summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-03-18drm/i915: introduce REG_BIT() and REG_GENMASK() to define register contentsJani Nikula
Introduce REG_BIT(n) to define register bits and REG_GENMASK(h, l) to define register bitfield masks. We define the above as wrappers to BIT() and GENMASK() respectively to force u32 type to go with our register size, and to add compile time checks on the bit numbers. The intention is that these are easier to get right and review against the spec than hand rolled masks. Convert power sequencer registers as an example. v4: - rebase v3: - rename macros to REG_BIT() and REG_GENMASK() to avoid underscore prefix and to be in line with kernel macros (Chris) - add compile time checks (Mika) v2: - rename macros to just _BIT() and _MASK() to reduce verbosity Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/787307c0ba9bc23471e5ff1e454b8af35771fa37.1552657998.git.jani.nikula@intel.com
2019-03-18thermal/intel_powerclamp: fix truncated kthread nameZhang Rui
kthread name only allows 15 characters (TASK_COMMON_LEN is 16). Thus rename the kthreads created by intel_powerclamp driver from "kidle_inject/ + decimal cpuid" to "kidle_inj/ + decimal cpuid" to avoid truncated kthead name for cpu 100 and later. Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2019-03-18thermal: mtk: Allocate enough space for mtk_thermal.Pi-Hsun Shih
The mtk_thermal struct contains a 'struct mtk_thermal_bank banks[];', but the allocation only allocates sizeof(struct mtk_thermal) bytes, which cause out of bound access with the ->banks[] member. Change it to a fixed size array instead. Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org> Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2019-03-18loop: access lo_backing_file only when the loop device is Lo_boundDongli Zhang
Commit 758a58d0bc67 ("loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()") separates "lo->lo_backing_file = NULL" and "lo->lo_state = Lo_unbound" into different critical regions protected by loop_ctl_mutex. However, there is below race that the NULL lo->lo_backing_file would be accessed when the backend of a loop is another loop device, e.g., loop0's backend is a file, while loop1's backend is loop0. loop0's backend is file loop1's backend is loop0 __loop_clr_fd() mutex_lock(&loop_ctl_mutex); lo->lo_backing_file = NULL; --> set to NULL mutex_unlock(&loop_ctl_mutex); loop_set_fd() mutex_lock_killable(&loop_ctl_mutex); loop_validate_file() f = l->lo_backing_file; --> NULL access if loop0 is not Lo_unbound mutex_lock(&loop_ctl_mutex); lo->lo_state = Lo_unbound; mutex_unlock(&loop_ctl_mutex); lo->lo_backing_file should be accessed only when the loop device is Lo_bound. In fact, the problem has been introduced already in commit 7ccd0791d985 ("loop: Push loop_ctl_mutex down into loop_clr_fd()") after which loop_validate_file() could see devices in Lo_rundown state with which it did not count. It was harmless at that point but still. Fixes: 7ccd0791d985 ("loop: Push loop_ctl_mutex down into loop_clr_fd()") Reported-by: syzbot+9bdc1adc1c55e7fe765b@syzkaller.appspotmail.com Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-03-18blk-mq: use blk_mq_sched_mark_restart_hctx to set RESTARTYufen Yu
Let blk_mq_mark_tag_wait() use the blk_mq_sched_mark_restart_hctx() to set BLK_MQ_S_SCHED_RESTART. Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-03-18thermal/int340x_thermal: fix mode settingMatthew Garrett
int3400 only pushes the UUID into the firmware when the mode is flipped to "enable". The current code only exposes the mode flag if the firmware supports the PASSIVE_1 UUID, which not all machines do. Remove the restriction. Signed-off-by: Matthew Garrett <mjg59@google.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2019-03-18thermal/int340x_thermal: Add additional UUIDsMatthew Garrett
Add more supported DPTF policies than the driver currently exposes. Signed-off-by: Matthew Garrett <mjg59@google.com> Cc: Nisha Aram <nisha.aram@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2019-03-18thermal: cpu_cooling: Remove unused cur_freq variableShaokun Zhang
