| Age | Commit message (Collapse) | Author |
|---|
|
The MDIO controller has support to release the internal PHYs from reset
by specifying a second memory resource. This is different between the
currently supported SparX-5 and the LAN966x. Add a new compatible to
distinguish between these two.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
DSA probing is atypical because a tree of devices must probe all at
once, so out of N switches which call dsa_tree_setup_routing_table()
during probe, for (N - 1) of them, "complete" will return false and they
will exit probing early. The Nth switch will set up the whole tree on
their behalf.
The implication is that for (N - 1) switches, the driver binds to the
device successfully, without doing anything. When the driver is bound,
the ->shutdown() method may run. But if the Nth switch has failed to
initialize the tree, there is nothing to do for the (N - 1) driver
instances, since the slave devices have not been created, etc. Moreover,
dsa_switch_shutdown() expects that the calling @ds has been in fact
initialized, so it jumps at dereferencing the various data structures,
which is incorrect.
Avoid the ensuing NULL pointer dereferences by simply checking whether
the Nth switch has previously set "ds->setup = true" for the switch
which is currently shutting down. The entire setup is serialized under
dsa2_mutex which we already hold.
Fixes: 0650bf52b31f ("net: dsa: be compatible with masters which unregister on shutdown")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220318195443.275026-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During NAT, a tuple collision may occur. When this happens, openvswitch
will make a second pass through NAT which will perform additional packet
modification. This will update the skb data, but not the flow key that
OVS uses. This means that future flow lookups, and packet matches will
have incorrect data. This has been supported since
5d50aa83e2c8 ("openvswitch: support asymmetric conntrack").
That commit failed to properly update the sw_flow_key attributes, since
it only called the ovs_ct_nat_update_key once, rather than each time
ovs_ct_nat_execute was called. As these two operations are linked, the
ovs_ct_nat_execute() function should always make sure that the
sw_flow_key is updated after a successful call through NAT infrastructure.
Fixes: 5d50aa83e2c8 ("openvswitch: support asymmetric conntrack")
Cc: Dumitru Ceara <dceara@redhat.com>
Cc: Numan Siddique <nusiddiq@redhat.com>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20220318124319.3056455-1-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit update from Paul Moore:
"Just one audit patch queued for v5.18:
- Change the AUDIT_TIME_* record generation so that they are
generated at syscall exit time and subject to all of the normal
syscall exit filtering.
This should help reduce noise and ensure those records which are
most relevant to the admin's audit configuration are recorded in
the audit log"
* tag 'audit-pr-20220321' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: log AUDIT_TIME_* records only from rules
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux updates from Paul Moore:
"We've got a number of SELinux patches queued up, the highlights are:
- Fixup the security_fs_context_parse_param() LSM hook so it executes
all of the LSM hook implementations unless a serious error occurs.
We also correct the SELinux hook implementation so that it returns
zero on success.
- In addition to a few SELinux mount option parsing fixes, we
simplified the parsing by moving it earlier in the process.
The logic was that it was unlikely an admin/user would use the new
mount API and not have the policy loaded before passing the SELinux
options.
- Properly fixed the LSM/SELinux/SCTP hooks with the addition of the
security_sctp_assoc_established() hook.
This work was done in conjunction with the netdev folks and should
complete the move of the SCTP labeling from the endpoints to the
associations.
- Fixed a variety of sparse warnings caused by changes in the "__rcu"
markings of some core kernel structures.
- Ensure we access the superblock's LSM security blob using the
stacking-safe accessors.
- Added the ability for the kernel to always allow FIOCLEX and
FIONCLEX if the "ioctl_skip_cloexec" policy capability is
specified.
- Various constifications improvements, type casting improvements,
additional return value checks, and dead code/parameter removal.
- Documentation fixes"
* tag 'selinux-pr-20220321' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux: (23 commits)
selinux: shorten the policy capability enum names
docs: fix 'make htmldocs' warning in SCTP.rst
selinux: allow FIOCLEX and FIONCLEX with policy capability
selinux: use correct type for context length
selinux: drop return statement at end of void functions
security: implement sctp_assoc_established hook in selinux
security: add sctp_assoc_established hook
selinux: parse contexts for mount options early
selinux: various sparse fixes
selinux: try to use preparsed sid before calling parse_sid()
selinux: Fix selinux_sb_mnt_opts_compat()
LSM: general protection fault in legacy_parse_param
selinux: fix a type cast problem in cred_init_security()
selinux: drop unused macro
selinux: simplify cred_init_security
selinux: do not discard const qualifier in cast
selinux: drop unused parameter of avtab_insert_node
selinux: drop cast to same type
selinux: enclose macro arguments in parenthesis
selinux: declare name parameter of hash_eval const
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity
Pull integrity subsystem updates from Mimi Zohar:
"Except for extending the 'encrypted' key type to support user provided
data, the rest is code cleanup, __setup() usage bug fix, and a trivial
change"
* tag 'integrity-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
MAINTAINERS: add missing security/integrity/platform_certs
EVM: fix the evm= __setup handler return value
KEYS: encrypted: Instantiate key with user-provided decrypted data
ima: define ima_max_digest_data struct without a flexible array variable
ima: rename IMA_ACTION_FLAGS to IMA_NONACTION_FLAGS
ima: Return error code obtained from securityfs functions
MAINTAINERS: add missing "security/integrity" directory
ima: Fix trivial typos in the comments
|
|
Pull smack update from Casey Schaufler:
"A single fix to repair an incorrect use of ntohs() in IPv6 audit code.
It's very minor and went unnoticed until lkp found it.
It's been in next and passes all tests"
* tag 'Smack-for-5.18' of https://github.com/cschaufler/smack-next:
Fix incorrect type in assignment of ipv6 port for audit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull watch_queue fixes from David Howells:
"Here are fixes for a couple more watch_queue bugs, both found by syzbot:
- Fix error cleanup in watch_queue_set_size() where it tries to clean
up all the pointers in the page list, even if they've not been
allocated yet[1]. Unfortunately, __free_page() doesn't treat a NULL
pointer as being "do nothing".
A second report[2] looks like it's probably the same bug, but on
arm64 rather than x86_64, but there's no reproducer.
- Fix a missing kfree in free_watch() to actually free the watch[3]"
Link: https://lore.kernel.org/r/000000000000b1807c05daad8f98@google.com/ [1]
Link: https://lore.kernel.org/r/000000000000035b9c05daae8a5e@google.com/ [2]
Link: https://lore.kernel.org/r/000000000000bc8eaf05dab91c63@google.com/ [3]
* 'keys-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
watch_queue: Actually free the watch
watch_queue: Fix NULL dereference in error cleanup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull bounds fixes from Kees Cook:
"These are a handful of buffer and array bounds fixes that I've been
carrying in preparation for the coming memcpy improvements and the
enabling of '-Warray-bounds' globally.
There are additional similar fixes in other maintainer's trees, but
these ended up getting carried by me. :)"
* tag 'bounds-fixes-v5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
media: omap3isp: Use struct_group() for memcpy() region
tpm: vtpm_proxy: Check length to avoid compiler warning
alpha: Silence -Warray-bounds warnings
m68k: cmpxchg: Dereference matching size
intel_th: msu: Use memset_startat() for clearing hw header
KVM: x86: Replace memset() "optimization" with normal per-field writes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"These changes come in roughly two halves: support of Gustavo A. R.
