| Age | Commit message (Collapse) | Author |
|---|
|
Current code ("qeth_l3_ip_from_hash()") matches a queried address object
against objects in the IP table by IP address, Mask/Prefix Length and
MAC address ("qeth_l3_ipaddrs_is_equal()"). But what callers actually
require is either
a) "is this IP address registered" (ie. match by IP address only),
before adding a new address.
b) or "is this address object registered" (ie. match all relevant
attributes), before deleting an address.
Right now
1. the ADD path is too strict in its lookup, and eg. doesn't detect
conflicts between an existing NORMAL address and a new VIPA address
(because the NORMAL address will have mask != 0, while VIPA has
a mask == 0),
2. the DELETE path is not strict enough, and eg. allows del_rxip() to
delete a VIPA address as long as the IP address matches.
Fix all this by adding helpers (_addr_match_ip() and _addr_match_all())
that do the appropriate checking.
Note that the ADD path for NORMAL addresses is special, as qeth keeps
track of how many times such an address is in use (and there is no
immediate way of returning errors to the caller). So when a requested
NORMAL address _fully_ matches an existing one, it's not considered a
conflict and we merely increment the refcount.
Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit cb816192d986f7596009dedcf2201fe2e5bc2aa7.
The issue this attempted to fix never actually occurs.
l3_add_rxip() checks (via l3_ip_from_hash()) if the requested address
was previously added to the card. If so, it returns -EEXIST and doesn't
call l3_add_ip().
As a result, the "address exists" path in l3_add_ip() is never taken
for rxip addresses, and this patch had no effect.
Fixes: cb816192d986 ("s390/qeth: fix using of ref counter for rxip addresses")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Registering an IPv4 address with the HW takes quite a while, so we
temporarily drop the ip_htable lock. Any concurrent add/remove of the
same IP adjusts the IP's use count, and (on remove) is then blocked by
addr->in_progress.
After the register call has completed, we check the use count for
concurrently attempted add/remove calls - and possibly straight-away
deregister the IP again. This happens via l3_delete_ip(), which
1) looks up the queried IP in the htable (getting a reference to the
*same* queried object),
2) deregisters the IP from the HW, and
3) frees the IP object.
The caller in l3_add_ip() then does a second free on the same object.
For this case, skip all the extra checks and lookups in l3_delete_ip()
and just deregister & free the IP object ourselves.
Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the HW is not reachable, then none of the IPs in qeth's internal
table has been registered with the HW yet. So when deleting such an IP,
there's no need to stage it for deregistration - just drop it from
the table.
This fixes the "add-delete-add" scenario on an offline card, where the
the second "add" merely increments the IP's use count. But as the IP is
still set to DISP_ADDR_DELETE from the previous "delete" step,
l3_recover_ip() won't register it with the HW when the card goes online.
Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth_get_elements_for_range() doesn't know how to handle a 0-length
range (ie. start == end), and returns 1 when it should return 0.
Such ranges occur on TSO skbs, where the L2/L3/L4 headers (and thus all
of the skb's linear data) are skipped when mapping the skb into regular
buffer elements.
This overestimation may cause several performance-related issues:
1. sub-optimal IO buffer selection, where the next buffer gets selected
even though the skb would actually still fit into the current buffer.
2. forced linearization, if the element count for a non-linear skb
exceeds QETH_MAX_BUFFER_ELEMENTS.
Rather than modifying qeth_get_elements_for_range() and adding overhead
to every caller, fix up those callers that are in risk of passing a
0-length range.
Fixes: 2863c61334aa ("qeth: refactor calculation of SBALE count")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't include in the Rx bytecount of the packet sent up the stack:
the FCB (frame control block), and the padding bytes inserted by
the controller into the frame payload, nor the FCS. All these are
being pulled out of the skb by gfar_process_frame().
