| Age | Commit message (Collapse) | Author |
|---|
|
If we're trying to allocate real space for a delalloc reservation at
offset 0, we should use the rotor to spread files across the rt volume.
Switch the rtalloc to use the XFS_ALLOC_INITIAL_USER_DATA flag that
is set for any write at startoff to make it match the behavior for
the main data device.
Based on a patch from Darrick J. Wong.
Fixes: 6a94b1acda7e ("xfs: reinstate delalloc for RT inodes (if sb_rextsize == 1)")
Reported-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
|
|
Bartosz Golaszewski says:
====================
net: stmmac: qcom-ethqos: enable 2.5G ethernet on sa8775p-ride
Here are the changes required to enable 2.5G ethernet on sa8775p-ride.
As advised by Andrew Lunn and Russell King, I am reusing the existing
stmmac infrastructure to enable the SGMII loopback and so I dropped the
patches adding new callbacks to the driver core. I also added more
details to the commit message and made sure the workaround is only
enabled on Rev 3 of the board (with AQR115C PHY). Also: dropped any
mentions of the OCSGMII mode.
v2: https://lore.kernel.org/20240627113948.25358-1-brgl@bgdev.pl
v1: https://lore.kernel.org/20240619184550.34524-1-brgl@bgdev.pl
====================
Link: https://patch.msgid.link/20240703181500.28491-1-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
sa8775p-ride-r3
On sa8775p-ride-r3 the RX clocks from the AQR115C PHY are not available at
the time of the DMA reset. We can however extract the RX clock from the
internal SERDES block. Once the link is up, we can revert to the
previous state.
The AQR115C PHY doesn't support in-band signalling so we can count on
getting the link up notification and safely reuse existing callbacks
which are already used by another HW quirk workaround which enables the
functional clock to avoid a DMA reset due to timeout.
Only enable loopback on revision 3 of the board - check the phy_mode to
make sure.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240703181500.28491-3-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for 2.5G speed in 2500BASEX mode to the QCom ethqos driver.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240703181500.28491-2-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reinit PHY after cable test, otherwise link can't be established on
tested port. This issue is reproducible on LAN9372 switches with
integrated 100BaseT1 PHYs.
Fixes: 788050256c411 ("net: phy: microchip_t1: add cable test support for lan87xx phy")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240705084954.83048-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
WARN_ON_ONCE("string") doesn't really do what appears to
be intended, so fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 90de47f020db ("page_pool: fragment API support for 32-bit arch with 64-bit DMA")
Link: https://patch.msgid.link/20240705134221.2f4de205caa1.I28496dc0f2ced580282d1fb892048017c4491e21@changeid
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Building this driver yields the following:
.../drivers/cpufreq/sti-cpufreq.c:215:50: warning: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size 2 [-Wformat-truncation=]
215 | snprintf(name, MAX_PCODE_NAME_LEN, pcode%d, pcode);
| ^~
.../drivers/cpufreq/sti-cpufreq.c:215:44: note: directive argument in the range [0, 2147483647]
215 | snprintf(name, MAX_PCODE_NAME_LEN, pcode%d, pcode);
| ^~~~~~~~~
.../drivers/cpufreq/sti-cpufreq.c:215:9: note: ‘snprintf’ output between 7 and 16 bytes into a destination of size 7
215 | snprintf(name, MAX_PCODE_NAME_LEN, pcode%d, pcode);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix the buffer size to avoid the warning at build time.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Use the dev_err_probe() helper to log the errors on every error path in
the probe function and its sub-functions. This includes
* adding error messages where there was none
* converting over dev_err/dev_warn
* removing the top-level error message after mtk_cpu_dvfs_info_init() is
called, since every error path inside that function already logs the
error reason. This gets rid of the misleading error message when probe
is deferred:
mtk-cpufreq mtk-cpufreq: failed to initialize dvfs info for cpu0
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Some of LoongArch processors (Loongson-3 series) support DVFS, their
IOCSR.FEATURES has IOCSRF_FREQSCALE set. And they has a micro-core in
the package called SMC (System Management Controller), which can be
used to detect temperature, control fans, scale frequency and voltage,
etc.
The Loongson-3 CPUFreq driver is very simple now, it communicate with
SMC, get DVFS info, set target frequency from CPUFreq core, and so on.
