summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-01-01bnx2x: Fix incorrect link-up reportYaniv Rosner
Fix a problem where link is reported to be up when SFP+ module is plugged in without cable. This occurs with specific module types which may generate temporary TX_FAULT indication. Solution is to avoid changing any link parameters when checking TX_FAULT indication while physical link is down. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-01bnx2x: Fix Duplex setting for 54618seYaniv Rosner
BCM54618SE is used to advertise half-duplex even if HD was not requested by the user. This change makes the legacy speed/duplex advertisement for this PHY exactly according to the requested speed and duplex. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-01bnx2x: Fix passive DAC cable detectionYaniv Rosner
Fix Passive DAC detection for specific cables, such that even in case SFP_CABLE_TECHNOLOGY option is not set in the EEPROM (offset 8), treat it as a passive DAC cable, since some cables don't have this indication. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-01bnx2x: Fix 578xx-KR 1G linkYaniv Rosner
Fix a problem where 578xx-KR is unable to get link when connected to 1G link partner. Two fixes were required: One was to force CL37 sync_status low to prevent Warpcore from getting stuck in CL73 parallel detect loop while link partner is sending. Second fix was to enable auto-detect mode, thus allowing the Warpcore to select the higher speed protocol between 10G-KR (over CL73), or go down to 1G over CL73 when there's indication for it. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-01sata_sis: missing PM supportAlan
sata_sis has no suspend/resume methods. The default ones will do fine and are needed on some systems. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-01-01Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linuxLinus Torvalds
Pull radeon drm fixes from Dave Airlie: "Just piping a bunch of fixes from pre-xmas from Alex for radeon, all either fix bad hw setup issues or regressions" * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm/radeon: Bump version for CIK DCE tiling fix drm/radeon: set correct number of banks for CIK chips in DCE drm/radeon: set correct pipe config for Hawaii in DCE drm/radeon: expose render backend mask to the userspace drm/radeon: fix render backend setup for SI and CIK drm/radeon: 0x9649 is SUMO2 not SUMO drm/radeon: fix UVD 256MB check
2014-01-01Merge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds
Pull crypto fix from Herbert Xu: "Fix a build error on ARM that was introduced in 3.13-rc1" * git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: ixp4xx - Fix kernel compile error
2014-01-01iio: mxs-lradc: convert is_divided to a bitmapAlexandre Belloni
mxs_lradc.is_divided was an unsigned long array. Convert it to a bitmap to save some memory. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-01-01iio: mxs-lradc: add write_raw function to modify scaleHector Palacios
Added write_raw function to manipulate the optional divider_by_two through the scaling attribute out of the available scales. Signed-off-by: Hector Palacios <hector.palacios@digi.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-01-01iio: mxs-lradc: add scale_available file to channelsHector Palacios
Adds in_voltageX_scale_available file for every channel to read the different available scales. There are two scales per channel: [0] = divider_by_two disabled (default) [1] = divider_by_two enabled The scale is a struct made of integer and nano parts to build a long decimal number. Signed-off-by: Hector Palacios <hector.palacios@digi.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-01-01iio: mxs-lradc: add scale attribute to channelsHector Palacios
Some LRADC channels have fixed pre-dividers and all have an optional divider by two which allows a maximum input voltage of VDDIO - 50mV. This patch - adds the scaling info flag to all channels - grabs the max reference voltage per channel (where the fixed pre-dividers apply) - allows to read the scaling attribute (computed from the Vref) Signed-off-by: Hector Palacios <hector.palacios@digi.com>. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-01-01ASoC: simple-card: Add device's module clock selection.Xiubo Li