This issue is old, likely from the driver's beginnings, however
it was amplified by recent:
commit d903ec77118c ("gianfar: simplify FCS handling and fix memory leak")
which basically added the FCS to the Rx bytecount, and so brought
this to my attention.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Continue the switch table detection whack-a-mole. Add a check to
distinguish KASAN data reads from switch data reads. The switch jump
tables in .rodata have relocations associated with them.
This fixes the following warning:
crypto/asymmetric_keys/x509_cert_parser.o: warning: objtool: x509_note_pkey_algo()+0xa4: sibling call from callable instruction with modified stack frame
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/d7c8853022ad47d158cb81e953a40469fc08a95e.1519784382.git.jpoimboe@redhat.com
|
|
Older Xen versions (4.5 and before) might have problems migrating pv
guests with MSR_IA32_SPEC_CTRL having a non-zero value. So before
suspending zero that MSR and restore it after being resumed.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Cc: boris.ostrovsky@oracle.com
Link: https://lkml.kernel.org/r/20180226140818.4849-1-jgross@suse.com
|
|
Commit 6de3f79112cc ("arm_pmu: explicitly enable/disable SPIs at hotplug")
moved all of the arm_pmu IRQ enable/disable calls to the CPU hotplug hooks,
regardless of whether they are implemented as PPIs or SPIs. This can
lead to us sleeping from atomic context due to disable_irq blocking:
| BUG: sleeping function called from invalid context at kernel/irq/manage.c:112
| in_atomic(): 1, irqs_disabled(): 128, pid: 15, name: migration/1
| no locks held by migration/1/15.
| irq event stamp: 192
| hardirqs last enabled at (191): [<00000000803c2507>]
| _raw_spin_unlock_irq+0x2c/0x4c
| hardirqs last disabled at (192): [<000000007f57ad28>] multi_cpu_stop+0x9c/0x140
| softirqs last enabled at (0): [<0000000004ee1b58>]
| copy_process.isra.77.part.78+0x43c/0x1504
| softirqs last disabled at (0): [< (null)>] (null)
| CPU: 1 PID: 15 Comm: migration/1 Not tainted 4.16.0-rc3-salvator-x #1651
| Hardware name: Renesas Salvator-X board based on r8a7796 (DT)
| Call trace:
| dump_backtrace+0x0/0x140
| show_stack+0x14/0x1c
| dump_stack+0xb4/0xf0
| ___might_sleep+0x1fc/0x218
| __might_sleep+0x70/0x80
| synchronize_irq+0x40/0xa8
| disable_irq+0x20/0x2c
| arm_perf_teardown_cpu+0x80/0xac
Since the interrupt is always CPU-affine and this code is running with
interrupts disabled, we can just use disable_irq_nosync as we know there
isn't a concurrent invocation of the handler to worry about.
Fixes: 6de3f79112cc ("arm_pmu: explicitly enable/disable SPIs at hotplug")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Omitting suffixes from instructions in AT&T mode is bad practice when
operand size cannot be determined by the assembler from register
operands, and is likely going to be warned about by upstream gas in the
future (mine does already). Add the missing suffixes here. Note that for
64-bit this means some operations change from being 32-bit to 64-bit.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/5A93F98702000078001ABACC@prv-mh.provo.novell.com
|
|
Omitting suffixes from instructions in AT&T mode is bad practice when
operand size cannot be determined by the assembler from register
operands, and is likely going to be warned about by upstream gas in the
future (mine does already). Add the single missing suffix here.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/5A93F96902000078001ABAC8@prv-mh.provo.novell.com
|
|
As done in commit 3b3a371cc9bc ("x86/debug: Use UD2 for WARN()"), this
switches to UD2 from UD0 to keep disassembly readable.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20180225165056.GA11719@beast
|
|
TIMER0 interrupt ACK is different for ARC700 and HS3x cores.
This came to light in some internal discussions and it is nice to have this
documented rather than digging up the PRM (Programmers Reference Manual).
