summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-10-09drm/amd/pp: Refine smu7/8 request_smu_load_fw callback functionRex Zhu
The request_smu_load_fw of VI is used to load gfx/sdma ip's firmware. Check whether the gfx/sdma firmware have been loaded successfully in this callback function. if failed, driver can exit to avoid gpu hard hung. if successful, clean the flag reload_fw to avoid duplicated fw load. when suspend/resume, driver need to reload fw. so in suspend, reset the reload_fw flag to true to enable load fw when resume. Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/pp: Setup SoftRegsStart before request smu load fwRex Zhu
need to know SoftRegsStart value to visit the register UcodeLoadStatus to check fw loading state. Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/pp: Refine function iceland_start_smuRex Zhu
if upload firmware failed, no matter how many times the function runs again, the same error will be encountered. so remove the duplicated code. Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amdgpu: Move gfx flag in_suspend to adevRex Zhu
Move in_suspend flag to adev from gfx, so can be used in other ip blocks, also keep consistent with gpu_in_reset flag. Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/pp: Fix memory leak on CI/AIRex Zhu
On CI/AI, fw was not loaded by smu, but smu's fw still need to be released when driver fini. Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amdgpu: Drop dead define in amdgpu.hRex Zhu
the struct was not in use any more. Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amdgpu: Always enable fan sensors for readRex Zhu
don't need to set fan1_enable to read fan sensors. Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amdgpu: Disable sysfs pwm1 if not in manual fan controlRex Zhu
Following lm-sensors 3.0.0, Only enable pwm1 sysfs when fan control mode(pwm1_enable) in manual Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amdgpu: Add fan RPM setting via sysfsRex Zhu
Add fan1_target for get/set fan speed in RPM unit Add fan1_min/fan1_max for get min, max fan speed in RPM unit Add fan1_enable to enable/disable the fan1 sensor v3: drop the hardcode value of min/max rpm in comments pointed out by Alex. v2: query the min/max rpm gpu support instand of hardcode value. Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/pp: Implement AMDGPU_PP_SENSOR_MIN/MAX_FAN_RPMRex Zhu
so user can query the RPM range Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amdgpu: Add new AMDGPU_PP_SENSOR_MIN/MAX_FAN_RPM sensorRex Zhu
For getting the min/max fan speed in RPM units. Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amdgpu: Refine uvd_v6/7_0_enc_get_destroy_msgRex Zhu
1. make uvd_v7_0_enc_get_destroy_msg static 2. drop a function variable that always true Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: Signal hw_done() after waiting for flip_done()Shirish S
In amdgpu_dm_commit_tail(), wait until flip_done() is signaled before we signal hw_done(). [Why] This is to temporarily address a paging error that occurs when a nonblocking commit contends with another commit, particularly in a mirrored display configuration where at least 2 CRTCs are updated. The error occurs in drm_atomic_helper_wait_for_flip_done(), when we attempt to access the contents of new_crtc_state->commit. Here's the sequence for a mirrored 2 display setup (irrelevant steps left out for clarity): **THREAD 1** | **THREAD 2** | Initialize atomic state for flip | | Queue worker | ... | Do work for flip | | Signal hw_done() on CRTC 1 | Signal hw_done() on CRTC 2 | | Wait for flip_done() on CRTC 1 <---- **PREEMPTED BY THREAD 1** Initialize atomic state for cursor | update (1) | | Do cursor update work on both CRTCs | | Clear atomic state (2) | **DONE** | ... | | Wait for flip_done() on CRTC 2 | *ERROR* | The issue starts with (1). When the atomic state is initialized, the current CRTC states are duplicated to be the new_crtc_states, and referenced to be the old_crtc_states. (The new_crtc_states are to be filled with update data.) Some things to note: * Due to the mirrored configuration, the cursor updates on both CRTCs. * At this point, the pflip IRQ has already been handled, and flip_done signaled on all CRTCs. The cursor commit can therefore continue. * The old_crtc_states used by the cursor update are the **same states** as the new_crtc_states used by the flip worker. At (2), the old_crtc_state is freed (*), and the cursor commit completes. We then context switch back to the flip worker, where we attempt to access the new_crtc_state->commit object. This is problematic, as this state has already been freed. (*) Technically, 'state->crtcs[i].state' is freed, which was made to reference old_crtc_state in drm_atomic_helper_swap_state() [How] By moving hw_done() after wait_for_flip_done(), we're guaranteed that the new_crtc_state (from the flip worker's perspective) still exists. This is because any other commit will be blocked, waiting for the hw_done() signal. Note that both the i915 and imx drivers have this sequence flipped already, masking this problem. Signed-off-by: Shirish S <shirish.s@amd.com> Signed-off-by: Leo Li <sunpeng.li@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: Use proper enums in process_channel_replyNathan Chancellor