Try to get the device's module clock if the dt has no clocks and system-clock-frequency properties. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-01-01iio: add Capella CM32181 ambient light sensor driver.Kevin Tsai
Add Capella Microsystem CM32181 Ambient Light Sensor IIO driver. This driver will convert raw data to lux value under open-air condition. Change the calibscale based on the cover material. Signed-off-by: Kevin Tsai <ktsai@capellamicro.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
2014-01-01Merge branch 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux ↵Dave Airlie
into drm-fixes Radeon fixes, Christmas eve edition. Fix incorrect family for 0x9649 which lead to bogus rendering, tiling and RB fixes for SI and CIK, and a UVD fix. * 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux: drm/radeon: Bump version for CIK DCE tiling fix drm/radeon: set correct number of banks for CIK chips in DCE drm/radeon: set correct pipe config for Hawaii in DCE drm/radeon: expose render backend mask to the userspace drm/radeon: fix render backend setup for SI and CIK drm/radeon: 0x9649 is SUMO2 not SUMO drm/radeon: fix UVD 256MB check
2014-01-01crypto: ixp4xx - Fix kernel compile errorKrzysztof Hałasa
drivers/crypto/ixp4xx_crypto.c: In function 'ixp_module_init': drivers/crypto/ixp4xx_crypto.c:1419:2: error: 'dev' undeclared (first use in this function) Now builds. Not tested on real hw. Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2013-12-31usbnet: mcs7830: rework link state detectionOctavian Purdila
Even with the quirks in commit dabdaf0c (mcs7830: Fix link state detection) there are still spurious link-down events for some chips where the false link-down events count go over a few hundreds. This patch takes a more conservative approach and only looks at link-down events where the link-down state is not combined with other states (e.g. half/full speed, pending frames in SRAM or TX status information valid). In all other cases we assume the link is up. Tested on MCS7830CV-DA (USB ID 9710:7830). Cc: Ondrej Zary <linux@rainbow-software.org> Cc: Michael Leun <lkml20120218@newton.leun.net> Cc: Ming Lei <ming.lei@canonical.com> Signed-off-by: Octavian Purdila <octavian.purdila@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-31Smack: File receive audit correctionCasey Schaufler
Eric Paris politely points out: Inside smack_file_receive() it seems like you are initting the audit field with LSM_AUDIT_DATA_TASK. And then use smk_ad_setfield_u_fs_path(). Seems like LSM_AUDIT_DATA_PATH would make more sense. (and depending on how it's used fix a crash...) He is correct. This puts things in order. Targeted for git://git.gitorious.org/smack-next/kernel.git Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
2013-12-31Smack: Rationalize mount restrictionsCasey Schaufler
The mount restrictions imposed by Smack rely heavily on the use of the filesystem "floor", which is the label that all processes writing to the filesystem must have access to. It turns out that while the "floor" notion is sound, it has yet to be fully implemented and has never been used. The sb_mount and sb_umount hooks only make sense if the filesystem floor is used actively, and it isn't. They can be reintroduced if a rational restriction comes up. Until then, they get removed. The sb_kern_mount hook is required for the option processing. It is too permissive in the case of unprivileged mounts, effectively bypassing the CAP_MAC_ADMIN restrictions if any of the smack options are specified. Unprivileged mounts are no longer allowed to set Smack filesystem options. Additionally, the root and default values are set to the label of the caller, in keeping with the policy that objects get the label of their creator. Targeted for git://git.gitorious.org/smack-next/kernel.git Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
2013-12-31vlan: Fix header ops passthru when doing TX VLAN offload.David S. Miller
