| Age | Commit message (Collapse) | Author |
|---|
|
The host physical addresses of L1's Virtual APIC Page and Posted
Interrupt descriptor are loaded into the VMCS02. The CPU may write
to these pages via their host physical address while L2 is running,
bypassing address-translation-based dirty tracking (e.g. EPT write
protection). Mark them dirty on every exit from L2 to prevent them
from getting out of sync with dirty tracking.
Also mark the virtual APIC page and the posted interrupt descriptor
dirty when KVM is virtualizing posted interrupt processing.
Signed-off-by: David Matlack <dmatlack@google.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
According to the Intel SDM, software cannot rely on the current VMCS to be
coherent after a VMXOFF or shutdown. So this is a valid way to handle VMCS12
flushes.
24.11.1 Software Use of Virtual-Machine Control Structures
...
If a logical processor leaves VMX operation, any VMCSs active on
that logical processor may be corrupted (see below). To prevent
such corruption of a VMCS that may be used either after a return
to VMX operation or on another logical processor, software should
execute VMCLEAR for that VMCS before executing the VMXOFF instruction
or removing power from the processor (e.g., as part of a transition
to the S3 and S4 power states).
...
This fixes a "suspicious rcu_dereference_check() usage!" warning during
kvm_vm_release() because nested_release_vmcs12() calls
kvm_vcpu_write_guest_page() without holding kvm->srcu.
Signed-off-by: David Matlack <dmatlack@google.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Since the current implementation of VMCS12 does a memcpy in and out
of guest memory, we do not need current_vmcs12 and current_vmcs12_page
anymore. current_vmptr is enough to read and write the VMCS12.
And David Matlack noted:
This patch also fixes dirty tracking (memslot->dirty_bitmap) of the
VMCS12 page by using kvm_write_guest. nested_release_page() only marks
the struct page dirty.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[Added David Matlack's note and nested_release_page_clean() fix.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
During teardown, accesses to memslots and buses are using
rcu_dereference_protected with an always-true condition because
these accesses are done outside the usual mutexes. This
is because the last reference is gone and there cannot be any
concurrent modifications, but rcu_dereference_protected is
ugly and unobvious.
Instead, check the refcount in kvm_get_bus and __kvm_memslots.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
'lapic_irq' is a local variable and its 'level' field isn't
initialized, so 'level' is random, it doesn't matter but
makes UBSAN unhappy:
UBSAN: Undefined behaviour in .../lapic.c:...
load of value 10 is not a valid value for type '_Bool'
...
Call Trace:
[<ffffffff81f030b6>] dump_stack+0x1e/0x20
[<ffffffff81f03173>] ubsan_epilogue+0x12/0x55
[<ffffffff81f03b96>] __ubsan_handle_load_invalid_value+0x118/0x162
[<ffffffffa1575173>] kvm_apic_set_irq+0xc3/0xf0 [kvm]
[<ffffffffa1575b20>] kvm_irq_delivery_to_apic_fast+0x450/0x910 [kvm]
[<ffffffffa15858ea>] kvm_irq_delivery_to_apic+0xfa/0x7a0 [kvm]
[<ffffffffa1517f4e>] kvm_emulate_hypercall+0x62e/0x760 [kvm]
[<ffffffffa113141a>] handle_vmcall+0x1a/0x30 [kvm_intel]
[<ffffffffa114e592>] vmx_handle_exit+0x7a2/0x1fa0 [kvm_intel]
...
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
When SMP VM start, AP may lost INIT because of receiving INIT between
kvm_vcpu_ioctl_x86_get/set_vcpu_events.
vcpu 0 vcpu 1
kvm_vcpu_ioctl_x86_get_vcpu_events
events->smi.latched_init = 0
send INIT to vcpu1
set vcpu1's pending_events
kvm_vcpu_ioctl_x86_set_vcpu_events
if (events->smi.latched_init == 0)
clear INIT in pending_events
This patch fixes it by just update SMM related flags if we are in SMM.
Thanks Peng Hao for the report and original commit message.
