| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
ice: remaining TSPLL cleanups
These are the remaining patches from the "ice: Separate TSPLL from PTP
and cleanup" series [1] with control flow macros removed. What remains
are cleanups and some minor improvements.
[1] https://lore.kernel.org/netdev/20250618174231.3100231-1-anthony.l.nguyen@intel.com/
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: default to TIME_REF instead of TXCO on E825-C
ice: move TSPLL init calls to ice_ptp.c
ice: fall back to TCXO on TSPLL lock fail
ice: wait before enabling TSPLL
ice: add multiple TSPLL helpers
ice: use bitfields instead of unions for CGU regs
ice: read TSPLL registers again before reporting status
ice: clear time_sync_en field for E825-C during reprogramming
====================
Link: https://patch.msgid.link/20250626162921.1173068-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Rx rings are filled with Rx buffers. Which are supposed to fit
packet headers (or MTU if HW-GRO is disabled). The aggregation buffers
are filled with "device pages". Adjust the sizes of the page pool
recycling ring appropriately, based on ratio of the size of the
buffer on given ring vs system page size. Otherwise on a system
with 64kB pages we end up with >700MB of memory sitting in every
single page pool cache.
Correct the size calculation for the head_pool. Since the buffers
there are always small I'm pretty sure I meant to cap the size
at 1k, rather than make it the lowest possible size. With 64k pages
1k cache with a 1k ring is 64x larger than we need.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250626165441.4125047-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eric Dumazet says:
====================
tcp: fix DSACK bug with non contiguous ranges
This series combines a fix from xin.guo and a new packetdrill test.
====================
Link: https://patch.msgid.link/20250626123420.1933835-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Test DSACK behavior with non contiguous ranges.
Without prior fix (tcp: fix tcp_ofo_queue() to avoid including
too much DUP SACK range) this would fail with:
tcp_dsack_mult.pkt:37: error handling packet: bad value outbound TCP option 5
script packet: 0.100682 . 1:1(0) ack 6001 <nop,nop,sack 1001:3001 7001:8001>
actual packet: 0.100679 . 1:1(0) ack 6001 win 1097 <nop,nop,sack 1001:6001 7001:8001>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: xin.guo <guoxin0309@gmail.com>
Link: https://patch.msgid.link/20250626123420.1933835-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the new coming segment covers more than one skbs in the ofo queue,
and which seq is equal to rcv_nxt, then the sequence range
that is duplicated will be sent as DUP SACK, the detail as below,
in step6, the {501,2001} range is clearly including too much
DUP SACK range, in violation of RFC 2883 rules.
1. client > server: Flags [.], seq 501:1001, ack 1325288529, win 20000, length 500
2. server > client: Flags [.], ack 1, [nop,nop,sack 1 {501:1001}], length 0
3. client > server: Flags [.], seq 1501:2001, ack 1325288529, win 20000, length 500
4. server > client: Flags [.], ack 1, [nop,nop,sack 2 {1501:2001} {501:1001}], length 0
5. client > server: Flags [.], seq 1:2001, ack 1325288529, win 20000, length 2000
6. server > client: Flags [.], ack 2001, [nop,nop,sack 1 {501:2001}], length 0
After this fix, the final ACK is as below:
6. server > client: Flags [.], ack 2001, options [nop,nop,sack 1 {501:1001}], length 0
[edumazet] added a new packetdrill test in the following patch.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: xin.guo <guoxin0309@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250626123420.1933835-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eric Dumazet says:
====================
tcp: remove rtx_syn_ack and inet_rtx_syn_ack()
After DCCP removal, we can cleanup SYNACK retransmits a bit.
====================
Link: https://patch.msgid.link/20250626153017.2156274-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
inet_rtx_syn_ack() is a simple wrapper around tcp_rtx_synack(),
if we move req->num_retrans update.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250626153017.2156274-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now inet_rtx_syn_ack() is only used by TCP, it can directly
call tcp_rtx_synack() instead of using an indirect call
to req->rsk_ops->rtx_syn_ack().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250626153017.2156274-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To enable TLS ulp socket needs to be in established state.
This was added in commit d91c3e17f75f ("net/tls: Only attach
to sockets in ESTABLISHED state"), in 2018.
Signed-off-by: Ulrich Weber <ulrich.weber@gmail.com>
Link: https://patch.msgid.link/20250626145618.15464-1-ulrich.weber@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
"Co-posting selftests" belongs in the "netdev patch review" section,
same as "co-posting changes to user space components". It was
erroneously added as its own section.
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://patch.msgid.link/20250626182055.4161905-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Linus Walleij says:
====================
net: dsa: ks8995: Fix up bindings
After looking at the datasheets for KS8995 I realized this is
a DSA switch and need to have DT bindings as such and be implemented
as such.
This series just fixes up the bindings and the offending device tree.
The existing kernel driver which is in drivers/net/phy/spi_ks8995.c
does not implement DSA. It can be forgiven for this because it was
merged in 2011 and the DSA framework was not widely established
back then. It continues to probe fine but needs to be rewritten
to use the special DSA tag and moved to drivers/net/dsa as time
permits. (I hope I can do this.)
It's fine for the networking tree to merge both patches, I maintain
ixp4xx as well. But I can also carry the second patch through the
SoC tree if so desired.
v1: https://lore.kernel.org/20250624-ks8995-dsa-bindings-v1-0-71a8b4f63315@linaro.org
====================
Link: https://patch.msgid.link/20250625-ks8995-dsa-bindings-v2-0-ce71dce9be0b@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix up the KS8995 switch and PHYs the way that is most likely:
- Phy 1-4 is certainly the PHYs of the KS8995 (mask 0x1e in
the outoftree code masks PHYs 1,2,3,4).