The 'cur_freq' local variable became unused after commit 84fe2cab4859 ("cpu_cooling: Drop static-power related stuff"), let's remove it. Cc: Amit Daniel Kachhap <amit.kachhap@gmail.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Javi Merino <javi.merino@kernel.org> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2019-03-18thermal: bcm2835: Fix crash in bcm2835_thermal_debugfsPhil Elwell
"cat /sys/kernel/debug/bcm2835_thermal/regset" causes a NULL pointer dereference in bcm2835_thermal_debugfs. The driver makes use of the implementation details of the thermal framework to retrieve a pointer to its private data from a struct thermal_zone_device, and gets it wrong - leading to the crash. Instead, store its private data as the drvdata and retrieve the thermal_zone_device pointer from it. Fixes: bcb7dd9ef206 ("thermal: bcm2835: add thermal driver for bcm2835 SoC") Signed-off-by: Phil Elwell <phil@raspberrypi.org> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2019-03-18thermal: samsung: Fix incorrect check after code mergeMarek Szyprowski
Merge commit 19785cf93b6c ("Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal") broke the code introduced by commit ffe6e16f14fa ("thermal: exynos: Reduce severity of too early temperature read"). Restore the original code from the mentioned commit to finally fix the warning message during boot: thermal thermal_zone0: failed to read out thermal zone (-22) Reported-by: Marian Mihailescu <mihailescu2m@gmail.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 19785cf93b6c ("Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal") Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2019-03-18thermal/intel_powerclamp: fix __percpu declaration of worker_dataLuc Van Oostenryck
This variable is declared as: static struct powerclamp_worker_data * __percpu worker_data; In other words, a percpu pointer to struct ... But this variable not used like so but as a pointer to a percpu struct powerclamp_worker_data. So fix the declaration as: static struct powerclamp_worker_data __percpu *worker_data; This also quiets Sparse's warnings from __verify_pcpu_ptr(), like: 494:49: warning: incorrect type in initializer (different address spaces) 494:49: expected void const [noderef] <asn:3> *__vpp_verify 494:49: got struct powerclamp_worker_data * Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
2019-03-18paride/pcd: cleanup queues when detection failsJens Axboe
The driver allocates queues for all the units it potentially supports. But if we fail to detect any drives, then we fail loading the module without cleaning up those queues. This is now evident with the switch to blk-mq, though the bug has been there forever as far as I can tell. Also fix cleanup through regular module exit. Reported-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-03-18paride/pf: cleanup queues when detection failsJens Axboe
The driver allocates queues for all the units it potentially supports. But if we fail to detect any drives, then we fail loading the module without cleaning up those queues. This is now evident with the switch to blk-mq, though the bug has been there forever as far as I can tell. Also fix cleanup through regular module exit. Reported-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-03-19powerpc/6xx: fix setup and use of SPRN_SPRG_PGDIR for hash32Christophe Leroy
Not only the 603 but all 6xx need SPRN_SPRG_PGDIR to be initialised at startup. This patch move it from __setup_cpu_603() to start_here() and __secondary_start(), close to the initialisation of SPRN_THREAD. Previously, virt addr of PGDIR was retrieved from thread struct. Now that it is the phys addr which is stored in SPRN_SPRG_PGDIR, hash_page() shall not convert it to phys anymore. This patch removes the conversion. Fixes: 93c4a162b014 ("powerpc/6xx: Store PGDIR physical address in a SPRG") Reported-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2019-03-18drm/i915: Stop needlessly acquiring wakeref for debugfs/drop_caches_setChris Wilson
We only need to acquire a wakeref for ourselves for a few operations, as most either already acquire their own wakeref or imply a wakeref. In particular, it is i915_gem_set_wedged() that needed us to present it with a wakeref, which is incongruous with its "use anywhere" ability. Suggested-by: "Yokoyama, Caz" <caz.yokoyama@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: "Yokoyama, Caz" <caz.yokoyama@intel.com> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190318095204.9913-7-chris@chris-wilson.co.uk