Reported-by: Peng Hao <peng.hao2@zte.com.cn>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Otherwise bo->shadow_list (which is aliased by bo->mn_list) will not
appear empty in amdgpu_ttm_bo_destroy and cause an oops when freeing
former userptr BOs.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
As I was staring at the si_init_golden_registers code, I noticed that
the Pitcairn initialization silently falls through the Cape Verde
initialization, and the Oland initialization falls through the Hainan
initialization. However there is no comment stating that this is
intentional, and the radeon driver doesn't have any such fallthrough,
so I suspect this is not supposed to happen.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 62a37553414a ("drm/amdgpu: add si implementation v10")
Cc: Ken Wang <Qingqing.Wang@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Marek Olšák" <maraeo@gmail.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
If the sender switches the congestion control during ECN-triggered
cwnd-reduction state (CA_CWR), upon exiting recovery cwnd is set to
the ssthresh value calculated by the previous congestion control. If
the previous congestion control is BBR that always keep ssthresh
to TCP_INIFINITE_SSTHRESH, cwnd ends up being infinite. The safe
step is to avoid assigning invalid ssthresh value when recovery ends.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCRQ resources are freed during renegotiation, but they are not
re-allocated afterwards due to some changes in the initialization
process. Fix that by re-allocating the memory after renegotation.
SCRQ's can also be freed if a server capabilities request fails.
If this were encountered during a device reset for example,
SCRQ's may not be re-allocated. This operation is not necessary
anymore so remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tariq Toukan says:
====================
mlx4 misc fixes
This patchset contains misc bug fixes from the team
to the mlx4 Core and Eth drivers.
Patch 1 by Inbar fixes a wrong ethtool indication for Wake-on-LAN.
The other 3 patches by Jack add a missing capability description,
and fixes the off-by-1 misalignment for the following capabilities
descriptions.
Series generated against net commit:
cc75f8514db6 samples/bpf: fix bpf tunnel cleanup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:
QUERY_DEV_CAP_DIAG_RPRT_PER_PORT
However, it failed to introduce a corresponding entry in function
dump_dev_cap_flags2() for outputting a line in the message log
when this capability bit is set.
The change here fixes that omission.
Fixes: c7c122ed67e4 ("net/mlx4: Add diagnostic counters capability bit")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:
MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP
However the value of MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP needs to stay
consistent with the value used in another namespace in
function dump_dev_cap_flags2(), which is manually kept in sync.
The change here restores that consistency.
Fixes: 7c3d21c8153c ("net/mlx4_core: Preparation for VF vlan protocol 802.1ad")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The index value in function dump_dev_cap_flags2() for outputting
"sl to vl mapping table change event support" needs to be
consistent with the value of the enumerated constant
MLX4_DEV_CAP_FLAG2_SL_TO_VL_CHANGE_EVENT defined in file
include/linux/mlx4_device.h
The change here restores that consistency.
Fixes: fd10ed8e6f42 ("IB/mlx4: Fix possible vl/sl field mismatch in LRH header in QP1 packets")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when WoL is supported but disabled, ethtool reports:
"Supports Wake-on: d".
Fix the indication of Wol support, so that the indication
remains "g" all the time if the NIC supports WoL.
Tested:
As accepted, when NIC supports WoL- ethtool reports:
Supports Wake-on: g
Wake-on: d
when NIC doesn't support WoL- ethtool reports:
Supports Wake-on: d
Wake-on: d
Fixes: 14c07b1358ed ("mlx4: Wake on LAN support")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nisar Sayed says:
====================
lan78xx: Fixes to lan78xx driver
This series of patches are for lan78xx driver.
These patches fixes potential issues associated with lan78xx driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to handle hard_header_len update
When ifconfig up/down sequence is initiated hard_header_len
get updated incrementally for each ifconfig up /down sequence,
this leads invalid hard_header_len, moving to lan78xx_bind
to have one time update of hard_header_len addresses the issue.
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
USB fast connect/disconnect crash fix
When USB plugged/unplugged at fast rate,
lan78xx_mdio_init() in lan78xx_bind() failing case is not handled.