There is a command list to interact with SMC, widely-used commands in
the CPUFreq driver include:
CMD_GET_VERSION: Get SMC firmware version.
CMD_GET_FEATURE: Get enabled SMC features.
CMD_SET_FEATURE: Enable SMC features, such as basic DVFS, BOOST.
CMD_GET_FREQ_LEVEL_NUM: Get the number of all frequency levels.
CMD_GET_FREQ_BOOST_LEVEL: Get the first boost frequency level.
CMD_GET_FREQ_LEVEL_INFO: Get the detail info of a frequency level.
CMD_GET_FREQ_INFO: Get the current frequency.
CMD_SET_FREQ_INFO: Set the target frequency.
In future we will add automatic frequency scaling, which is similar to
Intel's HWP (HardWare P-State).
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
[ Viresh: Minor formatting cleanups, change return type of exit() to
void and use devm_mutex_init() ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The cpufreq core doesn't check the return type of the exit() callback
and there is not much the core can do on failures at that point. Just
drop the returned value and make it return void.
Signed-off-by: Lizhe <sensor1010@163.com>
[ Viresh: Reworked the patches to fix all missing changes together. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> # Mediatek
Acked-by: Sudeep Holla <sudeep.holla@arm.com> # scpi, scmi, vexpress
Acked-by: Mario Limonciello <mario.limonciello@amd.com> # amd
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> # bmips
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com> # omap
|
|
The IOT-GATE-iMX8 board has an Intel Wifi 6 AX200 module.
Enable the IWLWIFI driver so that Wifi can work by default.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add clock generator node to device tree for SG2042, and enable clock for
uart.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
|
|
Add compatible strings for the Arm Cortex-A725 and Cortex-A925 CPUs, as
well as new Neoverse cores: Arm Neoverse N3, Neoverse V2, Neoverse V3,
and Neoverse V3AE.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240618160450.3168005-1-andre.przywara@arm.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
The SC8180X platform has a PDC block, add a compatible for this.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240525-sc8180x-pdc-binding-compatible-v1-1-17031c85ed69@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
PCI devices and bridges DT nodes created during the PCI scan are created
with the interrupt-map property set to handle interrupts.
In order to set this interrupt-map property at a specific level, a
phandle to the parent interrupt controller is needed. On systems that
are not fully described by a device-tree, the parent interrupt
controller may be unavailable (i.e. not described by the device-tree).
As mentioned in the [1], avoiding the use of the interrupt-map property
and considering a PCI device as an interrupt controller itself avoid the
use of a parent interrupt phandle.
In that case, the PCI device itself as an interrupt controller is
responsible for routing the interrupts described in the device-tree
world (DT overlay) to the PCI interrupts.
Add the 'interrupt-controller' property in the PCI device DT node.
[1]: https://lore.kernel.org/lkml/CAL_Jsq+je7+9ATR=B6jXHjEJHjn24vQFs4Tvi9=vhDeK9n42Aw@mail.gmail.com/
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20240527161450.326615-18-herve.codina@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Improve of_unittest_changeset_prop() to have a test case for the
newly introduced of_changeset_add_prop_bool().
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20240527161450.326615-17-herve.codina@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
APIs to add some properties in a changeset exist but nothing to add a DT
boolean property (i.e. a property without any values).
Fill this lack with of_changeset_add_prop_bool().
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20240527161450.326615-16-herve.codina@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
No test cases are present to test the of_changes_add_prop_*() function
family.
Add a new test to fill this lack.
Functions tested are:
- of_changes_add_prop_string()
- of_changes_add_prop_string_array()
- of_changeset_add_prop_u32()
- of_changeset_add_prop_u32_array()
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20240527161450.326615-15-herve.codina@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
The str_array parameter has no reason to be an un-const array.
Indeed, elements of the 'str_array' array are not changed by the code.
Constify the 'str_array' array parameter.
With this const qualifier added, the following construction is allowed:
static const char * const tab_str[] = { "string1", "string2" };
of_changeset_add_prop_string_array(..., tab_str, ARRAY_SIZE(tab_str));
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20240527161450.326615-14-herve.codina@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Document the GPI DMA Engine on the SDX75 Platform.
Signed-off-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240517100423.2006022-2-quic_rohiagar@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Convert txt bindings of ImgTec's PDC watchdog timer to dtschema to allow
for validation.