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Link: https://lkml.kernel.org/r/1519241491-12570-1-git-send-email-vgupta@synopsys.com
|
|
__gic_clocksource_init() extracts the GIC_CONFIG_COUNTBITS field from
read_gic_config() by right shifting the register value. The shift count is
determined by the most significant bit (__fls) of the bitmask which is
wrong as it shifts out the complete bitfield.
Use the least significant bit (__ffs) instead to shift the bitfield down to
bit 0.
Fixes: e07127a077c7 ("clocksource: mips-gic-timer: Use new GIC accessor functions")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: daniel.lezcano@linaro.org
Cc: paul.burton@imgtec.com
Link: https://lkml.kernel.org/r/20180228095610.50341-1-nbd@nbd.name
|
|
The tm-resched-dscr test links against pmu/lib.o, but we don't have a
rule to clean pmu/lib.o. This can lead to a build break if you build
for big endian and then little, or vice versa.
Fix it by making tm-resched-dscr depend on pmu/lib.c, causing the code
to be built directly in, meaning no .o is generated.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Once in a while I see build errors similar to the following
when building images from a clean tree.
Building powerpc:virtex-ml507:44x/virtex5_defconfig ... failed
------------
Error log:
arch/powerpc/boot/treeboot-akebono.c:37:20: fatal error:
libfdt.h: No such file or directory
Building powerpc:bamboo:smpdev:44x/bamboo_defconfig ... failed
------------
Error log:
arch/powerpc/boot/treeboot-akebono.c:37:20: fatal error:
libfdt.h: No such file or directory
arch/powerpc/boot/treeboot-currituck.c:35:20: fatal error:
libfdt.h: No such file or directory
Rebuilds will succeed.
Turns out that several source files in arch/powerpc/boot/ include
libfdt.h, but Makefile dependencies are incomplete. Let's fix that.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
If multipathing is enabled, each NVMe subsystem creates a head
namespace (e.g., nvme0n1) and multiple private namespaces
(e.g., nvme0c0n1 and nvme0c1n1) in sysfs. When creating links for
private namespaces, links of head namespace are used, so the
namespace creation order must be followed (e.g., nvme0n1 ->
nvme0c1n1). If the order is not followed, links of sysfs will be
incomplete or kernel panic will occur.
The kernel panic was:
kernel BUG at fs/sysfs/symlink.c:27!
Call Trace:
nvme_mpath_add_disk_links+0x5d/0x80 [nvme_core]
nvme_validate_ns+0x5c2/0x850 [nvme_core]
nvme_scan_work+0x1af/0x2d0 [nvme_core]
Correct order
Context A Context B
nvme0n1
nvme0c0n1 nvme0c1n1
Incorrect order
Context A Context B
nvme0c1n1
nvme0n1
nvme0c0n1
The nvme_mpath_add_disk (for creating head namespace) is called
just before the nvme_mpath_add_disk_links (for creating private
namespaces). In nvme_mpath_add_disk, the first context acquires
the lock of subsystem and creates a head namespace, and other
contexts do nothing by checking GENHD_FL_UP of a head namespace
after waiting to acquire the lock. We verified the code with or
without multipathing using three vendors of dual-port NVMe SSDs.
Signed-off-by: Baegjae Sung <baegjae@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
|
|
Makes them easier to find.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
When LPE audio driver gets some error at probing, it may lead to a
crash because of canceling the pending work in hdmi_lpe_audio_free(),
since some of ports might be still not initialized.
For assuring the proper free of each port, initialize all ports at the
beginning of the probe.
Fixes: b4eb0d522fcb ("ALSA: x86: Split snd_intelhad into card and PCM specific structures")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The commit change for supporting the multiple ports moved involved
some code shuffling, and there the initializations of spinlock and
mutex in snd_intelhad object were dropped mistakenly.
This patch adds the missing initializations again for each port.