Whenever lan78xx_mdio_init() failed, dev->mdiobus will be freed, however
since lan78xx_bind() not consider as error and try to proceed for
further initialization in lan78xx_probe() which leads system hung/crash.
Also when register_netdev() failed, netdev is freed without calling lan78xx_unbind().
Hence halting the failed cases right manner fixes the system crash/hung issue.
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Renesas uPD72020x XHCI controller seems to suffer from a really
annoying bug, where it may retain some of its DMA programming across a XHCI
reset, and despite the driver correctly programming new DMA addresses.
This is visible if the device has been using 64-bit DMA addresses, and is
then switched to using 32-bit DMA addresses. The top 32 bits of the
address (now zero) are ignored are replaced by the 32 bits from the
*previous* programming. Sticking with 64-bit DMA always works, but doesn't
seem very appropriate.
A PCI reset of the device restores the normal functionality, which is done
at probe time. Unfortunately, this has to be done before any quirk has
been discovered, hence the intrusive nature of the fix.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: stable@vger.kernel.org # v4.11+
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Fix two bugs under error or abnormal usage conditions. Correct a
config dependency:
dell-wmi:
- Fix driver interface version query
wmi:
- Fix error handling in acpi_wmi_init()
peaq-wmi:
- select INPUT_POLLDEV"
* tag 'platform-drivers-x86-v4.13-3' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: dell-wmi: Fix driver interface version query
platform/x86: wmi: Fix error handling in acpi_wmi_init()
platform/x86: peaq-wmi: select INPUT_POLLDEV
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull one Allwinner clock fix from Chen-Yu Tsai:
One critical clock fix for sun5i (A10s/A13/R8) which enables propagation
of clock rate changes from the "cpu" clock to it's parent PLL clock.
This fixes cpufreq related crashes that have been observed on KernelCI
with the C.H.I.P. and multi_v7_defconfig.
* tag 'sunxi-clk-fixes-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: sun5i: Add clk_set_rate_parent to the CPU clock
|
|
git://github.com/baylibre/clk-meson into clk-fixes
Pull one Meson clock fix from Neil Armstrong
* tag 'meson-clk-fixes-for-4.13-rc4-v2' of git://github.com/baylibre/clk-meson:
clk: meson: mpll: fix mpll0 fractional part ignored
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"These seven patches are mostly minor build, Kconfig and error leg
fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qedi: Fix return code in qedi_ep_connect()
scsi: lpfc: fix linking against modular NVMe support
scsi: scsi_transport_fc: return -EBUSY for deleted vport
scsi: libcxgbi: add check for valid cxgbi_task_data
scsi: aic7xxx: fix firmware build with O=path
scsi: megaraid_sas: fix memleak in megasas_alloc_cmdlist_fusion
scsi: qedi: Add ISCSI_BOOT_SYSFS to Kconfig
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.13
Quite a few fixes here that have been sent since the merge window, the
biggest one is the fix from Tony for some confusion with the device
property API which was causing issues with the of-graph card. This is
fixed with some changes in the graph API itself as it seemed very likely
to be error prone.
|
|
When blk_mq_get_request() failed, preempt counter isn't
released, and blk_mq_make_request() doesn't release the counter
too.
This patch fixes the issue, and makes sure that preempt counter
is only held if rq is allocated successfully. The same policy is
applied on .q_usage_counter too.
Signed-off-by: Ming Lei <minlei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The number of pins in South Bridge is 30 and not 29. There is a fix for
the driver for the pinctrl, but a fix is also need at device tree level
for the GPIO.
Fixes: afda007feda5 ("ARM64: dts: marvell: Add pinctrl nodes for Armada
3700")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
rpc_clnt_add_xprt() expects the callback function to be synchronous, and
expects to release the transport and switch references itself.
Fixes: 04fa2c6bb51b1 ("NFS pnfs data server multipath session trunking")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
Sony VAIO VPCL14M1R needs the quirk to make the speaker working properly.
