| Age | Commit message (Collapse) | Author |
|---|
|
For T6, tid start range should be read from
LE_DB_ACTIVE_TABLE_START_INDEX_A register.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-12-18
Here's the first bluetooth-next pull request for the 4.16 kernel.
- hci_ll: multiple cleanups & fixes
- Remove Gustavo Padovan from the MAINTAINERS file
- Support BLE Adversing while connected (if the controller can do it)
- DT updates for TI chips
- Various other smaller cleanups & fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow the boot loader to specify the MAC address in the device tree
to override the EEPROM, or in case no EEPROM is present.
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Tristram Ha <tristram.ha@micrel.com>
Cc: David J. Choi <david.choi@micrel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now it's using IPV6_MIN_MTU as the min mtu in ip6_tnl_xmit, but
IPV6_MIN_MTU actually only works when the inner packet is ipv6.
With IPV6_MIN_MTU for ipv4 packets, the new pmtu for inner dst
couldn't be set less than 1280. It would cause tx_err and the
packet to be dropped when the outer dst pmtu is close to 1280.
Jianlin found it by running ipv4 traffic with the topo:
(client) gre6 <---> eth1 (route) eth2 <---> gre6 (server)
After changing eth2 mtu to 1300, the performance became very
low, or the connection was even broken. The issue also affects
ip4ip6 and ip6ip6 tunnels.
So if the inner packet is ipv4, 576 should be considered as the
min mtu.
Note that for ip4ip6 and ip6ip6 tunnels, the inner packet can
only be ipv4 or ipv6, but for gre6 tunnel, it may also be ARP.
This patch using 576 as the min mtu for non-ipv6 packet works
for all those cases.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same fix as the patch "ip_gre: remove the incorrect mtu limit for
ipgre tap" is also needed for ip6_gre.
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipgre tap driver calls ether_setup(), after commit 61e84623ace3
("net: centralize net_device min/max MTU checking"), the range
of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.
It causes the dev mtu of the ipgre tap device to not be greater
than 1500, this limit value is not correct for ipgre tap device.
Besides, it's .change_mtu already does the right check. So this
patch is just to set max_mtu as 0, and leave the check to it's
.change_mtu.
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unlike ip tunnels, now vxlan doesn't do any pmtu update for
upper dst pmtu, even if it doesn't match the lower dst pmtu
any more.
The problem can be reproduced when reducing the vxlan lower
dev's pmtu when running netperf. In jianlin's testing, the
performance went to 1/7 of the previous.
This patch is to update the upper dst pmtu to match the lower
dst pmtu on tx path so that packets can be sent out even when
lower dev's pmtu has been changed.
It also works for metadata dst.
Note that this patch doesn't process any pmtu icmp packet.
But even in the future, the support for pmtu icmp packets
process of udp tunnels will also needs this.
The same thing will be done for geneve in another patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under certain conditions EMAC stop reception of incoming packets and
continuously increment R_MISS register instead of saving data into
provided buffer. The commit implement workaround for such situation.
Then the stall detected EMAC will be restarted.
On device the stall looks like the device lost it's dynamic IP address.
ifconfig shows that interface error counter rapidly increments.
At the same time on the DHCP server we can see continues DHCP-requests
from device.
In real network stalls happen really rarely. To make them frequent the
broadcast storm[1] should be simulated. For simulation it is necessary
to make following connections:
1. connect radxarock to 1st port of switch
2. connect some PC to 2nd port of switch
3. connect two other free ports together using standard ethernet cable,
in order to make a switching loop.
After that, is necessary to make a broadcast storm. For example, running on
PC 'ping' to some IP address triggers ARP-request storm. After some
time (~10sec), EMAC on rk3188 will stall.
Observed and tested on rk3188 radxarock.
[1] https://en.wikipedia.org/wiki/Broadcast_radiation
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
arc_emac_rx() has some issues found by code review.
In case netdev_alloc_skb_ip_align() or dma_map_single() failure
rx fifo entry will not be returned to EMAC.
