| Age | Commit message (Collapse) | Author |
|---|
|
Coverity also complains about the way we calculate the offset
(starting from the address of a 4 byte array within the
header structure rather than from the beginning of the struct
plus 4 bytes) for SMB1 CIFSPOSIXDelFile. This changeset
doesn't change the address but makes it slightly clearer.
Addresses-Coverity: 711519 ("Out of bounds write")
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.14-rc3
Here are some new device ids and a device-id comment fix.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.14-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
USB: serial: cp210x: fix comments for GE CS1000
USB: serial: option: add support for u-blox LARA-R6 family
|
|
Coverity also complains about the way we calculate the offset
(starting from the address of a 4 byte array within the
header structure rather than from the beginning of the struct
plus 4 bytes) for SMB1 CIFSPOSIXCreate. This changeset
doesn't change the address but makes it slightly clearer.
Addresses-Coverity: 711518 ("Out of bounds write")
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A pair of arm64 fixes for -rc3. The straightforward one is a fix to
our firmware calling stub, which accidentally started corrupting the
link register on machines with SVE. Since these machines don't really
exist yet, it wasn't spotted in -next.
The other fix is a revert-and-a-bit of a patch originally intended to
allow PTE-level huge mappings for the VMAP area on 32-bit PPC 8xx. A
side-effect of this change was that our pXd_set_huge() implementations
could be replaced with generic dummy functions depending on the levels
of page-table being used, which in turn broke the boot if we fail to
create the linear mapping as a result of using these functions to
operate on the pgd. Huge thanks to Michael Ellerman for modifying the
revert so as not to regress PPC 8xx in terms of functionality.
Anyway, that's the background and it's also available in the commit
message along with Link tags pointing at all of the fun.
Summary:
- Fix hang when issuing SMC on SVE-capable system due to
clobbered LR
- Fix boot failure due to missing block mappings with folded
page-table"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Revert "mm/pgtable: add stubs for {pmd/pub}_{set/clear}_huge"
arm64: smccc: Save lr before calling __arm_smccc_sve_check()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- bug fix from Haiyang for vmbus CPU assignment
- revert of a bogus patch that went into 5.14-rc1
* tag 'hyperv-fixes-signed-20210722' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
Revert "x86/hyperv: fix logical processor creation"
Drivers: hv: vmbus: Fix duplicate CPU assignments within a device
|
|
Pull networking fixes from David Miller:
1) Fix type of bind option flag in af_xdp, from Baruch Siach.
2) Fix use after free in bpf_xdp_link_release(), from Xuan Zhao.
3) PM refcnt imbakance in r8152, from Takashi Iwai.
4) Sign extension ug in liquidio, from Colin Ian King.
5) Mising range check in s390 bpf jit, from Colin Ian King.
6) Uninit value in caif_seqpkt_sendmsg(), from Ziyong Xuan.
7) Fix skb page recycling race, from Ilias Apalodimas.
8) Fix memory leak in tcindex_partial_destroy_work, from Pave Skripkin.
9) netrom timer sk refcnt issues, from Nguyen Dinh Phi.
10) Fix data races aroun tcp's tfo_active_disable_stamp, from Eric
Dumazet.
11) act_skbmod should only operate on ethernet packets, from Peilin Ye.
12) Fix slab out-of-bpunds in fib6_nh_flush_exceptions(),, from Psolo
Abeni.
13) Fix sparx5 dependencies, from Yajun Deng.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (74 commits)
dpaa2-switch: seed the buffer pool after allocating the swp
net: sched: cls_api: Fix the the wrong parameter
net: sparx5: fix unmet dependencies warning
net: dsa: tag_ksz: dont let the hardware process the layer 4 checksum
net: dsa: ensure linearized SKBs in case of tail taggers
ravb: Remove extra TAB
ravb: Fix a typo in comment
net: dsa: sja1105: make VID 4095 a bridge VLAN too
tcp: disable TFO blackhole logic by default
sctp: do not update transport pathmtu if SPP_PMTUD_ENABLE is not set
net: ixp46x: fix ptp build failure
ibmvnic: Remove the proper scrq flush
selftests: net: add ESP-in-UDP PMTU test
udp: check encap socket in __udp_lib_err
sctp: update active_key for asoc when old key is being replaced
r8169: Avoid duplicate sysfs entry creation error
ixgbe: Fix packet corruption due to missing DMA sync
Revert "qed: fix possible unpaired spin_{un}lock_bh in _qed_mcp_cmd_and_union()"
ipv6: fix another slab-out-of-bounds in fib6_nh_flush_exceptions
fsl/fman: Add fibre support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- Use kref to fix KASAN splats triggered during card removal
- Don't allocate IDA for OF aliases
* tag 'mmc-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: Don't allocate IDA for OF aliases
mmc: core: Use kref in place of struct mmc_blk_data::usage
|
|
When remouting a DFS share, force a new DFS referral of the path and
if the currently cached targets do not match any of the new targets or
there was no cached targets, then mark it for reconnect.
For example:
$ mount //dom/dfs/link /mnt -o username=foo,password=bar
$ ls /mnt
oldfile.txt
change target share of 'link' in server settings
$ mount /mnt -o remount,username=foo,password=bar
$ ls /mnt
newfile.txt
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
We only allow sending single credit writes through the SMB2_write() synchronous
api so split this into smaller chunks.
Fixes: 966a3cb7c7db ("cifs: improve fallocate emulation")
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reported-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
The "rb_per_cpu_empty()" misinterpret the condition (as not-empty) when
"head_page" and "commit_page" of "struct ring_buffer_per_cpu" points to
the same buffer page, whose "buffer_data_page" is empty and "read" field
is non-zero.
An error scenario could be constructed as followed (kernel perspective):
1. All pages in the buffer has been accessed by reader(s) so that all of
them will have non-zero "read" field.