Tested-by: Dmitriy <mexx400@yandex.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
of_irq_to_resource() has recently been fixed to return negative error #'s
along with 0 in case of failure, however the Freescale MPC832x RDB board
code still only regards 0 as a failure indication -- fix it up.
Fixes: 7a4228bbff76 ("of: irq: use of_irq_get() in of_irq_to_resource()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When more than one GPIO IRQs are triggered simultaneously,
tegra_gpio_irq_handler() called chained_irq_exit() multiple
times for one chained_irq_enter().
Fixes: 3c92db9ac0ca3eee8e46e2424b6c074e2e394ad9
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
[Also changed the variable to a bool]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
EDO mode should be used when tRC is less than 30ns, but timings are
expressed in picoseconds in the nand_sdr_timings struct.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: f9ce2eddf176 ("mtd: nand: atmel: Add ->setup_data_interface() hooks")
Reported-by: Alexander Dahl <ada@thorsis.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
All timings in nand_sdr_timings are expressed in picoseconds but some
of them may not fit in an u32.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 204e7ecd47e2 ("mtd: nand: Add a few more timings to nand_sdr_timings")
Reported-by: Alexander Dahl <ada@thorsis.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Some ONFI NANDs do not support the SET/GET FEATURES commands, which,
according to the spec, is perfectly valid.
On these NANDs we can't set a specific timing mode using the "timing
mode" feature, and we should assume the NAND does not require any setup
to enter a specific timing mode.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d8e725dd8311 ("mtd: nand: automate NAND timings selection")
Reported-by: Alexander Dahl <ada@thorsis.com>
Cc: <stable@vger.kernel.org>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Commit 0b4773fd1649 (mtd: nand: Drop unused cached programming support)
removed the "cached" parameter from nand_write_page(), but did not update
the kerneldoc comments, creating this docs build warning:
./drivers/mtd/nand/nand_base.c:2751: warning: Excess function parameter 'cached' description in 'nand_write_page'
Remove the offending line so we can have a little peace and quiet.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
clk_round_rate() can return <= 0. Currently the value returned by
clk_round_rate() is used directly for a division. This patch introduces a
guard to ensure a divide-by-zero or a divide by a negative number for that
matter can't happen by bugging out returning -EINVAL if clk_round_rate()
returns <= 0.
Fixes: 2d43457f79e4 ("mtd: nand: sunxi: fix EDO mode selection")
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
When using soft ecc, if no ooblayout is given, the core automatically
uses one of the nand_ooblayout_{sp,lp}*() functions to determine the
layout inside the out of band data.
Until kernel version 4.6, struct nand_ecclayout was used for that
purpose. During the migration from 4.6 to 4.7, an error shown up in the
small page layout, in the case oob section is only 8 bytes long.
The layout was using three bytes (0, 1, 2) for ecc, two bytes (3, 4)
as free bytes, one byte (5) for bad block marker and finally
two bytes (6, 7) as free bytes, as shown there:
[linux-4.6] drivers/mtd/nand/nand_base.c:52
static struct nand_ecclayout nand_oob_8 = {
.eccbytes = 3,
.eccpos = {0, 1, 2},
.oobfree = {
{.offset = 3,
.length = 2},
{.offset = 6,
.length = 2} }
};
This fixes the current implementation which is incoherent. It
references bit 3 at the same time as an ecc byte and a free byte.
Furthermore, it is clear with the previous implementation that there
is only one ecc section with 8 bytes oob sections. We shall return
-ERANGE in the nand_ooblayout_ecc_sp() function when asked for the
second section.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Fixes: 41b207a70d3a ("mtd: nand: implement the default mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Florian Fainelli says:
====================
drivers: net: Fix 64-bit statistics seqcount init
This patch series fixes a bunch of drivers to have their 64-bit statistics
seqcount cookie be initialized correctly. Most of these drivers (except b44,
gtp) are probably used on 64-bit only hosts and so the lockdep splat might have
never been seen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that by using the proper helper function: netdev_alloc_pcpu_stats().
