| Age | Commit message (Collapse) | Author |
|---|
|
Make hmac_tfm static since it's not used anywhere else besides the file
it is in.
Remove declaration of hash_tfm since it doesn't exist.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
|
|
Return INTEGRITY_PASS for the enum integrity_status rather than 0.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
|
|
In AST2600, the unit of SPI CEx decoding range register is 1MB, and end
address offset is set to the acctual offset - 1MB. If the flash only has
1MB, the end address will has same value as start address, which will
causing unexpected errors.
This patch set the decoding size to at least 2MB to avoid decoding errors.
Tested:
root@bletchley:~# dmesg | grep "aspeed-smc 1e631000.spi: CE0 window"
[ 59.328134] aspeed-smc 1e631000.spi: CE0 window resized to 2MB (AST2600 Decoding)
[ 59.343001] aspeed-smc 1e631000.spi: CE0 window [ 0x50000000 - 0x50200000 ] 2MB
root@bletchley:~# devmem 0x1e631030
0x00100000
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
[ clg : Ported on new spi-mem driver ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-12-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To accommodate the different response time of SPI transfers on different
boards and different SPI NOR devices, the Aspeed controllers provide a
set of Read Timing Compensation registers to tune the timing delays
depending on the frequency being used. The AST2600 SoC has one of these
registers per device. On the AST2500 and AST2400 SoCs, the timing
register is shared by all devices which is problematic to get good
results other than for one device.
The algorithm first reads a golden buffer at low speed and then performs
reads with different clocks and delay cycle settings to find a breaking
point. This selects a default good frequency for the CEx control register.
The current settings are a bit optimistic as we pick the first delay giving
good results. A safer approach would be to determine an interval and
choose the middle value.
Calibration is performed when the direct mapping for reads is created.
Since the underlying spi-nor object needs to be initialized to create
the spi_mem operation for direct mapping, we should be fine. Having a
specific API would clarify the requirements though.
Cc: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-9-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Extend the driver for the AST2400 SPI Flash Controller (SPI). This
controller has a slightly different interface which requires
adaptation of the 4B handling. Summary of features :
. host Firmware
. 1 chip select pin (CE0)
. slightly different register set, between AST2500 and the legacy
controller
. no segment registers
. single, dual mode.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-8-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is not possible to configure a full 128MB window for a chip of the
same size on the AST2500 SPI controller. For this case, the maximum
window size is restricted to 120MB for CE0.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-7-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The segment registers of the FMC/SPI controllers provide a way to
configure the mapping window of the flash device contents on the AHB
bus. Adjust this window to the size of the spi-mem mapping.
Things get more complex with multiple devices. The driver needs to
also adjust the window of the next device to make sure that there is
no overlap, even if there is no available device. The proposal below
is not perfect but it is covering all the cases we have seen on
different boards with one and two devices on the same bus.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-6-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use direct mapping to read the flash device contents. This operation
mode is called "Command mode" on Aspeed SoC SMC controllers. It uses a
Control Register for the settings to apply when a memory operation is
performed on the flash device mapping window.
If the window is not big enough, fall back to the "User mode" to
perform the read.
Direct mapping for writes will come later when validated.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-5-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This SPI driver adds support for the Aspeed static memory controllers
of the AST2600, AST2500 and AST2400 SoCs using the spi-mem interface.
* AST2600 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. Only supports SPI type flash memory
. different segment register interface
. single, dual and quad mode.
* AST2600 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. different segment register interface
. single, dual and quad mode.
* AST2500 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the driver
. single, dual mode.
* AST2500 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. single, dual mode.
* AST2400 New Static Memory Controller (also referred as FMC)
. BMC firmware
. New register set
. 5 chip select pins (CE0 ∼ CE4)
. supports NOR flash, NAND flash and SPI flash memory.
. single, dual and quad mode.
Each controller has a memory range on which flash devices contents are
mapped. Each device is assigned a window that can be changed at bootime
with the Segment Address Registers.
