| Age | Commit message (Collapse) | Author |
|---|
|
NAND chips require a bit of time to take the NAND operation into
account and set the BUSY bit in the STATUS reg. Make sure we don't poll
the STATUS reg too early in nand_soft_waitrdy().
Fixes: 8878b126df76 ("mtd: nand: add ->exec_op() implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Two nouveau crasher/deadlock fixes.
* 'linux-4.17' of git://github.com/skeggsb/linux:
drm/nouveau: Fix deadlock in nv50_mstm_register_connector()
drm/nouveau/ttm: don't dereference nvbo::cli, it can outlive client
|
|
Currently; we're grabbing all of the modesetting locks before adding MST
connectors to fbdev. This isn't actually necessary, and causes a
deadlock as well:
======================================================
WARNING: possible circular locking dependency detected
4.17.0-rc3Lyude-Test+ #1 Tainted: G O
------------------------------------------------------
kworker/1:0/18 is trying to acquire lock:
00000000c832f62d (&helper->lock){+.+.}, at: drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper]
but task is already holding lock:
00000000942e28e2 (crtc_ww_class_mutex){+.+.}, at: drm_modeset_backoff+0x8e/0x1c0 [drm]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (crtc_ww_class_mutex){+.+.}:
ww_mutex_lock+0x43/0x80
drm_modeset_lock+0x71/0x130 [drm]
drm_helper_probe_single_connector_modes+0x7d/0x6b0 [drm_kms_helper]
drm_setup_crtcs+0x15e/0xc90 [drm_kms_helper]
__drm_fb_helper_initial_config_and_unlock+0x29/0x480 [drm_kms_helper]
nouveau_fbcon_init+0x138/0x1a0 [nouveau]
nouveau_drm_load+0x173/0x7e0 [nouveau]
drm_dev_register+0x134/0x1c0 [drm]
drm_get_pci_dev+0x8e/0x160 [drm]
nouveau_drm_probe+0x1a9/0x230 [nouveau]
pci_device_probe+0xcd/0x150
driver_probe_device+0x30b/0x480
__driver_attach+0xbc/0xe0
bus_for_each_dev+0x67/0x90
bus_add_driver+0x164/0x260
driver_register+0x57/0xc0
do_one_initcall+0x4d/0x323
do_init_module+0x5b/0x1f8
load_module+0x20e5/0x2ac0
__do_sys_finit_module+0xb7/0xd0
do_syscall_64+0x60/0x1b0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
-> #2 (crtc_ww_class_acquire){+.+.}:
drm_helper_probe_single_connector_modes+0x58/0x6b0 [drm_kms_helper]
drm_setup_crtcs+0x15e/0xc90 [drm_kms_helper]
__drm_fb_helper_initial_config_and_unlock+0x29/0x480 [drm_kms_helper]
nouveau_fbcon_init+0x138/0x1a0 [nouveau]
nouveau_drm_load+0x173/0x7e0 [nouveau]
drm_dev_register+0x134/0x1c0 [drm]
drm_get_pci_dev+0x8e/0x160 [drm]
nouveau_drm_probe+0x1a9/0x230 [nouveau]
pci_device_probe+0xcd/0x150
driver_probe_device+0x30b/0x480
__driver_attach+0xbc/0xe0
bus_for_each_dev+0x67/0x90
bus_add_driver+0x164/0x260
driver_register+0x57/0xc0
do_one_initcall+0x4d/0x323
do_init_module+0x5b/0x1f8
load_module+0x20e5/0x2ac0
__do_sys_finit_module+0xb7/0xd0
do_syscall_64+0x60/0x1b0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
-> #1 (&dev->mode_config.mutex){+.+.}:
drm_setup_crtcs+0x10c/0xc90 [drm_kms_helper]
__drm_fb_helper_initial_config_and_unlock+0x29/0x480 [drm_kms_helper]
nouveau_fbcon_init+0x138/0x1a0 [nouveau]
nouveau_drm_load+0x173/0x7e0 [nouveau]
drm_dev_register+0x134/0x1c0 [drm]
drm_get_pci_dev+0x8e/0x160 [drm]
nouveau_drm_probe+0x1a9/0x230 [nouveau]
pci_device_probe+0xcd/0x150
driver_probe_device+0x30b/0x480
__driver_attach+0xbc/0xe0
bus_for_each_dev+0x67/0x90
bus_add_driver+0x164/0x260
driver_register+0x57/0xc0
do_one_initcall+0x4d/0x323
do_init_module+0x5b/0x1f8
load_module+0x20e5/0x2ac0
__do_sys_finit_module+0xb7/0xd0
do_syscall_64+0x60/0x1b0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
-> #0 (&helper->lock){+.+.}:
__mutex_lock+0x70/0x9d0
drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper]
nv50_mstm_register_connector+0x2c/0x50 [nouveau]
drm_dp_add_port+0x2f5/0x420 [drm_kms_helper]
drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper]
drm_dp_add_port+0x33f/0x420 [drm_kms_helper]
drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper]
drm_dp_check_and_send_link_address+0x87/0xd0 [drm_kms_helper]
drm_dp_mst_link_probe_work+0x4d/0x80 [drm_kms_helper]
process_one_work+0x20d/0x650
worker_thread+0x3a/0x390
kthread+0x11e/0x140
ret_from_fork+0x3a/0x50
other info that might help us debug this:
Chain exists of:
&helper->lock --> crtc_ww_class_acquire --> crtc_ww_class_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(crtc_ww_class_mutex);
lock(crtc_ww_class_acquire);
lock(crtc_ww_class_mutex);
lock(&helper->lock);
*** DEADLOCK ***
5 locks held by kworker/1:0/18:
#0: 000000004a05cd50 ((wq_completion)"events_long"){+.+.}, at: process_one_work+0x187/0x650
#1: 00000000601c11d1 ((work_completion)(&mgr->work)){+.+.}, at: process_one_work+0x187/0x650
#2: 00000000586ca0df (&dev->mode_config.mutex){+.+.}, at: drm_modeset_lock_all+0x3a/0x1b0 [drm]
#3: 00000000d3ca0ffa (crtc_ww_class_acquire){+.+.}, at: drm_modeset_lock_all+0x44/0x1b0 [drm]
#4: 00000000942e28e2 (crtc_ww_class_mutex){+.+.}, at: drm_modeset_backoff+0x8e/0x1c0 [drm]
stack backtrace:
CPU: 1 PID: 18 Comm: kworker/1:0 Tainted: G O 4.17.0-rc3Lyude-Test+ #1
Hardware name: Gateway FX6840/FX6840, BIOS P01-A3 05/17/2010
Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
Call Trace:
dump_stack+0x85/0xcb
print_circular_bug.isra.38+0x1ce/0x1db
__lock_acquire+0x128f/0x1350
? lock_acquire+0x9f/0x200
? lock_acquire+0x9f/0x200
? __ww_mutex_lock.constprop.13+0x8f/0x1000
lock_acquire+0x9f/0x200
? drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper]
? drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper]
__mutex_lock+0x70/0x9d0
? drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper]
? ww_mutex_lock+0x43/0x80
? _cond_resched+0x15/0x30
? ww_mutex_lock+0x43/0x80
? drm_modeset_lock+0xb2/0x130 [drm]
? drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper]
drm_fb_helper_add_one_connector+0x2a/0x60 [drm_kms_helper]
nv50_mstm_register_connector+0x2c/0x50 [nouveau]
drm_dp_add_port+0x2f5/0x420 [drm_kms_helper]
? mark_held_locks+0x50/0x80
? kfree+0xcf/0x2a0
? drm_dp_check_mstb_guid+0xd6/0x120 [drm_kms_helper]
? trace_hardirqs_on_caller+0xed/0x180
? drm_dp_check_mstb_guid+0xd6/0x120 [drm_kms_helper]
drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper]
drm_dp_add_port+0x33f/0x420 [drm_kms_helper]
? nouveau_connector_aux_xfer+0x7c/0xb0 [nouveau]
? find_held_lock+0x2d/0x90
? drm_dp_dpcd_access+0xd9/0xf0 [drm_kms_helper]
? __mutex_unlock_slowpath+0x3b/0x280
? drm_dp_dpcd_access+0xd9/0xf0 [drm_kms_helper]
drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper]
drm_dp_check_and_send_link_address+0x87/0xd0 [drm_kms_helper]
drm_dp_mst_link_probe_work+0x4d/0x80 [drm_kms_helper]
process_one_work+0x20d/0x650
worker_thread+0x3a/0x390
? process_one_work+0x650/0x650
kthread+0x11e/0x140
? kthread_create_worker_on_cpu+0x50/0x50
ret_from_fork+0x3a/0x50
Taking example from i915, the only time we need to hold any modesetting
locks is when changing the port on the mstc, and in that case we only
need to hold the connection mutex.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Potentially responsible for some random OOPSes.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org [v4.15+]
|
|
into drm-fixes
A little bigger than normal since this is two weeks of fixes.