2019-03-18drm/i915: Sanity check mmap length against object sizeChris Wilson
We assumed that vm_mmap() would reject an attempt to mmap past the end of the filp (our object), but we were wrong. Applications that tried to use the mmap beyond the end of the object would be greeted by a SIGBUS. After this patch, those applications will be told about the error on creating the mmap, rather than at a random moment on later access. Reported-by: Antonio Argenziano <antonio.argenziano@intel.com> Testcase: igt/gem_mmap/bad-size Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Antonio Argenziano <antonio.argenziano@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: stable@vger.kernel.org Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190314075829.16838-1-chris@chris-wilson.co.uk
2019-03-18ALSA: opl3: fix mismatch between snd_opl3_drum_switch definition and declarationColin Ian King
The function snd_opl3_drum_switch declaration in the header file has the order of the two arguments on_off and vel swapped when compared to the definition arguments of vel and on_off. Fix this by swapping them around to match the definition. This error predates the git history, so no idea when this error was introduced. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2019-03-18ALSA: hda - add Lenovo IdeaCentre B550 to the power_save_blacklistJaroslav Kysela
Another machine which does not like the power saving (noise): https://bugzilla.redhat.com/show_bug.cgi?id=1689623 Also, reorder the Lenovo C50 entry to keep the table sorted. Reported-by: hs.guimaraes@outlook.com Signed-off-by: Jaroslav Kysela <perex@perex.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2019-03-18iommu/amd: fix sg->dma_address for sg->offset bigger than PAGE_SIZEStanislaw Gruszka
Take into account that sg->offset can be bigger than PAGE_SIZE when setting segment sg->dma_address. Otherwise sg->dma_address will point at diffrent page, what makes DMA not possible with erros like this: xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa70c0 flags=0x0020] xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa7040 flags=0x0020] xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa7080 flags=0x0020] xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa7100 flags=0x0020] xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa7000 flags=0x0020] Additinally with wrong sg->dma_address unmap_sg will free wrong pages, what what can cause crashes like this: Feb 28 19:27:45 kernel: BUG: Bad page state in process cinnamon pfn:39e8b1 Feb 28 19:27:45 kernel: Disabling lock debugging due to kernel taint Feb 28 19:27:45 kernel: flags: 0x2ffff0000000000() Feb 28 19:27:45 kernel: raw: 02ffff0000000000 0000000000000000 ffffffff00000301 0000000000000000 Feb 28 19:27:45 kernel: raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000 Feb 28 19:27:45 kernel: page dumped because: nonzero _refcount Feb 28 19:27:45 kernel: Modules linked in: ccm fuse arc4 nct6775 hwmon_vid amdgpu nls_iso8859_1 nls_cp437 edac_mce_amd vfat fat kvm_amd ccp rng_core kvm mt76x0u mt76x0_common mt76x02_usb irqbypass mt76_usb mt76x02_lib mt76 crct10dif_pclmul crc32_pclmul chash mac80211 amd_iommu_v2 ghash_clmulni_intel gpu_sched i2c_algo_bit ttm wmi_bmof snd_hda_codec_realtek snd_hda_codec_generic drm_kms_helper snd_hda_codec_hdmi snd_hda_intel drm snd_hda_codec aesni_intel snd_hda_core snd_hwdep aes_x86_64 crypto_simd snd_pcm cfg80211 cryptd mousedev snd_timer glue_helper pcspkr r8169 input_leds realtek agpgart libphy rfkill snd syscopyarea sysfillrect sysimgblt fb_sys_fops soundcore sp5100_tco k10temp i2c_piix4 wmi evdev gpio_amdpt pinctrl_amd mac_hid pcc_cpufreq acpi_cpufreq sg ip_tables x_tables ext4(E) crc32c_generic(E) crc16(E) mbcache(E) jbd2(E) fscrypto(E) sd_mod(E) hid_generic(E) usbhid(E) hid(E) dm_mod(E) serio_raw(E) atkbd(E) libps2(E) crc32c_intel(E) ahci(E) libahci(E) libata(E) xhci_pci(E) xhci_hcd(E) Feb 28 19:27:45 kernel: scsi_mod(E) i8042(E) serio(E) bcache(E) crc64(E) Feb 