Silva's struct_size() work via additional helpers for catching
overflow allocation size calculations, and conversions of selftests to
KUnit (which includes some tweaks for UML + Clang):
- Convert overflow selftest to KUnit
- Convert stackinit selftest to KUnit
- Implement size_t saturating arithmetic helpers
- Allow struct_size() to be used in initializers"
* tag 'overflow-v5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
lib: stackinit: Convert to KUnit
um: Allow builds with Clang
lib: overflow: Convert to Kunit
overflow: Provide constant expression struct_size
overflow: Implement size_t saturating arithmetic helpers
test_overflow: Regularize test reporting output
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull kernel hardening updates from Kees Cook:
- Add arm64 Shadow Call Stack support for GCC 12 (Dan Li)
- Avoid memset with stack offset randomization under Clang (Marco
Elver)
- Clean up stackleak plugin to play nice with .noinstr (Kees Cook)
- Check stack depth for greater usercopy hardening coverage (Kees Cook)
* tag 'hardening-v5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arm64: Add gcc Shadow Call Stack support
m68k: Implement "current_stack_pointer"
xtensa: Implement "current_stack_pointer"
usercopy: Check valid lifetime via stack depth
stack: Constrain and fix stack offset randomization with Clang builds
stack: Introduce CONFIG_RANDOMIZE_KSTACK_OFFSET
gcc-plugins/stackleak: Ignore .noinstr.text and .entry.text
gcc-plugins/stackleak: Exactly match strings instead of prefixes
gcc-plugins/stackleak: Provide verbose mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
- Don't use semaphores in always-atomic-context code (Jann Horn)
- Add "ECC:" prefix to ECC messages (Vincent Whitchurch)
* tag 'pstore-v5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore: Don't use semaphores in always-atomic-context code
pstore: Add prefix to ECC messages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull execve updates from Kees Cook:
"Execve and binfmt updates.
Eric and I have stepped up to be the active maintainers of this area,
so here's our first collection. The bulk of the work was in coredump
handling fixes; additional details are noted below:
- Handle unusual AT_PHDR offsets (Akira Kawata)
- Fix initial mapping size when PT_LOADs are not ordered (Alexey
Dobriyan)
- Move more code under CONFIG_COREDUMP (Alexey Dobriyan)
- Fix missing mmap_lock in file_files_note (Eric W. Biederman)
- Remove a.out support for alpha and m68k (Eric W. Biederman)
- Include first pages of non-exec ELF libraries in coredump (Jann
Horn)
- Don't write past end of notes for regset gap in coredump (Rick
Edgecombe)
- Comment clean-ups (Tom Rix)
- Force single empty string when argv is empty (Kees Cook)
- Add NULL argv selftest (Kees Cook)
- Properly redefine PT_GNU_* in terms of PT_LOOS (Kees Cook)
- MAINTAINERS: Update execve entry with tree (Kees Cook)
- Introduce initial KUnit testing for binfmt_elf (Kees Cook)"
* tag 'execve-v5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
binfmt_elf: Don't write past end of notes for regset gap
a.out: Stop building a.out/osf1 support on alpha and m68k
coredump: Don't compile flat_core_dump when coredumps are disabled
coredump: Use the vma snapshot in fill_files_note
coredump/elf: Pass coredump_params into fill_note_info
coredump: Remove the WARN_ON in dump_vma_snapshot
coredump: Snapshot the vmas in do_coredump
coredump: Move definition of struct coredump_params into coredump.h
binfmt_elf: Introduce KUnit test
ELF: Properly redefine PT_GNU_* in terms of PT_LOOS
MAINTAINERS: Update execve entry with more details
exec: cleanup comments
fs/binfmt_elf: Refactor load_elf_binary function
fs/binfmt_elf: Fix AT_PHDR for unusual ELF files
binfmt: move more stuff undef CONFIG_COREDUMP
selftests/exec: Test for empty string on NULL argv
exec: Force single empty string when argv is empty
coredump: Also dump first pages of non-executable ELF libraries
ELF: fix overflow in total mapping size calculation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus
types, causing updates to most SPI device drivers. The branch with
that on has been cross merged with a couple of other trees which added
new SPI drivers this cycle, I'm not expecting any build issues
resulting from the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than
numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021"
[ And this is obviously where that spi change that snuck into the
regulator tree _should_ have been :^]
* tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits)
spi: fsi: Implement a timeout for polling status
spi: Fix erroneous sgs value with min_t()
spi: tegra20: Use of_device_get_match_data()
spi: mediatek: add ipm design support for MT7986
spi: Add compatible for MT7986
spi: sun4i: fix typos in comments
spi: mediatek: support tick_delay without enhance_timing
spi: Update clock-names property for arm pl022
spi: rockchip-sfc: fix platform_get_irq.cocci warning
spi: s3c64xx: Add spi port configuration for Tesla FSD SoC
spi: dt-bindings: samsung: Add fsd spi compatible
spi: topcliff-pch: Prevent usage of potentially stale DMA device
spi: tegra210-quad: combined sequence mode
spi: tegra210-quad: add acpi support
spi: npcm-fiu: Fix typo ("npxm")
spi: Fix Tegra QSPI example
spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ
spi: cadence: fix platform_get_irq.cocci warning
spi: Update NXP Flexspi maintainer details
dt-bindings: mfd: maxim,max77802: Convert to dtschema
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Quite a quiet release for the regulator API, mainly a few new drivers
plus a lot of fixes for the Raspberry Pi panel driver.
There's also a SPI commit in here which I managed to apply to the
wrong tree and then didn't notice until there were too many commits on
top of it, sorry about that.
- Make it easier to use the virtual consumer test driver with DT
systems.
- Substantial overhaul providing various fixes and robustness
improvements for the Raspberry Pi panel driver.
- Support for Qualcomm PMX65 and SDX65, Richtek RT5190A, and Texas
Instruments TPS62864x"
* tag 'regulator-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (26 commits)
regulator: qcom-rpmh: Add support for SDX65
regulator: dt-bindings: Add PMX65 compatibles
regulator: vctrl: Use min() instead of doing it manually
regulator: rt5190a: Add support for Richtek RT5190A PMIC
regulator: Add bindings for Richtek RT5190A PMIC
regulator: Convert TPS62360 binding to json-schema
regulator: cleanup comments
regulator: virtual: add devicetree support
regulator: virtual: warn against production use
regulator: virtual: use dev_err_probe()
regulator: tps62864: Fix bindings for SW property
regulator: Add support for TPS6286x
regulator: Add bindings for TPS62864x
regulator/rpi-panel-attiny: Use two transactions for I2C read
regulator/rpi-panel-attiny: Use the regmap cache
regulator: rpi-panel: Remove get_brightness hook
regulator: rpi-panel: Add GPIO control for panel and touch resets
regulator: rpi-panel: Convert to drive lines directly
regulator: rpi-panel: Ensure the backlight is off during probe.