- Phy 5 is the MII-P5 separate WAN phy of the KS8995 directly
connected to EthC.
- The EthB MII is probably connected as CPU interface to the
KS8995.
Properly integrate the KS8995 switch using the new bindings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250625-ks8995-dsa-bindings-v2-2-ce71dce9be0b@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After studying the datasheets for some of the KS8995 variants
it becomes pretty obvious that this is a straight-forward
and simple MII DSA switch with one port in (CPU) and four outgoing
ports, and it even supports custom tags by setting a bit in
a special register, and elaborate VLAN handling as all DSA
switches do.
What is a bit odd with KS8995 is that it uses an extra MII-P5
port to access one of the PHYs separately, on the side of the
switch fabric, such as when using a WAN port separately from
a LAN switch in a home router.
Rewrite the terse bindings to YAML, and move to the proper
subdirectory. Include a verbose example to make things clear.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250625-ks8995-dsa-bindings-v2-1-ce71dce9be0b@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Due to changes of my responsibilities within IBM i
can no longer act as maintainer for smc.
As a result of the co-operation with Alibaba over
the last years we decided to, once more, give them
more responsibility for smc by appointing
D. Wythe <alibuda@linux.alibaba.com> and
Dust Li <dust.li@linux.alibaba.com>
as maintainers as well.
Within IBM Sidraya Jayagond <sidraya@linux.ibm.com>
and Mahanta Jambigi <mjambigi@linux.ibm.com>
are going to take over the maintainership for smc.
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Link: https://patch.msgid.link/20250626051653.4259-1-jaka@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Allwinner A100/A133 has an Ethernet MAC (EMAC) controller that is
compatible with the A64 one. It features the same syscon registers for
control of the top-level integration of the unit.
Signed-off-by: Paul Kocialkowski <paulk@sys-base.io>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250626080923.632789-4-paulk@sys-base.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Paul Geurts says:
====================
NFC: trf7970a: Add option to reduce antenna gain
The TRF7970a device is sensitive to RF disturbances, which can make it
hard to pass some EMC immunity tests. By reducing the RX antenna gain,
the device becomes less sensitive to EMC disturbances, as a trade-off
against antenna performance.
====================
Link: https://patch.msgid.link/20250626141242.3749958-1-paul.geurts@prodrive-technologies.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The TRF7970a device is sensitive to RF disturbances, which can make it
hard to pass some EMC immunity tests. By reducing the RX antenna gain,
the device becomes less sensitive to EMC disturbances, as a trade-off
against antenna performance.
Add a device tree option to select RX gain reduction to improve EMC
performance.
Selecting a communication standard in the ISO control register resets
the RX antenna gain settings. Therefore set the RX gain reduction
everytime the ISO control register changes, when the option is used.
Signed-off-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250626141242.3749958-3-paul.geurts@prodrive-technologies.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add option to reduce the RX antenna gain to be able to reduce the
sensitivity.
Signed-off-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250626141242.3749958-2-paul.geurts@prodrive-technologies.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert lpc-eth.txt yaml format.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250624202028.2516257-1-Frank.Li@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
drm-misc-fixes for v6.16-rc4:
- Fix function signature of drm_writeback_connector_cleanup.
- Use correct HDMI audio bridge in drm_connector_hdmi_audio_init.
- Make HPD work on SN65DSI86.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://lore.kernel.org/r/3dd1d5e1-73b6-4b0c-a208-f7d6235cf530@linux.intel.com
|
|
Merge a fix from Jeff from a stable commit ID:
* ref_tracker: do xarray and workqueue job initializations earlier
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The kernel test robot reported an oops that occurred when attempting to
deregister a dentry from the xarray during subsys_initcall().
The ref_tracker xarrays and workqueue job are being initialized in
late_initcall() which is too late. Move those to postcore_initcall()
instead.
Fixes: 65b584f53611 ("ref_tracker: automatically register a file in debugfs for a ref_tracker_dir")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202506251406.c28f2adb-lkp@intel.com
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250626-reftrack-dbgfs-v1-1-812102e2a394@kernel.org
|
|
If the processing of the tr->events loop fails, the filter that has been
added to filter_head will be released twice in free_filter_list(&head->rcu)
and __free_filter(filter).
After adding the filter of tr->events, add the filter to the filter_head
process to avoid triggering uaf.
Link: https://lore.kernel.org/tencent_4EF87A626D702F816CD0951CE956EC32CD0A@qq.com
Fixes: a9d0aab5eb33 ("tracing: Fix regression of filter waiting a long time on RCU synchronization")
Reported-by: syzbot+daba72c4af9915e9c894@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=daba72c4af9915e9c894
Tested-by: syzbot+daba72c4af9915e9c894@syzkaller.appspotmail.com
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Revert a commit that attempted to fix a memory leak in an error code
path and introduced a different issue (Zhe Qiao)"
* tag 'acpi-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PCI/ACPI: Fix allocated memory release on error in pci_acpi_scan_root()"
|
|
Currently, for controllers with extended advertising, the advertising
data is set in the asynchronous response handler for extended
adverstising params. As most advertising settings are performed in a
synchronous context, the (asynchronous) setting of the advertising data
is done too late (after enabling the advertising).
Move setting of adverstising data from asynchronous response handler
into synchronous context to fix ordering of HCI commands.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: a0fb3726ba55 ("Bluetooth: Use Set ext adv/scan rsp data if controller supports")
Cc: stable@vger.kernel.org
v2: https://lore.kernel.org/linux-bluetooth/20250626115209.17839-1-ceggers@arri.de/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The unconditional call of hci_disable_advertising_sync() in
mesh_send_done_sync() also disables other LE advertisings (non mesh
related).