- Atom firmware table updates for vega12
- Fix fallout from huge page support
- Fix up smu7 power profile interface to be consistent with vega
- Misc other fixes
* 'drm-fixes-4.17' of git://people.freedesktop.org/~agd5f/linux:
drm/amd/pp: Refine the output of pp_power_profile_mode on VI
drm/amdgpu: Switch to interruptable wait to recover from ring hang.
drm/ttm: Use GFP_TRANSHUGE_LIGHT for allocating huge pages
drm/amd/display: Use kvzalloc for potentially large allocations
drm/amd/display: Don't return ddc result and read_bytes in same return value
drm/amd/display: Add get_firmware_info_v3_2 for VG12
drm/amd: Add BIOS smu_info v3_3 required struct def.
drm/amd/display: Add VG12 ASIC IDs
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
atomic: Clear state pointers on clear (Ville)
vc4: Fix oops in dpi disable (Eric)
omap: Various error-checking + uninitialized var fixes (Tomi)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
* tag 'drm-misc-fixes-2018-05-09' of git://anongit.freedesktop.org/drm/drm-misc:
drm/vc4: Fix scaling of uni-planar formats
drm/bridge/sii8620: add Kconfig dependency on extcon
drm/omap: handle alloc failures in omap_connector
drm/omap: add missing linefeeds to prints
drm/omap: handle error if scale coefs are not found
drm/omap: check return value from soc_device_match
drm/omap: fix possible NULL ref issue in tiler_reserve_2d
drm/omap: fix uninitialized ret variable
drm/omap: silence unititialized variable warning
drm/vc4: Fix oops dereferencing DPI's connector since panel_bridge.
drm/atomic: Clean private obj old_state/new_state in drm_atomic_state_default_clear()
drm/atomic: Clean old_state/new_state in drm_atomic_state_default_clear()
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Increase LVDS panel timeout to 5s to avoid spurious *ERROR*
- Fix 2 WARNS: BIOS framebuffer related (FDO #105992) and eDP cdclk mismatch
* tag 'drm-intel-fixes-2018-05-09' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Fix drm:intel_enable_lvds ERROR message in kernel log
drm/i915: Correctly populate user mode h/vdisplay with pipe src size during readout
drm/i915: Adjust eDP's logical vco in a reliable place.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Fixup pagefault issue of mixer driver
- it makes sure to check shadow register for interlace scan.
- it corrects chroma_addr[1], height and vertical position values.
And trivial cleanup
- it just removes duplicated drm_bridge_attach.
* tag 'exynos-drm-fixes-for-v4.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: hdmi: avoid duplicating drm_bridge_attach
drm/exynos: mixer: avoid Oops in vp_video_buffer()
drm/exynos/mixer: fix synchronization check in interlaced mode
|
|
Both ‘uninorth_remove_memory’ and ‘null_cache_flush’ can be made
static. So make them.
Silence the following gcc warning (W=1):
drivers/char/agp/uninorth-agp.c:198:5: warning: no previous prototype for ‘uninorth_remove_memory’ [-Wmissing-prototypes]
and
drivers/char/agp/uninorth-agp.c:473:6: warning: no previous prototype for ‘null_cache_flush’ [-Wmissing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Exynos Scaler is a hardware module, which processes graphic data fetched
from memory and transfers the resultant dato another memory buffer.
Graphics data can be up/down-scaled, rotated, flipped and converted color
space. Scaler hardware modules are a part of Exynos5420 and newer Exynos
SoCs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch adapts Exynos DRM FIMC driver to new IPP v2 core API.
The side effect of this conversion is a switch to driver component API
to register properly in the Exynos DRM core.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Merge conflict so merged manually.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch adapts Exynos DRM GScaler driver to new IPP v2 core API.