regulator: rpi-panel: Serialise operations.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A couple of small fixes, plus some new features that enable us to
handle devices that reformat register addresses depending on the bus
used to handle the control interface more gracefully"
* tag 'regmap-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: allow a defined reg_base to be added to every address
regmap: add configurable downshift for addresses
regmap: irq: cleanup comments
regmap-irq: Fix typo in comment
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Texas Instruments TMP464 and TMP468 driver
- Vicor PLI1209BC Digital Supervisor driver
- ASUS EC driver
Improvements to existing drivers:
- adt7x10:
- Convert to use regmap
- convert to use with_info API
- use hwmon_notify_event
- other cleanup
- aquacomputer_d5next:
- Add support for Aquacomputer Farbwerk 360
- asus_wmi_sensors:
- Add ASUS ROG STRIX B450-F GAMING II
- asus_wmi_ec_sensors:
- Support T_Sensor on Prime X570-Pro
- Deprecate driver (replaced by new driver)
- axi-fan-control:
- Use hwmon_notify_event
- dell-smm:
- Clean up CONFIG_I8K
- disable fan type support for Inspiron 3505
- various other cleanup
- hwmon core:
- Report attribute name with udev events
- Add "label" attribute to ABI,
- Add support for pwm auto channels attribute
- max6639:
- Add regulator support
- lm70:
- Add support for TI TMP125
- lm83:
- Cleanup, convert to use with_info API
- mlxreg-fan:
- Use pwm attribute for setting fan speed low limit
- nct6775:
- Add board ID's for ASUS ROG STRIX Z390/Z490/X570-* / PRIME
X570-P, PRIME B550-PLUS, ASUS Pro B550M-C/PRIME B550M-A
- Add support for TSI temperature registers
- occ:
- Add various new sysfs attributes
- pmbus core:
- Handle VIN unit off status
- Add regulator supply into macro
- Add get_error_flags support to regulator ops
- pmbus/adm1275:
- Allow setting sample averaging
- pmbus/lm25066:
- Add regulator support
- pmbus/xdpe12284:
- Add support for xdpe11280
- register as regulator
- powr1220:
- Convert to with_info API
- Add support for Lattice's POWR1014 power manager IC
- sch56xx:
- Cleanup and minor improvements
- sch5627:
- Add pwmX_auto_channels_temp support
- tc654:
- Add thermal_cooling device support"
* tag 'hwmon-for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (86 commits)
hwmon: (dell-smm) Add Inspiron 3505 to fan type blacklist
hwmon: (pmbus) Add Vin unit off handling
hwmon: (scpi-hwmon): Use of_device_get_match_data()
hwmon: (axi-fan-control) Use hwmon_notify_event
hwmon: (vexpress-hwmon) Use of_device_get_match_data()
hwmon: Add driver for Texas Instruments TMP464 and TMP468
dt-bindings: hwmon: add tmp464.yaml
dt-bindings: hwmon: Add sample averaging properties for ADM1275
hwmon: (adm1275) Allow setting sample averaging
hwmon: (xdpe12284) Add regulator support
hwmon: (xdpe12284) Add support for xdpe11280
dt-bindings: trivial-devices: Add xdpe11280
hwmon: (aquacomputer_d5next) Add support for Aquacomputer Farbwerk 360
hwmon: (sch5627) Add pwmX_auto_channels_temp support
hwmon: (core) Add support for pwm auto channels attribute
hwmon: (lm70) Add ti,tmp125 support
dt-bindings: Add ti,tmp125 temperature sensor binding
hwmon: (pmbus/pli1209bc) Add regulator support
hwmon: (pmbus) Add support for pli1209bc
dt-bindings:trivial-devices: Add pli1209bc
...
|
|
git://git.kernel.dk/linux-block
Pull bio_alloc() cleanups from Jens Axboe:
"Filesystem cleanups to pass the bio op to bio_alloc() instead of
setting it just before bio submission".
* tag 'for-5.18/alloc-cleanups-2022-03-18' of git://git.kernel.dk/linux-block:
f2fs: pass the bio operation to bio_alloc_bioset
f2fs: don't pass a bio to f2fs_target_device
nilfs2: pass the operation to bio_alloc
ext4: pass the operation to bio_alloc
mpage: pass the operation to bio_alloc
|
|
Pull block driver updates from Jens Axboe:
- NVMe updates via Christoph:
- add vectored-io support for user-passthrough (Kanchan Joshi)
- add verbose error logging (Alan Adamson)
- support buffered I/O on block devices in nvmet (Chaitanya
Kulkarni)
- central discovery controller support (Martin Belanger)
- fix and extended the globally unique idenfier validation
(Christoph)
- move away from the deprecated IDA APIs (Sagi Grimberg)
- misc code cleanup (Keith Busch, Max Gurtovoy, Qinghua Jin,
Chaitanya Kulkarni)
- add lockdep annotations for in-kernel sockets (Chris Leech)
- use vmalloc for ANA log buffer (Hannes Reinecke)
- kerneldoc fixes (Chaitanya Kulkarni)
- cleanups (Guoqing Jiang, Chaitanya Kulkarni, Christoph)
- warn about shared namespaces without multipathing (Christoph)
- MD updates via Song with a set of cleanups (Christoph, Mariusz, Paul,
Erik, Dirk)
- loop cleanups and queue depth configuration (Chaitanya)
- null_blk cleanups and fixes (Chaitanya)
- Use descriptive init/exit names in virtio_blk (Randy)
- Use bvec_kmap_local() in drivers (Christoph)
- bcache fixes (Mingzhe)
- xen blk-front persistent grant speedups (Juergen)
- rnbd fix and cleanup (Gioh)
- Misc fixes (Christophe, Colin)
* tag 'for-5.18/drivers-2022-03-18' of git://git.kernel.dk/linux-block: (76 commits)
virtio_blk: eliminate anonymous module_init & module_exit
nvme: warn about shared namespaces without CONFIG_NVME_MULTIPATH
nvme: remove nvme_alloc_request and nvme_alloc_request_qid
nvme: cleanup how disk->disk_name is assigned
nvmet: move the call to nvmet_ns_changed out of nvmet_ns_revalidate
nvmet: use snprintf() with PAGE_SIZE in configfs
nvmet: don't fold lines
nvmet-rdma: fix kernel-doc warning for nvmet_rdma_device_removal
nvmet-fc: fix kernel-doc warning for nvmet_fc_unregister_targetport
nvmet-fc: fix kernel-doc warning for nvmet_fc_register_targetport
nvme-tcp: lockdep: annotate in-kernel sockets
nvme-tcp: don't fold the line
nvme-tcp: don't initialize ret variable
nvme-multipath: call bio_io_error in nvme_ns_head_submit_bio
nvme-multipath: use vmalloc for ANA log buffer
xen/blkfront: speed up purge_persistent_grants()
raid5: initialize the stripe_head embeeded bios as needed
raid5-cache: statically allocate the recovery ra bio
raid5-cache: fully initialize flush_bio when needed
raid5-ppl: fully initialize the bio in ppl_new_iounit
...