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that. In commit 6c80f3fc2398 ("netvsc: report per-channel stats in
ethtool statistics") netdev_alloc_pcpu_stats() was removed in favor of
open-coding the 64-bits statistics, except that u64_stats_init() was
missed.
Fixes: 6c80f3fc2398 ("netvsc: report per-channel stats in ethtool statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that by using netdev_alloc_pcpu_stats() instead of an open coded
allocation.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that.
Fixes: 4c3523623dc0 ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that.
Fixes: 4197aa7bb818 ("ixgbevf: provide 64 bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that.
Fixes: 980e9b118642 ("i40e: Add support for 64 bit netstats")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that.
Fixes: eeda8585522b ("b44: add 64 bit stats")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a workload caused a HW GPU hang or it is in the middle of
vGPU reset, the workload queue should be cleaned up to emulate
the hang state of the GPU.
v2:
- use ENGINE_MASK(ring_id) instead of (1 << ring_id). (Zhenyu)
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
Use resetting_eng to identify which engine is resetting
so the rest ones' workload won't be impacted
v2:
- use ENGINE_MASK(ring_id) instead of (1 << ring_id). (Zhenyu)
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
The implementation of PCI workarounds may require that the device is reset
from its probe function. This implies that the PCI device lock is already
held, and makes calling pci_reset_function() impossible (since it will
itself try to take that lock).
Add pci_reset_function_locked(), which is the equivalent of
pci_reset_function(), except that it requires the PCI device lock to be
already held by the caller.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[bhelgaas: folded in fix for conflict with 52354b9d1f46 ("PCI: Remove
__pci_dev_reset() and pci_dev_reset()")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # 4.11: 52354b9d1f46: PCI: Remove __pci_dev_reset() and pci_dev_reset()
Cc: stable@vger.kernel.org # 4.11
|
|
In zap_shader_load_mdt(), we pass a pointer to a phys_addr_t
into dmam_alloc_coherent, which the compiler warns about:
drivers/gpu/drm/msm/adreno/a5xx_gpu.c: In function 'zap_shader_load_mdt':
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:54:50: error: passing argument 3 of 'dmam_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
The returned DMA address is later passed on to a function that
takes a phys_addr_t, so it's clearly wrong to use the DMA
mapping interface here: the memory may be uncached, or the
address may be completely wrong if there is an IOMMU connected
to the device. What the code actually wants to do is to get
the physical address from the reserved-mem node. It goes through
the dma-mapping interfaces for obscure reasons, and this
apparently only works by chance, relying on specific bugs
in the error handling of the arm64 dma-mapping implementation.
The same problem existed in the "venus" media driver, which was
now fixed by Stanimir Varbanov after long discussions.
In order to make some progress here, I have now ported his
approach over to the adreno driver. The patch is currently
untested, and should get a good review, but it is now much
simpler than the original, and it should be obvious what
goes wrong if I made a mistake in the port.
See also: a6e2d36bf6b7 ("media: venus: don't abuse dma_alloc for non-DMA allocations")
Cc: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Fixes: 7c65817e6d38 ("drm/msm: gpu: Enable zap shader for A5XX")
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-and-Tested-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
When compile-testing for something other than ARCH_QCOM,
we run into a link error:
drivers/gpu/drm/msm/adreno/a5xx_gpu.o: In function `a5xx_hw_init':
a5xx_gpu.c:(.text.a5xx_hw_init+0x600): undefined reference to `qcom_mdt_get_size'
a5xx_gpu.c:(.text.a5xx_hw_init+0x93c): undefined reference to `qcom_mdt_load'
There is already an #ifdef that tries to check for CONFIG_QCOM_MDT_LOADER,
but that symbol is only meaningful when building for ARCH_QCOM.
This adds a compile-time check for ARCH_QCOM, and clarifies the
Kconfig select statement so we don't even try it for other targets.
The check for CONFIG_QCOM_MDT_LOADER can then go away, which also
improves compile-time coverage and makes the code a little nicer
to read.
Fixes: 7c65817e6d38 ("drm/msm: gpu: Enable zap shader for A5XX")
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