When the vlan code detects that the real device can do TX VLAN offloads in hardware, it tries to arrange for the real device's header_ops to be invoked directly. But it does so illegally, by simply hooking the real device's header_ops up to the VLAN device. This doesn't work because we will end up invoking a set of header_ops routines which expect a device type which matches the real device, but will see a VLAN device instead. Fix this by providing a pass-thru set of header_ops which will arrange to pass the proper real device instead. To facilitate this add a dev_rebuild_header(). There are implementations which provide a ->cache and ->create but not a ->rebuild (f.e. PLIP). So we need a helper function just like dev_hard_header() to avoid crashes. Use this helper in the one existing place where the header_ops->rebuild was being invoked, the neighbour code. With lots of help from Florian Westphal. Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-31Merge branches 'pm-cpufreq' and 'pm-cpuidle'Rafael J. Wysocki
* pm-cpufreq: intel_pstate: Fail initialization if P-state information is missing cpufreq: preserve user_policy across suspend/resume cpufreq: Clean up after a failing light-weight initialization * pm-cpuidle: ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
2013-12-31Merge branch 'cpuidle/3.13-fixes' of ↵Rafael J. Wysocki
git://git.linaro.org/people/daniel.lezcano/linux into pm-cpuidle Pull ARM cpuidle fixes for v3.13 from Daniel Lezcano. * 'cpuidle/3.13-fixes' of git://git.linaro.org/people/daniel.lezcano/linux: ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
2013-12-31Merge branches 'acpi-pci-pm' and 'acpi-pci-hotplug'Rafael J. Wysocki
* acpi-pci-pm: PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI * acpi-pci-hotplug: ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug ACPI / PCI / hotplug: Avoid warning when _ADR not present
2013-12-31Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input updates from Dmitry Torokhov: "A fix for a panic in gpio-keys driver when set up with absolute events, a fixup to the new zforce driver and a new keycode definition" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: allocate absinfo data when setting ABS capability Input: define KEY_WWAN for Wireless WAN Input: zforce - fix possible driver hang during suspend
2013-12-31Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6Linus Torvalds
Pull cifs fixes from Steve French: "A few small cifs fixes including two for stable, and fixing a regression introduced by the VFS change to file create" * 'for-linus' of git://git.samba.org/sfrench/cifs-2.6: cifs: set FILE_CREATED cifs: We do not drop reference to tlink in CIFSCheckMFSymlink() Add missing end of line termination to some cifs messages
2013-12-31Input: allocate absinfo data when setting ABS capabilityDmitry Torokhov
We need to make sure we allocate absinfo data when we are setting one of EV_ABS/ABS_XXX capabilities, otherwise we may bomb when we try to emit this event. Rested-by: Paul Cercueil <pcercuei@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-12-31ASoC: imx-spdif: Use snd-soc-dummy CODEC driver to link cardNicolin Chen
This is a quick fix for the below two issues when building spdif as modules. 1) If modprobing modules in order: (Step 1) snd-soc-fsl-spdif -> (Step 2) snd-soc-imx-spdif -> (Step 3) snd-soc-spdif-tx/rx, we will fail to create imx-spdif card and dai link unless we rmmod snd-soc-imx-spdif and modprobe it again due to the execution platform_driver_unregister() in probe() when meeting -EPROBE_DEFER at Step 2. 2) After "imx-spdif sound-spdif.17: dit-hifi <-> 2004000.spdif mapping ok", 'rmmod snd-soc-imx-spdif' would cause kernel dump with warning: WARNING: CPU: 0 PID: 1301 at /home/rmk/git/linux-rmk/fs/sysfs/dir.c:915 sysfs_hash_and_remove+0x84/0x90() sysfs: can not remove 'dapm_widget', no directory This should be caused by disordered resourse releasing of the whole link. And trying to unregister the card and then CODEC dev can't fix this issue. Thus this patch just provides a simple fix to these two bugs by using the snd-soc-dummy in the core instead of seperate snd-soc-spdif-tx/rx so that there's no need to handle the registering and unregistering of CODEC or CODEC dai any more. Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ASoC: core: Fix the DAI name getting.Xiubo Li