2. Read and clear all buffer pages so that "rb_num_of_entries()" will
return 0 rendering there's no more data to read. It is also required
that the "read_page", "commit_page" and "tail_page" points to the same
page, while "head_page" is the next page of them.
3. Invoke "ring_buffer_lock_reserve()" with large enough "length"
so that it shot pass the end of current tail buffer page. Now the
"head_page", "commit_page" and "tail_page" points to the same page.
4. Discard current event with "ring_buffer_discard_commit()", so that
"head_page", "commit_page" and "tail_page" points to a page whose buffer
data page is now empty.
When the error scenario has been constructed, "tracing_read_pipe" will
be trapped inside a deadloop: "trace_empty()" returns 0 since
"rb_per_cpu_empty()" returns 0 when it hits the CPU containing such
constructed ring buffer. Then "trace_find_next_entry_inc()" always
return NULL since "rb_num_of_entries()" reports there's no more entry
to read. Finally "trace_seq_to_user()" returns "-EBUSY" spanking
"tracing_read_pipe" back to the start of the "waitagain" loop.
I've also written a proof-of-concept script to construct the scenario
and trigger the bug automatically, you can use it to trace and validate
my reasoning above:
https://github.com/aegistudio/RingBufferDetonator.git
Tests has been carried out on linux kernel 5.14-rc2
(2734d6c1b1a089fb593ef6a23d4b70903526fe0c), my fixed version
of kernel (for testing whether my update fixes the bug) and
some older kernels (for range of affected kernels). Test result is
also attached to the proof-of-concept repository.
Link: https://lore.kernel.org/linux-trace-devel/YPaNxsIlb2yjSi5Y@aegistudio/
Link: https://lore.kernel.org/linux-trace-devel/YPgrN85WL9VyrZ55@aegistudio
Cc: stable@vger.kernel.org
Fixes: bf41a158cacba ("ring-buffer: make reentrant")
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Haoran Luo <www@aegistudio.net>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Store the block device instead of the gendisk in the btrfs_ordered_extent
structure instead of acquiring a reference to it later.
Note: this is from series removing bdgrab/bdput, btrfs is one of the
last users.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
At btrfs_qgroup_trace_extent_post() we call btrfs_find_all_roots() with a
NULL value as the transaction handle argument, which makes that function
take the commit_root_sem semaphore, which is necessary when we don't hold
a transaction handle or any other mechanism to prevent a transaction
commit from wiping out commit roots.
However btrfs_qgroup_trace_extent_post() can be called in a context where
we are holding a write lock on an extent buffer from a subvolume tree,
namely from btrfs_truncate_inode_items(), called either during truncate
or unlink operations. In this case we end up with a lock inversion problem
because the commit_root_sem is a higher level lock, always supposed to be
acquired before locking any extent buffer.
Lockdep detects this lock inversion problem since we switched the extent
buffer locks from custom locks to semaphores, and when running btrfs/158
from fstests, it reported the following trace:
[ 9057.626435] ======================================================
[ 9057.627541] WARNING: possible circular locking dependency detected
[ 9057.628334] 5.14.0-rc2-btrfs-next-93 #1 Not tainted
[ 9057.628961] ------------------------------------------------------
[ 9057.629867] kworker/u16:4/30781 is trying to acquire lock:
[ 9057.630824] ffff8e2590f58760 (btrfs-tree-00){++++}-{3:3}, at: __btrfs_tree_read_lock+0x24/0x110 [btrfs]
[ 9057.632542]
but task is already holding lock:
[ 9057.633551] ffff8e25582d4b70 (&fs_info->commit_root_sem){++++}-{3:3}, at: iterate_extent_inodes+0x10b/0x280 [btrfs]
[ 9057.635255]
which lock already depends on the new lock.
[ 9057.636292]
the existing dependency chain (in reverse order) is:
[ 9057.637240]
-> #1 (&fs_info->commit_root_sem){++++}-{3:3}:
[ 9057.638138] down_read+0x46/0x140
[ 9057.638648] btrfs_find_all_roots+0x41/0x80 [btrfs]
[ 9057.639398] btrfs_qgroup_trace_extent_post+0x37/0x70 [btrfs]
[ 9057.640283] btrfs_add_delayed_data_ref+0x418/0x490 [btrfs]
[ 9057.641114] btrfs_free_extent+0x35/0xb0 [btrfs]
[ 9057.641819] btrfs_truncate_inode_items+0x424/0xf70 [btrfs]
[ 9057.642643] btrfs_evict_inode+0x454/0x4f0 [btrfs]
[ 9057.643418] evict+0xcf/0x1d0
[ 9057.643895] do_unlinkat+0x1e9/0x300
[ 9057.644525] do_syscall_64+0x3b/0xc0
[ 9057.645110] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 9057.645835]
-> #0 (btrfs-tree-00){++++}-{3:3}:
[ 9057.646600] __lock_acquire+0x130e/0x2210
[ 9057.647248] lock_acquire+0xd7/0x310
[ 9057.647773] down_read_nested+0x4b/0x140
[ 9057.648350] __btrfs_tree_read_lock+0x24/0x110 [btrfs]
[ 9057.649175] btrfs_read_lock_root_node+0x31/0x40 [btrfs]
[ 9057.650010] btrfs_search_slot+0x537/0xc00 [btrfs]
[ 9057.650849] scrub_print_warning_inode+0x89/0x370 [btrfs]
[ 9057.651733] iterate_extent_inodes+0x1e3/0x280 [btrfs]
[ 9057.652501] scrub_print_warning+0x15d/0x2f0 [btrfs]
[ 9057.653264] scrub_handle_errored_block.isra.0+0x135f/0x1640 [btrfs]
[ 9057.654295] scrub_bio_end_io_worker+0x101/0x2e0 [btrfs]
[ 9057.655111] btrfs_work_helper+0xf8/0x400 [btrfs]
