| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds a struct 'fsl_ssi_rxtx_reg_val' which holds register
values necessary to enable rx/tx. Based on those preset register values,
the added configuration functions will cleanly enable/disable different
parts of the SSI IP while supporting online/offline configuration.
Different operating modes can be setup directly as different register
values in fsl_ssi_reg_val.
These functions and structs will help to cleanup and simplify the
trigger function to support many different IP versions (online/offline
configuration) and different operating modes.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
imx50-ssi and later versions of this IP support online reconfiguration
of all registers. The reference manual does not list any registers that
can only be configured while the SSI unit is disabled. This patch
introduces the flag for later use.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
irqs should only be requested/released with enabled DMA. Previously
interrupt statistics where disabled for IMX Processors because of
different writeable SISR bits.
This patch introduces support for irqstats on imx processors again by
creating a sisr writeback mask and introducing a imx35-ssi compatible.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There is a small but significant difference between imx21-ssi and
imx51-ssi and above. imx21-ssi does not allow online reconfiguration of
some registers. They have to be configured at the beginning.
imx51-ssi has to reconfigure the SSI unit while it is running. Otherwise
it would not be possible to have two streams in parallel. The new SDMA
unit in imx51 and above has to be configured before the first DMA
request arrives. Therefor we need to setup TDMAE/RDMAE just before
starting the stream.
This patch introduces distinct imx51-ssi as compatible and adds
of_device_id matching in the probe function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Interrupt statistics of fsl_ssi are mainly for debugging purpose. Most
of those interrupts show error states, e.g. under/overflow.
The stats should be exposed via debugfs instead of sysfs.
This patch moves the statistics file to debugfs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch fixes the error handling in the fsl-ssi probe function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Commit 6d9252bd9a4bb (clk: Add support for power of two type dividers)
merged in v3.6 added the _get_val function to convert a divisor value to
a register field value depending on the flags. However it used the type
u8 for the div field, causing divisors larger than 255 to be masked
and the resultant clock rate to be too high.
E.g. in my case an 11bit divider was supposed to divide 24.576 MHz down
to 32.768KHz. The divisor was correctly calculated as 750 (0x2ee). This
was masked to 238 (0xee) resulting in a frequency of 103.26KHz.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Use macro JUMP_LABEL_TRUE_BRANCH instead of hard-coding for better
readability.
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Optimize jump label implementation for ARM64 by dynamically patching
kernel text.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
As commit a9468f30b5eac6 "ARM: 7333/2: jump label: detect %c
support for ARM", this patch detects the same thing for ARM64
because some ARM64 GCC versions have the same issue.
Some versions of ARM64 GCC which do support asm goto, do not
support the %c specifier. Since we need the %c to support jump
labels on ARM64, detect that too in the asm goto detection script
to avoid build errors with these versions.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Introduce aarch64_insn_gen_{nop|branch_imm}() helper functions, which
will be used to implement jump label on ARM64.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Function encode_insn_immediate() will be used by other instruction
manipulate related functions, so move it into insn.c and rename it
as aarch64_insn_encode_immediate().
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Introduce three interfaces to patch kernel and module code:
aarch64_insn_patch_text_nosync():
patch code without synchronization, it's caller's responsibility
to synchronize all CPUs if needed.
aarch64_insn_patch_text_sync():
patch code and always synchronize with stop_machine()
aarch64_insn_patch_text():
patch code and synchronize with stop_machine() if needed
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Introduce basic aarch64 instruction decoding helper
aarch64_get_insn_class() and aarch64_insn_hotpatch_safe().
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Both patch_realtek.c and patch_conexant.c contain the fairy same code
snippet for supporting Thinkpad ACPI LED controls. Split them into
thinkpad_helper.c and include it from both places. Although this
isn't the best approach from the code size POV, the probability for
coexistence of both Realtek and Conexant codecs on a single machine is
pretty low, thus it'll end up with less memory footprint than
splitting to yet another module.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Properly zero the refcounts and crtc->ddi_pll_set so the previous HW
state doesn't affect the result of reading the current HW state.