In case dma_map_single() failure previously allocated skb became
lost to driver. At the same time address of newly allocated skb
will not be provided to EMAC.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current solution would setup fixed and force link of 1Gbps to the both
GMAC on the default. However, The GMAC should always be put to link down
state when the GMAC is disabled on certain target boards. Otherwise,
the driver possibly receives unexpected data from the floating hardware
connection through the unused GMAC. Although the driver had been added
certain protection in RX path to get rid of such kind of unexpected data
sent to the upper stack.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A few thousand such pages are usually left around due to the re-use of
L1 tables having been provided by the hypervisor (Dom0) or tool stack
(DomU). Set NX in the direct map variant, which needs to be done in L2
due to the dual use of the re-used L1s.
For x86_configure_nx() to actually do what it is supposed to do, call
get_cpu_cap() first. This was broken by commit 4763ed4d45 ("x86, mm:
Clean up and simplify NX enablement") when switching away from the
direct EFER read.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
This reverts commit 63dd00fa3e524c27cc0509190084ab147ecc8ae2.
RAUHT DELETE_ALL seems to trigger a bug in FW. That manifests by later
calls to RAUHT ADD of an IPv6 neighbor to fail with "bad parameter"
error code.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Fixes: 63dd00fa3e52 ("mlxsw: spectrum_router: Add batch neighbour deletion")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jonas Gorski says:
====================
bcm63xx_enet: remove mac_id usage
This patchset aims at reducing the platform device id number usage with
the target of making it eventually possible to probe the driver through OF.
Runtested on BCM6358.
Since the patches touch mostly net/, they should go through net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Directly use the platform device for generating the miibus name. This
removes the last user of bcm_enet_priv::mac_id and we can remove the
field.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enabling the ephy clock for mac 1 is harmless, and the actual usage of
the ephy is not restricted to mac 0, so we might as well remove the
check.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To reduce the reliance on device ids, pass the dma channel numbers to
the enet devices as platform data.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have the individual clocks available as "enet" we
don't need to rely on the device id for them anymore.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Haishuang Yan says:
====================
net: speedup geneve/vxlan tunnels dismantle
This patch series add batching to vxlan/geneve tunnels so that netns
dismantles are less costly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we now hold RTNL lock in geneve_exit_net, it's better batch them
to speedup geneve tunnel dismantle.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we now hold RTNL lock in vxlan_exit_net, it's better to batch them
to speedup vxlan tunnels dismantle.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since both first_tx_ctx and tx_skb are the head of tx ctx, it not
necessary to use two structure members to statically indicate
the head of tx ctx. So first_tx_ctx is removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michael Chan says:
====================
Introduce NETIF_F_GRO_HW
Introduce NETIF_F_GRO_HW feature flag and convert drivers that support
hardware GRO to use the new flag.
v5:
- Documentation changes requested by Alexander Duyck.
- bnx2x changes requested by Manish Chopra to enable LRO by default, and
disable GRO_HW if disable_tpa module parameter is set.
v4:
- more changes requested by Alexander Duyck:
- check GRO_HW/GRO dependency in drivers's ndo_fix_features().
- Reverse the order of RXCSUM and GRO_HW dependency check in
netdev_fix_features().
- No propagation in netdev_disable_gro_hw().
v3:
- Let driver's ndo_fix_features() disable NETIF_F_LRO when NETIF_F_GRO_HW
is set instead of doing it in common netdev_fix_features().
v2:
- NETIF_F_GRO_HW flag propagation between upper and lower devices not
required (see patch 1).
- NETIF_F_GRO_HW depends on NETIF_F_GRO and NETIF_F_RXCSUM.
- Add dev_disable_gro_hw() to disable GRO_HW for generic XDP.