[ 9057.655831] process_one_work+0x247/0x5a0
[ 9057.656425] worker_thread+0x55/0x3c0
[ 9057.656993] kthread+0x155/0x180
[ 9057.657494] ret_from_fork+0x22/0x30
[ 9057.658030]
other info that might help us debug this:
[ 9057.659064] Possible unsafe locking scenario:
[ 9057.659824] CPU0 CPU1
[ 9057.660402] ---- ----
[ 9057.660988] lock(&fs_info->commit_root_sem);
[ 9057.661581] lock(btrfs-tree-00);
[ 9057.662348] lock(&fs_info->commit_root_sem);
[ 9057.663254] lock(btrfs-tree-00);
[ 9057.663690]
*** DEADLOCK ***
[ 9057.664437] 4 locks held by kworker/u16:4/30781:
[ 9057.665023] #0: ffff8e25922a1148 ((wq_completion)btrfs-scrub){+.+.}-{0:0}, at: process_one_work+0x1c7/0x5a0
[ 9057.666260] #1: ffffabb3451ffe70 ((work_completion)(&work->normal_work)){+.+.}-{0:0}, at: process_one_work+0x1c7/0x5a0
[ 9057.667639] #2: ffff8e25922da198 (&ret->mutex){+.+.}-{3:3}, at: scrub_handle_errored_block.isra.0+0x5d2/0x1640 [btrfs]
[ 9057.669017] #3: ffff8e25582d4b70 (&fs_info->commit_root_sem){++++}-{3:3}, at: iterate_extent_inodes+0x10b/0x280 [btrfs]
[ 9057.670408]
stack backtrace:
[ 9057.670976] CPU: 7 PID: 30781 Comm: kworker/u16:4 Not tainted 5.14.0-rc2-btrfs-next-93 #1
[ 9057.672030] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[ 9057.673492] Workqueue: btrfs-scrub btrfs_work_helper [btrfs]
[ 9057.674258] Call Trace:
[ 9057.674588] dump_stack_lvl+0x57/0x72
[ 9057.675083] check_noncircular+0xf3/0x110
[ 9057.675611] __lock_acquire+0x130e/0x2210
[ 9057.676132] lock_acquire+0xd7/0x310
[ 9057.676605] ? __btrfs_tree_read_lock+0x24/0x110 [btrfs]
[ 9057.677313] ? lock_is_held_type+0xe8/0x140
[ 9057.677849] down_read_nested+0x4b/0x140
[ 9057.678349] ? __btrfs_tree_read_lock+0x24/0x110 [btrfs]
[ 9057.679068] __btrfs_tree_read_lock+0x24/0x110 [btrfs]
[ 9057.679760] btrfs_read_lock_root_node+0x31/0x40 [btrfs]
[ 9057.680458] btrfs_search_slot+0x537/0xc00 [btrfs]
[ 9057.681083] ? _raw_spin_unlock+0x29/0x40
[ 9057.681594] ? btrfs_find_all_roots_safe+0x11f/0x140 [btrfs]
[ 9057.682336] scrub_print_warning_inode+0x89/0x370 [btrfs]
[ 9057.683058] ? btrfs_find_all_roots_safe+0x11f/0x140 [btrfs]
[ 9057.683834] ? scrub_write_block_to_dev_replace+0xb0/0xb0 [btrfs]
[ 9057.684632] iterate_extent_inodes+0x1e3/0x280 [btrfs]
[ 9057.685316] scrub_print_warning+0x15d/0x2f0 [btrfs]
[ 9057.685977] ? ___ratelimit+0xa4/0x110
[ 9057.686460] scrub_handle_errored_block.isra.0+0x135f/0x1640 [btrfs]
[ 9057.687316] scrub_bio_end_io_worker+0x101/0x2e0 [btrfs]
[ 9057.688021] btrfs_work_helper+0xf8/0x400 [btrfs]
[ 9057.688649] ? lock_is_held_type+0xe8/0x140
[ 9057.689180] process_one_work+0x247/0x5a0
[ 9057.689696] worker_thread+0x55/0x3c0
[ 9057.690175] ? process_one_work+0x5a0/0x5a0
[ 9057.690731] kthread+0x155/0x180
[ 9057.691158] ? set_kthread_struct+0x40/0x40
[ 9057.691697] ret_from_fork+0x22/0x30
Fix this by making btrfs_find_all_roots() never attempt to lock the
commit_root_sem when it is called from btrfs_qgroup_trace_extent_post().
We can't just pass a non-NULL transaction handle to btrfs_find_all_roots()
from btrfs_qgroup_trace_extent_post(), because that would make backref
lookup not use commit roots and acquire read locks on extent buffers, and
therefore could deadlock when btrfs_qgroup_trace_extent_post() is called
from the btrfs_truncate_inode_items() code path which has acquired a write
lock on an extent buffer of the subvolume btree.
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
A fstrim on a degraded raid1 can trigger the following null pointer
dereference:
BTRFS info (device loop0): allowing degraded mounts
BTRFS info (device loop0): disk space caching is enabled
BTRFS info (device loop0): has skinny extents
BTRFS warning (device loop0): devid 2 uuid 97ac16f7-e14d-4db1-95bc-3d489b424adb is missing
BTRFS warning (device loop0): devid 2 uuid 97ac16f7-e14d-4db1-95bc-3d489b424adb is missing
BTRFS info (device loop0): enabling ssd optimizations
BUG: kernel NULL pointer dereference, address: 0000000000000620
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 0 PID: 4574 Comm: fstrim Not tainted 5.13.0-rc7+ #31
Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
RIP: 0010:btrfs_trim_fs+0x199/0x4a0 [btrfs]
RSP: 0018:ffff959541797d28 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff946f84eca508 RCX: a7a67937adff8608
RDX: ffff946e8122d000 RSI: 0000000000000000 RDI: ffffffffc02fdbf0
RBP: ffff946ea4615000 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: ffff946e8122d960 R12: 0000000000000000
R13: ffff959541797db8 R14: ffff946e8122d000 R15: ffff959541797db8
FS: 00007f55917a5080(0000) GS:ffff946f9bc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000620 CR3: 000000002d2c8001 CR4: 00000000000706f0
Call Trace:
btrfs_ioctl_fitrim+0x167/0x260 [btrfs]
btrfs_ioctl+0x1c00/0x2fe0 [btrfs]
? selinux_file_ioctl+0x140/0x240
? syscall_trace_enter.constprop.0+0x188/0x240
? __x64_sys_ioctl+0x83/0xb0
__x64_sys_ioctl+0x83/0xb0
Reproducer:
$ mkfs.btrfs -fq -d raid1 -m raid1 /dev/loop0 /dev/loop1
$ mount /dev/loop0 /btrfs
$ umount /btrfs
$ btrfs dev scan --forget
$ mount -o degraded /dev/loop0 /btrfs
$ fstrim /btrfs
The reason is we call btrfs_trim_free_extents() for the missing device,
which uses device->bdev (NULL for missing device) to find if the device
supports discard.