Clang warns when one enumerated type is implicitly converted to another. drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:315:19: warning: implicit conversion from enumeration type 'enum aux_channel_operation_result' to different enumeration type 'enum aux_transaction_reply' [-Wenum-conversion] reply->status = AUX_CHANNEL_OPERATION_FAILED_HPD_DISCON; ~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/i2caux/dce110/aux_engine_dce110.c:349:19: warning: implicit conversion from enumeration type 'enum aux_channel_operation_result' to different enumeration type 'enum aux_transaction_reply' [-Wenum-conversion] reply->status = AUX_CHANNEL_OPERATION_FAILED_HPD_DISCON; ~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ The current enum is incorrect, it should be from aux_transaction_reply, so use AUX_TRANSACTION_REPLY_HPD_DISCON. Reported-by: Nick Desaulniers <ndesaulniers@google.com> Suggested-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: Raise dispclk value for dce_update_clocksNicholas Kazlauskas
[Why] The DISPCLK value was previously requested to be 15% higher for all ASICS that went through the dce110 bandwidth code path. As part of a refactoring of dce_clocks and dce110 set_bandwidth this was removed for power saving considerations. This changed caused corruption under certain display configurations. Originally thought to be Vega specific, it was also observed on Polaris. [How] The 15% is brought back but its placement differs from the original patch. This boost should only be enable while DFS bypass is inactive. This (like the Vega patch) is also a workaround that should be removed after the root cause is identified. Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: HLK Periodic Frame Notification test failedMurton Liu
[Why] Due to a small pre-fetch window, the active vline timing is a couple of lines off when compared to what it should be. [How] Changed the calculation for the start vline to account for this window. Signed-off-by: Murton Liu <murton.liu@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: fix Interlace video timing.Charlene Liu
[Description] interlace mode shows wrong vertical timing. Interface timing in Edid is half vertical timing as progressive timing. driver doubled the vertical timing in edid_paser, no need to double in optc again. Signed-off-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Chris Park <Chris.Park@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: Flatten irq handler data structLeo Li
[Why] There is no reason why the common data needs to be kept separate. [How] Flatten the struct by moving common data into the DM IRQ struct. Signed-off-by: Leo Li <sunpeng.li@amd.com> Reviewed-by: David Francis <David.Francis@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: fix memory leak in resource poolsJun Lei
[why] ddc engines were recently changed to be independently tracked from pipe count. the change was reflected in resource constructor but not in destructor. this manifests as a memory leak when pipe harvesting is enabled, since not all constructed ddc engines are freed [how] make destructor symmetric with constructor for all dcX_resource Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: dc 3.1.68Tony Cheng
Signed-off-by: Tony Cheng <tony.cheng@amd.com> Reviewed-by: Steven Chiu <Steven.Chiu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: WA for DF keeps awake after S0i3.Yongqiang Sun
[Why] DF keeps awake after S0i3 resume due to DRAM_STATE_CNTL is set by bios command table during dcn init_hw. [How] As a work around, check STATE_CNTL status before init_hw, if it is 0 before init_hw and set to 1 after init_hw, change it to 0. Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: clean up encoding checksEric Yang
[Why] All ASICS we support has YCbCr support, so the check is unnecessary, the currently logic in validate output also returns true all the time, so the unneccessary logic is removed Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: block DP YCbCr420 modesEric Yang
[why] Currently not supported, will black screen when set. [How] Fail validate timing helper for those modes. Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: Add function to fetch clock requirementsEryk Brol
