fix static code checker warnings:
drivers/platform/x86/intel_ips.c:1314
ips_debugfs_init() warn: passing zero to 'PTR_ERR'
drivers/platform/x86/intel_ips.c:1328
ips_debugfs_init() warn: passing zero to 'PTR_ERR'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
ACPI provides a generic helper to get I2C Serial Bus resources.
Use it instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ACPI device with INT3515 _HID is representing a complex USB PD
hardware infrastructure which includes several I2C slave ICs.
We add an ID to the I2C multi instantiate list to enumerate
all I2C slaves correctly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