Signed-off-by: Shresth Prasad <shrestprasad7@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240527195811.7897-2-shresthprasad7@gmail.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Now all in-tree users have been updated with interrupt-names properties
according to commit 0076a37a426b6c85 ("dt-bindings: timer: renesas,tmu:
Document input capture interrupt"), make interrupt-names required.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/65fdd0425be0cc1bae9e6f7996aceaa5ad34e510.1716985947.git.geert+renesas@glider.be
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Some SoC like i.MX8MP or i.MX8QXP use a power-domain for this IP. Add
SoC-specific compatibles, which also requires a power-domain.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240528071141.92003-2-alexander.stein@ew.tq-group.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
The HX83100A is a bit of an outlier in the Himax HX831xxx series of
touch controllers as it requires reading touch events through the AHB
interface of the MCU rather than providing a dedicated FIFO address like
the other chips do.
This patch implements the specific read function and introduces the
HX83100A chip with an appropriate i2c ID and DT compatible string.
The HX83100A doesn't have a straightforward way to do chip
identification, which is why it is not implemented in this patch.
Tested on: Lenovo ThinkSmart View (CD-18781Y) / Innolux P080DDD-AB2 LCM
Signed-off-by: Felix Kaechele <felix@kaechele.ca>
Tested-by: Paul Gale <paul@siliconpixel.com>
Link: https://lore.kernel.org/r/20240620145019.156187-6-felix@kaechele.ca
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In preparation for HX83100A support allow defining separate functions
for specific chip operations.
Signed-off-by: Felix Kaechele <felix@kaechele.ca>
Link: https://lore.kernel.org/r/20240620145019.156187-5-felix@kaechele.ca
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Implement reading from the MCU in a more universal fashion. This allows
properly handling reads of more than 4 bytes using the AHB FIFO
implemented in the chip.
Signed-off-by: Felix Kaechele <felix@kaechele.ca>
Link: https://lore.kernel.org/r/20240620145019.156187-4-felix@kaechele.ca
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Himax uses an AHB-style bus to communicate with different parts of the
display driver and touch controller system.
Use more descriptive names for the register and address defines.
The names were taken from a driver submission for the similar HX83102J
chip.
Signed-off-by: Felix Kaechele <felix@kaechele.ca>
Link: https://lore.kernel.org/all/TY0PR06MB561105A3386E9D76F429110D9E0F2@TY0PR06MB5611.apcprd06.prod.outlook.com/
Link: https://lore.kernel.org/r/20240620145019.156187-3-felix@kaechele.ca
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add a compatible string for the Himax HX83100A touch controller.
The HX83100A presents touch events on the internal bus rather than
offering a dedicated event register like the other chips in this family
do.
Signed-off-by: Felix Kaechele <felix@kaechele.ca>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240620145019.156187-2-felix@kaechele.ca
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Now that the input_dev->vals array is always there we can be assured
that input_pass_values() is always called with a non-0 number of
events. Remove the check.
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240703213756.3375978-8-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Preallocate memory for holding event values (input_dev->vals) so that
there is no need to check if it was allocated or not in the event
processing code.
The amount of memory will be adjusted after input device has been fully
set up upon registering device with the input core.
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240703213756.3375978-7-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In preparation to have dev->vals memory pre-allocated rearrange
code in input_alloc_device() so that it allows handling multiple
points of failure.
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240703213756.3375978-6-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Streamline event handling code by providing batch implementations for
filtering and event processing and using them in place of the main
event handler, as needed, instead of having complex branching logic
in the middle of the event processing code.
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240703213756.3375978-5-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In preparation to consolidating filtering and event processing in the
input core change events() method to return number of events processed
by it.
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240703213756.3375978-4-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Input core expects input handlers to be either filters, or regular
handlers, but not both. Additionally, for regular handlers it does
not make sense to define both single event method and batch method.
Refuse registering handler if it defines more than one method.
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240703213756.3375978-3-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Input core favors ->events() (batch) method over ->event() method
if the former is defined, so there is no point in defining evdev_event()
as it is never called. Remove it.
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20240703213756.3375978-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Imagis IST3038 is another variant of Imagis IST3038 IC, which has
a different register interface from IST3038C (possibly firmware defined).