- Use ndo_fix_features() on all 3 drivers to drop GRO_HW when it is not
supported
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Advertise NETIF_F_GRO_HW and set edev->gro_disable according to the
feature flag. Add qede_fix_features() to drop NETIF_F_GRO_HW if
XDP is running or MTU does not support GRO_HW or GRO is not set.
qede_change_mtu() also checks and disables GRO_HW if MTU is not
supported.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Acked-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Advertise NETIF_F_GRO_HW and turn on TPA_MODE_GRO when NETIF_F_GRO_HW
is set. Disable NETIF_F_GRO_HW in bnx2x_fix_features() if the MTU
does not support TPA_MODE_GRO or GRO is not set. bnx2x_change_mtu() also
needs to disable NETIF_F_GRO_HW if the MTU does not support it.
Original parameter disable_tpa will continue to disable LRO and GRO_HW.
Preserve the original behavior of enabling LRO by default. User has
to run ethtool -K to explicitly enable GRO_HW.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Advertise NETIF_F_GRO_HW in hw_features if hardware GRO is supported.
In bnxt_fix_features(), disable GRO_HW and LRO if current hardware
configuration does not allow it. GRO_HW depends on GRO. GRO_HW is
also mutually exclusive with LRO. XDP setup will now rely on
bnxt_fix_features() to turn off aggregation. During chip init, turn on
or off hardware GRO based on NETIF_F_GRO_HW in features flag.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware should not aggregate any packets when generic XDP is installed.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce NETIF_F_GRO_HW feature flag for NICs that support hardware
GRO. With this flag, we can now independently turn on or off hardware
GRO when GRO is on. Previously, drivers were using NETIF_F_GRO to
control hardware GRO and so it cannot be independently turned on or
off without affecting GRO.
Hardware GRO (just like GRO) guarantees that packets can be re-segmented
by TSO/GSO to reconstruct the original packet stream. Logically,
GRO_HW should depend on GRO since it a subset, but we will let
individual drivers enforce this dependency as they see fit.
Since NETIF_F_GRO is not propagated between upper and lower devices,
NETIF_F_GRO_HW should follow suit since it is a subset of GRO. In other
words, a lower device can independent have GRO/GRO_HW enabled or disabled
and no feature propagation is required. This will preserve the current
GRO behavior. This can be changed later if we decide to propagate GRO/
GRO_HW/RXCSUM from upper to lower devices.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a hang issue seen when changing the MTU size from 1500 MTU
to 9000 MTU on both 5717 and 5719 chips. In discussion with Broadcom,
they've indicated that these chipsets have the same phy as the 57766
chipset, so the same workarounds apply. This has been tested by IBM
on both Power 8 and Power 9 systems as well as by Broadcom on x86
hardware and has been confirmed to resolve the hang issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_PROC_FS is disabled, we will not use the prot_inuse
counter. This adds an #ifdef to hide the variable definition in
that case. This is not a bugfix. But we can save bytes when there
are many network namespace.
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Martin Zhang <zhangjunweimartin@didichuxing.com>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some case, we want to know how many sockets are in use in
different _net_ namespaces. It's a key resource metric.
This patch add a member in struct netns_core. This is a counter
for socket-inuse in the _net_ namespace. The patch will add/sub
counter in the sk_alloc, sk_clone_lock and __sk_free.
This patch will not counter the socket created in kernel.
It's not very useful for userspace to know how many kernel
sockets we created.
The main reasons for doing this are that:
1. When linux calls the 'do_exit' for process to exit, the functions
'exit_task_namespaces' and 'exit_task_work' will be called sequentially.
'exit_task_namespaces' may have destroyed the _net_ namespace, but
'sock_release' called in 'exit_task_work' may use the _net_ namespace
if we counter the socket-inuse in sock_release.
2. socket and sock are in pair. More important, sock holds the _net_
namespace. We counter the socket-inuse in sock, for avoiding holding
_net_ namespace again in socket. It's a easy way to maintain the code.
Signed-off-by: Martin Zhang <zhangjunweimartin@didichuxing.com>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the member name will make the code more readable.
This patch will be used in next patch.
Signed-off-by: Martin Zhang <zhangjunweimartin@didichuxing.com>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
One fix for ulpi-node lookup at msm glue driver
|
|
Use the direction argument passed into begin_cpu_access
and end_cpu_access when calling the dma_sync_sg_for_cpu/device.