28 19:27:45 kernel: CPU: 2 PID: 896 Comm: cinnamon Tainted: G B W E 4.20.12-arch1-1-custom #1 Feb 28 19:27:45 kernel: Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./B450M Pro4, BIOS P1.20 06/26/2018 Feb 28 19:27:45 kernel: Call Trace: Feb 28 19:27:45 kernel: dump_stack+0x5c/0x80 Feb 28 19:27:45 kernel: bad_page.cold.29+0x7f/0xb2 Feb 28 19:27:45 kernel: __free_pages_ok+0x2c0/0x2d0 Feb 28 19:27:45 kernel: skb_release_data+0x96/0x180 Feb 28 19:27:45 kernel: __kfree_skb+0xe/0x20 Feb 28 19:27:45 kernel: tcp_recvmsg+0x894/0xc60 Feb 28 19:27:45 kernel: ? reuse_swap_page+0x120/0x340 Feb 28 19:27:45 kernel: ? ptep_set_access_flags+0x23/0x30 Feb 28 19:27:45 kernel: inet_recvmsg+0x5b/0x100 Feb 28 19:27:45 kernel: __sys_recvfrom+0xc3/0x180 Feb 28 19:27:45 kernel: ? handle_mm_fault+0x10a/0x250 Feb 28 19:27:45 kernel: ? syscall_trace_enter+0x1d3/0x2d0 Feb 28 19:27:45 kernel: ? __audit_syscall_exit+0x22a/0x290 Feb 28 19:27:45 kernel: __x64_sys_recvfrom+0x24/0x30 Feb 28 19:27:45 kernel: do_syscall_64+0x5b/0x170 Feb 28 19:27:45 kernel: entry_SYSCALL_64_after_hwframe+0x44/0xa9 Cc: stable@vger.kernel.org Reported-and-tested-by: Jan Viktorin <jan.viktorin@gmail.com> Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Fixes: 80187fd39dcb ('iommu/amd: Optimize map_sg and unmap_sg') Signed-off-by: Joerg Roedel <jroedel@suse.de>
2019-03-18mmc: davinci: remove extraneous __init annotationArnd Bergmann
Building with clang finds a mistaken __init tag: WARNING: vmlinux.o(.text+0x5e4250): Section mismatch in reference from the function davinci_mmcsd_probe() to the function .init.text:init_mmcsd_host() The function davinci_mmcsd_probe() references the function __init init_mmcsd_host(). This is often because davinci_mmcsd_probe lacks a __init annotation or the annotation of init_mmcsd_host is wrong. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Wolfram Sang <wsa@the-dreams.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-03-18mmc: pxamci: fix enum type confusionArnd Bergmann
clang points out several instances of mismatched types in this drivers, all coming from a single declaration: drivers/mmc/host/pxamci.c:193:15: error: implicit conversion from enumeration type 'enum dma_transfer_direction' to different enumeration type 'enum dma_data_direction' [-Werror,-Wenum-conversion] direction = DMA_DEV_TO_MEM; ~ ^~~~~~~~~~~~~~ drivers/mmc/host/pxamci.c:212:62: error: implicit conversion from enumeration type 'enum dma_data_direction' to different enumeration type 'enum dma_transfer_direction' [-Werror,-Wenum-conversion] tx = dmaengine_prep_slave_sg(chan, data->sg, host->dma_len, direction, The behavior is correct, so this must be a simply typo from dma_data_direction and dma_transfer_direction being similarly named types with a similar purpose. Fixes: 6464b7140951 ("mmc: pxamci: switch over to dmaengine use") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-03-18dt-bindings: panel: td028ttec1: add backlight propertyAndreas Kemnade
This adds an additional backlight property as described in panel-common.txt Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: panel-tpo-td028ttec1: add backlight supportAndreas Kemnade
This panel has a backlight, so fetch it from devicetree using the corresponding property as documented in panel-common.txt. It is implemented the same way as in panel-dpi.c This ensures the backlight is also disabled when the display is turned off like when doing xset dpms force off. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: dsi: Fix PM for display blank with paired dss_pll callsTony Lindgren
Currently dsi_display_init_dsi() calls dss_pll_enable() but it is not paired with dss_pll_disable() in dsi_display_uninit_dsi(). This leaves the DSS clocks enabled when the display is blanked wasting about extra 5mW of power while idle. The clock that is left on by not calling dss_pll_disable() is DSS_CLKCTRL bit 10 OPTFCLKEN_SYS_CLK that is the source clock for DSI PLL. We can fix this issue by by making the current dsi_pll_uninit() into dsi_pll_disable(). This way we can just call dss_pll_disable() from dsi_display_uninit_dsi() and the code becomes a bit easier to follow. However, we need to also consider that DSI PLL can be