|
|
Pull block updates from Jens Axboe:
- BFQ cleanups and fixes (Yu, Zhang, Yahu, Paolo)
- blk-rq-qos completion fix (Tejun)
- blk-cgroup merge fix (Tejun)
- Add offline error return value to distinguish it from an IO error on
the device (Song)
- IO stats fixes (Zhang, Christoph)
- blkcg refcount fixes (Ming, Yu)
- Fix for indefinite dispatch loop softlockup (Shin'ichiro)
- blk-mq hardware queue management improvements (Ming)
- sbitmap dead code removal (Ming, John)
- Plugging merge improvements (me)
- Show blk-crypto capabilities in sysfs (Eric)
- Multiple delayed queue run improvement (David)
- Block throttling fixes (Ming)
- Start deprecating auto module loading based on dev_t (Christoph)
- bio allocation improvements (Christoph, Chaitanya)
- Get rid of bio_devname (Christoph)
- bio clone improvements (Christoph)
- Block plugging improvements (Christoph)
- Get rid of genhd.h header (Christoph)
- Ensure drivers use appropriate flush helpers (Christoph)
- Refcounting improvements (Christoph)
- Queue initialization and teardown improvements (Ming, Christoph)
- Misc fixes/improvements (Barry, Chaitanya, Colin, Dan, Jiapeng,
Lukas, Nian, Yang, Eric, Chengming)
* tag 'for-5.18/block-2022-03-18' of git://git.kernel.dk/linux-block: (127 commits)
block: cancel all throttled bios in del_gendisk()
block: let blkcg_gq grab request queue's refcnt
block: avoid use-after-free on throttle data
block: limit request dispatch loop duration
block/bfq-iosched: Fix spelling mistake "tenative" -> "tentative"
sr: simplify the local variable initialization in sr_block_open()
block: don't merge across cgroup boundaries if blkcg is enabled
block: fix rq-qos breakage from skipping rq_qos_done_bio()
block: flush plug based on hardware and software queue order
block: ensure plug merging checks the correct queue at least once
block: move rq_qos_exit() into disk_release()
block: do more work in elevator_exit
block: move blk_exit_queue into disk_release
block: move q_usage_counter release into blk_queue_release
block: don't remove hctx debugfs dir from blk_mq_exit_queue
block: move blkcg initialization/destroy into disk allocation/release handler
sr: implement ->free_disk to simplify refcounting
sd: implement ->free_disk to simplify refcounting
sd: delay calling free_opal_dev
sd: call sd_zbc_release_disk before releasing the scsi_device reference
...
|
|
Some chips using the split VTU/STU design will not accept VTU entries
who's SID points to an invalid STU entry. Therefore, mark all those
chips with either the mv88e6352_g1_stu_* or mv88e6390_g1_stu_* ops as
appropriate.
Notably, chips for the Opal Plus (6085/6097) era seem to use a
different implementation than those from Agate (6352) and onwards,
even though their external interface is the same. The former happily
accepts VTU entries referencing invalid STU entries, while the latter
does not.
This fixes an issue where the driver would fail to probe switch trees
that contained chips of the Agate/Topaz generation which did not
declare STU support, as loaded VTU entries would be read back as
invalid.
Fixes: 49c98c1dc7d9 ("net: dsa: mv88e6xxx: Disentangle STU from VTU")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220319110345.555270-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
`cur64`, `start64` and `ts_delta` are int64_t. Change format
specifiers in fprintf from `"%lu"` to `"%" PRId64` to adapt
to 32-bit and 64-bit systems.
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Link: https://lore.kernel.org/r/20220319073730.5235-1-guozhengkui@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.dk/linux-block
Pull io_uring statx fixes from Jens Axboe:
"On top of the main io_uring branch, this is to ensure that the
filename component of statx is stable after submit.
That requires a few VFS related changes"
* tag 'for-5.18/io_uring-statx-2022-03-18' of git://git.kernel.dk/linux-block:
io-uring: Make statx API stable
|
|
Pull io_uring updates from Jens Axboe:
- Fixes for current file position. Still doesn't have the f_pos_lock
sorted, but it's a step in the right direction (Dylan)
- Tracing updates (Dylan, Stefan)
- Improvements to io-wq locking (Hao)
- Improvements for provided buffers (me, Pavel)
- Support for registered file descriptors (me, Xiaoguang)
- Support for ring messages (me)
- Poll improvements (me)
- Fix for fixed buffers and non-iterator reads/writes (me)
- Support for NAPI on sockets (Olivier)
- Ring quiesce improvements (Usama)
- Misc fixes (Olivier, Pavel)
* tag 'for-5.18/io_uring-2022-03-18' of git://git.kernel.dk/linux-block: (42 commits)
io_uring: terminate manual loop iterator loop correctly for non-vecs
io_uring: don't check unrelated req->open.how in accept request
io_uring: manage provided buffers strictly ordered
io_uring: fold evfd signalling under a slower path
io_uring: thin down io_commit_cqring()
io_uring: shuffle io_eventfd_signal() bits around
io_uring: remove extra barrier for non-sqpoll iopoll
io_uring: fix provided buffer return on failure for kiocb_done()
io_uring: extend provided buf return to fails
io_uring: refactor timeout cancellation cqe posting
io_uring: normilise naming for fill_cqe*
io_uring: cache poll/double-poll state with a request flag
io_uring: cache req->apoll->events in req->cflags
io_uring: move req->poll_refs into previous struct hole
io_uring: make tracing format consistent
io_uring: recycle apoll_poll entries
io_uring: remove duplicated member check for io_msg_ring_prep()
io_uring: allow submissions to continue on error
io_uring: recycle provided buffers if request goes async
io_uring: ensure reads re-import for selected buffers
...
|
|
This series improves perf support for RISC-V based system using SBI PMU
and Sscofpmf extensions, by adding a new generic RISC-V perf framework
along with a pair of drivers: one that usese the new
performance-monitoring extensions and one that keeps support for the
existing systems that only have the legacy counters.
Tested-by: Nikita Shubin <n.shubin@yadro.com>
* palmer/riscv-pmu:
MAINTAINERS: Add entry for RISC-V PMU drivers
Documentation: riscv: Remove the old documentation
RISC-V: Add sscofpmf extension support
RISC-V: Add perf platform driver based on SBI PMU extension
RISC-V: Add RISC-V SBI PMU extension definitions
RISC-V: Add a simple platform driver for RISC-V legacy perf
RISC-V: Add a perf core library for pmu drivers
RISC-V: Add CSR encodings for all HPMCOUNTERS
RISC-V: Remove the current perf implementation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- hwrng core now credits for low-quality RNG devices.
Algorithms:
- Optimisations for neon aes on arm/arm64.
- Add accelerated crc32_be on arm64.
- Add ffdheXYZ(dh) templates.
- Disallow hmac keys < 112 bits in FIPS mode.
- Add AVX assembly implementation for sm3 on x86.
Drivers:
- Add missing local_bh_disable calls for crypto_engine callback.
- Ensure BH is disabled in crypto_engine callback path.
- Fix zero length DMA mappings in ccree.
- Add synchronization between mailbox accesses in octeontx2.
- Add Xilinx SHA3 driver.