Fixes: b4eb0d522fcb ("ALSA: x86: Split snd_intelhad into card and PCM specific structures")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The patch "ALSA: control: code refactoring for ELEM_READ/ELEM_WRITE
operations" introduced a potential for kernel memory corruption due
to an incorrect if statement allowing non-readable controls to fall
through and call the get function. For TLV controls a driver can omit
SNDRV_CTL_ELEM_ACCESS_READ to ensure that only the TLV get function
can be called. Instead the normal get() can be invoked unexpectedly
and as the driver expects that this will only be called for controls
<= 512 bytes, potentially try to copy >512 bytes into the 512 byte
return array, so corrupting kernel memory.
The problem is an attempt to refactor the snd_ctl_elem_read function
to invert the logic so that it conditionally aborted if the control
is unreadable instead of conditionally executing. But the if statement
wasn't inverted correctly.
The correct inversion of
if (a && !b)
is
if (!a || b)
Fixes: becf9e5d553c2 ("ALSA: control: code refactoring for ELEM_READ/ELEM_WRITE operations")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
into drm-fixes
- Powerplay fixes for cards with no displays attached
- Couple of DC fixes
- radeon workaround for PPC64
* 'drm-fixes-4.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: insist on 32-bit DMA for Cedar on PPC64/PPC64LE
drm/amd/display: VGA black screen from s3 when attached to hook
drm/amdgpu: Unify the dm resume calls into one
drm/amdgpu: Add a missing lock for drm_mm_takedown
Revert "drm/radeon/pm: autoswitch power state when in balanced mode"
drm/amd/powerplay/smu7: allow mclk switching with no displays
drm/amd/powerplay/vega10: allow mclk switching with no displays
|
|
The ARM PMU doesn't have a reg address, so fix the following DTC warning
(requires W=1):
Node /soc/arm-pmu missing or empty reg/ranges property
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This patch fixes the following DTC warning (requires W=1):
Node /soc/local_intc simple-bus unit address format error, expected "40000000"
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Jon attempted to fix the amount of RAM on the BCM958625HR in commit
c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.
The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.
Fixes: c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
It seems that the proper value to return in this particular case is the
one contained into variable new_index instead of ret.
Addresses-Coverity-ID: 1465148 ("Copy-paste error")
Fixes: e46c7287b1c2 ("nbd: add a basic netlink interface")
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull seccomp fix from James Morris:
"This disables the seccomp samples when cross compiling.
We've seen too many build issues here, so it's best to just disable
it, especially since they're just the samples"
* 'fixes-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
samples/seccomp: do not compile when cross compiled
|
|
The Cinterion PL8 is an LTE modem with 2 possible WWAN interfaces.
The modem is controlled via AT commands through the exposed TTYs.
AT^SWWAN write command can be used to activate or deactivate a WWAN
connection for a PDP context defined with AT+CGDCONT. UE supports
two WWAN adapter. Both WWAN adapters can be activated a the same time
Signed-off-by: Bassem Boubaker <bassem.boubaker@actia.fr>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tls ulp overrides sk->prot with a new tls specific proto structs.
The tls specific structs were previously based on the ipv4 specific
tcp_prot sturct.
As a result, attaching the tls ulp to an ipv6 tcp socket replaced
some ipv6 callback with the ipv4 equivalents.
This patch adds ipv6 tls proto structs and uses them when
attached to ipv6 sockets.
Fixes: 3c4d7559159b ('tls: kernel TLS support')
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have uninlined the sh_eth_{read|write}() functions introduced in the
commit 4a55530f38e ("net: sh_eth: modify the definitions of register").
Now remove *inline* from sh_eth_tsu_{read|write}() as well and move
these functions from the header to the driver itself. This saves 684
more bytes of object code (ARM gcc 4.8.5)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Xin Long says:
====================
net: fix IFLA_MTU ignored on NEWLINK for some ip and ipv6 tunnels
The fix for ip_gre follows the way other ip tunnels do: not to
set mtu in ndo_init, as ip_tunnel_newlink will take care of it
properly.