I am not sure whether this call is required at all, but checking the
adv_instances list (like done at other places) seems to solve the
problem.
Fixes: b338d91703fa ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
According to the message of commit b338d91703fa ("Bluetooth: Implement
support for Mesh"), MGMT_OP_SET_MESH_RECEIVER should set the passive scan
parameters. Currently the scan interval and window parameters are
silently ignored, although user space (bluetooth-meshd) expects that
they can be used [1]
[1] https://git.kernel.org/pub/scm/bluetooth/bluez.git/tree/mesh/mesh-io-mgmt.c#n344
Fixes: b338d91703fa ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This reverts minor parts of the changes made in commit b338d91703fa
("Bluetooth: Implement support for Mesh"). It looks like these changes
were only made for development purposes but shouldn't have been part of
the commit.
Fixes: b338d91703fa ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When PA Create Sync is enabled, advertising resumes unexpectedly.
Therefore, it's necessary to check whether advertising is currently
active before attempting to pause it.
< HCI Command: LE Add Device To... (0x08|0x0011) plen 7 #1345 [hci0] 48.306205
Address type: Random (0x01)
Address: 4F:84:84:5F:88:17 (Resolvable)
Identity type: Random (0x01)
Identity: FC:5B:8C:F7:5D:FB (Static)
< HCI Command: LE Set Address Re.. (0x08|0x002d) plen 1 #1347 [hci0] 48.308023
Address resolution: Enabled (0x01)
...
< HCI Command: LE Set Extended A.. (0x08|0x0039) plen 6 #1349 [hci0] 48.309650
Extended advertising: Enabled (0x01)
Number of sets: 1 (0x01)
Entry 0
Handle: 0x01
Duration: 0 ms (0x00)
Max ext adv events: 0
...
< HCI Command: LE Periodic Adve.. (0x08|0x0044) plen 14 #1355 [hci0] 48.314575
Options: 0x0000
Use advertising SID, Advertiser Address Type and address
Reporting initially enabled
SID: 0x02
Adv address type: Random (0x01)
Adv address: 4F:84:84:5F:88:17 (Resolvable)
Identity type: Random (0x01)
Identity: FC:5B:8C:F7:5D:FB (Static)
Skip: 0x0000
Sync timeout: 20000 msec (0x07d0)
Sync CTE type: 0x0000
Fixes: ad383c2c65a5 ("Bluetooth: hci_sync: Enable advertising when LL privacy is enabled")
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Pull block fixes from Jens Axboe:
- Fixes for ublk:
- fix C++ narrowing warnings in the uapi header
- update/improve UBLK_F_SUPPORT_ZERO_COPY comment in uapi header
- fix for the ublk ->queue_rqs() implementation, limiting a batch
to just the specific task AND ring
- ublk_get_data() error handling fix
- sanity check more arguments in ublk_ctrl_add_dev()
- selftest addition
- NVMe pull request via Christoph:
- reset delayed remove_work after reconnect
- fix atomic write size validation
- Fix for a warning introduced in bdev_count_inflight_rw() in this
merge window
* tag 'block-6.16-20250626' of git://git.kernel.dk/linux:
block: fix false warning in bdev_count_inflight_rw()
ublk: sanity check add_dev input for underflow
nvme: fix atomic write size validation
nvme: refactor the atomic write unit detection
nvme: reset delayed remove_work after reconnect
ublk: setup ublk_io correctly in case of ublk_get_data() failure
ublk: update UBLK_F_SUPPORT_ZERO_COPY comment in UAPI header
ublk: fix narrowing warnings in UAPI header
selftests: ublk: don't take same backing file for more than one ublk devices
ublk: build batch from IOs in same io_ring_ctx and io task
|
|
Pull io_uring fixes from Jens Axboe:
- Two tweaks for a recent fix: fixing a memory leak if multiple iovecs
were initially mapped but only the first was used and hence turned
into a UBUF rathan than an IOVEC iterator, and catching a case where
a retry would be done even if the previous segment wasn't full
- Small series fixing an issue making the vm unhappy if debugging is
turned on, hitting a VM_BUG_ON_PAGE()
- Fix a resource leak in io_import_dmabuf() in the error handling case,
which is a regression in this merge window
- Mark fallocate as needing to be write serialized, as is already done
for truncate and buffered writes
* tag 'io_uring-6.16-20250626' of git://git.kernel.dk/linux:
io_uring/kbuf: flag partial buffer mappings
io_uring/net: mark iov as dynamically allocated even for single segments
io_uring: fix resource leak in io_import_dmabuf()
io_uring: don't assume uaddr alignment in io_vec_fill_bvec
io_uring/rsrc: don't rely on user vaddr alignment
io_uring/rsrc: fix folio unpinning
io_uring: make fallocate be hashed work
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata fix from Niklas Cassel:
- Use the correct DMI identifier for ASUSPRO-D840SA LPM quirk such that
the quirk actually gets applied (me)
* tag 'ata-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: ahci: Use correct DMI identifier for ASUSPRO-D840SA LPM quirk
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Alexander Gordeev:
- Fix incorrectly dropped dereferencing of the stack nth entry
introduced with a previous KASAN false positive fix
- Use a proper memdup_array_user() helper to prevent overflow in a
protected key size calculation
* tag 's390-6.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ptrace: Fix pointer dereferencing in regs_get_kernel_stack_nth()
s390/pkey: Prevent overflow in size calculation for memdup_user()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes again:
- A regression fix for hibernation bug in ASoC SoundWire
- Fixes for the new Qualcomm USB offload stuff
- A potential OOB access fix in USB-audio
- A potential memleadk fix in ASoC Intel
- Quirks for HD-audio and ASoC AMD ACP"
* tag 'sound-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Fix built-in mic on ASUS VivoBook X507UAR
ALSA: usb: qcom: fix NULL pointer dereference in qmi_stop_session
ASoC: SOF: Intel: hda: Use devm_kstrdup() to avoid memleak.