Fix is to check if the device is missing before calling
btrfs_trim_free_extents().
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
If we have an inode that does not have the full sync flag set, was changed
in the current transaction, then it is logged while logging some other
inode (like its parent directory for example), its i_size is increased by
a truncate operation, the log is synced through an fsync of some other
inode and then finally we explicitly call fsync on our inode, the new
i_size is not persisted.
The following example shows how to trigger it, with comments explaining
how and why the issue happens:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ touch /mnt/foo
$ xfs_io -f -c "pwrite -S 0xab 0 1M" /mnt/bar
$ sync
# Fsync bar, this will be a noop since the file has not yet been
# modified in the current transaction. The goal here is to clear
# BTRFS_INODE_NEEDS_FULL_SYNC from the inode's runtime flags.
$ xfs_io -c "fsync" /mnt/bar
# Now rename both files, without changing their parent directory.
$ mv /mnt/bar /mnt/bar2
$ mv /mnt/foo /mnt/foo2
# Increase the size of bar2 with a truncate operation.
$ xfs_io -c "truncate 2M" /mnt/bar2
# Now fsync foo2, this results in logging its parent inode (the root
# directory), and logging the parent results in logging the inode of
# file bar2 (its inode item and the new name). The inode of file bar2
# is logged with an i_size of 0 bytes since it's logged in
# LOG_INODE_EXISTS mode, meaning we are only logging its names (and
# xattrs if it had any) and the i_size of the inode will not be changed
# when the log is replayed.
$ xfs_io -c "fsync" /mnt/foo2
# Now explicitly fsync bar2. This resulted in doing nothing, not
# logging the inode with the new i_size of 2M and the hole from file
# offset 1M to 2M. Because the inode did not have the flag
# BTRFS_INODE_NEEDS_FULL_SYNC set, when it was logged through the
# fsync of file foo2, its last_log_commit field was updated,
# resulting in this explicit of file bar2 not doing anything.
$ xfs_io -c "fsync" /mnt/bar2
# File bar2 content and size before a power failure.
$ od -A d -t x1 /mnt/bar2
0000000 ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab
*
1048576 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
2097152
<power failure>
# Mount the filesystem to replay the log.
$ mount /dev/sdc /mnt
# Read the file again, should have the same content and size as before
# the power failure happened, but it doesn't, i_size is still at 1M.
$ od -A d -t x1 /mnt/bar2
0000000 ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab
*
1048576
This started to happen after commit 209ecbb8585bf6 ("btrfs: remove stale
comment and logic from btrfs_inode_in_log()"), since btrfs_inode_in_log()
no longer checks if the inode's list of modified extents is not empty.
However, checking that list is not the right way to address this case
and the check was added long time ago in commit 125c4cf9f37c98
("Btrfs: set inode's logged_trans/last_log_commit after ranged fsync")
for a different purpose, to address consecutive ranged fsyncs.
The reason that checking for the list emptiness makes this test pass is
because during an expanding truncate we create an extent map to represent
a hole from the old i_size to the new i_size, and add that extent map to
the list of modified extents in the inode. However if we are low on
available memory and we can not allocate a new extent map, then we don't
treat it as an error and just set the full sync flag on the inode, so that
the next fsync does not rely on the list of modified extents - so checking
for the emptiness of the list to decide if the inode needs to be logged is
not reliable, and results in not logging the inode if it was not possible
to allocate the extent map for the hole.
Fix this by ensuring that if we are only logging that an inode exists
(inode item, names/references and xattrs), we don't update the inode's
last_log_commit even if it does not have the full sync runtime flag set.
A test case for fstests follows soon.
CC: stable@vger.kernel.org # 5.13+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Any interraction with the buffer pool (seeding a buffer, acquire one) is
made through a software portal (SWP, a DPIO object).
There are circumstances where the dpaa2-switch driver probes on a DPSW
before any DPIO devices have been probed. In this case, seeding of the
buffer pool will lead to a panic since no SWPs are initialized.
To fix this, seed the buffer pool after making sure that the software
portals have been probed and are ready to be used.
Fixes: 0b1b71370458 ("staging: dpaa2-switch: handle Rx path on control interface")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The return type of the function is bool and while NULL do evaluate to
false it's not very nice, fix this by explicitly returning false. There
is no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We create a bunch of debugfs entries as a side-effect of
ttm_global_init() and then never clean them up. This isn't usually a
problem because we free the whole debugfs directory on module unload.
However, if the global reference count ever goes to zero and then
ttm_global_init() is called again, we'll re-create those debugfs entries
and debugfs will complain in dmesg that we're creating entries that
already exist. This patch fixes this problem by changing the lifetime
of the whole TTM debugfs directory to match that of the TTM global
state.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721152358.2893314-6-jason@jlekstrand.net
|
|
The mipi_dsi_device allocated by mipi_dsi_device_register_full() is
already free'd on release.