- Add support for the TDES IP available on sama7g5 SoC in atmel"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (137 commits)
crypto: xilinx - Turn SHA into a tristate and allow COMPILE_TEST
MAINTAINERS: update HPRE/SEC2/TRNG driver maintainers list
crypto: dh - Remove the unused function dh_safe_prime_dh_alg()
hwrng: nomadik - Change clk_disable to clk_disable_unprepare
crypto: arm64 - cleanup comments
crypto: qat - fix initialization of pfvf rts_map_msg structures
crypto: qat - fix initialization of pfvf cap_msg structures
crypto: qat - remove unneeded assignment
crypto: qat - disable registration of algorithms
crypto: hisilicon/qm - fix memset during queues clearing
crypto: xilinx: prevent probing on non-xilinx hardware
crypto: marvell/octeontx - Use swap() instead of open coding it
crypto: ccree - Fix use after free in cc_cipher_exit()
crypto: ccp - ccp_dmaengine_unregister release dma channels
crypto: octeontx2 - fix missing unlock
hwrng: cavium - fix NULL but dereferenced coccicheck error
crypto: cavium/nitrox - don't cast parameter in bit operations
crypto: vmx - add missing dependencies
MAINTAINERS: Add maintainer for Xilinx ZynqMP SHA3 driver
crypto: xilinx - Add Xilinx SHA3 driver
...
|
|
The Felix switch has 6 ports, 2 of which are internal.
Due to some misunderstanding, my initial suggestion for
vsc9959_port_modes[]:
https://patchwork.kernel.org/project/netdevbpf/patch/20220129220221.2823127-10-colin.foster@in-advantage.com/#24718277
got translated by Colin into a 5-port array, leading to an all-zero port
mode mask for port 5.
Fixes: acf242fc739e ("net: dsa: felix: remove prevalidate_phy_mode interface")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220318195812.276276-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tobias Waldekranz says:
====================
net: dsa: mv88e6xxx: MST Fixes
1/2 fixes the issue reported by Marek here:
https://lore.kernel.org/netdev/20220318182817.5ade8ecd@dellmb/
2/2 adds a missing capability check to the new .vlan_msti_set
callback.
====================
Link: https://lore.kernel.org/r/20220318201321.4010543-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the same way that we check for STU support in the MST state
callback, we should also verify it before trying to change a VLANs
MSTI membership.
Fixes: acaf4d2e36b3 ("net: dsa: mv88e6xxx: MST Offloading")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simply having a physical STU table in the device doesn't do us any
good if there's no implementation of the relevant ops to access that
table. So ensure that chips that claim STU support can also talk to
the hardware.
This fixes an issue where chips that had a their ->info->max_sid
set (due to their family membership), but no implementation (due to
their chip-specific ops struct) would fail to probe.
Fixes: 49c98c1dc7d9 ("net: dsa: mv88e6xxx: Disentangle STU from VTU")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add myself and Anup as maintainer for RISC-V PMU drivers.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The existing pmu documentation describes the limitation of perf
infrastructure in RISC-V ISA and limited feature set of perf in RISC-V.
However, SBI PMU extension and sscofpmf extension(ISA extension) allows to
implement most of the required features of perf. Remove the old
documentation which is not accurate anymore.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The sscofpmf extension allows counter overflow and filtering for
programmable counters. Enable the perf driver to handle the overflow
interrupt. The overflow interrupt is a hart local interrupt.
Thus, per cpu overflow interrupts are setup as a child under the root
INTC irq domain.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
RISC-V SBI specification added a PMU extension that allows to configure
start/stop any pmu counter. The RISC-V perf can use most of the generic
perf features except interrupt overflow and event filtering based on
privilege mode which will be added in future.
It also allows to monitor a handful of firmware counters that can provide
insights into firmware activity during a performance analysis.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
This patch adds all the definitions defined by the SBI PMU extension.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The old RISC-V perf implementation allowed counting of only
cycle/instruction counters using perf. Restore that feature by implementing
a simple platform driver under a separate config to provide backward
compatibility. Any existing software stack will continue to work as it is.
However, it provides an easy way out in future where we can remove the
legacy driver.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Implement a perf core library that can support all the essential perf
features in future. It can also accommodate any type of PMU implementation
in future. Currently, both SBI based perf driver and legacy driver
implemented uses the library. Most of the common perf functionalities
are kept in this core library wile PMU specific driver can implement PMU
specific features. For example, the SBI specific functionality will be
implemented in the SBI specific driver.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Ziyang Xuan says:
====================
net/tls: some optimizations for tls
Do some small optimizations for tls, including jump instructions
optimization, and judgement processes optimization.
====================
Link: https://lore.kernel.org/r/cover.1647658604.git.william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Linux kernel can directly read these counters as the HPMCOUNTERS CSRs are
accessible in S-mode.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
It is known that priority setting HW offload when set tls TX/RX offload
by setsockopt(). Check netdevice whether support NETIF_F_HW_TLS_TX or
not at the later stages in the whole tls_set_device_offload() process,
some memory allocations have been done before that. We must release those
memory and return error if we judge the netdevice not support
NETIF_F_HW_TLS_TX. It is redundant.
Move NETIF_F_HW_TLS_TX judgement forward, and move start_marker_record
and offload_ctx memory allocation back slightly. Thus, we can get
simpler exception handling process.
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoid using "goto" jump instruction unconditionally when we
can return directly. Remove unnecessary jump instructions in
do_tls_setsockopt_conf().
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current perf implementation in RISC-V is not very useful as it can not
count any events other than cycle/instructions. Moreover, perf record
can not be used or the events can not be started or stopped.
Remove the implementation now for a better platform driver in future
that will implement most of the missing functionality.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator updates from Jason Donenfeld:
"There have been a few important changes to the RNG's crypto, but the
intent for 5.18 has been to shore up the existing design as much as
possible with modern cryptographic functions and proven constructions,
rather than actually changing up anything fundamental to the RNG's
design.
So it's still the same old RNG at its core as before: it still counts
entropy bits, and collects from the various sources with the same
heuristics as before, and so forth. However, the cryptographic
algorithms that transform that entropic data into safe random numbers
have been modernized.
Just as important, if not more, is that the code has been cleaned up
and re-documented. As one of the first drivers in Linux, going back to
1.3.30, its general style and organization was showing its age and
becoming both a maintenance burden and an auditability impediment.
Hopefully this provides a more solid foundation to build on for the
future. I encourage you to open up the file in full, and maybe you'll
remark, "oh, that's what it's doing," and enjoy reading it. That, at
least, is the eventual goal, which this pull begins working toward.
Here's a summary of the various patches in this pull:
- /dev/urandom and /dev/random now do the same thing, per the patch
we discussed on the list. I think this is worth trying out. If it
does appear problematic, I've made sure to keep it standalone and
revertible without any conflicts.
- Fixes and cleanups for numerous integer type problems, locking
issues, and general code quality concerns.
- The input pool's LFSR has been replaced with a cryptographically
secure hash function, which has security and performance benefits
alike, and consequently allows us to count entropy bits linearly.
- The pre-init injection now uses a real hash function too, instead
of an LFSR or vanilla xor.
- The interrupt handler's fast_mix() function now uses one round of
SipHash, rather than the fake crypto that was there before.
- All additions of RDRAND and RDSEED now go through the input pool's
hash function, in part to mitigate ridiculous hypothetical CPU
backdoors, but more so to have a consistent interface for ingesting
entropy that's easy to analyze, making everything happen one way,
instead of a potpourri of different ways.
- The crng now works on per-cpu data, while also being in accordance
with the actual "fast key erasure RNG" design. This allows us to
fix several boot-time race complications associated with the prior
dynamically allocated model, eliminates much locking, and makes our
backtrack protection more robust.
- Batched entropy now erases doled out values so that it's backtrack
resistant.