Each SPI flash device can then be accessed in two modes: Command and
User. When in User mode, SPI transfers are initiated with accesses to
the memory segment of a device. When in Command mode, memory
operations on the memory segment of a device generate SPI commands
automatically using a Control Register for the settings.
This initial patch adds support for User mode. Command mode needs a little
more work to check that the memory window on the AHB bus fits the device
size. It will come later when support for direct mapping is added.
Single and dual mode RX transfers are supported. Other types than SPI
are not supported.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-4-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The "interrupt" property is optional because it is only necessary for
controllers supporting DMAs (Not implemented yet in the new driver).
Cc: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-3-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a logic error when removing rt5645 device as the function
rt5645_i2c_remove() first cancel the &rt5645->jack_detect_work and
delete the &rt5645->btn_check_timer latter. However, since the timer
handler rt5645_btn_check_callback() will re-queue the jack_detect_work,
this cleanup order is buggy.
That is, once the del_timer_sync in rt5645_i2c_remove is concurrently
run with the rt5645_btn_check_callback, the canceled jack_detect_work
will be rescheduled again, leading to possible use-after-free.
This patch fix the issue by placing the del_timer_sync function before
the cancel_delayed_work_sync.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Link: https://lore.kernel.org/r/20220516092035.28283-1-linma@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently the checking for if a component sits on the CPU or CODEC side
of the DAI link is done with a helper function that checks if the
component defines legacy_dai_naming. However, there are already a couple
of CPU side components that explicitly opt in to non-legacy DAI naming
and it doesn't seem like a very robust solution. Rather than looking for
the flag check if the component is attached to any of the CODEC DAIs on
the DAI link. This is more robust and helps to bring the core further in
the direction of a component being a generic block rather than being
classified as platform or CODEC drivers.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220513090532.1450944-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Passing the result of the helper function snd_soc_component_is_codec
to snd_soc_register_dai is less clear than just passing the DAI
naming flag directly. snd_soc_register_dai wants to know if it
should use the legacy DAI naming. The CODEC distinction is more
of a historical thing and not obviously directly related, and there
are already a couple of CPU side components that explicitly opt in
to non-legacy DAI naming.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220513090532.1450944-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220513090532.1450944-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 6748d0559059 ("ASoC: ti: Add custom machine driver for j721e EVM (CPB and IVI)")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220512111331.44774-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove duplicated includes.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20220514023806.34768-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
mt8186 DSP uses two hardware mailbox IP to communicate with AP.
One mailbox is used for requests coming from AP, and the other
one is for requests from DSP.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Link: https://lore.kernel.org/r/20220512082215.3018-4-tinghan.shen@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds mt8195 IPC support by using mailbox.
On mt8195 resource, there are two mboxes used to handle ipc request
and reply. We create a mtk-adsp-ipc client device to request mbox
controllers.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220512082215.3018-3-tinghan.shen@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some of mediatek processors contain
the Tensilica HiFix DSP for audio processing.
The communication between Host CPU and DSP firmware is
taking place using a shared memory area for message passing.
ADSP IPC protocol offers (send/recv) interfaces using
mediatek-mailbox APIs.
We use two mbox channels to implement a request-reply protocol.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Signed-off-by: TingHan Shen <tinghan.shen@mediatek.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Reviewed-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220512082215.3018-2-tinghan.shen@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add i.MX8ULP specific soc data, the max register is FSL_SAI_RTCAP
the IP version is also 0x0301, So version can't be used for the
condition of register FSL_SAI_MCTL setting.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1652688372-10274-4-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add i.MX8M Plus specific soc data, the max register is FSL_SAI_MDIV.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1652688372-10274-3-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On i.MX8MM the max register is FSL_SAI_MCTL, which is
different with previous platform, so add max_register in
soc data to distinguish platforms.
And add specific soc data for i.MX8MM
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1652688372-10274-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ERROR check is already in clk_disable() and clk_unprepare() by using
IS_ERR_OR_NULL. Remove unneeded ERROR check for ftide->pclk here.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
They are either obsolete or useless.