ASoC: rt721-sdca: fix boost gain calculation error
ALSA: qc_audio_offload: Fix missing error code in prepare_qmi_response()
ALSA: hda/realtek: Add mic-mute LED setup for ASUS UM5606
ALSA: usb-audio: Fix out-of-bounds read in snd_usb_get_audioformat_uac3()
ALSA: hda/realtek: fix mute/micmute LEDs for HP EliteBook 6 G1a
ASoC: amd: ps: fix for soundwire failures during hibernation exit sequence
ASoC: amd: yc: Add DMI quirk for Lenovo IdeaPad Slim 5 15
ASoC: amd: yc: add quirk for Acer Nitro ANV15-41 internal mic
ASoC: qcom: sm8250: Fix possibly undefined reference
ALSA: hda/realtek - Enable mute LED on HP Pavilion Laptop 15-eg100
ALSA: hda/realtek: Add quirks for some Clevo laptops
|
|
Unmount of a shutdown filesystem can hang with stale inode cluster
buffers in the AIL like so:
[95964.140623] Call Trace:
[95964.144641] __schedule+0x699/0xb70
[95964.154003] schedule+0x64/0xd0
[95964.156851] xfs_ail_push_all_sync+0x9b/0xf0
[95964.164816] xfs_unmount_flush_inodes+0x41/0x70
[95964.168698] xfs_unmountfs+0x7f/0x170
[95964.171846] xfs_fs_put_super+0x3b/0x90
[95964.175216] generic_shutdown_super+0x77/0x160
[95964.178060] kill_block_super+0x1b/0x40
[95964.180553] xfs_kill_sb+0x12/0x30
[95964.182796] deactivate_locked_super+0x38/0x100
[95964.185735] deactivate_super+0x41/0x50
[95964.188245] cleanup_mnt+0x9f/0x160
[95964.190519] __cleanup_mnt+0x12/0x20
[95964.192899] task_work_run+0x89/0xb0
[95964.195221] resume_user_mode_work+0x4f/0x60
[95964.197931] syscall_exit_to_user_mode+0x76/0xb0
[95964.201003] do_syscall_64+0x74/0x130
$ pstree -N mnt |grep umount
|-check-parallel---nsexec---run_test.sh---753---umount
It always seems to be generic/753 that triggers this, and repeating
a quick group test run triggers it every 10-15 iterations. Hence it
generally triggers once up every 30-40 minutes of test time. just
running generic/753 by itself or concurrently with a limited group
of tests doesn't reproduce this issue at all.
Tracing on a hung system shows the AIL repeating every 50ms a log
force followed by an attempt to push pinned, aborted inodes from the
AIL (trimmed for brevity):
xfs_log_force: lsn 0x1c caller xfsaild+0x18e
xfs_log_force: lsn 0x0 caller xlog_cil_flush+0xbd
xfs_log_force: lsn 0x1c caller xfs_log_force+0x77
xfs_ail_pinned: lip 0xffff88826014afa0 lsn 1/37472 type XFS_LI_INODE flags IN_AIL|ABORTED
xfs_ail_pinned: lip 0xffff88814000a708 lsn 1/37472 type XFS_LI_INODE flags IN_AIL|ABORTED
xfs_ail_pinned: lip 0xffff88810b850c80 lsn 1/37472 type XFS_LI_INODE flags IN_AIL|ABORTED
xfs_ail_pinned: lip 0xffff88810b850af0 lsn 1/37472 type XFS_LI_INODE flags IN_AIL|ABORTED
xfs_ail_pinned: lip 0xffff888165cf0a28 lsn 1/37472 type XFS_LI_INODE flags IN_AIL|ABORTED
xfs_ail_pinned: lip 0xffff88810b850bb8 lsn 1/37472 type XFS_LI_INODE flags IN_AIL|ABORTED
....
The inode log items are marked as aborted, which means that either:
a) a transaction commit has occurred, seen an error or shutdown, and
called xfs_trans_free_items() to abort the items. This should happen
before any pinning of log items occurs.
or
b) a dirty transaction has been cancelled. This should also happen
before any pinning of log items occurs.
or
c) AIL insertion at journal IO completion is marked as aborted. In
this case, the log item is pinned by the CIL until journal IO
completes and hence needs to be unpinned. This is then done after
the ->iop_committed() callback is run, so the pin count should be
balanced correctly.
Yet none of these seemed to be occurring. Further tracing indicated
this:
d) Shutdown during CIL pushing resulting in log item completion
being called from checkpoint abort processing. Items are unpinned
and released without serialisation against each other, journal IO
completion or transaction commit completion.
In this case, we may still have a transaction commit in flight that
holds a reference to a xfs_buf_log_item (BLI) after CIL insertion.
e.g. a synchronous transaction will flush the CIL before the
transaction is torn down. The concurrent CIL push then aborts
insertion it and drops the commit/AIL reference to the BLI. This can
leave the transaction commit context with the last reference to the
BLI which is dropped here:
xfs_trans_free_items()
->iop_release
xfs_buf_item_release
xfs_buf_item_put
if (XFS_LI_ABORTED)
xfs_trans_ail_delete
xfs_buf_item_relse()
Unlike the journal completion ->iop_unpin path, this path does not
run stale buffer completion process when it drops the last
reference, hence leaving the stale inodes attached to the buffer
sitting the AIL. There are no other references to those inodes, so
there is no other mechanism to remove them from the AIL. Hence
unmount hangs.