The side effect of this conversion is a switch to driver component API
to register properly in the Exynos DRM core. During the conversion
driver has been adapted to support more specific compatible strings
to distinguish between Exynos5250 and Exynos5420 (different hardware
limits). Support for Exynos5433 variant has been added too
(different limits table, removed dependency on ARCH_EXYNOS5).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch adapts Exynos DRM rotator driver to new IPP v2 core API.
The side effect of this conversion is a switch to driver component API
to register properly in the Exynos DRM core.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch adds Exynos IPP v2 subsystem and userspace API.
New userspace API is focused ONLY on memory-to-memory image processing.
The two remainging operation modes of obsolete IPP v1 API (framebuffer
writeback and local-path output with image processing) can be implemented
using standard DRM features: writeback connectors and additional DRM planes
with scaling features.
V2 IPP userspace API is based on stateless approach, which much better fits
to memory-to-memory image processing model. It also provides support for
all image formats, which are both already defined in DRM API and supported
by the existing IPP hardware modules.
The API consists of the following ioctls:
- DRM_IOCTL_EXYNOS_IPP_GET_RESOURCES: to enumerate all available image
processing modules,
- DRM_IOCTL_EXYNOS_IPP_GET_CAPS: to query capabilities and supported image
formats of given IPP module,
- DRM_IOCTL_EXYNOS_IPP_GET_LIMITS: to query hardware limitiations for
selected image format of given IPP module,
- DRM_IOCTL_EXYNOS_IPP_COMMIT: to perform operation described by the
provided structures (source and destination buffers, operation rectangle,
transformation, etc).
The proposed userspace API is extensible. In the future more advanced image
processing operations can be defined to support for example blending.
Userspace API is fully functional also on DRM render nodes, so it is not
limited to the root/privileged client.
Internal driver API also has been completely rewritten. New IPP core
performs all possible input validation, checks and object life-time
control. The drivers can focus only on writing configuration to hardware
registers. Stateless nature of DRM_IOCTL_EXYNOS_IPP_COMMIT ioctl simplifies
the driver API. Minimal driver needs to provide a single callback for
starting processing and an array with supported image formats.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Merge conflict so merged manually.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- quirk for Toshiba Click Mini L9W-B, from Hans de Goede
- intel-ish-hid and wacom error handling (device freeing) path fixes
from Arvind Yadav
- memory corruption fix in intel-ish-hid driver from Hans de Goede
- a few new device ID additions to hid-lenovo from Peter Ganzhorn
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: i2c-hid: Add RESEND_REPORT_DESCR quirk for Toshiba Click Mini L9W-B
HID: intel-ish-hid: use put_device() instead of kfree()
HID: intel_ish-hid: Stop using a static local buffer in get_report()
HID: intel_ish-hid: Move header size check to inside the loop
HID: wacom: Release device resource data obtained by devres_alloc()
HID: lenovo: Add support for IBM/Lenovo Scrollpoint mice
|
|
In order to keep consist with Vega,
the output format of the pp_power_profile_mode would be
<integer><mode name string>< “*” for current profile>:"detail settings"
and remove the "CURRENT" mode line.
for example:
NUM MODE_NAME SCLK_UP_HYST SCLK_DOWN_HYST SCLK_ACTIVE_LEVEL MCLK_UP_HYST MCLK_DOWN_HYST MCLK_ACTIVE_LEVEL
0 3D_FULL_SCREEN: 0 100 30 0 100 10
1 POWER_SAVING: 10 0 30 - - -
2 VIDEO: - - - 10 16 31
3 VR: 0 11 50 0 100 10
4 COMPUTE: 0 5 30 - - -
5 CUSTOM *: 0 5 30 0 100 10
NUM MODE_NAME SCLK_UP_HYST SCLK_DOWN_HYST SCLK_ACTIVE_LEVEL MCLK_UP_HYST MCLK_DOWN_HYST MCLK_ACTIVE_LEVEL
0 3D_FULL_SCREEN: 0 100 30 0 100 10
1 POWER_SAVING *: 10 0 30 0 100 10
2 VIDEO: - - - 10 16 31
3 VR: 0 11 50 0 100 10
4 COMPUTE: 0 5 30 - - -
5 CUSTOM: - - - - - -
Reviewed-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
v2:
Use dma_fence_wait instead of dma_fence_wait_timeout(...,MAX_SCHEDULE_TIMEOUT)
Avoid printing error message for ERESTARTSYS
Originally-by: David Panariti <David.Panariti@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
GFP_TRANSHUGE tries very hard to allocate huge pages, which can result
in long delays with high memory pressure. I have observed firefox
freezing for up to around a minute due to this while restic was taking
a full system backup.