muxed for DVI too as pointed out by Tomi Valkeinen <tomi.valkeinen@ti.com>. In the DVI case, we want to unconditionally disable the clocks. To get around this issue, we separate out the DSI lane handling from dsi_pll_enable() and dsi_pll_disable() as suggested by Tomi in an earlier experimental patch. So we must only toggle the DSI regulator based on the vdds_dsi_enabled flag from dsi_display_init_dsi() and dsi_display_uninit_dsi(). We need to make these two changes together to avoid breaking things for DVI when fixing the DSI clock handling. And this all causes a slight renumbering of the error path for dsi_display_init_dsi(). Suggested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm: Turn bus flags macros into an enumLaurent Pinchart
This allows nicer kerneldoc with an easy way to reference the enum and the values. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: Remove panel-dpi driverLaurent Pinchart
Panels are now supported through the drm_panel infrastructure, remove the omapdrm-specific driver. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: Remove TFP410 and DVI connector driversLaurent Pinchart
Those components are supported by the drm_bridge infrastructure, remove the omapdrm-specific driver. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: Whitelist DT nodes to fixup with omapdss, prefixLaurent Pinchart
The omapdss driver patches DT at runtime to prepend an "omapdss," prefix to the compatible string of all encoders, panels and connectors. This mechanism ensures they get bound to the omapdss-specific drivers instead of generic drivers. Now that we have drm_bridge support in omapdrm, we need to selectively disable this mechanism. Add a whitelist of compatible strings to patch, and fill it with all the devices we support. They will be removed one by one once corresponding drm_bridge drivers become available and get successfully tested with omapdrm. The omapdss components load check code is updated accordingly to ignore devices managed by external bridge drivers. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: Add support for drm_panelLaurent Pinchart
Hook up drm_panel support in the omapdrm driver. The change is relatively simply as the way has been paved by drm_bridge support already. In addition to looking up, attaching to and detaching from the panel, we only need to add panel support in the connector .get_modes() handler, take connector bus flags (set by the panel) into account, and enable/disable the panel in the encoder enable/disable operations handlers. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: Add support for drm_bridgeLaurent Pinchart
Hook up drm_bridge support in the omapdrm driver. Despite the recent extensive preparation work, this is a rather intrusive change, as the management of outputs needs to be adapted through the driver to handle both omap_dss_device and drm_bridge. Connector creation is skipped when using a drm_bridge, as the bridge creates the connector internally. This creates issues with systems that split connector operations (such as modes retrieval and hot-plug detection) across different bridges. These systems can't be supported using drm_bridge for now (their support through the omap_dss_device infrastructure is not affected), this will be fixed in subsequent changes. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/panel: simple: Add OSD070T1718-19TS panel supportLaurent Pinchart
Add support for the OSD070T1718-19TS 7" 800x480 panel from One Stop Displays to the panel-simple driver. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18dt-bindings: display: Add OSD Displays OSD070T1718-19TS panel bindingLaurent Pinchart
The OSD Displays OSD070T1718-19TS is a 7" WVGA (800x480) 24bit RGB panel and is compatible with the simple-panel bindings. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18dt-bindings: Add vendor prefix for OSD DisplaysLaurent Pinchart
OSD Displays is a panel manufacturer. It has been acquired by New Vision Displays in 2015 but continues to operate under its own brand name. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Rob Herring <robh@kernel.org> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/bridge: ti-tfp410: Report input bus config through bridge timingsLaurent Pinchart