The buffer lock context for stale buffers is passed to the last BLI
reference. This is normally the last BLI unpin on journal IO
completion. The unpin then processes the stale buffer completion and
releases the buffer lock. However, if the final unpin from journal
IO completion (or CIL push abort) does not hold the last reference
to the BLI, there -must- still be a transaction context that
references the BLI, and so that context must perform the stale
buffer completion processing before the buffer is unlocked and the
BLI torn down.
The fix for this is to rework the xfs_buf_item_relse() path to run
stale buffer completion processing if it drops the last reference to
the BLI. We still hold the buffer locked, so the buffer owner and
lock context is the same as if we passed the BLI and buffer to the
->iop_unpin() context to finish stale process on journal commit.
However, we have to be careful here. In a shutdown state, we can be
freeing dirty BLIs from xfs_buf_item_put() via xfs_trans_brelse()
and xfs_trans_bdetach(). The existing code handles this case by
considering shutdown state as "aborted", but in doing so
largely masks the failure to clean up stale BLI state from the
xfs_buf_item_relse() path. i.e regardless of the shutdown state and
whether the item is in the AIL, we must finish the stale buffer
cleanup if we are are dropping the last BLI reference from the
->iop_relse path in transaction commit context.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
The stale buffer item completion handling is currently only done
from BLI unpinning. We need to perform this function from where-ever
the last reference to the BLI is dropped, so first we need to
factor this code out into a helper.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
The code to initialise, release and free items is all the way down
the bottom of the file. Upcoming fixes need to these functions
earlier in the file, so move them to the top.
There is one code change in this move - the parameter to
xfs_buf_item_relse() is changed from the xfs_buf to the
xfs_buf_log_item - the thing that the function is releasing.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
I needed more insight into how stale inodes were getting stuck on
the AIL after a forced shutdown when running fsstress. These are the
tracepoints I added for that purpose.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
On shutdown when quotas are enabled, the shutdown can deadlock
trying to unpin the dquot buffer buf_log_item like so:
[ 3319.483590] task:kworker/20:0H state:D stack:14360 pid:1962230 tgid:1962230 ppid:2 task_flags:0x4208060 flags:0x00004000
[ 3319.493966] Workqueue: xfs-log/dm-6 xlog_ioend_work
[ 3319.498458] Call Trace:
[ 3319.500800] <TASK>
[ 3319.502809] __schedule+0x699/0xb70
[ 3319.512672] schedule+0x64/0xd0
[ 3319.515573] schedule_timeout+0x30/0xf0
[ 3319.528125] __down_common+0xc3/0x200
[ 3319.531488] __down+0x1d/0x30
[ 3319.534186] down+0x48/0x50
[ 3319.540501] xfs_buf_lock+0x3d/0xe0
[ 3319.543609] xfs_buf_item_unpin+0x85/0x1b0
[ 3319.547248] xlog_cil_committed+0x289/0x570
[ 3319.571411] xlog_cil_process_committed+0x6d/0x90
[ 3319.575590] xlog_state_shutdown_callbacks+0x52/0x110
[ 3319.580017] xlog_force_shutdown+0x169/0x1a0
[ 3319.583780] xlog_ioend_work+0x7c/0xb0
[ 3319.587049] process_scheduled_works+0x1d6/0x400
[ 3319.591127] worker_thread+0x202/0x2e0
[ 3319.594452] kthread+0x20c/0x240
The CIL push has seen the deadlock, so it has aborted the push and
is running CIL checkpoint completion to abort all the items in the
checkpoint. This calls ->iop_unpin(remove = true) to clean up the
log items in the checkpoint.
When a buffer log item is unpined like this, it needs to lock the
buffer to run io completion to correctly fail the buffer and run all
the required completions to fail attached log items as well. In this
case, the attempt to lock the buffer on unpin is hanging because the
buffer is already locked.
I suspected a leaked XFS_BLI_HOLD state because of XFS_BLI_STALE
handling changes I was testing, so I went looking for
pin events on HOLD buffers and unpin events on locked buffer. That
isolated this one buffer with these two events:
xfs_buf_item_pin: dev 251:6 daddr 0xa910 bbcount 0x2 hold 2 pincount 0 lock 0 flags DONE|KMEM recur 0 refcount 1 bliflags HOLD|DIRTY|LOGGED liflags DIRTY
....
xfs_buf_item_unpin: dev 251:6 daddr 0xa910 bbcount 0x2 hold 4 pincount 1 lock 0 flags DONE|KMEM recur 0 refcount 1 bliflags DIRTY liflags ABORTED
Firstly, bbcount = 0x2, which means it is not a single sector
structure. That rules out every xfs_trans_bhold() case except one:
dquot buffers.