Fixes: 2f733d6194bd ("drm/panel: Add support for the Raspberry Pi 7" Touchscreen.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720134525.563936-9-maxime@cerno.tech
|
|
When compiling without CONFIG_SYSCTL, this warning appears:
net/ipv6/addrconf.c:99:12: error: 'ioam6_if_id_max' defined but not used [-Werror=unused-variable]
99 | static u32 ioam6_if_id_max = U16_MAX;
| ^~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Simply moving the declaration of this variable under ...
#ifdef CONFIG_SYSCTL
... with other similar variables fixes the issue.
Fixes: 9ee11f0fff20 ("ipv6: ioam: Data plane support for Pre-allocated Trace")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon Horman says:
====================
nfp: flower: conntrack offload
Louis Peens says:
This series takes the preparation from previous two series
and finally creates the structures and control messages
to offload the conntrack flows to the card. First we
do a bit of refactoring in the existing functions
to make them re-usable for the conntrack implementation,
after which the control messages are compiled and
transmitted to the card. Lastly we add stats handling
for the conntrack flows.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add in the logic to update flow stats. The flow stats from the nfp
is saved in the flow_pay struct, which is associated with the final
merged flow. This saves deltas however, so once read it needs to
be cleared. However the flow stats requests from the kernel is
from the other side of the chain, and a single tc flow from
the kernel can be merged into multiple other tc flows to form
multiple offloaded flows. This means that all linked flows
needs to be updated for each stats request.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the offload parts (ADD_FLOW/DEL_FLOW) calls to add and delete
the flows from the nfp.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Compile the offload flow metadata and add flow_pay to the offload
table. Also add in the delete paths. This does not include actual
offloading to the card yet, this will follow soon.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Combine the actions from the three different rules into one and
convert into the payload format expected by the nfp.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add in the code to compile match part of the payload that will be
sent to the firmware. This works similar to match.c does it, but
since three flows needs to be merged it iterates through all three
rules in a loop and combine the match fields to get the most strict
match as result.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This calculates the correct combined keylayers and key_layer_size
for the to-be-offloaded flow.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the action related offload functions to take in flow_rule *
as input instead of flow_cls_offload * as input. The flow_rule
parts of flow_cls_offload is the only part that is used in any
case, and this is required for more conntrack offload patches
which will follow later.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a small cleanup to pass in flow->rule to some of the compile
functions instead of extracting it every time. This is will also be
useful for conntrack patches later.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Expose and refactor the match compilation functions so that they
can be invoked externally. Also update the functions so they can
be called multiple times with the results OR'd together. This is
applicable for the flows-merging scenario, in which there could be
overlapped and non-conflicting match fields. This will be used
in upcoming conntrack patches. This is safe to do in the in the
single call case as well since both unmasked_data and mask_data
gets initialised to 0.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test if we actually can send/receive packets with MTU size. This kind of
issue was detected on ASIX HW with bogus EEPROM.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing stop and let phylib framework suspend attached PHY.
Fixes: e532a096be0e ("net: usb: asix: ax88772: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
asix_get_phyid() is used for two reasons here. To print debug message
with the PHY ID and to wait until the PHY is powered up.
After migrating to the phylib, we can read PHYID from sysfs. If polling
for the PHY is really needed, then we will need to handle it in the
phylib as well.
This change was tested with:
- ax88772a + internal PHY
- ax88772b + external PHY
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 4th parameter in tc_chain_notify() should be flags rather than seq.
Let's change it back correctly.
Fixes: 32a4f5ecd738 ("net: sched: introduce chain object to uapi")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
to us
The newly introduced switchdev_handle_fdb_{add,del}_to_device helpers
solved a problem but introduced another one. They have a severe design
bug: they do not propagate FDB events on foreign interfaces to us, i.e.
this use case:
br0
/ \
/ \
/ \
/ \
swp0 eno0
(switchdev) (foreign)
when an address is learned on eno0, what is supposed to happen is that
this event should also be propagated towards swp0. Somehow I managed to
convince myself that this did work correctly, but obviously it does not.
The trouble with foreign interfaces is that we must reach a switchdev
net_device pointer through a foreign net_device that has no direct
upper/lower relationship with it. So we need to do exploratory searching
through the lower interfaces of the foreign net_device's bridge upper
(to reach swp0 from eno0, we must check its upper, br0, for lower
interfaces that pass the check_cb and foreign_dev_check_cb). This is
something that the previous code did not do, it just assumed that "dev"
will become a switchdev interface at some point, somehow, probably by
magic.
With this patch, assisted address learning on the CPU port works again
in DSA:
ip link add br0 type bridge
ip link set swp0 master br0
ip link set eno0 master br0
ip link set br0 up
[ 46.708929] mscc_felix 0000:00:00.5 swp0: Adding FDB entry towards eno0, addr 00:04:9f:05:f4:ab vid 0 as host address
Fixes: 8ca07176ab00 ("net: switchdev: introduce a fanout helper for SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE")
Reported-by: Eric Woudstra <ericwouds@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WARNING: unmet direct dependencies detected for PHY_SPARX5_SERDES
Depends on [n]: (ARCH_SPARX5 || COMPILE_TEST [=n]) && OF [=y] && HAS_IOMEM [=y]
Selected by [y]:
- SPARX5_SWITCH [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICROCHIP [=y] && NET_SWITCHDEV [=y] && HAS_IOMEM [=y] && OF [=y]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These devices has two interfaces, but only the second interface
contains the capture endpoint, thus quirk is required to delay the
registration until the second interface appears.
Tested-by: Jakub Fišer <jakub@ufiseru.cz>
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210721235605.53741-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Vladimir Oltean says:
====================
Let switchdev drivers offload and unoffload bridge ports at their own convenience
This series introduces an explicit API through which switchdev drivers
mark a bridge port as offloaded or not:
- switchdev_bridge_port_offload()
- switchdev_bridge_port_unoffload()
Currently, the bridge assumes that a port is offloaded if
dev_get_port_parent_id(dev, &ppid, recurse=true) returns something, but
that is just an assumption that breaks some use cases (like a
non-offloaded LAG interface on top of a switchdev port, bridged with
other switchdev ports).