Those in the normal processing path cannot be enabled on a production
system; they generate too much noise.
One pr_debug call resides in an error path and does provide useful info,
merge it with the existing nf_log_invalid().
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Currently nf_conncount can trigger garbage collection (GC)
at multiple places. Each GC process takes a spin_lock_bh
to traverse the nf_conncount_list. We found that when testing
port scanning use two parallel nmap, because the number of
connection increase fast, the nf_conncount_count and its
subsequent call to __nf_conncount_add take too much time,
causing several CPU lockup. This happens when user set the
conntrack limit to +20,000, because the larger the limit,
the longer the list that GC has to traverse.
The patch mitigate the performance issue by avoiding unnecessary
GC with a timestamp. Whenever nf_conncount has done a GC,
a timestamp is updated, and beforce the next time GC is
triggered, we make sure it's more than a jiffies.
By doin this we can greatly reduce the CPU cycles and
avoid the softirq lockup.
To reproduce it in OVS,
$ ovs-appctl dpctl/ct-set-limits zone=1,limit=20000
$ ovs-appctl dpctl/ct-get-limits
At another machine, runs two nmap
$ nmap -p1- <IP>
$ nmap -p1- <IP>
Signed-off-by: William Tu <u9012063@gmail.com>
Co-authored-by: Yifeng Sun <pkusunyifeng@gmail.com>
Reported-by: Greg Rose <gvrose8192@gmail.com>
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Commit 40867d74c374 ("net: Add l3mdev index to flow struct and avoid oif
reset for port devices") introduces a flow key specific for layer 3
domains, such as a VRF master device. This allows for explicit VRF domain
selection instead of abusing the oif flow key.
Update ip[6]_route_me_harder() to make use of that new key when re-routing
mangled packets within VRFs instead of setting the flow oif, making it
consistent with other users.
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When running a combination of PPPoE on top of a VLAN, we need to set
info->outdev to the PPPoE device, otherwise PPPoE encap is skipped
during software offload.
Fixes: 72efd585f714 ("netfilter: flowtable: add pppoe support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When calling dev_fill_forward_path on a pppoe device, the provided destination
address is invalid. In order for the bridge fdb lookup to succeed, the pppoe
code needs to update ctx->daddr to the correct value.
Fix this by storing the address inside struct net_device_path_ctx
Fixes: f6efc675c9dd ("net: ppp: resolve forwarding path for bridge pppoe devices")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The dst entry does not contain a valid hardware address, so skip the lookup
in order to avoid running into errors here.
The proper hardware address is filled in from nft_dev_path_info
Fixes: 72efd585f714 ("netfilter: flowtable: add pppoe support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
If a flow cannot be offloaded, the code currently repeatedly tries again as
quickly as possible, which can significantly increase system load.
Fix this by limiting flow timeout update and hardware offload retry to once
per second.
Fixes: c07531c01d82 ("netfilter: flowtable: Remove redundant hw refresh bit")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When a clock source is connected to multiple nodes / endpoints, the
current USB-audio driver tries to set up at each time one of them is
configured. Although it reads the current rate and updates only if it
differs, some devices seem unhappy with this behavior and spew the
errors when reading/updating the rate unnecessarily.