- Working closely with Sebastian, the interrupt handler no longer
needs to take any locks at all, as we punt the
synchronized/expensive operations to a workqueue. This is
especially nice for PREEMPT_RT, where taking spinlocks in irq
context is problematic. It also makes the handler faster for the
rest of us.
- Also working with Sebastian, we now do the right thing on CPU
hotplug, so that we don't use stale entropy or fail to accumulate
new entropy when CPUs come back online.
- We handle virtual machines that fork / clone / snapshot, using the
"vmgenid" ACPI specification for retrieving a unique new RNG seed,
which we can use to also make WireGuard (and in the future, other
things) safe across VM forks.
- Around boot time, we now try to reseed more often if enough entropy
is available, before settling on the usual 5 minute schedule.
- Last, but certainly not least, the documentation in the file has
been updated considerably"
* tag 'random-5.18-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (60 commits)
random: check for signal and try earlier when generating entropy
random: reseed more often immediately after booting
random: make consistent usage of crng_ready()
random: use SipHash as interrupt entropy accumulator
wireguard: device: clear keys on VM fork
random: provide notifier for VM fork
random: replace custom notifier chain with standard one
random: do not export add_vmfork_randomness() unless needed
virt: vmgenid: notify RNG of VM fork and supply generation ID
ACPI: allow longer device IDs
random: add mechanism for VM forks to reinitialize crng
random: don't let 644 read-only sysctls be written to
random: give sysctl_random_min_urandom_seed a more sensible value
random: block in /dev/urandom
random: do crng pre-init loading in worker rather than irq
random: unify cycles_t and jiffies usage and types
random: cleanup UUID handling
random: only wake up writers after zap if threshold was passed
random: round-robin registers as ulong, not u32
random: clear fast pool, crng, and batches in cpuhp bring up
...
|
|
Compiled with clang by adding LLVM=1 both kernel and selftests/bpf
build, I hit the following compilation error:
In file included from /.../tools/testing/selftests/bpf/prog_tests/subskeleton.c:6:
./test_subskeleton_lib.subskel.h:168:6: error: variable 'err' is used uninitialized whenever
'if' condition is true [-Werror,-Wsometimes-uninitialized]
if (!s->progs)
^~~~~~~~~
./test_subskeleton_lib.subskel.h:181:11: note: uninitialized use occurs here
errno = -err;
^~~
./test_subskeleton_lib.subskel.h:168:2: note: remove the 'if' if its condition is always false
if (!s->progs)
^~~~~~~~~~~~~~
The compilation error is triggered by the following code
...
int err;
obj = (struct test_subskeleton_lib *)calloc(1, sizeof(*obj));
if (!obj) {
errno = ENOMEM;
goto err;
}
...
err:
test_subskeleton_lib__destroy(obj);
errno = -err;
...
in test_subskeleton_lib__open(). The 'err' is not initialized, yet it
is used in 'errno = -err' later.
The fix is to remove 'errno = -err' since errno has been set properly
in all incoming branches.
Fixes: 00389c58ffe9 ("bpftool: Add support for subskeletons")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20220320032009.3106133-1-yhs@fb.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull PnP update from Rafael Wysocki:
"Replace acpi_bus_get_device() in the PNP code with
acpi_fetch_acpi_dev() which is better"
* tag 'pnp-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PNP: Replace acpi_bus_get_device()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"As far as new functionality is concerned, there is a new thermal
driver for the Intel Hardware Feedback Interface (HFI) along with some
intel-speed-select utility changes to support it. There are also new
DT compatible strings for a couple of platforms, and thermal zones on
some platforms will be registered as HWmon sensors now.
Apart from the above, some drivers are updated (fixes mostly) and
there is a new piece of documentation for the Intel DPTF (Dynamic
Power and Thermal Framework) sysfs interface.
Specifics:
- Add a new thermal driver for the Intel Hardware Feedback Interface
(HFI) including the HFI initialization, HFI notification interrupt
handling and sending CPU capabilities change messages to user space
via the thermal netlink interface (Ricardo Neri, Srinivas
Pandruvada, Nathan Chancellor, Randy Dunlap).
- Extend the intel-speed-select utility to handle out-of-band CPU
configuration changes and add support for the CPU capabilities
change messages sent over the thermal netlink interface by the new
HFI thermal driver to it (Srinivas Pandruvada).
- Convert the DT bindings to yaml format for the Exynos platform and
fix and update the MAINTAINERS file for this driver (Krzysztof
Kozlowski).
- Register the thermal zones as HWmon sensors for the QCom's Tsens
driver and TI thermal platforms (Dmitry Baryshkov, Romain Naour).
- Add the msm8953 compatible documentation in the bindings (Luca
Weiss).
- Add the sm8150 platform support to the QCom LMh driver's DT binding
(Thara Gopinath).
- Check the command result from the IPC command to the BPMP in the
Tegra driver (Mikko Perttunen).
- Silence the error for normal configuration where the interrupt is
optionnal in the Broadcom thermal driver (Florian Fainelli).
- Remove remaining dead code from the TI thermal driver (Yue
Haibing).
- Don't use bitmap_weight() in end_power_clamp() in the powerclamp
driver (Yury Norov).
- Update the OS policy capabilities handshake in the int340x thermal
driver (Srinivas Pandruvada).
- Increase the policies bitmap size in int340x (Srinivas Pandruvada).
- Replace acpi_bus_get_device() with acpi_fetch_acpi_dev() in the
int340x thermal driver (Rafael Wysocki).
- Check for NULL after calling kmemdup() in int340x (Jiasheng Jiang).
- Add Intel Dynamic Power and Thermal Framework (DPTF) kernel
interface documentation (Srinivas Pandruvada).
- Fix bullet list warning in the thermal documentation (Randy
Dunlap)"
* tag 'thermal-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (30 commits)
thermal: int340x: Update OS policy capability handshake
thermal: int340x: Increase bitmap size
Documentation: thermal: DPTF Documentation
MAINTAINERS: thermal: samsung: update Krzysztof Kozlowski's email
thermal/drivers/ti-soc-thermal: Remove unused function ti_thermal_get_temp()
thermal/drivers/brcmstb_thermal: Interrupt is optional
thermal: tegra-bpmp: Handle errors in BPMP response
drivers/thermal/ti-soc-thermal: Add hwmon support
dt-bindings: thermal: tsens: Add msm8953 compatible
dt-bindings: thermal: Add sm8150 compatible string for LMh
thermal/drivers/qcom/lmh: Add support for sm8150
thermal/drivers/tsens: register thermal zones as hwmon sensors
MAINTAINERS: thermal: samsung: Drop obsolete properties
dt-bindings: thermal: samsung: Convert to dtschema
tools/power/x86/intel-speed-select: v1.12 release
tools/power/x86/intel-speed-select: HFI support
tools/power/x86/intel-speed-select: OOB daemon mode
thermal: intel: hfi: INTEL_HFI_THERMAL depends on NET
thermal: netlink: Fix parameter type of thermal_genl_cpu_capability_event() stub
thermal: Replace acpi_bus_get_device()
...
|
|
tp->rx_opt.mss_clamp is not populated, yet, during TFO send so we
rise it to the local MSS. tp->mss_cache is not updated, however:
tcp_v6_connect():
tp->rx_opt.mss_clamp = IPV6_MIN_MTU - headers;
tcp_connect():
tcp_connect_init():
tp->mss_cache = min(mtu, tp->rx_opt.mss_clamp)
tcp_send_syn_data():
tp->rx_opt.mss_clamp = tp->advmss
After recent fixes to ICMPv6 PTB handling we started dropping
PMTU updates higher than tp->mss_cache. Because of the stale
tp->mss_cache value PMTU updates during TFO are always dropped.