Then hung task dumping gave this trace:
[ 3197.312078] task:fsync-tester state:D stack:12080 pid:2051125 tgid:2051125 ppid:1643233 task_flags:0x400000 flags:0x00004002
[ 3197.323007] Call Trace:
[ 3197.325581] <TASK>
[ 3197.327727] __schedule+0x699/0xb70
[ 3197.334582] schedule+0x64/0xd0
[ 3197.337672] schedule_timeout+0x30/0xf0
[ 3197.350139] wait_for_completion+0xbd/0x180
[ 3197.354235] __flush_workqueue+0xef/0x4e0
[ 3197.362229] xlog_cil_force_seq+0xa0/0x300
[ 3197.374447] xfs_log_force+0x77/0x230
[ 3197.378015] xfs_qm_dqunpin_wait+0x49/0xf0
[ 3197.382010] xfs_qm_dqflush+0x55/0x460
[ 3197.385663] xfs_qm_dquot_isolate+0x29e/0x4d0
[ 3197.389977] __list_lru_walk_one+0x141/0x220
[ 3197.398867] list_lru_walk_one+0x10/0x20
[ 3197.402713] xfs_qm_shrink_scan+0x6a/0x100
[ 3197.406699] do_shrink_slab+0x18a/0x350
[ 3197.410512] shrink_slab+0xf7/0x430
[ 3197.413967] drop_slab+0x97/0xf0
[ 3197.417121] drop_caches_sysctl_handler+0x59/0xc0
[ 3197.421654] proc_sys_call_handler+0x18b/0x280
[ 3197.426050] proc_sys_write+0x13/0x20
[ 3197.429750] vfs_write+0x2b8/0x3e0
[ 3197.438532] ksys_write+0x7e/0xf0
[ 3197.441742] __x64_sys_write+0x1b/0x30
[ 3197.445363] x64_sys_call+0x2c72/0x2f60
[ 3197.449044] do_syscall_64+0x6c/0x140
[ 3197.456341] entry_SYSCALL_64_after_hwframe+0x76/0x7e
Yup, another test run by check-parallel is running drop_caches
concurrently and the dquot shrinker for the hung filesystem is
running. That's trying to flush a dirty dquot from reclaim context,
and it waiting on a log force to complete. xfs_qm_dqflush is called
with the dquot buffer held locked, and so we've called
xfs_log_force() with that buffer locked.
Now the log force is waiting for a workqueue flush to complete, and
that workqueue flush is waiting of CIL checkpoint processing to
finish.
The CIL checkpoint processing is aborting all the log items it has,
and that requires locking aborted buffers to cancel them.
Now, normally this isn't a problem if we are issuing a log force
to unpin an object, because the ->iop_unpin() method wakes pin
waiters first. That results in the pin waiter finishing off whatever
it was doing, dropping the lock and then xfs_buf_item_unpin() can
lock the buffer and fail it.
However, xfs_qm_dqflush() is waiting on the -dquot- unpin event, not
the dquot buffer unpin event, and so it never gets woken and so does
not drop the buffer lock.
Inodes do not have this problem, as they can only be written from
one spot (->iop_push) whilst dquots can be written from multiple
places (memory reclaim, ->iop_push, xfs_dq_dqpurge, and quotacheck).
The reason that the dquot buffer has an attached buffer log item is
that it has been recently allocated. Initialisation of the dquot
buffer logs the buffer directly, thereby pinning it in memory. We
then modify the dquot in a separate operation, and have memory
reclaim racing with a shutdown and we trigger this deadlock.
check-parallel reproduces this reliably on 1kB FSB filesystems with
quota enabled because it does all of these things concurrently
without having to explicitly write tests to exercise these corner
case conditions.
xfs_qm_dquot_logitem_push() doesn't have this deadlock because it
checks if the dquot is pinned before locking the dquot buffer and
skipping it if it is pinned. This means the xfs_qm_dqunpin_wait()
log force in xfs_qm_dqflush() never triggers and we unlock the
buffer safely allowing a concurrent shutdown to fail the buffer
appropriately.
xfs_qm_dqpurge() could have this problem as it is called from
quotacheck and we might have allocated dquot buffers when recording
the quota updates. This can be fixed by calling
xfs_qm_dqunpin_wait() before we lock the dquot buffer. Because we
hold the dquot locked, nothing will be able to add to the pin count
between the unpin_wait and the dqflush callout, so this now makes
xfs_qm_dqpurge() safe against this race.
xfs_qm_dquot_isolate() can also be fixed this same way but, quite
frankly, we shouldn't be doing IO in memory reclaim context. If the
dquot is pinned or dirty, simply rotate it and let memory reclaim
come back to it later, same as we do for inodes.
This then gets rid of the nasty issue in xfs_qm_flush_one() where
quotacheck writeback races with memory reclaim flushing the dquots.
We can lift xfs_qm_dqunpin_wait() up into this code, then get rid of
the "can't get the dqflush lock" buffer write to cycle the dqlfush
lock and enable it to be flushed again. checking if the dquot is
pinned and returning -EAGAIN so that the dquot walk will revisit the
dquot again later.
Finally, with xfs_qm_dqunpin_wait() lifted into all the callers,
we can remove it from the xfs_qm_dqflush() code.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
There is a race condition that can trigger in dmflakey fstests that
can result in asserts in xfs_ialloc_read_agi() and
xfs_alloc_read_agf() firing. The asserts look like this:
XFS: Assertion failed: pag->pagf_freeblks == be32_to_cpu(agf->agf_freeblks), file: fs/xfs/libxfs/xfs_alloc.c, line: 3440
.....
Call Trace:
<TASK>
xfs_alloc_read_agf+0x2ad/0x3a0
xfs_alloc_fix_freelist+0x280/0x720
xfs_alloc_vextent_prepare_ag+0x42/0x120
xfs_alloc_vextent_iterate_ags+0x67/0x260
xfs_alloc_vextent_start_ag+0xe4/0x1c0
xfs_bmapi_allocate+0x6fe/0xc90
xfs_bmapi_convert_delalloc+0x338/0x560
xfs_map_blocks+0x354/0x580
iomap_writepages+0x52b/0xa70
xfs_vm_writepages+0xd7/0x100
do_writepages+0xe1/0x2c0
__writeback_single_inode+0x44/0x340
writeback_sb_inodes+0x2d0/0x570
__writeback_inodes_wb+0x9c/0xf0
wb_writeback+0x139/0x2d0
wb_workfn+0x23e/0x4c0
process_scheduled_works+0x1d4/0x400
worker_thread+0x234/0x2e0
kthread+0x147/0x170
ret_from_fork+0x3e/0x50
ret_from_fork_asm+0x1a/0x30
I've seen the AGI variant from scrub running on the filesysetm
after unmount failed due to systemd interference:
XFS: Assertion failed: pag->pagi_freecount == be32_to_cpu(agi->agi_freecount) || xfs_is_shutdown(pag->pag_mount), file: fs/xfs/libxfs/xfs_ialloc.c, line: 2804
.....