Also add dram clock to clocks struct, for systems that uses them. Signed-off-by: Eryk Brol <eryk.brol@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: Calculate swizzle mode using bpp during validationSu Sung Chung
[Why] Previously bandwidth validation was failing because swizzle mode was not initialized during plane_state allocation. The swizzle mode was calculated using pixed format which is how swizzle mode is initially calculated in addrlib. [How] * Set default swizzle mode for validation to DC_SW_UNKNOWN * Created new function in dcn10_assign_swizzle_mode which sets the plane swizzle mode based on selected pixed format * Added the call of assign_swizzle_mode into dc_validate_global_state * Set failsafe swizzle mode back to DC_SW_LINEAR Signed-off-by: Su Sung Chung <Su.Chung@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: Add a check-function for virtual signal typeNikola Cornij
[why] Same functions exist for all other signal types. [how] Add a function that checks against virtual signal type. Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: fix 4K stereo screen flash issueCharlene Liu
[Why] HDMI_scramber is not enabled for pixel rate >340Mhz. [How] Calculate the phy clock to include the Hw frame packing factor. Signed-off-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Chris Park <Chris.Park@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/display: Add DC build_id to determine build typeJun Lei
[why] Sometimes there are indications that the incorrect driver is being loaded in automated tests. This change adds the ability for builds to be tagged with a string, and picked up by the test infrastructure. [how] dc.c will allocate const for build id, which is init-ed with default value, indicating production build. For test builds, build server will find/replace this value. The test machine will then verify this value. Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/powerplay: Enable/Disable NBPSTATE on On/OFF of UVDAkshu Agrawal
We observe black lines (underflow) on display when playing a 4K video with UVD. On Disabling Low memory P state this issue is not seen. Multiple runs of power measurement shows no imapct. Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com> Signed-off-by: Satyajit Sahu <satyajit.sahu@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
2018-10-09drm/amd/pp: Remove wrong code in fiji_start_smuRex Zhu
HW CG feature will be enabled after hw ip initialized Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/pp: Remove uncessary extra vcn pg cntl in smuRex Zhu
the vcn power will be controlled by VCN. Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amdgpu: Move out power up/down sdma out of smuRex Zhu
smu only expose interface to other ip blocks. in order to reduce dependence between smu and other ip blocks Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/pp: Expose the smu support for SDMA PG cntlRex Zhu
SDMA IP can be power up/down via smu message Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/pp: Avoid divide-by-zero in fan_ctrl_set_fan_speed_rpmRex Zhu
The minRPM speed maybe equal to zero. so need to check input RPM not equal to 0, otherwise cause divide-by-zero driver crash. Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/pp: Fix fan's RPM setting not work on VI/Vega10Rex Zhu
set the target rpm value to wrong register. Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amdgpu: Fix comments error in sdma_v4_1_update_power_gatingRex Zhu
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/powerplay: enable MGPU fan boost feature on Vega20Evan Quan
Added Vega20 specific implementation for MGPU fan boost feature. Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/powerplay: helper interfaces for MGPU fan boost featureEvan Quan
MGPU fan boost feature is enabled only when two or more dGPUs in the system. Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amdgpu: added AMD GPU instance counting V2Evan Quan
Count all GPU instances from AMD(including iGPUs and dGPUs) in the system. V2: drop unnecessary initialization for other gpu_info members except mutex Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amdgpu/vega20: make power profile output more consistentAlex Deucher
Make the profile name line match previous generations more closely. E.g., 0 3D_FULL_SCREEN : vs: 0(3D_FULL_SCREEN ) Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amdgpu: change Raven always on CUs to 4Evan Quan
For Vega10 and Vega20, the always on CUs are 12. For Raven, it's 4. Signed-off-by: Evan Quan <evan.quan@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amdgpu: added vega20 LBPW support v2Evan Quan
Enable LBPW support on vega20. v2: squash in warning fix (Alex) Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/powerplay/vega20: enable fan RPM and pwm settings V2Evan Quan