Thanks to Wei for helping zero in on the problem and the fix!
Fixes: c7bb4b89033b ("ipv6: tcp: drop silly ICMPv6 packet too big messages")
Reported-by: Andre Nash <alnash@fb.com>
Reported-by: Neil Spring <ntspring@fb.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220321165957.1769954-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over the code and a new piece
of documentation for Intel uncore frequency scaling.
Functionality-wise, the intel_idle driver will support Sapphire Rapids
Xeons natively now (with some extra facilities for controlling
C-states more precisely on those systems), virtual guests will take
the ACPI S4 hardware signature into account by default, the
intel_pstate driver will take the defualt EPP value from the firmware,
cpupower utility will support the AMD P-state driver added in the
previous cycle, and there is a new tracer utility for that driver.
Specifics:
- Allow device_pm_check_callbacks() to be called from interrupt
context without issues (Dmitry Baryshkov).
- Modify devm_pm_runtime_enable() to automatically handle
pm_runtime_dont_use_autosuspend() at driver exit time (Douglas
Anderson).
- Make the schedutil cpufreq governor use to_gov_attr_set() instead
of open coding it (Kevin Hao).
- Replace acpi_bus_get_device() with acpi_fetch_acpi_dev() in the
cpufreq longhaul driver (Rafael Wysocki).
- Unify show() and store() naming in cpufreq and make it use
__ATTR_XX (Lianjie Zhang).
- Make the intel_pstate driver use the EPP value set by the firmware
by default (Srinivas Pandruvada).
- Re-order the init checks in the powernow-k8 cpufreq driver (Mario
Limonciello).
- Make the ACPI processor idle driver check for architectural support
for LPI to avoid using it on x86 by mistake (Mario Limonciello).
- Add Sapphire Rapids Xeon support to the intel_idle driver (Artem
Bityutskiy).
- Add 'preferred_cstates' module argument to the intel_idle driver to
work around C1 and C1E handling issue on Sapphire Rapids (Artem
Bityutskiy).
- Add core C6 optimization on Sapphire Rapids to the intel_idle
driver (Artem Bityutskiy).
- Optimize the haltpoll cpuidle driver a bit (Li RongQing).
- Remove leftover text from intel_idle() kerneldoc comment and fix up
white space in intel_idle (Rafael Wysocki).
- Fix load_image_and_restore() error path (Ye Bin).
- Fix typos in comments in the system wakeup hadling code (Tom Rix).
- Clean up non-kernel-doc comments in hibernation code (Jiapeng
Chong).
- Fix __setup handler error handling in system-wide suspend and
hibernation core code (Randy Dunlap).
- Add device name to suspend_report_result() (Youngjin Jang).
- Make virtual guests honour ACPI S4 hardware signature by default
(David Woodhouse).
- Block power off of a parent PM domain unless child is in deepest
state (Ulf Hansson).
- Use dev_err_probe() to simplify error handling for generic PM
domains (Ahmad Fatoum).
- Fix sleep-in-atomic bug caused by genpd_debug_remove() (Shawn Guo).
- Document Intel uncore frequency scaling (Srinivas Pandruvada).
- Add DTPM hierarchy description (Daniel Lezcano).
- Change the locking scheme in DTPM (Daniel Lezcano).
- Fix dtpm_cpu cleanup at exit time and missing virtual DTPM pointer
release (Daniel Lezcano).
- Make dtpm_node_callback[] static (kernel test robot).
- Fix spelling mistake "initialze" -> "initialize" in
dtpm_create_hierarchy() (Colin Ian King).
- Add tracer tool for the amd-pstate driver (Jinzhou Su).
- Fix PC6 displaying in turbostat on some systems (Artem Bityutskiy).
- Add AMD P-State support to the cpupower utility (Huang Rui)"
* tag 'pm-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (58 commits)
cpufreq: powernow-k8: Re-order the init checks
cpuidle: intel_idle: Drop redundant backslash at line end
cpuidle: intel_idle: Update intel_idle() kerneldoc comment
PM: hibernate: Honour ACPI hardware signature by default for virtual guests
cpufreq: intel_pstate: Use firmware default EPP
cpufreq: unify show() and store() naming and use __ATTR_XX
PM: core: keep irq flags in device_pm_check_callbacks()
cpuidle: haltpoll: Call cpuidle_poll_state_init() later
Documentation: amd-pstate: add tracer tool introduction
tools/power/x86/amd_pstate_tracer: Add tracer tool for AMD P-state
tools/power/x86/intel_pstate_tracer: make tracer as a module
cpufreq: amd-pstate: Add more tracepoint for AMD P-State module
PM: sleep: Add device name to suspend_report_result()
turbostat: fix PC6 displaying on some systems
intel_idle: add core C6 optimization for SPR
intel_idle: add 'preferred_cstates' module argument
intel_idle: add SPR support
PM: runtime: Have devm_pm_runtime_enable() handle pm_runtime_dont_use_autosuspend()
ACPI: processor idle: Check for architectural support for LPI
cpuidle: PSCI: Move the `has_lpi` check to the beginning of the function
...