This patch tries to reduce the redundant clock setup by introducing a
refcount for each clock source. When the stream is actually running,
a clock rate is "locked", and it bypasses the clock and/or refuse to
change any longer.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215934
Link: https://lore.kernel.org/r/20220516104807.16482-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
syzbot was able to trigger an Out-of-Bound on the pedit action:
UBSAN: shift-out-of-bounds in net/sched/act_pedit.c:238:43
shift exponent 1400735974 is too large for 32-bit type 'unsigned int'
CPU: 0 PID: 3606 Comm: syz-executor151 Not tainted 5.18.0-rc5-syzkaller-00165-g810c2f0a3f86 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
ubsan_epilogue+0xb/0x50 lib/ubsan.c:151
__ubsan_handle_shift_out_of_bounds.cold+0xb1/0x187 lib/ubsan.c:322
tcf_pedit_init.cold+0x1a/0x1f net/sched/act_pedit.c:238
tcf_action_init_1+0x414/0x690 net/sched/act_api.c:1367
tcf_action_init+0x530/0x8d0 net/sched/act_api.c:1432
tcf_action_add+0xf9/0x480 net/sched/act_api.c:1956
tc_ctl_action+0x346/0x470 net/sched/act_api.c:2015
rtnetlink_rcv_msg+0x413/0xb80 net/core/rtnetlink.c:5993
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:725
____sys_sendmsg+0x6e2/0x800 net/socket.c:2413
___sys_sendmsg+0xf3/0x170 net/socket.c:2467
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2496
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fe36e9e1b59
Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffef796fe88 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fe36e9e1b59
RDX: 0000000000000000 RSI: 0000000020000300 RDI: 0000000000000003
RBP: 00007fe36e9a5d00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fe36e9a5d90
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
The 'shift' field is not validated, and any value above 31 will
trigger out-of-bounds. The issue predates the git history, but
syzbot was able to trigger it only after the commit mentioned in
the fixes tag, and this change only applies on top of such commit.
Address the issue bounding the 'shift' value to the maximum allowed
by the relevant operator.
Reported-and-tested-by: syzbot+8ed8fc4c57e9dcf23ca6@syzkaller.appspotmail.com
Fixes: 8b796475fd78 ("net/sched: act_pedit: really ensure the skb is writable")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
t7xx_dl_add_timedout() now return int 'ret', but the return type
is bool. Change the return type to int for furthor errcode upstream.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At cleaning up and moving the device rename from the quirk table to
its own table, we removed the entry for Rane SL-1 as we thought it's
only for renaming. It turned out, however, that the quirk is required
for matching with the device that declares itself as no standard
audio but only as vendor-specific.
Restore the quirk entry for Rane SL-1 to fix the regression.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215887
Fixes: 5436f59bc5bc ("ALSA: usb-audio: Move device rename and profile quirks to an internal table")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220516103112.12950-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
vfree(NULL) is safe. NULL check before vfree() is not needed.
Delete them to simplify the code.
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
octep_init_module misses destroy_workqueue in error path,
this patch fixes that.
Fixes: 862cd659a6fb ("octeon_ep: Add driver framework and device initialization")
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric Dumazet says:
====================
net: polish skb defer freeing
While testing this recently added feature on a variety
of platforms/configurations, I found the following issues:
1) A race leading to concurrent calls to smp_call_function_single_async()
2) Missed opportunity to use napi_consume_skb()
3) Need to limit the max length of the per-cpu lists.
4) Process the per-cpu list more frequently, for the
(unusual) case where net_rx_action() has mutiple
napi_poll() to process per round.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_defer_free_flush() can consume cpu cycles,
it seems better to call it in the inner loop:
- Potentially frees page/skb that will be reallocated while hot.
- Account for the cpu cycles in the @time_limit determination.
- Keep softnet_data.defer_count small to reduce chances for
skb_attempt_defer_free() to send an IPI.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 68822bdf76f1 ("net: generalize skb freeing
deferral to per-cpu lists") added another per-cpu
cache of skbs. It was expected to be small,
and an IPI was forced whenever the list reached 128
skbs.
We might need to be able to control more precisely
queue capacity and added latency.
An IPI is generated whenever queue reaches half capacity.
Default value of the new limit is 64.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_defer_free_flush() runs from softirq context,
we have the opportunity to refill the napi_alloc_cache,
and/or use kmem_cache_free_bulk() when this cache is full.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A cpu can observe sd->defer_count reaching 128,
and call smp_call_function_single_async()
Problem is that the remote CPU can clear sd->defer_count
before the IPI is run/acknowledged.