This fixes WARNs about WRPLL refcount if we have an HDMI monitor on
HSW and then suspend/resume.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64379
Tested-by: Qingshuai Tian <qingshuai.tian@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Update the documentation also to reflect the fact that there are no ACPI
specific GPIO interfaces anymore but drivers should instead use the
descriptor based GPIO APIs.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that all users of acpi_gpio.h have been moved to use either the GPIO
descriptor interface or to the internal gpiolib.h we can get rid of
acpi_gpio.h entirely.
Once this is done the only interface to get GPIOs to drivers enumerated
from ACPI namespace is the descriptor based interface.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Instead of asking each driver to register to ACPI events we can just call
acpi_gpiochip_register_interrupts() for each chip that has an ACPI handle.
The function checks chip->to_irq and if it is set to NULL (a GPIO driver
that doesn't do interrupts) the function does nothing.
We also add the a new header drivers/gpio/gpiolib.h that is used for
functions internal to gpiolib and add ACPI GPIO chip registering functions
to that header.
Once that is done we can remove call to acpi_gpiochip_register_interrupts()
from its only user, pinctrl-baytrail.c
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The new descriptor based GPIO interface is now the recommended and safer
way of using GPIOs from device drivers. Convert the ACPI SDHCI driver to
use that interface.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
SSM260x also supports 16kHz with external master clocks of 12.000MHz,
12.288MHz and 18.432MHz.
Add matching coefficients, update constraints and announced rates.
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
To avoid another lookup for the twl4030_priv in there.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There's no other users of this functionality, the code can be moved inside
of twl4030_write.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Over time the multi line alignment got messed up. Correct them in one go
so the code will look consistent.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Depend on the regmap reg cache implementation for register caching done in
the twl-core driver.
The local register cache can be removed and we can keep only shadow copies
of certain ctl registers for pop noise reduction.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Few registers need to be cached in the codec driver level. These registers
should only be written when the path is active to avoid pop noise on the
given path.
This patch adds an array which covers the range where the sensitive registers
are located and uppon loadinf the driver the ctl cache will be initialized.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The register states now tracked by the regmap implementation in the core which
makes the reset registers functionality 'redundant' since we know the state
of the registers now all the time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
No need to keep the check defaults functionality anymore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Simplifies the code a bit and prepares it to the removal of local caching.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
asoc-tlw4030
Immutable branch between MFD and ASoC due for the v3.14 merge window
|
|
Makes the code slightly shorter.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Fixes the following sparse warning:
sound/soc/ux500/ux500_msp_i2s.c:649:5: warning:
symbol 'ux500_msp_i2s_of_init_msp' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch adds four new fields to directory leaf blocks.
The intent is not to use them in the kernel itself, although
perhaps we may be able to use them as hints at some later date,
but instead to provide more information for debug/fsck use.
One new field adds a pointer to the inode to which the leaf
belongs. This can be useful if the pointer to the leaf block
has become corrupt, as it will allow us to know which inode
this block should be associated with. This field is set when
the leaf is created and never changed over its lifetime.
The second field is a "distance from the hash table" field.
The meaning is as follows:
0 = An old leaf in which this value has not been set
1 = This leaf is pointed to directly from the hash table
2+ = This leaf is part of a chain, pointed to by another leaf
block, the value gives the position in the chain.
The third and fourth fields combine to give a time stamp of
the most recent directory insertion or deletion from this
leaf block. The time stamp is not updated when a new leaf
block is chained from the current one. The code is currently
written such that the timestamp on the dir inode will match
that of the leaf block for the most recent insertion/deletion.
For backwards compatibility, any of these new fields which is
zero should be considered to be "unknown".
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
The driver defines ADAU1701_SEROCTL_WORD_LEN_16 as 0x10 while it should be b10,
so 0x2. This patch fixes it.