Since we don't really need huge pages, use GFP_TRANSHUGE_LIGHT |
__GFP_NORETRY instead, in order to fail quickly when there are no huge
pages available.
Set __GFP_KSWAPD_RECLAIM as well, in order for huge pages to be freed
up in the background if necessary.
With these changes, I'm no longer seeing freezes during a restic backup.
Cc: stable@vger.kernel.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Allocating up to 32 physically contiguous pages can easily fail (and has
failed for me), and isn't necessary anyway.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The two ranges overlap.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This fixes setting the clock divider on the TI OMAP-L138 LCDK board.
The clock drivers for OMAP-L138 are being covernted to the common clock
framework. When this happens, clk_set_rate() will no longer return an
error. However, on this SoC, the clock rate cannot actually be changed
because the clock has to maintain a fixed ratio to the ARM clock. So
after attempting to set the clock rate, we need to check to see if the
new rate is actually close enough. If not, then follow the previous
error path to adjust the divider in LCDC IP block to compensate for not
being able to change the parent clock rate.
Tested working on a TI OMAP-L138 LCDK board.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
|
|
As per listxattr(2):
On success, a nonnegative number is returned indicating the size
of the extended attribute name list. On failure, -1 is returned
and errno is set appropriately.
In SMB1, when the server returns an empty EA list through a listxattr(),
it will correctly return 0 as there are no EAs for the given file.
However, in SMB2+, it returns -ENODATA in listxattr() which is wrong since
the request and response were sent successfully, although there's no actual
EA for the given file.
This patch fixes listxattr() for SMB2+ by returning 0 in cifs_listxattr()
when the server returns an empty list of EAs.
Signed-off-by: Paulo Alcantara <palcantara@suse.de>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
Now signing is supported with RDMA transport.
Remove the code that disabled it.
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
|
|
The data buffer allocated on the stack can't be DMA'ed, ib_dma_map_page will
return an invalid DMA address for a buffer on stack. Even worse, this
incorrect address can't be detected by ib_dma_mapping_error. Sending data
from this address to hardware will not fail, but the remote peer will get
junk data.
Fix this by allocating the request on the heap in smb3_validate_negotiate.
Changes in v2:
Removed duplicated code on freeing buffers on function exit.
(Thanks to Parav Pandit <parav@mellanox.com>)
Fixed typo in the patch title.
Changes in v3:
Added "Fixes" to the patch.
Changed several sizeof() to use *pointer in place of struct.
Changes in v4:
Added detailed comments on the failure through RDMA.
Allocate request buffer using GPF_NOFS.
Fixed possible memory leak.
Changes in v5:
Removed variable ret for checking return value.
Changed to use pneg_inbuf->Dialects[0] to calculate unused space in pneg_inbuf.
Fixes: ff1c038addc4 ("Check SMB3 dialects against downgrade attacks")
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Tom Talpey <ttalpey@microsoft.com>
|
|
The NVIDIA Denver CPU also needs a PSCI call to harden the branch
predictor.
Signed-off-by: David Gilhooley <dgilhooley@nvidia.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This patch adds the MIDR encodings for NVIDIA as well as
the Denver and Carmel CPUs used in Tegra SoCs.
Signed-off-by: David Gilhooley <dgilhooley@nvidia.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Driver features data block has a boolean flag for PSR, use this to decide
whether PSR should be enabled on a platform. The module parameter can
still be used to override this.
Note: The feature currently remains disabled by default for all platforms
irrespective of what VBT says.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509003524.3199-1-dhinakaran.pandiyan@intel.com
|
|
The 0457:10fb touchscreen found on the Toshiba Click Mini L9W-B needs
to have a report-decriptors command send to it on resume in order for
the touchscreen to start generating events again on resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
USB controller ASM1042 stops working after commit de3ef1eb1cd0 (PM /
core: Drop run_wake flag from struct dev_pm_info).
The device in question is not power managed by platform firmware,
furthermore, it only supports PME# from D3cold:
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Before commit de3ef1eb1cd0, the device never gets runtime suspended.
After that commit, the device gets runtime suspended to D3hot, which can
not generate any PME#.
usb_hcd_pci_probe() unconditionally calls device_wakeup_enable(), hence
device_can_wakeup() in pci_dev_run_wake() always returns true.