Call Trace:
<TASK>
xfs_ialloc_read_agi+0xee/0x150
xchk_perag_drain_and_lock+0x7d/0x240
xchk_ag_init+0x34/0x90
xchk_inode_xref+0x7b/0x220
xchk_inode+0x14d/0x180
xfs_scrub_metadata+0x2e2/0x510
xfs_ioc_scrub_metadata+0x62/0xb0
xfs_file_ioctl+0x446/0xbf0
__se_sys_ioctl+0x6f/0xc0
__x64_sys_ioctl+0x1d/0x30
x64_sys_call+0x1879/0x2ee0
do_syscall_64+0x68/0x130
? exc_page_fault+0x62/0xc0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Essentially, it is the same problem. When _flakey_drop_and_remount()
loads the drop-writes table, it makes all writes silently fail. Writes
are reported to the fs as completed successfully, but they are not
issued to the backing store. The filesystem sees the successful
write completion and marks the metadata buffer clean and removes it
from the AIL.
If this happens at the same time as memory pressure is occuring,
the now-clean AGF and/or AGI buffers can be reclaimed from memory.
Shortly afterwards, but before _flakey_drop_and_remount() runs
unmount, background writeback is kicked and it tries to allocate
blocks for the dirty pages in memory. This then tries to access the
AGF buffer we just turfed out of memory. It's not found, so it gets
read in from disk.
This is all fine, except for the fact that the last writeback of the
AGF did not actually reach disk. The AGF on disk is stale compared
to the in-memory state held by the perag, and so they don't match
and the assert fires.
Then other operations on that inode hang because the task was killed
whilst holding inode locks. e.g:
Workqueue: xfs-conv/dm-12 xfs_end_io
Call Trace:
<TASK>
__schedule+0x650/0xb10
schedule+0x6d/0xf0
schedule_preempt_disabled+0x15/0x30
rwsem_down_write_slowpath+0x31a/0x5f0
down_write+0x43/0x60
xfs_ilock+0x1a8/0x210
xfs_trans_alloc_inode+0x9c/0x240
xfs_iomap_write_unwritten+0xe3/0x300
xfs_end_ioend+0x90/0x130
xfs_end_io+0xce/0x100
process_scheduled_works+0x1d4/0x400
worker_thread+0x234/0x2e0
kthread+0x147/0x170
ret_from_fork+0x3e/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
and it's all down hill from there.
Memory pressure is one way to trigger this, another is to run "echo
3 > /proc/sys/vm/drop_caches" randomly while tests are running.
Regardless of how it is triggered, this effectively takes down the
system once umount hangs because it's holding a sb->s_umount lock
exclusive and now every sync(1) call gets stuck on it.
Fix this by replacing the asserts with a corruption detection check
and a shutdown.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
Lock order of xfs_ifree_cluster() is cluster buffer -> try ILOCK
-> IFLUSHING, except for the last inode in the cluster that is
triggering the free. In that case, the lock order is ILOCK ->
cluster buffer -> IFLUSHING.
xfs_iflush_cluster() uses cluster buffer -> try ILOCK -> IFLUSHING,
so this can safely run concurrently with xfs_ifree_cluster().
xfs_inode_item_precommit() uses ILOCK -> cluster buffer, but this
cannot race with xfs_ifree_cluster() so being in a different order
will not trigger a deadlock.
xfs_reclaim_inode() during a filesystem shutdown uses ILOCK ->
IFLUSHING -> cluster buffer via xfs_iflush_shutdown_abort(), and
this deadlocks against xfs_ifree_cluster() like so:
sysrq: Show Blocked State
task:kworker/10:37 state:D stack:12560 pid:276182 tgid:276182 ppid:2 flags:0x00004000
Workqueue: xfs-inodegc/dm-3 xfs_inodegc_worker
Call Trace:
<TASK>
__schedule+0x650/0xb10
schedule+0x6d/0xf0
schedule_timeout+0x8b/0x180
schedule_timeout_uninterruptible+0x1e/0x30
xfs_ifree+0x326/0x730
xfs_inactive_ifree+0xcb/0x230
xfs_inactive+0x2c8/0x380
xfs_inodegc_worker+0xaa/0x180
process_scheduled_works+0x1d4/0x400
worker_thread+0x234/0x2e0
kthread+0x147/0x170
ret_from_fork+0x3e/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
task:fsync-tester state:D stack:12160 pid:2255943 tgid:2255943 ppid:3988702 flags:0x00004006
Call Trace:
<TASK>
__schedule+0x650/0xb10
schedule+0x6d/0xf0
schedule_timeout+0x31/0x180
__down_common+0xbe/0x1f0
__down+0x1d/0x30
down+0x48/0x50
xfs_buf_lock+0x3d/0xe0
xfs_iflush_shutdown_abort+0x51/0x1e0
xfs_icwalk_ag+0x386/0x690
xfs_reclaim_inodes_nr+0x114/0x160
xfs_fs_free_cached_objects+0x19/0x20
super_cache_scan+0x17b/0x1a0
do_shrink_slab+0x180/0x350
shrink_slab+0xf8/0x430
drop_slab+0x97/0xf0
drop_caches_sysctl_handler+0x59/0xc0
proc_sys_call_handler+0x189/0x280
proc_sys_write+0x13/0x20
vfs_write+0x33d/0x3f0
ksys_write+0x7c/0xf0
__x64_sys_write+0x1b/0x30
x64_sys_call+0x271d/0x2ee0
do_syscall_64+0x68/0x130
entry_SYSCALL_64_after_hwframe+0x76/0x7e
We can't change the lock order of xfs_ifree_cluster() - XFS_ISTALE
and XFS_IFLUSHING are serialised through to journal IO completion
by the cluster buffer lock being held.