Other cpus can queue more packets and also decide
to call smp_call_function_single_async() while the pending
IPI was not yet delivered.
This is a common issue with smp_call_function_single_async().
Callers must ensure correct synchronization and serialization.
I triggered this issue while experimenting smaller threshold.
Performing the call to smp_call_function_single_async()
under sd->defer_lock protection did not solve the problem.
Commit 5a18ceca6350 ("smp: Allow smp_call_function_single_async()
to insert locked csd") replaced an informative WARN_ON_ONCE()
with a return of -EBUSY, which is often ignored.
Test of CSD_FLAG_LOCK presence is racy anyway.
Fixes: 68822bdf76f1 ("net: generalize skb freeing deferral to per-cpu lists")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Works fine on my HP C3600:
[ 274.452394] tulip0: no phy info, aborting mtable build
[ 274.499041] tulip0: MII transceiver #1 config 1000 status 782d advertising 01e1
[ 274.750691] net eth0: Digital DS21142/43 Tulip rev 65 at MMIO 0xf4008000, 00:30:6e:08:7d:21, IRQ 17
[ 283.104520] net eth0: Setting full-duplex based on MII#1 link partner capability of c1e1
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ath.git patches for v5.19. Major changes:
ath11k
* enable keepalive during WoWLAN suspend
* implement remain-on-channel support
|
|
mt76 patches for 5.19
- tx locking improvements
- wireless ethernet dispatch support for flow offload
- non-standard VHT MCS10-11 support
- fixes
- runtime PM improvements
- mt7921 AP mode support
- mt7921 ipv6 NS offload support
|
|
hinic_pf_to_mgmt_init misses destroy_workqueue in error path,
this patch fixes that.
Fixes: 6dbb89014dc3 ("hinic: fix sending mailbox timeout in aeq event work")
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Menglong Dong says:
====================
net: skb: check the boundrary of skb drop reason
In the commit 1330b6ef3313 ("skb: make drop reason booleanable"),
SKB_NOT_DROPPED_YET is added to the enum skb_drop_reason, which makes
the invalid drop reason SKB_NOT_DROPPED_YET can leak to the kfree_skb
tracepoint. Once this happen (it happened, as 4th patch says), it can
cause NULL pointer in drop monitor and result in kernel panic.
Therefore, check the boundrary of drop reason in both kfree_skb_reason
(2th patch) and drop monitor (1th patch) to prevent such case happens
again.
Meanwhile, fix the invalid drop reason passed to kfree_skb_reason() in
tcp_v4_rcv() and tcp_v6_rcv().
Changes since v2:
1/4 - don't reset the reason and print the debug warning only (Jakub
Kicinski)
4/4 - remove new lines between tags
Changes since v1:
- consider tcp_v6_rcv() in the 4th patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'drop_reason' that passed to kfree_skb_reason() in tcp_v4_rcv()
and tcp_v6_rcv() can be SKB_NOT_DROPPED_YET(0), as it is used as the
return value of tcp_inbound_md5_hash().
And it can panic the kernel with NULL pointer in
net_dm_packet_report_size() if the reason is 0, as drop_reasons[0]
is NULL.
Fixes: 1330b6ef3313 ("skb: make drop reason booleanable")
Reviewed-by: Jiang Biao <benbjiang@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SKB_DR_OR() is used to set the drop reason to a value when it is
not set or specified yet. SKB_NOT_DROPPED_YET should also be considered
as not set.
Reviewed-by: Jiang Biao <benbjiang@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sometimes, we may forget to reset skb drop reason to NOT_SPECIFIED after
we make it the return value of the functions with return type of enum
skb_drop_reason, such as tcp_inbound_md5_hash. Therefore, its value can
be SKB_NOT_DROPPED_YET(0), which is invalid for kfree_skb_reason().
So we check the range of drop reason in kfree_skb_reason() with
DEBUG_NET_WARN_ON_ONCE().
Reviewed-by: Jiang Biao <benbjiang@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