The fix for ip6_tunnel and sit follows the way ipv6 tunenls do:
to set mtu again according to IFLA_MTU after, as all bind_dev
are called in ndo_init where it can't get the tb[IFLA_MTU].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 128bb975dc3c ("ip6_gre: init dev->mtu and dev->hard_header_len
correctly") fixed IFLA_MTU ignored on NEWLINK for ip6_gre. The same
mtu fix is also needed for sit.
Note that dev->hard_header_len setting for sit works fine, no need to
fix it. sit is actually ipv4 tunnel, it can't call ip6_tnl_change_mtu
to set mtu.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 128bb975dc3c ("ip6_gre: init dev->mtu and dev->hard_header_len
correctly") fixed IFLA_MTU ignored on NEWLINK for ip6_gre. The same
mtu fix is also needed for ip6_tunnel.
Note that dev->hard_header_len setting for ip6_tunnel works fine,
no need to fix it.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's safe to remove the setting of dev's needed_headroom and mtu in
__gre_tunnel_init, as discussed in [1], ip_tunnel_newlink can do it
properly.
Now Eric noticed that it could cover the mtu value set in do_setlink
when creating a ip_gre dev. It makes IFLA_MTU param not take effect.
So this patch is to remove them to make IFLA_MTU work, as in other
ipv4 tunnels.
[1]: https://patchwork.ozlabs.org/patch/823504/
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.")
Reported-by: Eric Garver <e@erig.me>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit f5e64032a799 ("net: phy: fix resume handling") changes the
locking semantics for phy_resume() such that the caller now needs to
hold the phy mutex. Not all call sites were adopted to this new
semantic, resulting in warnings from the added
WARN_ON(!mutex_is_locked(&phydev->lock)). Rather than change the
semantics, add a __phy_resume() and restore the old behavior of
phy_resume().
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: f5e64032a799 ("net: phy: fix resume handling")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux into fixes-v4.16-rc4
- do not build samples when cross compiling (Michal Hocko)
From Kees: "This disables the seccomp samples when cross compiling. We're seen too many build issues here, so
it's best to just disable it, especially since they're just the samples."
|
|
Use the right loop index, not the number of devices in the array that we
need to remove, the following message uncovered the problem:
[ 5437.044119] hook not found, pf 5 num 0
[ 5437.044140] WARNING: CPU: 2 PID: 24983 at net/netfilter/core.c:376 __nf_unregister_net_hook+0x250/0x280
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Kernel crashed when run fio in a RAID5 backend bcache device, the call
trace is bellow:
[ 440.012034] kernel BUG at block/blk-ioc.c:146!