The TFP410 supports configurable pixel clock sampling edge and data de-skew adjustments. The configuration can be set through I2C or dedicated chip pins. Report the configuration through the drm_bridge timings. As the ti-tftp410 driver doesn't support configuring the chip through I2C, we simply use the default configuration in that case. When the chip is configured through dedicated pins, we parse the configuration from DT. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Jyri Sarha <jsarha@ti.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/bridge: ti-tfp410: Add support for the powerdown GPIOLaurent Pinchart
The TFP410 has a powerdown pin that can be connected to a GPIO to control power saving. The DT bindings define a corresponding property, but the driver doesn't implement support for it. Fix that. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Jyri Sarha <jsarha@ti.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/bridge: ti-tfp410: Set connector type based on DT connector nodeLaurent Pinchart
The TI TFP410 is a DVI encoder, not a full HDMI encoder. Its output can be routed to a DVI-D connector, even if in many cases embedded systems will use an HDMI connector to carry the DVI signals. Instead of hardcoding the connector type to HDMI, retrieve the connector type from its DT node. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Jyri Sarha <jsarha@ti.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18dt-bindings: display: tfp410: Add bus parameters propertiesLaurent Pinchart
The TFP410 supports configuration of several input bus parameters through either the I2C port or chip pins. In the latter case, we need to specify those parameters in DT. Two new properties are added, ti,deskew to specify the data de-skew configuration (as set through the DK[3:1] pins), and pclk-sample to specify the pixel clock sampling edge (as set through the EDGE pin). Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Rob Herring <robh@kernel.org> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/bridge: use bus flags in bridge timingsStefan Agner
The DRM bus flags convey additional information on pixel data on the bus. All current available bus flags might be of interest for a bridge. Remove the sampling_edge field and use bus_flags. In the case at hand a dumb VGA bridge needs a specific data enable polarity (DRM_BUS_FLAG_DE_LOW). Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm: Use new DRM_BUS_FLAG_*_(DRIVE|SAMPLE)_(POS|NEG)EDGE flagsLaurent Pinchart
The DRM_BUS_FLAG_PIXDATA_(POS|NEG)EDGE and DRM_BUS_FLAG_SYNC_(POS|NEG)EDGE flags are deprecated in favour of the new DRM_BUS_FLAG_PIXDATA_(DRIVE|SAMPLE)_(POS|NEG)EDGE and new DRM_BUS_FLAG_SYNC_(DRIVE|SAMPLE)_(POS|NEG)EDGE flags. Replace them through the code. This effectively changes the value of the .sampling_edge bridge timings field in the dumb-vga-dac driver. This is safe to do as no driver consumes these values yet. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Stefan Agner <stefan@agner.ch> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm: Clarify definition of the DRM_BUS_FLAG_(PIXDATA|SYNC)_* macrosLaurent Pinchart
The DRM_BUS_FLAG_PIXDATA_POSEDGE and DRM_BUS_FLAG_PIXDATA_NEGEDGE macros and their DRM_BUS_FLAG_SYNC_* counterparts define on which pixel clock edge data and sync signals are driven. They are however used in some drivers to define on which pixel clock edge data and sync signals are sampled, which should usually (but not always) be the opposite edge of the driving edge. This creates confusion. Create four new macros for both PIXDATA and SYNC that explicitly state the driving and sampling edge in their name to remove the confusion. The driving macros are defined as the opposite of the sampling macros to made code simpler based on the assumption that the driving and sampling edges are opposite. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Stefan Agner <stefan@agner.ch> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: Merge omap_dss_device type and output_type fieldsLaurent Pinchart