From "ASoC: make snd_soc_dai_link more symmetrical", can we see that the name of CPU DAI maybe omitted. If the DAI name is omitted, try to use the component name instead. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31iwlwifi: add new devices for 7265 seriesOren Givon
Add new device / subdevice ID for 7265 series. Fix 2 mistakes on the way. Signed-off-by: Oren Givon <oren.givon@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-31ASoC: rsnd: add SRC (Sampling Rate Converter) supportKuninori Morimoto
This patch adds SRC support to Renesas sound driver. SRC converts sampling rate between codec <-> cpu. It needs special codec chip, or very simple DA/AD converter to use it. This patch was tested via ak4554 codec, and supports Gen1 only at this point. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ASoC: rsnd: tidyup rsnd_ssi_master_clk_start() parameterKuninori Morimoto
Renesas sound has SRC (= Sampling Rate Converter), but, the HW implementation depends on its generation. It was part of SRU on Gen1, and SCU on Gen2. This SCU needs DMA transfer to use it. Current rsnd driver is using it as DMA transfer buffer (= no rate convert), and Gen1 is only supported at this point. This patch cleanup it with focusing about SRC and Gen2 part. ssi clock which is calculated from rsnd_ssi_master_clk_start() should have flexibility since Renesas sound has SRC (= Sampling Rate Converter). But current implementation is using runtime->rate directly. This patch tidyup rsnd_ssi_master_clk_start() parameter as preparation of future SRC support Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ASoC: rsnd: scu cleanup: add rsnd_scu_rate_ctrl()Kuninori Morimoto
Renesas sound has SRC (= Sampling Rate Converter), but, the HW implementation depends on its generation. It was part of SRU on Gen1, and SCU on Gen2. This SCU needs DMA transfer to use it. Current rsnd driver is using it as DMA transfer buffer (= no rate convert), and Gen1 is only supported at this point. This patch cleanup it with focusing about SRC and Gen2 part. rsnd_scu_set_hpbif() is renamed to rsnd_scu_rate_ctrl(), since its naming doesn't indicate the function meaning. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ASoC: rsnd: INT_ENABLE is needed only Gen2Kuninori Morimoto
INT_ENABLE is needed only Gen2. rsnd_mod_write() do nothing on Gen1, but it is confusable. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ASoC: rsnd: add rsnd_scu_transfer_start()Kuninori Morimoto
Renesas sound has SRC (= Sampling Rate Converter), but, the HW implementation depends on its generation. It was part of SRU on Gen1, and SCU on Gen2. This SCU needs DMA transfer to use it. Current rsnd driver is using it as DMA transfer buffer (= no rate convert), and Gen1 is only supported at this point. This patch cleanup it with focusing about SRC and Gen2 part. SRC_CTRL/BUSIF_MODE are used for transfer start. This patch adds rsnd_scu_transfer_start() and merge these Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ASoC: rsnd: route setting is needed only Gen1Kuninori Morimoto
Renesas sound has SRC (= Sampling Rate Converter), but, the HW implementation depends on its generation. It was part of SRU on Gen1, and SCU on Gen2. This SCU needs DMA transfer to use it. Current rsnd driver is using it as DMA transfer buffer (= no rate convert), and Gen1 is only supported at this point. This patch cleanup it with focusing about SRC and Gen2 part. rsnd_scu_set_route() is needed only Gen1. This patch renames it to rsnd_scu_set_route_if_gen1() and it adds comment to rsnd_reg member in order to clarify it is used for Gen1. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ASoC: rsnd: make sure variable name for 44.1kHz/48kHzKuninori Morimoto
This driver is assuming that RBGA is used as source clock of 44.1kHz category, and RBGB is used as source clock of 48kHz category. This patch clarifies the variable name. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ASoC: rsnd: tidyup register namingKuninori Morimoto