Manual fan RPM and pwm setting on vega20 are available now. V2: correct the register for fan speed setting and avoid divide-by-zero Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/powerplay/vega20: tell the correct gfx voltage V2Evan Quan
Export the correct gfx voltage by hwmon interface. V2: update the register naming for consistency Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09drm/amd/powerplay/vega20: correct the hwmon interface ppt limit outputEvan Quan
The ppt limit read out by hwmon interface is always 0. Correct this hwmon interface output. Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2018-10-09MAINTAINERS: Add Maxime Ripard as drm-misc maintainerSean Paul
Unfortunately Gustavo has decided to step down as drm-misc maintainer to focus on other projects. Thanks Gustavo for your dedication and hard work! Fortunately for us, we have a wealth of people qualified to assume a -misc maintainer role. Maxime has done an outstanding job with sun4i and in the community in general. I'm really excited that he agreed to take on this responsibility and I look forward to working with him! Cc: Dave Airlie <airlied@linux.ie> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Acked-by: Dave Airlie <airlied@linux.ie> Signed-off-by: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20181005160256.200162-1-sean@poorly.run
2018-10-09drm/i915: add a common connector type independent destroy hookJani Nikula
Almost all of the connector destroy functions do the same thing. The differences are in the edid, detect_edid and panel cleanups, but those are safely NULL when not initialized. Roll out a common connector destroy hook. Inspired by commit bc3213c44415 ("drm/i915: Drop the eDP check from intel_dp_connector_destroy()"). Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181009141103.20387-1-jani.nikula@intel.com
2018-10-09drm/i915: Fix intel_dp_mst_best_encoder()Lyude Paul
Currently, i915 appears to rely on blocking modesets on no-longer-present MSTB ports by simply returning NULL for ->best_encoder(), which in turn causes any new atomic commits that don't disable the CRTC to fail. This is wrong however, since we still want to allow userspace to disable CRTCs on no-longer-present MSTB ports by changing the DPMS state to off and this still requires that we retrieve an encoder. So, fix this by always returning a valid encoder regardless of the state of the MST port. Changes since v1: - Remove mst atomic helper, since this got replaced with a much simpler solution Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20181008232437.5571-6-lyude@redhat.com
2018-10-09drm/i915: Skip vcpi allocation for MSTB ports that are goneLyude Paul
Since we need to be able to allow DPMS on->off prop changes after an MST port has disappeared from the system, we need to be able to make sure we can compute a config for the resulting atomic commit. Currently this is impossible when the port has disappeared, since the VCPI slot searching we try to do in intel_dp_mst_compute_config() will fail with -EINVAL. Since the only commits we want to allow on no-longer-present MST ports are ones that shut off display hardware, we already know that no VCPI allocations are needed. So, hardcode the VCPI slot count to 0 when intel_dp_mst_compute_config() is called on an MST port that's gone. Changes since V4: - Don't use mst_port_gone at all, just check whether or not the drm connector is registered - Daniel Vetter Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20181008232437.5571-5-lyude@redhat.com
2018-10-09drm/i915: Don't unset intel_connector->mst_portLyude Paul
Currently we set intel_connector->mst_port to NULL to signify that the MST port has been removed from the system so that we can prevent further action on the port such as connector probes, mode probing, etc. However, we're going to need access to intel_connector->mst_port in order to fixup ->best_encoder() so that it can always return the correct encoder for an MST port to prevent legacy DPMS prop changes from failing. This should be safe, so instead keep intel_connector->mst_port always set and instead just check the status of drm_connector->regustered to signify whether or not the connector has disappeared from the system. Changes since v2: - Add a comment to mst_port_gone (Jani Nikula) - Change mst_port_gone to a u8 instead of a bool, per the kernel bot. Apparently bool is discouraged in structs these days Changes since v4: - Don't use mst_port_gone at all! Just check if the connector is registered or not - Daniel Vetter Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20181008232437.5571-4-lyude@redhat.com
generated by cgit (git 2.34.1) at 2025-09-19 07:13:57 +0000