So pci_dev_run_wake() needs to check PME wakeup capability as its first
condition.
In addition, change wakeup flag passed to pci_target_state() from false
to true, because we want to find the deepest state different from D3cold
that the device can still generate PME#. In this case, it's D0 for the
device in question.
Fixes: de3ef1eb1cd0 (PM / core: Drop run_wake flag from struct dev_pm_info)
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: 4.13+ <stable@vger.kernel.org> # 4.13+
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If the next_freq field of struct sugov_policy is set to UINT_MAX,
it shouldn't be used for updating the CPU frequency (this is a
special "invalid" value), but after commit b7eaf1aab9f8 (cpufreq:
schedutil: Avoid reducing frequency of busy CPUs prematurely) it
may be passed as the new frequency to sugov_update_commit() in
sugov_update_single().
Fix that by adding an extra check for the special UINT_MAX value
of next_freq to sugov_update_single().
Fixes: b7eaf1aab9f8 (cpufreq: schedutil: Avoid reducing frequency of busy CPUs prematurely)
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.12+ <stable@vger.kernel.org> # 4.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After commit 794a56ebd9a57 (sched/cpufreq: Change the worker kthread to
SCHED_DEADLINE) schedutil kthreads are "ignored" for a clock frequency
selection point of view, so the potential corner case for RT tasks is not
possible at all now.
Remove the stale comment mentioning it.
Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
P-state selection algorithm (powersave or performance) is selected by
echoing the desired choice to scaling_governor sysfs attribute and not
to scaling_cur_freq (as currently stated).
Fix it.
Signed-off-by: Juri Lelli <juri.lelli@redhat.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix a typo in admin-guide/pm/sleep-states.rst.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Prepare to allow the GuC submission to be run from underneath a
hardirq timer context (and not just the current softirq context) as is
required for fast preemption resets and context switches.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180508210318.10274-2-chris@chris-wilson.co.uk
|
|
Prepare to allow the execlists submission to be run from underneath a
hardirq timer context (and not just the current softirq context) as is
required for fast preemption resets and context switches.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180508210318.10274-1-chris@chris-wilson.co.uk
|
|
In igt_flush_test() we try to switch back to the kernel context, but we
are only able to do so when we are called with struct_mutex held.
More of my CI fallout from lockdep being temporarily suppressed :(
Fixes: 4cdf65ce8cc2 ("drm/i915/selftests: Return to kernel context after each test")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509065926.19207-1-chris@chris-wilson.co.uk
|
|
When using uni-planar formats (like RGB), the scaling parameters are
stored in plane 0, not plane 1.
Fixes: fc04023fafec ("drm/vc4: Add support for YUV planes.")
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180507121303.5610-1-boris.brezillon@bootlin.com
|
|
Calling mock_engine() calls i915_timeline_init() and that requires
struct_mutex to be held as it adds itself to the global list of
timelines. This error was introduced by commit a89d1f921c15 ("drm/i915:
Split i915_gem_timeline into individual timelines") but the issue was
masked in CI by the earlier lockdep spam.
Fixes: a89d1f921c15 ("drm/i915: Split i915_gem_timeline into individual timelines")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180508211056.17151-1-chris@chris-wilson.co.uk
|
|
Since commit a92a08499b1f "r8169: improve runtime pm in general and
suspend unused ports" interfaces w/o link are runtime-suspended after
10s. On systems where drivers take longer to load this can lead to the
situation that the interface is runtime-suspended already when it's
initially brought up.
This shouldn't be a problem because rtl_open() resumes MAC/PHY.
However with at least one chip version the interface doesn't properly
come up, as reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=199549
The vendor driver uses a delay to give certain chip versions some
time to resume before starting the PHY configuration. So let's do
the same. I don't know which chip versions may be affected,
therefore apply this delay always.
This patch was reported to fix the issue for RTL8168h.
I was able to reproduce the issue on an Asus H310I-Plus which also
uses a RTL8168h. Also in my case the patch fixed the issue.
Reported-by: Slava Kardakov <ojab@ojab.ru>
Tested-by: Slava Kardakov <ojab@ojab.ru>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch brings back possibility to use drivers depending on
DRM_EXYNOS, on Samsung S5PV210/S5PC110 series based systems.