[ 440.012696] invalid opcode: 0000 [#1] SMP NOPTI
[ 440.026537] CPU: 2 PID: 2205 Comm: md127_raid5 Not tainted 4.15.0 #8
[ 440.027441] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 07/16
/2015
[ 440.028615] RIP: 0010:put_io_context+0x8b/0x90
[ 440.029246] RSP: 0018:ffffa8c882b43af8 EFLAGS: 00010246
[ 440.029990] RAX: 0000000000000000 RBX: ffffa8c88294fca0 RCX: 0000000000
0f4240
[ 440.031006] RDX: 0000000000000004 RSI: 0000000000000286 RDI: ffffa8c882
94fca0
[ 440.032030] RBP: ffffa8c882b43b10 R08: 0000000000000003 R09: ffff949cb8
0c1700
[ 440.033206] R10: 0000000000000104 R11: 000000000000b71c R12: 00000000000
01000
[ 440.034222] R13: 0000000000000000 R14: ffff949cad84db70 R15: ffff949cb11
bd1e0
[ 440.035239] FS: 0000000000000000(0000) GS:ffff949cba280000(0000) knlGS:
0000000000000000
[ 440.060190] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 440.084967] CR2: 00007ff0493ef000 CR3: 00000002f1e0a002 CR4: 00000000001
606e0
[ 440.110498] Call Trace:
[ 440.135443] bio_disassociate_task+0x1b/0x60
[ 440.160355] bio_free+0x1b/0x60
[ 440.184666] bio_put+0x23/0x30
[ 440.208272] search_free+0x23/0x40 [bcache]
[ 440.231448] cached_dev_write_complete+0x31/0x70 [bcache]
[ 440.254468] closure_put+0xb6/0xd0 [bcache]
[ 440.277087] request_endio+0x30/0x40 [bcache]
[ 440.298703] bio_endio+0xa1/0x120
[ 440.319644] handle_stripe+0x418/0x2270 [raid456]
[ 440.340614] ? load_balance+0x17b/0x9c0
[ 440.360506] handle_active_stripes.isra.58+0x387/0x5a0 [raid456]
[ 440.380675] ? __release_stripe+0x15/0x20 [raid456]
[ 440.400132] raid5d+0x3ed/0x5d0 [raid456]
[ 440.419193] ? schedule+0x36/0x80
[ 440.437932] ? schedule_timeout+0x1d2/0x2f0
[ 440.456136] md_thread+0x122/0x150
[ 440.473687] ? wait_woken+0x80/0x80
[ 440.491411] kthread+0x102/0x140
[ 440.508636] ? find_pers+0x70/0x70
[ 440.524927] ? kthread_associate_blkcg+0xa0/0xa0
[ 440.541791] ret_from_fork+0x35/0x40
[ 440.558020] Code: c2 48 00 5b 41 5c 41 5d 5d c3 48 89 c6 4c 89 e7 e8 bb c2
48 00 48 8b 3d bc 36 4b 01 48 89 de e8 7c f7 e0 ff 5b 41 5c 41 5d 5d c3 <0f> 0b
0f 1f 00 0f 1f 44 00 00 55 48 8d 47 b8 48 89 e5 41 57 41
[ 440.610020] RIP: put_io_context+0x8b/0x90 RSP: ffffa8c882b43af8
[ 440.628575] ---[ end trace a1fd79d85643a73e ]--
All the crash issue happened when a bypass IO coming, in such scenario
s->iop.bio is pointed to the s->orig_bio. In search_free(), it finishes the
s->orig_bio by calling bio_complete(), and after that, s->iop.bio became
invalid, then kernel would crash when calling bio_put(). Maybe its upper
layer's faulty, since bio should not be freed before we calling bio_put(),
but we'd better calling bio_put() first before calling bio_complete() to
notify upper layer ending this bio.
This patch moves bio_complete() under bio_put() to avoid kernel crash.
[mlyle: fixed commit subject for character limits]
Reported-by: Matthias Ferdinand <bcache@mfedv.net>
Tested-by: Matthias Ferdinand <bcache@mfedv.net>
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 2831231d4c3f ("bcache: reduce cache_set devices iteration by
devices_max_used") adds c->devices_max_used to reduce iteration of
c->uuids elements, this value is updated in bcache_device_attach().
But for flash only volume, when calling flash_devs_run(), the function
bcache_device_attach() is not called yet and c->devices_max_used is not
updated. The unexpected result is, the flash only volume won't be run
by flash_devs_run().
This patch fixes the issue by iterate all c->uuids elements in
flash_devs_run(). c->devices_max_used will be updated properly when
bcache_device_attach() gets called.