Along with some consolidation of the bridge logic to assign a "switchdev
offloading mark" to a port (now better called a "hardware domain"), this
series allows the bridge driver side to no longer impose restrictions on
that configuration.
Right now, all switchdev drivers must be modified to use the explicit
API, but more and more logic can then be placed centrally in the bridge
and therefore ease the job of a switchdev driver writer in the future.
For example, the first thing we can hook into the explicit switchdev
offloading API calls are the switchdev object and FDB replay helpers.
So far, these have only been used by DSA in "pull" mode (where the
driver must ask for them). Adding the replay helpers to other drivers
involves a lot of repetition. But by moving the helpers inside the
bridge port offload/unoffload hook points, we can move the entire replay
process to "push" mode (where the bridge provides them automatically).
The explicit switchdev offloading API will see further extensions in the
future.
The patches were split from a larger series for easier review:
https://patchwork.kernel.org/project/netdevbpf/cover/20210718214434.3938850-1-vladimir.oltean@nxp.com/
Changes in v6:
- Make the switchdev replay helpers opt-in
- Opt out of the replay helpers for mlxsw, rocker, prestera, sparx5,
cpsw, am65-cpsw
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Starting with commit 4f2673b3a2b6 ("net: bridge: add helper to replay
port and host-joined mdb entries"), DSA has introduced some bridge
helpers that replay switchdev events (FDB/MDB/VLAN additions and
deletions) that can be lost by the switchdev drivers in a variety of
circumstances:
- an IP multicast group was host-joined on the bridge itself before any
switchdev port joined the bridge, leading to the host MDB entries
missing in the hardware database.
- during the bridge creation process, the MAC address of the bridge was
added to the FDB as an entry pointing towards the bridge device
itself, but with no switchdev ports being part of the bridge yet, this
local FDB entry would remain unknown to the switchdev hardware
database.
- a VLAN/FDB/MDB was added to a bridge port that is a LAG interface,
before any switchdev port joined that LAG, leading to the hardware
database missing those entries.
- a switchdev port left a LAG that is a bridge port, while the LAG
remained part of the bridge, and all FDB/MDB/VLAN entries remained
installed in the hardware database of the switchdev port.
Also, since commit 0d2cfbd41c4a ("net: bridge: ignore switchdev events
for LAG ports which didn't request replay"), DSA introduced a method,
based on a const void *ctx, to ensure that two switchdev ports under the
same LAG that is a bridge port do not see the same MDB/VLAN entry being
replayed twice by the bridge, once for every bridge port that joins the
LAG.
With so many ordering corner cases being possible, it seems unreasonable
to expect a switchdev driver writer to get it right from the first try.
Therefore, now that DSA has experimented with the bridge replay helpers
for a little bit, we can move the code to the bridge driver where it is
more readily available to all switchdev drivers.
To convert the switchdev object replay helpers from "pull mode" (where
the driver asks for them) to a "push mode" (where the bridge offers them
automatically), the biggest problem is that the bridge needs to be aware
when a switchdev port joins and leaves, even when the switchdev is only
indirectly a bridge port (for example when the bridge port is a LAG
upper of the switchdev).
Luckily, we already have a hook for that, in the form of the newly
introduced switchdev_bridge_port_offload() and
switchdev_bridge_port_unoffload() calls. These offer a natural place for
hooking the object addition and deletion replays.
Extend the above 2 functions with:
- pointers to the switchdev atomic notifier (for FDB replays) and the
blocking notifier (for MDB and VLAN replays).
- the "const void *ctx" argument required for drivers to be able to
disambiguate between which port is targeted, when multiple ports are
lowers of the same LAG that is a bridge port. Most of the drivers pass
NULL to this argument, except the ones that support LAG offload and have
the proper context check already in place in the switchdev blocking
notifier handler.
Also unexport the replay helpers, since nobody except the bridge calls
them directly now.
Note that:
(a) we abuse the terminology slightly, because FDB entries are not
"switchdev objects", but we count them as objects nonetheless.
With no direct way to prove it, I think they are not modeled as
switchdev objects because those can only be installed by the bridge
to the hardware (as opposed to FDB entries which can be propagated
in the other direction too). This is merely an abuse of terms, FDB
entries are replayed too, despite not being objects.
(b) the bridge does not attempt to sync port attributes to newly joined
ports, just the countable stuff (the objects). The reason for this
is simple: no universal and symmetric way to sync and unsync them is
known. For example, VLAN filtering: what to do on unsync, disable or
leave it enabled? Similarly, STP state, ageing timer, etc etc. What
a switchdev port does when it becomes standalone again is not really
up to the bridge's competence, and the driver should deal with it.
On the other hand, replaying deletions of switchdev objects can be
seen a matter of cleanup and therefore be treated by the bridge,
hence this patch.
We make the replay helpers opt-in for drivers, because they might not
bring immediate benefits for them:
- nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(),
so br_vlan_replay() should not do anything for the new drivers on
which we call it. The existing drivers where there was even a slight
possibility for there to exist a VLAN on a bridge port before they
join it are already guarded against this: mlxsw and prestera deny
joining LAG interfaces that are members of a bridge.
- br_fdb_replay() should now notify of local FDB entries, but I patched
all drivers except DSA to ignore these new entries in commit
2c4eca3ef716 ("net: bridge: switchdev: include local flag in FDB
notifications"). Driver authors can lift this restriction as they
wish, and when they do, they can also opt into the FDB replay
functionality.
- br_mdb_replay() should fix a real issue which is described in commit
4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined
mdb entries"). However most drivers do not offload the
SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw
offload this switchdev object, and I don't completely understand the
way in which they offload this switchdev object anyway. So I'll leave
it up to these drivers' respective maintainers to opt into
br_mdb_replay().