Use correct register name which appears in the datasheet Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ASoC: rsnd: tidyup ssi commentKuninori Morimoto
we can check rsnd_ssi_init(), not, rsnd_ssi_start() Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ASoC: rsnd: add rsnd_adg_set_ssi_clk() and cleanup adgKuninori Morimoto
This patch adds rsnd_adg_set_ssi_clk() to access to AUDIO_CLK_SEL0/1/2, and removes last user of rsnd_write/read/bset which is very low level function. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ASoC: hdmi-codec: Add devicetree binding with documentationJyri Sarha
Signed-off-by: Jyri Sarha <jsarha@ti.com> cc: bcousson@baylibre.com Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ASoC: simple-card: Cleanup __asoc_simple_card_dai_init() ret checkXiubo Li
The ret parameter is always equal to zero till here. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplugRafael J. Wysocki
The changes in the ACPI-based PCI hotplug (ACPIPHP) subsystem made during the 3.12 development cycle uncovered a problem with VGA switcheroo that on some systems, when the device-specific method (ATPX in the radeon case, _DSM in the nouveau case) is used to turn off the discrete graphics, the BIOS generates ACPI hotplug events for that device and those events cause ACPIPHP to attempt to remove the device from the system (they are events for a device that was present previously and is not present any more, so that's what should be done according to the spec). Then, the system stops functioning correctly. Since the hotplug events in question were simply silently ignored previously, the least intrusive way to address that problem is to make ACPIPHP ignore them again. For this purpose, introduce a new ACPI device flag, no_hotplug, and modify ACPIPHP to ignore hotplug events for PCI devices whose ACPI companions have that flag set. Next, make the radeon and nouveau switcheroo detection code set the no_hotplug flag for the discrete graphics' ACPI companion. Fixes: bbd34fcdd1b2 (ACPI / hotplug / PCI: Register all devices under the given bridge) References: https://bugzilla.kernel.org/show_bug.cgi?id=61891 References: https://bugzilla.kernel.org/show_bug.cgi?id=64891 Reported-and-tested-by: Mike Lothian <mike@fireburn.co.uk> Reported-and-tested-by: <madcatx@atlas.cz> Reported-and-tested-by: Joaquín Aramendía <samsagax@gmail.com> Cc: Alex Deucher <alexdeucher@gmail.com> Cc: Dave Airlie <airlied@linux.ie> Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
2013-12-31ASoC: simple-card: Add DAPM routes parse from device treeXiubo Li
Parses a simple DAPM route table from device tree. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31intel_pstate: Fail initialization if P-state information is missingRafael J. Wysocki
If pstate.current_pstate is 0 after the initial intel_pstate_get_cpu_pstates(), this means that we were unable to obtain any useful P-state information and there is no reason to continue, so free memory and return an error in that case. This fixes the following divide error occuring in a nested KVM guest: Intel P-state driver initializing. Intel pstate controlling: cpu 0 cpufreq: __cpufreq_add_dev: ->get() failed divide error: 0000 [#1] SMP Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-0.rc4.git5.1.fc21.x86_64 #1 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 task: ffff88001ea20000 ti: ffff88001e9bc000 task.ti: ffff88001e9bc000 RIP: 0010:[<ffffffff815c551d>] [<ffffffff815c551d>] intel_pstate_timer_func+0x11d/0x2b0 RSP: 0000:ffff88001ee03e18 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff88001a454348 RCX: 0000000000006100 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffff88001ee03e38 R08: 0000000000000000 R09: 0000000000000000 R10: ffff88001ea20000 R11: 0000000000000000 R12: 00000c0a1ea20000 R13: 1ea200001ea20000 R14: ffffffff815c5400 R15: ffff88001a454348 FS: 0000000000000000(0000) GS:ffff88001ee00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000000 CR3: 0000000001c0c000 CR4: 00000000000006f0 Stack: fffffffb1a454390 ffffffff821a4500 ffff88001a454390 0000000000000100 ffff88001ee03ea8 ffffffff81083e9a ffffffff81083e15 