Unlike IST3038C/IST3032C, IST3038 has different registers for commands,
which means IST3038 doesn't use protocol B.
Similar to IST3032C and maybe the other variants, IST3038 has touch keys
support, which provides KEY_APPSELECT and KEY_BACK.
Add support for IST3038 with touch keys.
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Link: https://lore.kernel.org/r/20240613025631.5425-4-raymondhackley@protonmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Imagis IST3038 is a variant of Imagis touchscreen IC. Document it in
imagis,ist3038c bindings.
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240613025631.5425-3-raymondhackley@protonmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
protocol_b is a property, which tells Imagis panel to use a different
format for coordinates.
IST30XXC series is known for using protocol B, while the other series
aren't. Note this could be confusing, unlike the model name implies.
Adjust the usage of protocol_b to avoid confusion.
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Link: https://lore.kernel.org/r/20240613025631.5425-2-raymondhackley@protonmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When probing, the hardware is not brought into a known state. This may
be a problem when a hypervisor restarts Linux without resetting the
hardware, leaving an old state running. Make sure the hardware gets
initialized, especially interrupts should be cleared and disabled.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Closes: https://lore.kernel.org/r/20240702045535.2000393-1-dirk.behme@de.bosch.com
Fixes: 6ccbe607132b ("i2c: add Renesas R-Car I2C driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Introduce i2c support to Airoha EN7581 SoC through the i2c-mt7621
driver.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Ray Liu <ray.liu@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
`bt1_i2c_cfg` is not modified and can be declared as const to
move its data to a read-only section.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
xiic_start_xfer can fail for different reasons:
- EBUSY: bus is busy or i2c messages still in tx_msg or rx_msg
- ETIMEDOUT: timed-out trying to clear the RX fifo
- EINVAL: wrong clock settings
Both EINVAL and ETIMEDOUT will currently print a specific error
message followed by a generic one, for example:
Failed to clear rx fifo
Error xiic_start_xfer
however EBUSY will simply output the generic message:
Error xiic_start_xfer
which is not really helpful.
This commit adds a new error message when a busy condition is detected
and also removes the generic message since it does not provide any
relevant information to the user.
Signed-off-by: Marc Ferland <marc.ferland@sonatest.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Convert the NXP I2C controller for LPC2xxx/178x/18xx/43xx
to newer DT schema. Created DT schema based on the .txt file
which had `compatible`, `reg`, `interrupts`, `clocks`,
`#address-cells` and `#size-cells` as required properties.
Additional changes to the original .txt binding
- added maintainer from the MAINTAINERS file.
- added resets property required by the corresponding DTS files.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kanak Shilledar <kanakshilledar@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Bindings coding style expects 2- or 4-space indentation in the DTS
example. Correct files having something odd (6- or 8-space) to 4-space
while re-ordering few properties according to DTS coding style (the
first property should be compatible, then reg/ranges). No functional
impact.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Reference the core I2C controller schema to properly define common
properties. This allows to drop several (now redundant) properties.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The reference i2c-controller.yaml already defines 'address-cells' and
'size-cells', so drop them from list of properties.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The reference i2c-controller.yaml already defines 'address-cells' and
'size-cells', so drop them from list of properties.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The reference i2c-controller.yaml already defines 'address-cells' and
'size-cells', so drop them from list of properties. Drop them as well
from required properties, even though i2c-controller.yaml does not
require them, because I2C controller could be enabled without any
children in DTS for user-space usage.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
A device may need the controller up during suspend_noirq() or
resume_noirq().
But if the controller is autosuspended, there is no way to wakeup it during
suspend_noirq() or resume_noirq() because runtime pm is disabled at this
time.
The suspend() callback wakes up the controller, so it is available until
its suspend_noirq() callback (pm_runtime_force_suspend()).
During the resume, it's restored by resume_noirq() callback
(pm_runtime_force_resume()). Then resume() callback enables autosuspend.
So the controller is up during a little time slot in suspend and resume
sequences even if it's not used.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Replace SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS() by
NOIRQ_SYSTEM_SLEEP_PM_OPS() and RUNTIME_PM_OPS().
The usage of pm_ptr() and these more recent macros allows the compiler to
see and drop the dead code.
The unnecessary '__maybe_unused' annotations on PM functions can be
removed.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
