| Age | Commit message (Collapse) | Author |
|---|
|
The I²C mux controller is supplied by 3.3V rail. Add the corresponding
supply.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There are two SFP interfaces usable on TQMLS1046A. Enable all the
corresponding nodes. U-Boot will configure the connection if the RCW
is configured accordingly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is an SFP interface usable on TQMLS1043A. Enable all the
corresponding nodes. U-Boot will configure the connection if the RCW
is configured accordingly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
SFP is placed on mainboard, available to TQMLS1043A/1046A/1088A.
Provide it in a common place, disabled by default.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The jedec SPI-NOR flash node itself has no partitions, but the partitions
subnode.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The jedec SPI-NOR flash node itself has no partitions, but the partitions
subnode.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The jedec SPI-NOR flash node itself has no partitions, but the partitions
subnode.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing clocks and clock-names properties for flexcan1 in
imx94.dtsi to align with other FlexCAN instances.
Fixes: b0d011d4841b ("arm64: dts: freescale: Add basic dtsi for imx943")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
UART2 is often used as the console, so the DMA was likely left
off on purpose, since it's recommended to not use the DMA on the
console. Because, the driver checks to see if the UART is used for
the console when determining if it should initialize DMA, it
should be safe to enable DMA on UART2 for all users.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
UART2 is often used as the console, so the DMA was likely left
off on purpose, since it's recommended to not use the DMA on the
console. Because, the driver checks to see if the UART is used for
the console when determining if it should initialize DMA, it
should be safe to enable DMA on UART2 for all users.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Only i2c0 had it's DMA channels configured. Add the missing one.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Only i2c0 had it's DMA channels configured. Add the missing one.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On phyCORE-i.MX93 SoM, the SoC WDOG_ANY output line is connected to the
external pca9451a PMIC WDOG_B input. Apply pinctrl and set the property
"fsl,ext-reset-output" for watchdog to trigger board reset via PMIC on
timeout/reset.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The reference manual for the i.MX8MN states the clock rate in
MMC mode is 1/2 of the input clock, therefore to properly run
at HS400 rates, the input clock must be 400MHz to operate at
200MHz. Currently the clock is set to 200MHz which is half the
rate it should be, so the throughput is half of what it should be
for HS400 operation.
Fixes: 36ca3c8ccb53 ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The reference manual for the i.MX8MM states the clock rate in
MMC mode is 1/2 of the input clock, therefore to properly run
at HS400 rates, the input clock must be 400MHz to operate at
200MHz. Currently the clock is set to 200MHz which is half the
rate it should be, so the throughput is half of what it should be
for HS400 operation.
Fixes: 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This platform supports several displays, so rename the overlay to reflect
the actual display being used. This also aligns the name to the other
TQMa8M* modules. Apply the same change for MBa8MP-RAS314 as well, as it
uses the same overlay.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX8QM MEK RevD board is a reworked version of the i.MX8QM MEK
board, which includes some sensor and component changes. One of these
components is the WM8962 codec, which is meant to replace the WM8960
codec present on i.MX8QM MEK. To avoid having to introduce a devicetree
overlay or another DTS, the WM8962 can be supported by using a virtual
I2C MUX since both of the codecs share the same I2C address.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX8QXP WCPU MEK board is a reworked version of the i.MX8QXP MEK
board, which includes some sensor and component changes. One of these
components is the WM8962 codec, which is meant to replace the WM8960
codec present on i.MX8QXP MEK. To avoid having to introduce a devicetree
overlay or another DTS, the WM8962 can be supported by using a virtual
I2C MUX since both of the codecs share the same I2C address.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
In order to support Asynchronous Sample Rate Converter (ASRC), switch to
fsl-asoc-card driver for the wm8960 sound card.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add edma error irq for imx93.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Alberto Merciai <alb3rt0.m3rciai@gmail.com>
Tested-by: Alberto Merciai <alb3rt0.m3rciai@gmail.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The fan controller on this board cannot work in automatic mode, and
requires software control, the reason is that it has no temperature
sensor connected.
Given that this board is a development kit and does not have any
specific fan, add a default single cooling level that would enable the
fan to spin with a 100% duty cycle, enabling a safe default.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The defaults for this SoC are configured for overdrive mode, but
the VPU clocks are currently configured for nominal mode.
Increase VPU_G1_CLK_ROOT to 800MHZ from 600MHz,
Increase VPU_G2_CLK_ROOT to 700MHZ from 500MHz, and
Increase VPU_BUS_CLK_ROOT to 800MHz from 600MHz.
This requires adjusting the clock parents. Since there is already
800MHz clock references, move the VPU_BUS and G1 clocks to it.
This frees up the VPU_PLL to be configured at 700MHz to run
the G2 clock at 700MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
In preparation for increasing the default VPU clocks to overdrive,
configure the nominal values first to avoid running the nominal
devices out of spec when imx8mp.dtsi is changed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The VPU_PLL clock must be set before the VPU_BUS clock which is derived
from the VPU_PLL clock else the VPU_BUS clock is 300MHz and not 600MHz.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GPCv2 G1, G2 and VC8000E power-domain don't need to reference the
VPUMIX power-domain nor their module clocks since the power and reset
handling is done by the VPUMIX blkctrl driver.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
LGTM: Peng Fan <peng.fan@nxp.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon-kit
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The iMX8QXP and iMX8QM have a CAAM (Cryptographic Acceleration and
Assurance Module) like many other iMXs.