ffffffff82d5ed40 ffffffff8258cc60 0000000000000000 ffffffff81ac39de 0000000000000000 Call Trace: <IRQ> [<ffffffff81083e9a>] call_timer_fn+0x8a/0x310 [<ffffffff81083e15>] ? call_timer_fn+0x5/0x310 [<ffffffff815c5400>] ? pid_param_set+0x130/0x130 [<ffffffff81084354>] run_timer_softirq+0x234/0x380 [<ffffffff8107aee4>] __do_softirq+0x104/0x430 [<ffffffff8107b5fd>] irq_exit+0xcd/0xe0 [<ffffffff81770645>] smp_apic_timer_interrupt+0x45/0x60 [<ffffffff8176efb2>] apic_timer_interrupt+0x72/0x80 <EOI> [<ffffffff810e15cd>] ? vprintk_emit+0x1dd/0x5e0 [<ffffffff81757719>] printk+0x67/0x69 [<ffffffff815c1493>] __cpufreq_add_dev.isra.13+0x883/0x8d0 [<ffffffff815c14f0>] cpufreq_add_dev+0x10/0x20 [<ffffffff814a14d1>] subsys_interface_register+0xb1/0xf0 [<ffffffff815bf5cf>] cpufreq_register_driver+0x9f/0x210 [<ffffffff81fb19af>] intel_pstate_init+0x27d/0x3be [<ffffffff81761e3e>] ? mutex_unlock+0xe/0x10 [<ffffffff81fb1732>] ? cpufreq_gov_dbs_init+0x12/0x12 [<ffffffff8100214a>] do_one_initcall+0xfa/0x1b0 [<ffffffff8109dbf5>] ? parse_args+0x225/0x3f0 [<ffffffff81f64193>] kernel_init_freeable+0x1fc/0x287 [<ffffffff81f638d0>] ? do_early_param+0x88/0x88 [<ffffffff8174b530>] ? rest_init+0x150/0x150 [<ffffffff8174b53e>] kernel_init+0xe/0x130 [<ffffffff8176e27c>] ret_from_fork+0x7c/0xb0 [<ffffffff8174b530>] ? rest_init+0x150/0x150 Code: c1 e0 05 48 63 bc 03 10 01 00 00 48 63 83 d0 00 00 00 48 63 d6 48 c1 e2 08 c1 e1 08 4c 63 c2 48 c1 e0 08 48 98 48 c1 e0 08 48 99 <49> f7 f8 48 98 48 0f af f8 48 c1 ff 08 29 f9 89 ca c1 fa 1f 89 RIP [<ffffffff815c551d>] intel_pstate_timer_func+0x11d/0x2b0 RSP <ffff88001ee03e18> ---[ end trace f166110ed22cc37a ]--- Kernel panic - not syncing: Fatal exception in interrupt Reported-and-tested-by: Kashyap Chamarthy <kchamart@redhat.com> Cc: Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: All applicable <stable@vger.kernel.org>
2013-12-31doc: cgroups: Fix typo in doc/cgroupsMasanari Iida
Correct spelling typo in memory.txt and resource_counter.txt Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2013-12-31ASoC: atmel: sam9x5_wm8731: remove platform_set_drvdataBo Shen
When call snd_soc_register_card, it will set driver data to this device through dev_set_drvdata, then in driver, no need to call platform_set_drvdata again, so remove it. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ahci: add PCI ID for Marvell 88SE9170 SATA controllerSimon Guinot
This patch adds support for the PCI ID provided by the Marvell 88SE9170 SATA controller. Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org
2013-12-31ASoC: fsl_sai: fix the endianess for SAI fifo data.Xiubo Li
Revert the SAI's endianess for fifo data to/from DMA engine. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ASoC: fsl_sai: Fix one bug for hardware limitation.Xiubo Li
This is maybe one bug or a limitation of the hardware that the {T,R}CR2's Synchronous Mode bits must be set as late as possible, or the SAI device maybe hanged up, and there has not any explaination about this limitation in the SAI Data Sheet. And the {T,R}CR2's Synchronous Mode bits must be set at the same time whether for Tx or Rx stream. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-12-31ata: pata_samsung_cf: Move plat/regs-ata.h to drivers/ataSachin Kamat
plat/regs-ata.h is used only by Samsung PATA driver. Move this file to the drivers folder to remove platform dependency required for multiplatform support. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Reviewed-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2013-12-30Merge tag 'dt-fixes-for-3.13' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux Pull devicetree fixes from Rob Herring: - Fix 2 regressions found on PPC - Allow NULL ptr in unflatten_and_copy_device_tree - Update my email address * tag 'dt-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: MAINTAINERS: Update Rob Herring's email address of/irq: Fix device_node refcount in of_irq_parse_raw() of/Kconfig: Spelling s/one/once/ Revert "of/address: Handle #address-cells > 2 specially" of: Fix NULL dereference in unflatten_and_copy()
generated by cgit (git 2.34.1) at 2025-09-23 13:49:17 +0000