So most of the drivers pass NULL notifier blocks for the replay helpers,
except:
- dpaa2-switch which was already acked/regression-tested with the
helpers enabled (and there isn't much of a downside in having them)
- ocelot which already had replay logic in "pull" mode
- DSA which already had replay logic in "pull" mode
An important observation is that the drivers which don't currently
request bridge event replays don't even have the
switchdev_bridge_port_{offload,unoffload} calls placed in proper places
right now. This was done to avoid unnecessary rework for drivers which
might never even add support for this. For driver writers who wish to
add replay support, this can be used as a tentative placement guide:
https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a desire to make the object and FDB replay helpers optional
when moving them inside the bridge driver. For example a certain driver
might not offload host MDBs and there is no case where the replay
helpers would be of immediate use to it.
So it would be nice if we could allow drivers to pass NULL pointers for
the atomic and blocking notifier blocks, and the replay helpers to do
nothing in that case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On reception of an skb, the bridge checks if it was marked as 'already
forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it
is, it assigns the source hardware domain of that skb based on the
hardware domain of the ingress port. Then during forwarding, it enforces
that the egress port must have a different hardware domain than the
ingress one (this is done in nbp_switchdev_allowed_egress).
Non-switchdev drivers don't report any physical switch id (neither
through devlink nor .ndo_get_port_parent_id), therefore the bridge
assigns them a hardware domain of 0, and packets coming from them will
always have skb->offload_fwd_mark = 0. So there aren't any restrictions.
Problems appear due to the fact that DSA would like to perform software
fallback for bonding and team interfaces that the physical switch cannot
offload.
+-- br0 ---+
/ / | \
/ / | \
/ | | bond0
/ | | / \
swp0 swp1 swp2 swp3 swp4
There, it is desirable that the presence of swp3 and swp4 under a
non-offloaded LAG does not preclude us from doing hardware bridging
beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high
enough that software bridging between {swp0,swp1,swp2} and bond0 is not
impractical.
But this creates an impossible paradox given the current way in which
port hardware domains are assigned. When the driver receives a packet
from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to
something.
- If we set it to 0, then the bridge will forward it towards swp1, swp2
and bond0. But the switch has already forwarded it towards swp1 and
swp2 (not to bond0, remember, that isn't offloaded, so as far as the
switch is concerned, ports swp3 and swp4 are not looking up the FDB,
and the entire bond0 is a destination that is strictly behind the
CPU). But we don't want duplicated traffic towards swp1 and swp2, so
it's not ok to set skb->offload_fwd_mark = 0.
- If we set it to 1, then the bridge will not forward the skb towards
the ports with the same switchdev mark, i.e. not to swp1, swp2 and
bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should
have forwarded the skb there.
So the real issue is that bond0 will be assigned the same hardware
domain as {swp0,swp1,swp2}, because the function that assigns hardware
domains to bridge ports, nbp_switchdev_add(), recurses through bond0's
lower interfaces until it finds something that implements devlink (calls
dev_get_port_parent_id with bool recurse = true). This is a problem
because the fact that bond0 can be offloaded by swp3 and swp4 in our
example is merely an assumption.
A solution is to give the bridge explicit hints as to what hardware
domain it should use for each port.
Currently, the bridging offload is very 'silent': a driver registers a
netdevice notifier, which is put on the netns's notifier chain, and
which sniffs around for NETDEV_CHANGEUPPER events where the upper is a
bridge, and the lower is an interface it knows about (one registered by
this driver, normally). Then, from within that notifier, it does a bunch
of stuff behind the bridge's back, without the bridge necessarily
knowing that there's somebody offloading that port. It looks like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v
call_netdevice_notifiers
|
v
dsa_slave_netdevice_event
|
v
oh, hey! it's for me!
|
v
.port_bridge_join
What we do to solve the conundrum is to be less silent, and change the
switchdev drivers to present themselves to the bridge. Something like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | hardware domain for
v | this port, and zero
dsa_slave_netdevice_event | if I got nothing.
| |
v |
oh, hey! it's for me! |
| |
v |
.port_bridge_join |
| |
+------------------------+
switchdev_bridge_port_offload(swp0, swp0)
Then stacked interfaces (like bond0 on top of swp3/swp4) would be
treated differently in DSA, depending on whether we can or cannot
offload them.
The offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | switchdev mark for
v | bond0.
dsa_slave_netdevice_event | Coincidentally (or not),
| | bond0 and swp0, swp1, swp2
v | all have the same switchdev
hmm, it's not quite for me, | mark now, since the ASIC
but my driver has already | is able to forward towards
called .port_lag_join | all these ports in hw.
for it, because I have |
a port with dp->lag_dev == bond0. |
| |
v |
.port_bridge_join |
for swp3 and swp4 |
| |
+------------------------+
switchdev_bridge_port_offload(bond0, swp3)
switchdev_bridge_port_offload(bond0, swp4)
And the non-offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge waiting:
call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload
| | wasn't called, okay, I'll use a
v | hwdom of zero for this one.
dsa_slave_netdevice_event : Then packets received on swp0 will
| : not be software-forwarded towards
v : swp1, but they will towards bond0.
it's not for me, but
bond0 is an upper of swp3
and swp4, but their dp->lag_dev
is NULL because they couldn't
offload it.
Basically we can draw the conclusion that the lowers of a bridge port
can come and go, so depending on the configuration of lowers for a
bridge port, it can dynamically toggle between offloaded and unoffloaded.
Therefore, we need an equivalent switchdev_bridge_port_unoffload too.
This patch changes the way any switchdev driver interacts with the
bridge. From now on, everybody needs to call switchdev_bridge_port_offload
and switchdev_bridge_port_unoffload, otherwise the bridge will treat the
port as non-offloaded and allow software flooding to other ports from
the same ASIC.
Note that these functions lay the ground for a more complex handshake
between switchdev drivers and the bridge in the future.