[mlyle: commit subject edited for character limit]
Fixes: 2831231d4c3f ("bcache: reduce cache_set devices iteration by devices_max_used")
Reported-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull tpm fixes from James Morris:
"Bugfixes for TPM, from Jeremy Boone, via Jarkko Sakkinen"
* 'fixes-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: fix potential buffer overruns caused by bit glitches on the bus
tpm: st33zp24: fix potential buffer overruns caused by bit glitches on the bus
tpm_i2c_infineon: fix potential buffer overruns caused by bit glitches on the bus
tpm_i2c_nuvoton: fix potential buffer overruns caused by bit glitches on the bus
tpm_tis: fix potential buffer overruns caused by bit glitches on the bus
|
|
In commit 60c253069632 ("tipc: fix race between poll() and
setsockopt()") we introduced a pointer from struct tipc_group to the
'group_is_connected' flag in struct tipc_sock, so that this field can
be checked without dereferencing the group pointer of the latter struct.
The initial value for this flag is correctly set to 'false' when a
group is created, but we miss the case when no group is created at
all, in which case the initial value should be 'true'. This has the
effect that SOCK_RDM/DGRAM sockets sending datagrams never receive
POLLOUT if they request so.
This commit corrects this bug.
Fixes: 60c253069632 ("tipc: fix race between poll() and setsockopt()")
Reported-by: Hoang Le <hoang.h.le@dektek.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()"
accidentally broke cpufreq on s3c2410 and s3c2412.
These two platforms don't have a CPU frequency table and used to skip
calling cpufreq_table_validate_and_show() for them. But with the
above commit, we started calling it unconditionally and that will
eventually fail as the frequency table pointer is NULL.
Fix this by calling cpufreq_table_validate_and_show() conditionally
again.
Fixes: a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()"
Cc: 3.13+ <stable@vger.kernel.org> # v3.13+
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix resource coverity errors.
Fixes: d9f9b9a4d05f ("devlink: Add support for resource abstraction")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to RFC 1191 sections 3 and 4, ICMP frag-needed messages
indicating an MTU below 68 should be rejected:
A host MUST never reduce its estimate of the Path MTU below 68
octets.
and (talking about ICMP frag-needed's Next-Hop MTU field):
This field will never contain a value less than 68, since every
router "must be able to forward a datagram of 68 octets without
fragmentation".
Furthermore, by letting net.ipv4.route.min_pmtu be set to negative
values, we can end up with a very large PMTU when (-1) is cast into u32.
Let's also make ip_rt_min_pmtu a u32, since it's only ever compared to
unsigned ints.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2018-02-26
Here are a two Bluetooth driver fixes for the 4.16 kernel.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation checks the combined size of the children with
the 'size' of the parent. The correct behavior is to check the combined
size vs the pending change and to compare vs the 'size_new'.
Fixes: d9f9b9a4d05f ("devlink: Add support for resource abstraction")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Tested-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to R-Car Gen3 Rev.0.80 manual, the DMATCR can be set to
16,777,215 as maximum. So, this patch fixes the max_chunk_size for
safety on all of SoCs. Otherwise, a system may hang if the DMATCR
is set to 0 on R-Car Gen3.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
As the block layer, since the conversion to blkmq, claims the host using a
context, a following nested call to mmc_claim_host(), which isn't using a
context, may hang.
Calling mmc_interrupt_hpi() and mmc_read_bkops_status() via the mmc block
layer, may suffer from this problem, as these functions are calling
mmc_claim|release_host().
Let's fix the problem by removing the calls to mmc_claim|release_host()
from the above mentioned functions and instead make the callers responsible
of claiming/releasing the host. As a matter of fact, the existing callers
already deals with it.
Fixes: 81196976ed94 ("mmc: block: Add blk-mq support")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
|
|
cat /sys/kernel/debug/mmc0/regs will hang up the system since
it's in runtime suspended state, so the genpd and biu_clk is
off. This patch fixes this problem by calling pm_runtime_get_sync
to wake it up before reading the registers.
Fixes: e9ed8835e990 ("mmc: dw_mmc: add runtime PM callback")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add num_caps field for dw_mci_drv_data to validate the controller
id from DT alias and non-DT ways.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfccb3 ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