Fixes: dbbc925bb83a ("drm/exynos: depend on ARCH_EXYNOS for DRM_EXYNOS")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch adds support for FIMD variant found on S5PV210 SoC.
Except CLKSEL bit availability, it is identical to Exynos4210.
Tested-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Use new return type vm_fault_t for fault handler
in struct vm_operations_struct.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into exynos-drm-next
Fixup pagefault issue of mixer driver
- it makes sure to check shadow register for interlace scan.
- it corrects chroma_addr[1], height and vertical position values.
And trivial cleanup
- it just removes duplicated drm_bridge_attach.
|
|
drm_bridge_attach takes care of these assignments, so there is no need
to open-code them a second time.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
CI noticed
<4>[ 23.430701] ============================================
<4>[ 23.430706] WARNING: possible recursive locking detected
<4>[ 23.430713] 4.17.0-rc4-CI-CI_DRM_4156+ #1 Not tainted
<4>[ 23.430720] --------------------------------------------
<4>[ 23.430725] systemd-udevd/169 is trying to acquire lock:
<4>[ 23.430732] (ptrval) (&(&timeline->lock)->rlock){....}, at: move_to_timeline+0x48/0x12c [i915]
<4>[ 23.430888]
but task is already holding lock:
<4>[ 23.430894] (ptrval) (&(&timeline->lock)->rlock){....}, at: i915_request_submit+0x1a/0x40 [i915]
<4>[ 23.430995]
other info that might help us debug this:
<4>[ 23.431002] Possible unsafe locking scenario:
<4>[ 23.431007] CPU0
<4>[ 23.431010] ----
<4>[ 23.431013] lock(&(&timeline->lock)->rlock);
<4>[ 23.431021] lock(&(&timeline->lock)->rlock);
<4>[ 23.431028]
*** DEADLOCK ***
<4>[ 23.431036] May be due to missing lock nesting notation
<4>[ 23.431044] 5 locks held by systemd-udevd/169:
<4>[ 23.431049] #0: (ptrval) (&dev->mutex){....}, at: __driver_attach+0x42/0xe0
<4>[ 23.431065] #1: (ptrval) (&dev->mutex){....}, at: __driver_attach+0x50/0xe0
<4>[ 23.431078] #2: (ptrval) (&dev->struct_mutex){+.+.}, at: i915_gem_init+0xca/0x630 [i915]
<4>[ 23.431174] #3: (ptrval) (rcu_read_lock){....}, at: submit_notify+0x35/0x124 [i915]
<4>[ 23.431271] #4: (ptrval) (&(&timeline->lock)->rlock){....}, at: i915_request_submit+0x1a/0x40 [i915]
<4>[ 23.431369]
stack backtrace:
<4>[ 23.431377] CPU: 0 PID: 169 Comm: systemd-udevd Not tainted 4.17.0-rc4-CI-CI_DRM_4156+ #1
<4>[ 23.431385] Hardware name: Dell Inc. OptiPlex GX280 /0G8310, BIOS A04 02/09/2005
<4>[ 23.431394] Call Trace:
<4>[ 23.431403] dump_stack+0x67/0x9b
<4>[ 23.431411] __lock_acquire+0xc67/0x1b50
<4>[ 23.431421] ? ring_buffer_lock_reserve+0x154/0x3f0
<4>[ 23.431429] ? lock_acquire+0xa6/0x210
<4>[ 23.431435] lock_acquire+0xa6/0x210
<4>[ 23.431530] ? move_to_timeline+0x48/0x12c [i915]
<4>[ 23.431540] _raw_spin_lock+0x2a/0x40
<4>[ 23.431634] ? move_to_timeline+0x48/0x12c [i915]
<4>[ 23.431730] move_to_timeline+0x48/0x12c [i915]
<4>[ 23.431826] __i915_request_submit+0xfa/0x280 [i915]
<4>[ 23.431923] i915_request_submit+0x25/0x40 [i915]
<4>[ 23.432024] i9xx_submit_request+0x11/0x140 [i915]
<4>[ 23.432120] submit_notify+0x8d/0x124 [i915]
<4>[ 23.432202] __i915_sw_fence_complete+0x81/0x250 [i915]
<4>[ 23.432300] __i915_request_add+0x31c/0x7c0 [i915]
<4>[ 23.432395] i915_gem_init+0x621/0x630 [i915]
<4>[ 23.432476] i915_driver_load+0xbee/0x10b0 [i915]
<4>[ 23.432485] ? trace_hardirqs_on_caller+0xe0/0x1b0
<4>[ 23.432566] i915_pci_probe+0x29/0x90 [i915]
