| Age | Commit message (Collapse) | Author |
|---|
|
Check budget fullness only after it's updated and update
channel mask only once to keep budget balance between channels.
It's also needed for farther changes.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows to rate limit queues tx queues for cpsw interface.
The rate is set in absolute Mb/s units and cannot be more a speed
an interface is connected with.
The rate for a tx queue can be tested with:
ethtool -L eth0 rx 4 tx 4
echo 100 > /sys/class/net/eth0/queues/tx-0/tx_maxrate
echo 200 > /sys/class/net/eth0/queues/tx-1/tx_maxrate
echo 50 > /sys/class/net/eth0/queues/tx-2/tx_maxrate
echo 30 > /sys/class/net/eth0/queues/tx-3/tx_maxrate
tc qdisc add dev eth0 root handle 1: multiq
tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5001 0xffff action skbedit queue_mapping 0
tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5002 0xffff action skbedit queue_mapping 1
tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5003 0xffff action skbedit queue_mapping 2
tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5004 0xffff action skbedit queue_mapping 3
iperf -c 192.168.2.1 -b 110M -p 5001 -f m -t 60
iperf -c 192.168.2.1 -b 215M -p 5002 -f m -t 60
iperf -c 192.168.2.1 -b 55M -p 5003 -f m -t 60
iperf -c 192.168.2.1 -b 32M -p 5004 -f m -t 60
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpdma has 8 rate limited tx channels. This patch adds
ability for cpdma driver to use 8 tx h/w shapers. If at least one
channel is not rate limited then it must have higher number, this
is because the rate limited channels have to have higher priority
then not rate limited channels. The channel priority is set in low-hi
direction already, so that when a new channel is added with ethtool
and it doesn't have rate yet, it cannot affect on rate limited
channels. It can be useful for TSN streams and just in cases when
h/w rate limited channels are needed.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The weight of a channel is needed to split descriptors between
channels. The weight can depend on maximum rate of channels, maximum
rate of an interface or other reasons. The channel weight is in
percentage and is independent for rx and tx channels.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.9
mwifiex
* properly terminate SSIDs so that uninitalised memory is not printed
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Yuval Mintz says:
====================
qed*: Add XDP support
This patch series is intended to add XDP to the qede driver, although
it contains quite a bit of cleanups, refactorings and infrastructure
changes as well.
The content of this series can be roughly divided into:
- Datapath improvements - mostly focused on having the datapath utilize
parameters which can be more tightly contained in cachelines.
Patches #1, #2, #8, #9 belong to this group.
- Refactoring - done mostly in favour of XDP. Patches #3, #4, #5, #9.
- Infrastructure changes - done in favour of XDP. Paches #6 and #7 belong
to this category [#7 being by far the biggest patch in the series].
- Actual XDP support - last two patches [#10, #11].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for forwarding via XDP. Once the eBPF is attached,
driver would allocate & configure a designated transmission queue
meant solely for forwarding packets. Said queue would share the
receive-queue's interrupt line, and would have it's own Tx statistics.
Infrastructure changes required for this [spread-out through the code]:
- Determine the DMA direction of the receive buffers based on the presence
of the eBPF program.
- Turn the sw Tx ring into a union, as regular/XDP queues have different
needs for releasing resources after completion [regular requires the SKB,
XDP requires the transmitted page].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the ndo_xdp callback. This patch would support XDP_PASS,
XDP_DROP and XDP_ABORTED commands.
This also adds a per Rx queue statistic which counts number of packets
which didn't reach the stack [due to XDP].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Improve the cacheline usage of both queues by reordering -
This reduces the cachelines required for egress datapath processing
from 3 to 2 and those required by ingress datapath processing by 2.
It also changes a couple of datapath related functions that currently
require either the fastpath or the qede_dev, changing them to be based
on the tx/rx queue instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Receive-hashing is a fixed feature, so there's no need to check
during the ingress datapath whether it's set or not.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver needs to maintain several FW/HW-indices for each one of
its queues. Currently, that mapping is done by the QED where it uses
an rx/tx array of so-called hw-cids, populating them whenever a new
queue is opened and clearing them upon destruction of said queues.
This maintenance is far from ideal - there's no real reason why
QED needs to maintain such a data-structure. It becomes even worse
when considering the fact that the PF's queues and its child VFs' queues
are all mapped into the same data-structure.