For drivers that will request a replay of the switchdev objects when
they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we
place the call to switchdev_bridge_port_unoffload() strategically inside
the NETDEV_PRECHANGEUPPER notifier's code path, and not inside
NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers
need the netdev adjacency lists to be valid, and that is only true in
NETDEV_PRECHANGEUPPER.
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since hwdoms have only been used thus far for equality comparisons, the
bridge has used the simplest possible assignment policy; using a
counter to keep track of the last value handed out.
With the upcoming transmit offloading, we need to perform set
operations efficiently based on hwdoms, e.g. we want to answer
questions like "has this skb been forwarded to any port within this
hwdom?"
Move to a bitmap-based allocation scheme that recycles hwdoms once all
members leaves the bridge. This means that we can use a single
unsigned long to keep track of the hwdoms that have received an skb.
v1->v2: convert the typedef DECLARE_BITMAP(br_hwdom_map_t, BR_HWDOM_MAX)
into a plain unsigned long.
v2->v6: none
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this change, four related - but distinct - concepts where named
offload_fwd_mark:
- skb->offload_fwd_mark: Set by the switchdev driver if the underlying
hardware has already forwarded this frame to the other ports in the
same hardware domain.
- nbp->offload_fwd_mark: An idetifier used to group ports that share
the same hardware forwarding domain.
- br->offload_fwd_mark: Counter used to make sure that unique IDs are
used in cases where a bridge contains ports from multiple hardware
domains.
- skb->cb->offload_fwd_mark: The hardware domain on which the frame
ingressed and was forwarded.
Introduce the term "hardware forwarding domain" ("hwdom") in the
bridge to denote a set of ports with the following property:
If an skb with skb->offload_fwd_mark set, is received on a port
belonging to hwdom N, that frame has already been forwarded to all
other ports in hwdom N.
By decoupling the name from "offload_fwd_mark", we can extend the
term's definition in the future - e.g. to add constraints that
describe expected egress behavior - without overloading the meaning of
"offload_fwd_mark".
- nbp->offload_fwd_mark thus becomes nbp->hwdom.
- br->offload_fwd_mark becomes br->last_hwdom.
- skb->cb->offload_fwd_mark becomes skb->cb->src_hwdom. The slight
change in naming here mandates a slight change in behavior of the
nbp_switchdev_frame_mark() function. Previously, it only set this
value in skb->cb for packets with skb->offload_fwd_mark true (ones
which were forwarded in hardware). Whereas now we always track the
incoming hwdom for all packets coming from a switchdev (even for the
packets which weren't forwarded in hardware, such as STP BPDUs, IGMP
reports etc). As all uses of skb->cb->offload_fwd_mark were already
gated behind checks of skb->offload_fwd_mark, this will not introduce
any functional change, but it paves the way for future changes where
the ingressing hwdom must be known for frames coming from a switchdev
regardless of whether they were forwarded in hardware or not
(basically, if the skb comes from a switchdev, skb->cb->src_hwdom now
always tracks which one).
A typical example where this is relevant: the switchdev has a fixed
configuration to trap STP BPDUs, but STP is not running on the bridge
and the group_fwd_mask allows them to be forwarded. Say we have this
setup:
br0
/ | \
/ | \
swp0 swp1 swp2
A BPDU comes in on swp0 and is trapped to the CPU; the driver does not
set skb->offload_fwd_mark. The bridge determines that the frame should
be forwarded to swp{1,2}. It is imperative that forward offloading is
_not_ allowed in this case, as the source hwdom is already "poisoned".
Recording the source hwdom allows this case to be handled properly.
v2->v3: added code comments
v3->v6: none
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make more room for some extra code in the NETDEV_PRECHANGEUPPER handler
by moving what already exists into a dedicated function.
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to propagate the extack argument for
dpaa2_switch_port_bridge_join to use it in a future patch, and it looks
like there is already an error message there which is currently printed
to the console. Move it over netlink so it is properly transmitted to
user space.
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lino Sanfilippo says:
====================
Fixes for KSZ DSA switch
These patches fix issues I encountered while using a KSZ9897 as a DSA
switch with a broadcom GENET network device as the DSA master device.
PATCH 1 fixes an invalid access to an SKB in case it is scattered.
PATCH 2 fixes incorrect hardware checksum calculation caused by the DSA
tag.
Changes in v2:
- instead of linearizing the SKBs only for KSZ switches ensure linearized
SKBs for all tail taggers by clearing the feature flags NETIF_F_HW_SG and
NETIF_F_FRAGLIST (suggested by Vladimir Oltean)
The patches have been tested with a KSZ9897 and apply against net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the checksum calculation is offloaded to the network device (e.g due to
NETIF_F_HW_CSUM inherited from the DSA master device), the calculated
layer 4 checksum is incorrect. This is since the DSA tag which is placed
after the layer 4 data is considered as being part of the daa and thus
errorneously included into the checksum calculation.
To avoid this, always calculate the layer 4 checksum in software.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function skb_put() that is used by tail taggers to make room for the
DSA tag must only be called for linearized SKBS. However in case that the
slave device inherited features like NETIF_F_HW_SG or NETIF_F_FRAGLIST the
SKB passed to the slaves transmit function may not be linearized.
Avoid those SKBs by clearing the NETIF_F_HW_SG and NETIF_F_FRAGLIST flags
for tail taggers.
Furthermore since the tagging protocol can be changed at runtime move the
code for setting up the slaves features into dsa_slave_setup_tagger().
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Requiring that initrd is loaded below RAM start + 256 MiB led to failure
to boot SUSE Linux with GRUB on QEMU, cf.
https://lists.gnu.org/archive/html/grub-devel/2021-06/msg00037.html
Remove the constraint.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Fixes: d7071743db31 ("RISC-V: Add EFI stub support.")
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Align the member description comments for struct ravb_desc by
removing the extra TAB.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the typo RX->TX in comment, as the code following the comment
process TX and not RX.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