There's quite a few asserts in the code that check that XFS_ISTALE
does not occur out of sync with buffer locking (e.g. in
xfs_iflush_cluster). There's also a dependency on the inode log item
being removed from the buffer before XFS_IFLUSHING is cleared, also
with asserts that trigger on this.
Further, we don't have a requirement for the inode to be locked when
completing or aborting inode flushing because all the inode state
updates are serialised by holding the cluster buffer lock across the
IO to completion.
We can't check for XFS_IRECLAIM in xfs_ifree_mark_inode_stale() and
skip the inode, because there is no guarantee that the inode will be
reclaimed. Hence it *must* be marked XFS_ISTALE regardless of
whether reclaim is preparing to free that inode. Similarly, we can't
check for IFLUSHING before locking the inode because that would
result in dirty inodes not being marked with ISTALE in the event of
racing with XFS_IRECLAIM.
Hence we have to address this issue from the xfs_reclaim_inode()
side. It is clear that we cannot hold the inode locked here when
calling xfs_iflush_shutdown_abort() because it is the inode->buffer
lock order that causes the deadlock against xfs_ifree_cluster().
Hence we need to drop the ILOCK before aborting the inode in the
shutdown case. Once we've aborted the inode, we can grab the ILOCK
again and then immediately reclaim it as it is now guaranteed to be
clean.
Note that dropping the ILOCK in xfs_reclaim_inode() means that it
can now be locked by xfs_ifree_mark_inode_stale() and seen whilst in
this state. This is safe because we have left the XFS_IFLUSHING flag
on the inode and so xfs_ifree_mark_inode_stale() will simply set
XFS_ISTALE and move to the next inode. An ASSERT check in this path
needs to be tweaked to take into account this new shutdown
interaction.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
It already depends on X86_32, but that's also set for ARCH=um.
Recent changes made UML no longer have IO port access since
it's not needed, but this driver uses it. Build it only for
HAS_IOPORT. This is pretty much the same as depending on X86,
but on the off-chance that HAS_IOPORT will ever be optional
on x86 HAS_IOPORT is the real prerequisite.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Property "num_cpu" and "feature" are read-only once eiointc is created,
which are set with KVM_DEV_LOONGARCH_EXTIOI_GRP_CTRL attr group before
device creation.
Attr group KVM_DEV_LOONGARCH_EXTIOI_GRP_SW_STATUS is to update register
and software state for migration and reset usage, property "num_cpu" and
"feature" can not be update again if it is created already.
Here discard write operation with property "num_cpu" and "feature" in
attr group KVM_DEV_LOONGARCH_EXTIOI_GRP_CTRL.
Cc: stable@vger.kernel.org
Fixes: 1ad7efa552fd ("LoongArch: KVM: Add EIOINTC user mode read and write functions")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The maximum supported cpu number is EIOINTC_ROUTE_MAX_VCPUS about
irqchip EIOINTC, here add validation about cpu number to avoid array
pointer overflow.
Cc: stable@vger.kernel.org
Fixes: 1ad7efa552fd ("LoongArch: KVM: Add EIOINTC user mode read and write functions")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
With EIOINTC interrupt controller, physical CPU ID is set for irq route.
However the function kvm_get_vcpu() is used to get destination vCPU when
delivering irq. With API kvm_get_vcpu(), the logical CPU ID is used.
With API kvm_get_vcpu_by_cpuid(), vCPU ID can be searched from physical
CPU ID.
Cc: stable@vger.kernel.org
Fixes: 3956a52bc05b ("LoongArch: KVM: Add EIOINTC read and write functions")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
With function eiointc_update_sw_coremap(), there is forced assignment
like val = *(u64 *)pvalue. Parameter pvalue may be pointer to char type
or others, there is problem with forced assignment with u64 type.
Here the detailed value is passed rather address pointer.
Cc: stable@vger.kernel.org
Fixes: 3956a52bc05b ("LoongArch: KVM: Add EIOINTC read and write functions")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
IOCSR instruction supports 1/2/4/8 bytes access, the address should be
naturally aligned with its access size. Here address alignment check is
added in the EIOINTC kernel emulation.
Cc: stable@vger.kernel.org
Fixes: 3956a52bc05b ("LoongArch: KVM: Add EIOINTC read and write functions")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
i2c-host fixes for v6.16-rc4
- imx: fix SMBus protocol compliance during block read
- omap: fix error handling path in probe
- robotfuzz, tiny-usb: prevent zero-length reads
- x86, designware, amdisp: fix build error when modules are
disabled
|
|
Correct spelling as flagged by codespell.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Airoha AN7583 SoC have 2 dedicated MDIO bus controller in the SCU
register map. To driver register an MDIO controller based on the DT
reg property and access the register by accessing the parent syscon.
The MDIO bus logic is similar to the MT7530 internal MDIO bus but
deviates of some setting and some HW bug.
On Airoha AN7583 the MDIO clock is set to 25MHz by default and needs to
be correctly setup to 2.5MHz to correctly work (by setting the divisor
to 10x).
There seems to be Hardware bug where AN7583_MII_RWDATA
is not wiped in the context of unconnected PHY and the
previous read value is returned.
Example: (only one PHY on the BUS at 0x1f)
- read at 0x1f report at 0x2 0x7500
- read at 0x0 report 0x7500 on every address
To workaround this, we reset the Mdio BUS at every read
to have consistent values on read operation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