As a by-product, the set of parameters an interface needs to supply for
queue APIs is non-trivial, and some of the variables in the API
structures have different meaning depending on their exact place
in the configuration flow.
This patch re-organizes the way L2 queues are configured and maintained.
In short:
- Required parameters for queue init are now well-defined.
- Qed would allocate a queue-cid based on parameters.
Upon initialization success, it would return a handle to caller.
- Queue-handle would be maintained by entity requesting queue-init,
not necessarily qed.
- All further queue-APIs [update, destroy] would use the opaque
handle as reference for the queue instead of various indices.
The possible owners of such handles:
- PF queues [qede] - complete handles based on provided configuration.
- VF queues [qede] - fw-context-less handles, containing only relative
information; Only the PF-side would need the absolute indices
for configuration, so they're omitted here.
- VF queues [qed, PF-side] - complete handles based on VF initialization.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As qede utilizes an internal-reload sequence as result of various
configuration changes, the netif state wouldn't always accurately describe
the status of the configuration.
To compensate, we're storing an internal state of the device, which should
only be accessed under the qede_lock.
This patch fixes and improves several state/lock interactions:
- The internal state should only be checked while locked.
- While holding lock, it's preferable to check state rather than
the netdevice's state.
- The reload sequence is not 'atomic' - unload and subsequent load
are not in the same critical section.
This also add the 'locked' variant for the reload, which would later be
used by XDP - useful in the case where the correct sequence is 'lock,
check state and re-configure if good', instead of allowing the reload
itself to make the decision regarding the configurability of the device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver's NAPI poll is using a long sequence for processing ingress
packets, and it's going to get even longer once we do XDP.
Break down the main loop into a series of sub-functions to allow
better readability of the function.
While we're at it, correct the accounting of the NAPI budget -
currently we're counting only packets passed to the stack against
the budget, even in case those are actually aggregations.
After refactoring every CQE processed would be counted against the budget.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor logic for gathering statistics into a per-queue function.
This improves readability of the driver statistics' flows.
In addition, this would be required by the XDP forwarding queues
[as we'll need the Txq statistics gathering methods for those as well].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver currently doesn't support multi-CoS, but it contains logic
where multiple transmission queues could be theoretically manipulated.
No point in maintaining the infrastructure at the moment.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The chain structure and functions are widely used by the qed* modules,
both for configuration and datapath.
E.g., qede's Tx has one such chain and its Rx has two.
Currently, the strucutre's fields which are required for datapath
related functions [produce/consume] are intertwined with fields which
are required only for configuration purposes [init/destroy/etc.].
This patch re-arranges the chain structure so that all the fields which
are required for datapath usage could reside in a single cacheline instead
of the two which are required today.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver needs to maintain a structure per-each concurrent possible
open aggregation, but the structure storing that metadata is far from
being optimized - biggest waste in it is that there are 2 buffer metadata,
one for a replacement buffer when the aggregation begins and the other for
holding the first aggregation's buffer after it begins [as firmware might
still update it]. Those 2 can safely be united into a single metadata
structure.
struct qede_agg_info changes the following:
/* size: 120, cachelines: 2, members: 9 */
/* sum members: 114, holes: 1, sum holes: 4 */
/* padding: 2 */
/* paddings: 2, sum paddings: 8 */
/* last cacheline: 56 bytes */
-->
/* size: 48, cachelines: 1, members: 9 */
/* paddings: 1, sum paddings: 4 */
/* last cacheline: 48 bytes */
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The memory for netdev private data is allocated using kzalloc/vzalloc in
alloc_netdev_mqs, thus there is no need to zero the stats portion of it
again in the driver's probe function.
In any case, the size for the memset is wrong as the stats member is of
type rtnl_link_stats64, not net_device_stats.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Guillaume Nault says:
====================
l2tp: fixes for l2tp_ip and l2tp_ip6 socket handling
This series addresses problems found while working on commit 32c231164b76
("l2tp: fix racy SOCK_ZAPPED flag check in l2tp_ip{,6}_bind()").
The first three patches fix races in socket's connect, recv and bind
operations. The last two ones fix scenarios where l2tp fails to
correctly lookup its userspace sockets.
Apart from the last patch, which is l2tp_ip6 specific, every patch
fixes the same problem in the L2TP IPv4 and IPv6 code.
All problems fixed by this series exist since the creation of the
l2tp_ip and l2tp_ip6 modules.
Changes since v1:
* Patch #3: fix possible uninitialised use of 'ret' in l2tp_ip_bind().