Add the definitions for it.
Job Rings 0 and 1 are bound to the SECO (Security Controller) ARM core
and are not exposed outside it. There's no point to define them in the
bindings as they cannot be used outside the SECO.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove the duplicated pinctrl_lpi2c3 node.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Reduce the driving strength of all Ethernet RGMII R/TXC pads according to
hardware signal measurement result.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The realtek phy CLKOUT signal is not used. Disable it to save power.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add usdhc3 and lpuart5 for imx93-9x9-qsb, imx93-11x11-evk and
imx93-14x14-evk, which connect to onboard wifi/bt module.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The "eee-broken-1000t" was added on 8mm for FEC to avoid issue of ptp sync.
EQoS haven't such issue. So, remove this for EQoS phys.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX93 9x9 qsb has a ST LSM6DSO connected to I2C, which a is 6-axis
IMU (inertial measurement unit = accelerometer & gyroscope). So add the
missing parts to the DTS file.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the EQoS Ethernet controller on the i.MX8MP VAR-SOM with the
integrated Maxlinear MXL86110 PHY. The PHY is connected to the EQOS
MDIO bus at address 4.
This patch adds:
- EQOS controller configuration with RGMII interface.
- Proper reset timings.
- PHY power supply regulators.
- RGMII pinmux configuration for all data, control and clock signals.
- LED configuration for link status indication via the LED subsystem
under /sys/class/leds/, leveraging the support implemented in the.
mxl86110 PHY driver (drivers/net/phy/mxl-86110.c).
Two LEDs are defined to match the LED configuration on the Variscite
VAR-SOM Carrier Boards:
* LED@0: Yellow, netdev trigger.
* LED@1: Green, netdev trigger.
The RGMII TX/RX delays are implemented in SOM via PCB passive
delays, so no software delay configuration is required.
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add system controller watchdog support for i.MX8QM.
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add GPIO reset for ethphy0.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The driver strength is too high for SDR104 mode. Change the driver strength
to x3 according to hardware recommendation.
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add USB3 PHY tuning properties for imx95-15x15-evk and imx95-19x19-evk
boards according to signal measurement results.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add adc0 flexcan[1,2] i2c[2,3] uart5 spi3 tpm3 netc_timer and related phys
regulators pinmux and related child nodes.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Variscite has updated the Ethernet PHY on the VAR-SOM-MX93 from the
ADIN1300BCPZ to the MaxLinear MXL86110, as documented in the
August 2023 revision changelog.
Link: https://variwiki.com/index.php?title=VAR-SOM-MX93_rev_changelog
Update the device tree accordingly:
- Drop the regulator node used to power the previously PHY.
- Add support for the reset line using GPIO1_IO07 with proper timings.
- Configure the PHY LEDs via the LED subsystem under /sys/class/leds/,
leveraging the support implemented in the mxl86110 PHY driver
(drivers/net/phy/mxl-86110.c).
Two LEDs are defined to match the LED configuration on the Variscite
VAR-SOM Carrier Boards:
* LED@0: Yellow, netdev trigger.
* LED@1: Green, netdev trigger.
- Adjust the RGMII clock pad control settings to match the updated PHY
requirements.
These changes ensure proper PHY initialization and LED status indication
for the new MaxLinear MXL86110, improving board compatibility with the
latest hardware revision.
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GW74xx D revision has added a M2SKT_WDIS2# GPIO which routes to the
W_DISABLE2# pin of the M.2 socket. Update the gpio name for consistency.
Fixes: 6a5d95b06d93 ("arm64: dts: imx8mp-venice-gw74xx: add M2SKT_GPIO10 gpio configuration")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Although the bootloader should fixup with real memory size,
add memory node here with smallest assembled size for
readability.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move configuration for ADC voltage reference from board DTS to a SoM
include file. The SoC ADC reference voltage is connected to a "VDDA_1V8"
voltage node and supplied by the PMIC's BUCK5 regulator. The reference
voltage is thus defined by the SoM and cannot be changed by the carrier
board design and as such belongs into the SoM include file.
Moreover, with this in place, customers designing own carrier boards can
simply include imx93-phycore-som.dtsi and enable adc1 in their own DTS
without the need to define dummy ADC vref regulator themselves anymore.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX95 NETC supports SMMU, so add SMMU support.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PDM micphone sound card support, configure the pinmux.
This sound card supports recording sound from PDM microphone and convert
the PDM format data to PCM data.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add bt-sco sound card, which is used by BT HFP case.
It supports wb profile as default.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add WM8962 codec connected to SAI1 interface.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add i2c io expander support for imx943 evk board.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add lpi2c and i2c-mux support for imx943 evk board.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add micfil and mqs device nodes
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The RTC module on S32G2/S32G3 based SoCs is used as a wakeup source from
system suspend.
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