The actual cache primitive called depends on the direction
passed in.
Signed-off-by: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In trying to add support for drm_hwcomposer to HiKey,
I've needed to utilize the ION CMA heap, and I've noticed
problems with allocations on newer kernels failing.
It seems back with 204f672255c2 ("ion: Use CMA APIs directly"),
the ion_cma_heap code was modified to use the CMA API, but
kept the arguments as buffer lengths rather then number of pages.
This results in errors as we don't have enough pages in CMA to
satisfy the exaggerated requests.
This patch converts the ion_cma_heap CMA API usage to properly
request pages.
It also fixes a minor issue in the allocation where in the error
path, the cma_release is called with the buffer->size value which
hasn't yet been set.
Cc: Laura Abbott <labbott@redhat.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dmitry Shmidt <dimitrysh@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Amit Pundir <amit.pundir@linaro.org>
Fixes: 204f672255c2 ("staging: android: ion: Use CMA APIs directly")
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few more fixes:
* hwsim:
- set To-DS bit in some frames missing it
- fix sleeping in atomic
* nl80211:
- doc cleanup
- fix locking in an error path
* build:
- don't append to created certs C files
- ship certificate pre-hexdumped
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Deadlock during cgroup migration from cpu hotplug path when a task T is
being moved from source to destination cgroup.
kworker/0:0
cpuset_hotplug_workfn()
cpuset_hotplug_update_tasks()
hotplug_update_tasks_legacy()
remove_tasks_in_empty_cpuset()
cgroup_transfer_tasks() // stuck in iterator loop
cgroup_migrate()
cgroup_migrate_add_task()
In cgroup_migrate_add_task() it checks for PF_EXITING flag of task T.
Task T will not migrate to destination cgroup. css_task_iter_start()
will keep pointing to task T in loop waiting for task T cg_list node
to be removed.
Task T
do_exit()
exit_signals() // sets PF_EXITING
exit_task_namespaces()
switch_task_namespaces()
free_nsproxy()
put_mnt_ns()
drop_collected_mounts()
namespace_unlock()
synchronize_rcu()
_synchronize_rcu_expedited()
schedule_work() // on cpu0 low priority worker pool
wait_event() // waiting for work item to execute
Task T inserted a work item in the worklist of cpu0 low priority
worker pool. It is waiting for expedited grace period work item
to execute. This work item will only be executed once kworker/0:0
complete execution of cpuset_hotplug_workfn().
kworker/0:0 ==> Task T ==>kworker/0:0
In case of PF_EXITING task being migrated from source to destination
cgroup, migrate next available task in source cgroup.
Signed-off-by: Prateek Sood <prsood@codeaurora.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
In case we have multiple modesets for different connectors
happening in parallel we could have a race on the RMW on these
shared registers.
This possibility was initially raised by Paulo when reviewing
commit '555e38d27317 ("drm/i915/cnl: DDI - PLL mapping")'
but the original possibility comes from commit '5416d871136d
("drm/i915/skl: Set the eDP link rate on DPLL0")'. Or maybe
later when atomic commits entered into picture.
Apparently the discussion around this topic showed that the
right solution would be on serializing the atomic commits in
a way that we don't have the possibility of races here since
if that parallel modeset happenings apparently many other
things will be on fire.
Code is there since SKL and there was no report of issue,
but since we never looked back to that serialization possibility,
and also we don't have an igt case for that it is better to at
least protect this corner.
Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Fixes: 555e38d27317 ("drm/i915/cnl: DDI - PLL mapping")
Fixes: 5416d871136d ("drm/i915/skl: Set the eDP link rate on DPLL0")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst maarten.lankhorst@linux.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst maarten.lankhorst@linux.intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20171215224310.19103-1-rodrigo.vivi@intel.com
(cherry picked from commit 8edcda1266f93816fde77c9754f388ae0ae343fc)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Just printk the string, or at least do not double up on the newlines!