====================
Acked-by: James Chapman <jchapman@katalix.com>
|
|
The '!(addr && ipv6_addr_equal(addr, laddr))' part of the conditional
matches if addr is NULL or if addr != laddr.
But the intend of __l2tp_ip6_bind_lookup() is to find a sockets with
the same address, so the ipv6_addr_equal() condition needs to be
inverted.
For better clarity and consistency with the rest of the expression, the
(!X || X == Y) notation is used instead of !(X && X != Y).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When looking up an l2tp socket, we must consider a null netdevice id as
wild card. There are currently two problems caused by
__l2tp_ip_bind_lookup() not considering 'dif' as wild card when set to 0:
* A socket bound to a device (i.e. with sk->sk_bound_dev_if != 0)
never receives any packet. Since __l2tp_ip_bind_lookup() is called
with dif == 0 in l2tp_ip_recv(), sk->sk_bound_dev_if is always
different from 'dif' so the socket doesn't match.
* Two sockets, one bound to a device but not the other, can be bound
to the same address. If the first socket binding to the address is
the one that is also bound to a device, the second socket can bind
to the same address without __l2tp_ip_bind_lookup() noticing the
overlap.
To fix this issue, we need to consider that any null device index, be
it 'sk->sk_bound_dev_if' or 'dif', matches with any other value.
We also need to pass the input device index to __l2tp_ip_bind_lookup()
on reception so that sockets bound to a device never receive packets
from other devices.
This patch fixes l2tp_ip6 in the same way.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's not enough to check for sockets bound to same address at the
beginning of l2tp_ip{,6}_bind(): even if no socket is found at that
time, a socket with the same address could be bound before we take
the l2tp lock again.
This patch moves the lookup right before inserting the new socket, so
that no change can ever happen to the list between address lookup and
socket insertion.
Care is taken to avoid side effects on the socket in case of failure.
That is, modifications of the socket are done after the lookup, when
binding is guaranteed to succeed, and before releasing the l2tp lock,
so that concurrent lookups will always see fully initialised sockets.
For l2tp_ip, 'ret' is set to -EINVAL before checking the SOCK_ZAPPED
bit. Error code was mistakenly set to -EADDRINUSE on error by commit
32c231164b76 ("l2tp: fix racy SOCK_ZAPPED flag check in l2tp_ip{,6}_bind()").
Using -EINVAL restores original behaviour.
For l2tp_ip6, the lookup is now always done with the correct bound
device. Before this patch, when binding to a link-local address, the
lookup was done with the original sk->sk_bound_dev_if, which was later
overwritten with addr->l2tp_scope_id. Lookup is now performed with the
final sk->sk_bound_dev_if value.
Finally, the (addr_len >= sizeof(struct sockaddr_in6)) check has been
dropped: addr is a sockaddr_l2tpip6 not sockaddr_in6 and addr_len has
already been checked at this point (this part of the code seems to have
been copy-pasted from net/ipv6/raw.c).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Socket must be held while under the protection of the l2tp lock; there
is no guarantee that sk remains valid after the read_unlock_bh() call.
Same issue for l2tp_ip and l2tp_ip6.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Socket flags aren't updated atomically, so the socket must be locked
while reading the SOCK_ZAPPED flag.
This issue exists for both l2tp_ip and l2tp_ip6. For IPv6, this patch
also brings error handling for __ip6_datagram_connect() failures.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
this #include is unnecessary and brings whole set of
other headers into cgroup-defs.h. Remove it.
Fixes: 3007098494be ("cgroup: add support for eBPF programs")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Rami Rosen <roszenrami@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently loop index 'idx' is used as the index in the neigh list of interest.
It's increased only when the neigh is dumped. It's not the absolute index in
the list. Because there is no info to record which neigh has already be scanned
by previous loop. This will cause the filtered out neighs to be scanned mulitple
times.
This patch make idx as the absolute index in the list, it will increase no matter
whether the neigh is filtered. This will prevent the above problem.
And this is in line with other dump functions.
v2:
- take David Ahern's advice to do simple change
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ER records are printed without explicit log level presuming line
continuation until "\n". After the commit 4bcc595ccd8 (printk:
reinstate KERN_CONT for printing continuation lines), the ER records are
printed a character per line.