<4>[ 23.432574] pci_device_probe+0xa1/0x130
<4>[ 23.432582] driver_probe_device+0x306/0x480
<4>[ 23.432589] __driver_attach+0xb7/0xe0
<4>[ 23.432596] ? driver_probe_device+0x480/0x480
<4>[ 23.432602] ? driver_probe_device+0x480/0x480
<4>[ 23.432609] bus_for_each_dev+0x74/0xc0
<4>[ 23.432616] bus_add_driver+0x15f/0x250
<4>[ 23.432623] ? 0xffffffffa02d7000
<4>[ 23.432629] driver_register+0x52/0xc0
<4>[ 23.432635] ? 0xffffffffa02d7000
<4>[ 23.432642] do_one_initcall+0x58/0x370
<4>[ 23.432653] ? do_init_module+0x1d/0x1ea
<4>[ 23.432660] ? rcu_read_lock_sched_held+0x6f/0x80
<4>[ 23.432667] ? kmem_cache_alloc_trace+0x282/0x2e0
<4>[ 23.432675] do_init_module+0x56/0x1ea
<4>[ 23.432682] load_module+0x2435/0x2b20
<4>[ 23.432694] ? __se_sys_finit_module+0xd3/0xf0
<4>[ 23.432701] __se_sys_finit_module+0xd3/0xf0
<4>[ 23.432710] do_syscall_64+0x55/0x190
<4>[ 23.432717] entry_SYSCALL_64_after_hwframe+0x49/0xbe
<4>[ 23.432724] RIP: 0033:0x7fa780782839
<4>[ 23.432729] RSP: 002b:00007ffcea73e668 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
<4>[ 23.432738] RAX: ffffffffffffffda RBX: 0000561a472a4b30 RCX: 00007fa780782839
<4>[ 23.432745] RDX: 0000000000000000 RSI: 00007fa7804610e5 RDI: 000000000000000e
<4>[ 23.432752] RBP: 00007fa7804610e5 R08: 0000000000000000 R09: 00007ffcea73e780
<4>[ 23.432758] R10: 000000000000000e R11: 0000000000000246 R12: 0000000000000000
<4>[ 23.432765] R13: 0000561a47296450 R14: 0000000000020000 R15: 0000561a472a4b30
but did not report it as an issue as it only occurred during the first
module on boot. This is due to the removal of the distinct global
timeline, and its separate lock class. So instead mark up the expected
nesting. An alternative would be to define a separate lock class for the
engine, but since we only expect to have a single point of nesting, we
can avoid having multiple lock classes for the struct.
Fixes: a89d1f921c15 ("drm/i915: Split i915_gem_timeline into individual timelines")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Tested-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180508153514.20251-1-chris@chris-wilson.co.uk
|
|
The i915_flip* tracepoints are no longer in use since the removal of CS
flip in commit 8b5d27b911d7 ("drm/i915: Remove intel_flip_work
infrastructure")
References: 8b5d27b911d7 ("drm/i915: Remove intel_flip_work infrastructure")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180508151552.31024-1-chris@chris-wilson.co.uk
|
|
DP_TRAINING_AUX_RD_INTERVAL with DP 1.3 spec changed bit scheeme from 8
bits to 7 in DPCD 0x000e. The 8th bit is used to identify extended
receiver capabilities. For panels that use this new feature wait interval
would be increased by 512 ms, when spec is max 16 ms. This behavior is
described in table 2-158 of DP 1.4 spec address 0000eh.
With the introduction of DP 1.4 spec main link clock recovery was
standardized to 100 us regardless of TRAINING_AUX_RD_INTERVAL value.
To avoid breaking panels that are not spec compiant we now warn on
invalid values.
V2: commit title/message, masking all 7 bits, warn on out of spec values.
V3: commit message, make link train clock recovery follow DP 1.4 spec.
V4: style changes
V5: typo
V6: print statement revisions, DP_REV to DPCD_REV, comment correction
V7: typo
V8: Style
V9: Strip out DPCD_REV_XX into seperate patch
v10: DPCD_REV_XX to DP_DPCD_REV_XX
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180504221800.17830-2-matthew.s.atwood@intel.com
|