Fixes: eef57324d926 ("drm/i915: setup bridge for HDMI LPE audio driver")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Jerome Anand <jerome.anand@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213182858.2159-1-chris@chris-wilson.co.uk
(cherry picked from commit 99cd05c43baac8ef56c20eb1776a15b02c81ccc3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
If an rt5514-spi device is probed but the platform hasn't linked it in,
we might never fully request the SPI IRQ, nor configure the rt5514 DSP,
but we still might try to enable the SPI IRQ (enable_irq_wake()). This
is bad, and among other things, can cause the interrupt to trigger every
time we try to suspend the system (e.g., because the interrupt trigger
setting was never set properly).
Instead of setting our wakeup capabilities in the SPI driver probe
routine, let's wait until we've actually requested the IRQ.
Fixes issues seen on the "kevin" Chromebook (Samsung Chromebook Plus).
Fixes: 58f1c07d23cd ("ASoC: rt5514: Voice wakeup support.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'spi/fix/doc', 'spi/fix/imx', 'spi/fix/rspi', 'spi/fix/sun4i' and 'spi/fix/xilinx' into spi-linus
|
|
In skylake platform, we hear a loud pop noise(0 dB) at start of
audio capture power up sequence. This patch removes the pop noise
from the recording by adding a delay before enabling ADC.
Signed-off-by: Abhijeet Kumar <abhijeet.kumar@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 8e55b6fd0660 ("staging: lustre: lnet: replace list_for_each
with list_for_each_entry") was intended to be an idempotent change,
but actually broke the behavior of ksocknal_add_peer() causing mounts to fail.
The fact that it caused an existing "route2 = NULL;" to become
redundant could have been a clue. The fact that the loop body
set the new loop variable to NULL might also have been a clue
The original code relied on "route2" being NULL if nothing was found.
The new code would always set route2 to a non-NULL value if the list
was empty, and would likely crash if the list was not empty.
Restore correct functionality by using code-flow rather the value of
"route2" to determine whether to use on old route, or to add a new one.
Fixes: 8e55b6fd0660 ("staging: lustre: lnet: replace list_for_each with list_for_each_entry")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit e0429362ab15
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
There is one more model that has the same issue - C925e, so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This modem needs this quirk to operate. It produces timeouts when
resumed without reset.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usbip bind writes commands followed by random string when writing to
match_busid attribute in sysfs, caused by using full variable size
instead of string length.
Signed-off-by: Juan Zea <juan.zea@qindel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the following static checker warnings:
The patch c6688ef9f297: "usbip: fix stub_rx: harden CMD_SUBMIT path
to handle malicious input" from Dec 7, 2017, leads to the following
static checker warning:
drivers/usb/usbip/stub_rx.c:346 get_pipe()
warn: impossible condition
'(pdu->u.cmd_submit.transfer_buffer_length > ((~0 >> 1))) =>
(s32min-s32max > s32max)'
drivers/usb/usbip/stub_rx.c:486 stub_recv_cmd_submit()
warn: always true condition
'(pdu->u.cmd_submit.transfer_buffer_length <= ((~0 >> 1))) =>
(s32min-s32max <= s32max)'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usbip driver is leaking socket pointer address in messages. Remove
the messages that aren't useful and print sockfd in the ones that
are useful for debugging.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove and/or change debug, info. and error messages to not print
kernel pointer addresses.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove and/or change debug, info. and error messages to not print
kernel pointer addresses.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB 3.1 devices are not detected as 3.1 capable since 4.15-rc3 due to a
off by one in commit 81cf4a45360f ("USB: core: Add type-specific length
check of BOS descriptors")
It uses USB_DT_USB_SSP_CAP_SIZE() to get SSP capability size which takes
the zero based SSAC as argument, not the actual count of sublink speed
attributes.
USB3 spec 9.6.2.5 says "The number of Sublink Speed Attributes = SSAC + 1."
The type-specific length check patch was added to stable and needs to be
fixed there as well
Fixes: 81cf4a45360f ("USB: core: Add type-specific length check of BOS descriptors")
Cc: linux-stable <stable@vger.kernel.org>
CC: Masakazu Mokuno <masakazu.mokuno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