Adding KERN_CONT to appropriate printk statements restores the printout
behavior.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Execution 'ethtool -S' on fec device that is down causes OOPS on Vybrid
board:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xe0898200
pgd = ddecc000
[e0898200] *pgd=9e406811, *pte=400d1653, *ppte=400d1453
Internal error: : 1008 [#1] SMP ARM
...
Reason of OOPS is that fec_enet_get_ethtool_stats() accesses fec
registers while IPG clock is stopped by PM.
Fix that by caching statistics in fec_enet_private. Cache is initialized
at device probe time, and updated at statistics request time if device
is up, and also just before turning device off on down path.
Additional locking is not needed, since cached statistics is accessed
either before device is registered, or under rtnl_lock().
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following build error:
HOSTCC samples/bpf/test_lru_dist.o
../samples/bpf/test_lru_dist.c:25:22: fatal error: bpf_util.h: No such file or directory
This is due to objtree != srctree.
Use srctree, since that's where bpf_util.h is located.
Fixes: e00c7b216f34 ("bpf: fix multiple issues in selftest suite and samples")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch replaces printk() with netdev_err() for macvtap device.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vxlan_fdb_append may return error, so add the proper check,
otherwise it will cause memory leak.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Changes in v2:
- Unnecessary to initialize rc to zero.
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
0x275 is used by KEY_FASTREVERSE.
Fixes: 488326947cd1 ("Input: add HDMI CEC specific keycodes")
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Raghu Vatsavayi says:
====================
liquidio VF operations
This patchseries adds support for VF device specific operations
like mailbox, queues and register access. This V3 patchset also
has changes based on comments form earlier versions:
1) Removed extra 'void *' casting.
2) Fixed all cross compilations issues reported on S390 and Powerpc
architectures.
Please apply the patches in following order as these patches depend
on each other.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for VF initialization and destroy resources.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for VF interrupt processing.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for VF mailbox setup.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for initializing softcommand, dispatch and
instructions queues for VF.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for VF device register access.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for configuring VF input/output queues.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for setting up VF configuration.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for cn23xx VF probe and registration.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for CN23xx VF registers.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If nf_ct_frag6_gather() returns an error other than -EINPROGRESS, it
means that we still have a reference to the skb. We should free it
before returning from handle_fragments, as stated in the comment above.
Fixes: daaa7d647f81 ("netfilter: ipv6: avoid nf_iterate recursion")
CC: Florian Westphal <fw@strlen.de>
CC: Pravin B Shelar <pshelar@ovn.org>
CC: Joe Stringer <joe@ovn.org>
Signed-off-by: Daniele Di Proietto <diproiettod@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch modifies test_cgrp2_attach to use getopt so we can use standard
command line parsing.
It also adds an option to run the program in detach only mode. This does
not attach a new filter at the cgroup, but only runs the detach command.
Lastly, it changes the attach code to not detach and then attach. It relies
on the 'hotswap' behaviour of CGroup BPF programs to be able to change
in-place. If detach-then-attach behaviour needs to be tested, the example
can be run in detach only mode prior to attachment.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Rasesh Mody <Rasesh.Mody@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an IFLA_XDP_FLAGS attribute that can be passed for setting up
XDP along with IFLA_XDP_FD, which eventually allows user space to
implement typical add/replace/delete logic for programs. Right now,
calling into dev_change_xdp_fd() will always replace previous programs.
When passed XDP_FLAGS_UPDATE_IF_NOEXIST, we can handle this more
graceful when requested by returning -EBUSY in case we try to
attach a new program, but we find that another one is already
attached. This will be used by upcoming front-end for iproute2 as
well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Fainelli says:
====================
net: phy: broadcom: Support for PHY counters
This patch series adds support for reading the Broadcom PHYs internal counters.
Changes in v3:
- fixed the allocation of priv->stats in bcm7xxx
Changes in v2:
- fixed modular build reported by kbuild
- constify array of stats
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Broadcom BCM7xxx internal PHYs can leverage the Broadcom PHY library
module PHY error counters helper functions, just implement the
appropriate PHY driver function calls to do so. We need to allocate some
storage space for our PHY statistics, and provide it to the Broadcom PHY
library, so do this in a specific probe function, and slightly wrap the
get_stats function call.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Broadcom PHYs expose a number of PHY error counters: receive errors,
false carrier sense, SerDes BER count, local and remote receive errors.
Add support code to allow retrieving these error counters. Since the
Broadcom PHY library code is used by several drivers, make it possible
for them to specify the storage for the software copy of the statistics.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