The omap_dss_device type and output_type fields differ mostly for historical reasons. The output_type field is required for all devices but the display at the end of the pipeline, and must be set to OMAP_DISPLAY_TYPE_NONE for the latter. The type field is required for all devices but the internal encoder, for which it is ignored. The only reason why the output_type field must be set to OMAP_DISPLAY_TYPE_NONE for the display at the end of the pipeline is to identify omap_dss_device instances corresponding to displays. This is not documented and confusing. Clean the code by adding a new display field to the omap_dss_device structure to identify displays, and merge the type and output_type fields. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: Refactor initialization sequenceLaurent Pinchart
The omapdrm driver initialization procedure starts by connecting all available pipelines, gathering related information (such as output and display DSS devices, and DT aliases), sorting them by alias, and finally creates all the DRM/KMS objects. When using DRM bridges instead of DSS devices, we will need to attach to the bridges before getting the aliases. As attaching to bridges requires an encoder object, we have to reorganize the initialization sequence to create encoders before getting aliases and sorting the pipelines. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: Simplify OF lookup of DSS devicesLaurent Pinchart
Now that the direction of OF graph walk has been reversed, there's no need to lookup devices by port as we have no sink device connected through multiple sink ports. Simplify OF lookup of the DSS devices to look them up by node only. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: Store pixel clock instead of full mode in DPI and SDI encodersLaurent Pinchart
The DPI and SDI encoders store the full videomode upon mode set, to only use the value of the pixel clock when enabling the encoder. This wastes memory. Store the pixel clock value only. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: venc: Use drm_display_mode nativelyLaurent Pinchart
Replace internal usage of struct videomode with struct drm_display_mode in order to avoid converting needlessly between the data structures. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: Pass drm_display_mode to .check_timings() and .set_timings()Laurent Pinchart
The omap_dss_device .check_timings() and .set_timings() operations operate on struct videomode, while the DRM API operates on struct drm_display_mode. This forces conversion from to videomode in the callers. While that's not a problem per se, it creates a difference with the drm_bridge API. Replace the videomode parameter to the .check_timings() and .set_timings() operations with a drm_display_mode. This pushed the conversion to videomode down to the DSS devices in some cases. If needed they will be converted to operate on drm_display_mode natively. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: Factor out common mode validation codeLaurent Pinchart
The encoder .atomic_check() and connector .mode_valid() operations both walk through the dss devices in the pipeline to validate the mode. Factor out the common code in a new omap_drm_connector_mode_fixup() function. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: venc: Simplify mode setting by caching configurationLaurent Pinchart
The mode setting handler of the VENC stores the video mode internally, to then convert it to a configuration when programming the hardware. The stored mode is otherwise unused. Cache the configuration directly instead. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: Move DISPC timing checks to CRTC .mode_valid() operationLaurent Pinchart
The DISPC timings checks relate to the CRTC, but they're performed in the encoder and connector .atomic_check() and .mode_valid() operations. Move them to the CRTC .mode_valid() operation. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2019-03-18drm/omap: Remove src field from omap_dss_device structureLaurent Pinchart
The field is only used to check whether the device is connected, and we can do so by checking the dss field instead. Remove the src field. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
generated by cgit (git 2.34.1) at 2025-09-16 16:34:44 +0000