Reported-by: Magnus Reftel <magnus.reftel@lockless.no>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
|
|
Connect the DAPM graph through each BE DAI link to the componnent(s) on the
other side of the BE DAI link. This allows the graph to be walked on
both sides of the link when graph changes are made.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Provide a quick way to tell if a DAI is a dummy DAI or a regular DAI.
This is for internal DAPM usage only and is used to determine whether to
insert a DAI link connection into the DAPM graph.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
When enabling device tree on the S3C an additional build
bug appears in the Osiris DVS board file:
CC arch/arm/mach-s3c24xx/mach-osiris-dvs.o
archh/arm/mach-s3c24xx/mach-osiris-dvs.c:
In function ‘osiris_dvs_notify’:
arch/arm/mach-s3c24xx/mach-osiris-dvs.c:77:4:
error: implicit declaration of function ‘S3C2410_GPB’
[-Werror=implicit-function-declaration]
gpio_set_value(OSIRIS_GPIO_DVS, 1);
^
Fix this by explicitly including
<linux/platform_data/gpio-samsung-s3c24xx.h>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: linux-samsung-soc@vger.kernel.org
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Enable regmap's regcache for the audio registers:
i2c address 0x49, register range 0x01 - 0x49
Mark all other registers as volatile to avoid any side effect for the non
audio functions behind 0x49 i2c address.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
If the regcache is enabled on the regmap module drivers might need to access
to HW register(s) in certain cases in cache bypass mode.
As an example of this is the audio block's ANAMICL register. In normal
operation the content can be cached but during initialization one bit from
the register need to be monitored. With the twl_set_regcache_bypass() the
client driver can switch regcache bypass on and off when it is needed so
we can utilize the regcache for more registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The new twl_get_regmap() function will return a pointer to the regmap needed
for the given module.
Since both read and write function were using the same code to do the lookup
we can reuse this in both places to simplify the code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
For most cases, only a single new block is needed when we reach
the point of converting from stuffed to exhash directory. The
exception being when the file name is so long that it will not
fit within the new leaf block.
So this patch adds a simple test for that situation so that we
do not need to request the full reservation size in this case.
Potentially we could calculate more accurately the value to use
in other cases too, but that is much more complicated to do and
it is doubtful that the benefit would outweigh the extra cost
in code complexity.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
USP0 has multiple functions, and has RX and TX frame sync signals,
for some scenarios like audio PCM, we don't need both of them.
so here we add two possibilities for USP0 only holding one of TX
and RX frame sync.
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
sdmmc5 has only 3 pins CMD, CLK, DATA which are connected with CSR
TriG RF multi-GNSS. The hardware connection is like:
DATA -- GPS_SGN
CLK -- GPS_RF_CLK
CMD -- GPS_MAG
here we drop redundant pins in sdmmc5 group.
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
commit af614b2301f0e304 adds lost USP-based UART pin groups for prima2,
but missed usp1_uart_nostreamctrl group for atlas6, this patch fixes it.
this makes USP(Universal Serial Ports) port1 can work as uart without
stream ctrl.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds the clock output pin functions on the A20.
The 2 pins can output a configurable clock to be used by
external modules. This is used on the CubieTruck, to supply
a 32768 Hz low power clock to the onboard Wifi+BT module.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Antonios Vamporakis <ant@area128.com>
CC: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
AD1986A mic pins (0x1d and 0x1f) share the same widget for controlling
the loopback volume/mute, but the generic parser didn't check it.
This ended up with the duplicated controls for the same effect.
This patch adds the check of the duplication for avoiding it.
After this fix, there will be only one control although it affects
both paths; this remaining issue should be fixed later in a different
patch.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The 3stack pin configs for AD1986A codec had incorrect values that
resulted in broken mic and line-in.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some tags used in the firmware patch file are inconsistent with hwdep
sysfs file names, such as, the firmware patch takes [hint] tag while
sysfs file is */hints. This makes even me referring back to the
document often. Let's provide the same tag names as sysfs for
reducing confusions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Just a code refactoring: the need_codec flag in hda_patch_item struct
can be removed by checking the current mode instead. No functional
change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