|
|
GCC12 appears to be much smarter about its dependency tracking and is
aware that the relaxed variants are just normal loads and stores and
this is causing problems like:
[ 210.074549] ------------[ cut here ]------------
[ 210.079223] NETDEV WATCHDOG: enabcm6e4ei0 (bcmgenet): transmit queue 1 timed out
[ 210.086717] WARNING: CPU: 1 PID: 0 at net/sched/sch_generic.c:529 dev_watchdog+0x234/0x240
[ 210.095044] Modules linked in: genet(E) nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat]
[ 210.146561] ACPI CPPC: PCC check channel failed for ss: 0. ret=-110
[ 210.146927] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G E 5.17.0-rc7G12+ #58
[ 210.153226] CPPC Cpufreq:cppc_scale_freq_workfn: failed to read perf counters
[ 210.161349] Hardware name: Raspberry Pi Foundation Raspberry Pi 4 Model B/Raspberry Pi 4 Model B, BIOS EDK2-DEV 02/08/2022
[ 210.161353] pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 210.161358] pc : dev_watchdog+0x234/0x240
[ 210.161364] lr : dev_watchdog+0x234/0x240
[ 210.161368] sp : ffff8000080a3a40
[ 210.161370] x29: ffff8000080a3a40 x28: ffffcd425af87000 x27: ffff8000080a3b20
[ 210.205150] x26: ffffcd425aa00000 x25: 0000000000000001 x24: ffffcd425af8ec08
[ 210.212321] x23: 0000000000000100 x22: ffffcd425af87000 x21: ffff55b142688000
[ 210.219491] x20: 0000000000000001 x19: ffff55b1426884c8 x18: ffffffffffffffff
[ 210.226661] x17: 64656d6974203120 x16: 0000000000000001 x15: 6d736e617274203a
[ 210.233831] x14: 2974656e65676d63 x13: ffffcd4259c300d8 x12: ffffcd425b07d5f0
[ 210.241001] x11: 00000000ffffffff x10: ffffcd425b07d5f0 x9 : ffffcd4258bdad9c
[ 210.248171] x8 : 00000000ffffdfff x7 : 000000000000003f x6 : 0000000000000000
[ 210.255341] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000001000
[ 210.262511] x2 : 0000000000001000 x1 : 0000000000000005 x0 : 0000000000000044
[ 210.269682] Call trace:
[ 210.272133] dev_watchdog+0x234/0x240
[ 210.275811] call_timer_fn+0x3c/0x15c
[ 210.279489] __run_timers.part.0+0x288/0x310
[ 210.283777] run_timer_softirq+0x48/0x80
[ 210.287716] __do_softirq+0x128/0x360
[ 210.291392] __irq_exit_rcu+0x138/0x140
[ 210.295243] irq_exit_rcu+0x1c/0x30
[ 210.298745] el1_interrupt+0x38/0x54
[ 210.302334] el1h_64_irq_handler+0x18/0x24
[ 210.306445] el1h_64_irq+0x7c/0x80
[ 210.309857] arch_cpu_idle+0x18/0x2c
[ 210.313445] default_idle_call+0x4c/0x140
[ 210.317470] cpuidle_idle_call+0x14c/0x1a0
[ 210.321584] do_idle+0xb0/0x100
[ 210.324737] cpu_startup_entry+0x30/0x8c
[ 210.328675] secondary_start_kernel+0xe4/0x110
[ 210.333138] __secondary_switched+0x94/0x98
The assumption when these were relaxed seems to be that device memory
would be mapped non reordering, and that other constructs
(spinlocks/etc) would provide the barriers to assure that packet data
and in memory rings/queues were ordered with respect to device
register reads/writes. This itself seems a bit sketchy, but the real
problem with GCC12 is that it is moving the actual reads/writes around
at will as though they were independent operations when in truth they
are not, but the compiler can't know that. When looking at the
assembly dumps for many of these routines its possible to see very
clean, but not strictly in program order operations occurring as the
compiler would be free to do if these weren't actually register
reads/write operations.
Its possible to suppress the timeout with a liberal bit of dma_mb()'s
sprinkled around but the device still seems unable to reliably
send/receive data. A better plan is to use the safer readl/writel
everywhere.
Since this partially reverts an older commit, which notes the use of
the relaxed variants for performance reasons. I would suggest that
any performance problems with this commit are targeted at relaxing only
the performance critical code paths after assuring proper barriers.
Fixes: 69d2ea9c79898 ("net: bcmgenet: Use correct I/O accessors")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220310045358.224350-1-jeremy.linton@arm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"From the new functionality perspective, the most significant items
here are the new driver for the 'ARM Generic Diagnostic Dump and
Reset' device, the extension of fine grain fan control in the ACPI fan
driver, and the change making it possible to use CPPC information to
obtain CPU capacity.
There are also a few new quirks, a bunch of fixes, including the
platform-level _OSC handling change to make it actually take the
platform firmware response into account, some code and documentation
cleanups, and a notable update of the ACPI device enumeration
documentation.
Specifics:
- Use uintptr_t and offsetof() in the ACPICA code to avoid compiler
warnings regarding NULL pointer arithmetic (Rafael Wysocki).
- Fix possible NULL pointer dereference in acpi_ns_walk_namespace()
when passed "acpi=off" in the command line (Rafael Wysocki).
- Fix and clean up acpi_os_read/write_port() (Rafael Wysocki).
- Introduce acpi_bus_for_each_dev() and use it for walking all ACPI
device objects in the Type C code (Rafael Wysocki).
- Fix the _OSC platform capabilities negotioation and prevent CPPC
from being used if the platform firmware indicates that it not
supported via _OSC (Rafael Wysocki).
- Use ida_alloc() instead of ida_simple_get() for ACPI enumeration of
devices (Rafael Wysocki).
- Add AGDI and CEDT to the list of known ACPI table signatures (Ilkka
Koskinen, Robert Kiraly).
- Add power management debug messages related to suspend-to-idle in
two places (Rafael Wysocki).
- Fix __acpi_node_get_property_reference() return value and clean up
that function (Andy Shevchenko, Sakari Ailus).
- Fix return value of the __setup handler in the ACPI PM timer clock
source driver (Randy Dunlap).
- Clean up double words in two comments (Tom Rix).
- Add "skip i2c clients" quirks for Lenovo Yoga Tablet 1050F/L and
Nextbook Ares 8 (Hans de Goede).
- Clean up frequency invariance handling on x86 in the ACPI CPPC
library (Huang Rui).
- Work around broken XSDT on the Advantech DAC-BJ01 board (Mark
Cilissen).
- Make wakeup events checks in the ACPI EC driver more
straightforward and clean up acpi_ec_submit_event() (Rafael
Wysocki).
- Make it possible to obtain the CPU capacity with the help of CPPC
information (Ionela Voinescu).
- Improve fine grained fan control in the ACPI fan driver and
document it (Srinivas Pandruvada).
- Add device HID and quirk for Microsoft Surface Go 3 to the ACPI
battery driver (Maximilian Luz).
- Make the ACPI driver for Intel SoCs (LPSS) let the SPI driver know
the exact type of the controller (Andy Shevchenko).
- Force native backlight mode on Clevo NL5xRU and NL5xNU (Werner
Sembach).
- Fix return value of __setup handlers in the APEI code (Randy
Dunlap).
- Add Arm Generic Diagnostic Dump and Reset device driver (Ilkka
Koskinen).
- Limit printable size of BERT table data (Darren Hart).
- Fix up HEST and GHES initialization (Shuai Xue).
- Update the ACPI device enumeration documentation and unify the ASL
style in GPIO-related examples (Andy Shevchenko)"
* tag 'acpi-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
clocksource: acpi_pm: fix return value of __setup handler
ACPI: bus: Avoid using CPPC if not supported by firmware
Revert "ACPI: Pass the same capabilities to the _OSC regardless of the query flag"
ACPI: video: Force backlight native for Clevo NL5xRU and NL5xNU
arm64, topology: enable use of init_cpu_capacity_cppc()
arch_topology: obtain cpu capacity using information from CPPC
x86, ACPI: rename init_freq_invariance_cppc() to arch_init_invariance_cppc()
ACPI: AGDI: Add driver for Arm Generic Diagnostic Dump and Reset device
ACPI: tables: Add AGDI to the list of known table signatures
ACPI/APEI: Limit printable size of BERT table data
ACPI: docs: gpio-properties: Unify ASL style for GPIO examples
ACPI / x86: Work around broken XSDT on Advantech DAC-BJ01 board
ACPI: APEI: fix return value of __setup handlers
x86/ACPI: CPPC: Move init_freq_invariance_cppc() into x86 CPPC
x86: Expose init_freq_invariance() to topology header
x86/ACPI: CPPC: Move AMD maximum frequency ratio setting function into x86 CPPC
x86/ACPI: CPPC: Rename cppc_msr.c to cppc.c
ACPI / x86: Add skip i2c clients quirk for Lenovo Yoga Tablet 1050F/L
ACPI / x86: Add skip i2c clients quirk for Nextbook Ares 8
ACPICA: Avoid walking the ACPI Namespace if it is not there
...
|
