| Age | Commit message (Collapse) | Author |
|---|
|
Since USB connector bindings are available we can describe it on TM2(e).
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add node for the hardware crypto acceleration used in the artpec6 SoC.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The PCIe controller in the artpec6 SoC supports both root complex and
endpoint mode, however, the controller can only be used in one of the
modes.
Both pci nodes are disabled by default. A DTS file can enable one of
them, depending on what mode it wants to run.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add nodes for the nbpfaxi DMA controllers used in the artpec6 SoC,
and start using them for the exising UARTs.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add node for the pin controller used in the artpec6 SoC,
and start using it for the exising UARTs.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The snps,dwc-qos-ethernet binding is still supported as a glue layer
in the stmmac driver.
However, since the snps,dwc-qos-ethernet binding is now deprecated,
migrate to stmmac's native binding.
At the same time, enable features supported by the stmmac driver,
such as PTP, LPI, and an additional tx queue.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Remove 0x prefix from clkctrl unit address.
This silences the following dtc warning:
Warning (unit_address_format):
Node /clkctrl@0xf8000000 unit name should not have leading "0x"
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There has never been an artpec6 devboard produced
with less than 1 GiB RAM.
Increase the default value to 1 GiB RAM, so that we
can netboot with large initramfs without going OOM.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Accesses via 0x80000000 go through the ACP instead of using the DDR
directly.
Unfortunately the ACP has proven to be the cause of complete system
hangs. Disabling the ACP makes these problems go away.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The unit addresses on couple of serial nodes have a leading 0 resulting
in couple of warning messages around simple-bus unit address format
errors when compiled with W=1. Fix the same.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Certain revisions of the TI EMIF IP contain ECC support in them. Reflect
this in the DT binding. Also, add interrupts property as a required
property for the emif controller, as all revisions of the emif IP contain
interrupt support; this might remain unused by the kernel driver though.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Commit 95d8b41c765b ("ARM: dts: keystone-k2e-clocks: Add missing unit
name to clock nodes that have regs") fixed the unit names on various
clock nodes but missed out adding the unit address separator on the
clkhyperlink0 clock node. Fix the same.
Fixes: 95d8b41c765b ("ARM: dts: keystone-k2e-clocks: Add missing unit name to clock nodes that have regs")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The two usb-phy nodes are not memory-mapped devices on the
SoC but rather dummy phys for SoCs with transparent autonomous
NOP phys. Move these to outside soc0 to their own node like
done elsewhere.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
gpio,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
ti,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes warnings about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
gpio,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes warnings about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
gpio,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
gpio,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
ti,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
ti,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The proper name for the property, which assign given device to IOMMU is
'iommus', not 'iommu'. Fix incorrect name and let all GScaler devices
to be properly handled when IOMMU support is enabled.
Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 6cbfdd73a94f ("ARM: dts: add sysmmu nodes for exynos5250")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The bypass-smu property is neither used nor documented in bindings.
Remove it from Xyref5260 board DTS.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
All the devices on I2C0 support fast mode, so increase the bus speed
to match. The Armada 388 is known to have a timing issue when in
standard mode, which we believe causes the ficticious device at 0x64
to appear.
[gregory.clement@bootlin.com: Note that since the commit fbffee74986c
("ARM: dts: Fix I2C repeated start issue on Armada-38x") in 4.14, the
timing issue is managed for the Armada 38x SoCs.]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
dtc now gives the following warning:
arch/arm/boot/dts/kirkwood-t5325.dtb: Warning (sound_dai_property): /sound/simple-audio-card,cpu:sound-dai: property size (4) too small for cell size 1
The binding documentation gives no indication what the cell size should
be (which should be fixed too), so just assume 0 is fine as that is what
the consumer has.
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Replace sdio2 rcc hard coded clock value by its macro.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
STM32F769 SoC provides 2 SDMMC instances, add missing
RCC SDMMC2 entry for it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Adds SDIO related DT nodes for stm32f769-disco board.
broken-cd property is needed as it misses a pullup on board
(resistor R76 is missing).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Adds SDIO related DT nodes for stm32f746-eval board.
broken-cd property is needed as card detect signal is
connected to a GPIO expander which is not yet supported
in kernel linux.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Adds SDIO related DT nodes for stm32f746-disco board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add sdio pins definition for the 2 sdio instances embeds in stm32f746.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds all SPI instances of the STM32H743 SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A small set of fixes for x86:
- Add missing instruction suffixes to assembly code so it can be
compiled by newer GAS versions without warnings.
- Switch refcount WARN exceptions to UD2 as we did in general
- Make the reboot on Intel Edison platforms work
- A small documentation update so text and sample command match"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Documentation, x86, resctrl: Make text and sample command match
x86/platform/intel-mid: Handle Intel Edison reboot correctly
x86/asm: Add instruction suffixes to bitops
x86/entry/64: Add instruction suffix
x86/refcounts: Switch to UD2 for exceptions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/pti fixes from Thomas Gleixner:
"Three fixes related to melted spectrum:
- Sync the cpu_entry_area page table to initial_page_table on 32 bit.
Otherwise suspend/resume fails because resume uses
initial_page_table and triggers a triple fault when accessing the
cpu entry area.
- Zero the SPEC_CTL MRS on XEN before suspend to address a
shortcoming in the hypervisor.
- Fix another switch table detection issue in objtool"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu_entry_area: Sync cpu_entry_area to initial_page_table
objtool: Fix another switch table detection issue
x86/xen: Zero MSR_IA32_SPEC_CTRL before suspend
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A small set of fixes from the timer departement:
- Add a missing timer wheel clock forward when migrating timers off a
unplugged CPU to prevent operating on a stale clock base and
missing timer deadlines.
- Use the proper shift count to extract data from a register value to
prevent evaluating unrelated bits
- Make the error return check in the FSL timer driver work correctly.
Checking an unsigned variable for less than zero does not really
work well.
- Clarify the confusing comments in the ARC timer code"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Forward timer base before migrating timers
clocksource/drivers/arc_timer: Update some comments
clocksource/drivers/mips-gic-timer: Use correct shift count to extract data
clocksource/drivers/fsl_ftm_timer: Fix error return checking
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixlet from Thomas Gleixner:
"Just a documentation update for the missing device tree property of
the R-Car M3N interrupt controller"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dt-bindings/irqchip/renesas-irqc: Document R-Car M3-N support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- when NR_CPUS is large, a SRCU structure can significantly inflate
size of the main filesystem structure that would not be possible to
allocate by kmalloc, so the kvalloc fallback is used
- improved error handling
- fix endiannes when printing some filesystem attributes via sysfs,
this is could happen when a filesystem is moved between different
endianity hosts
- send fixes: the NO_HOLE mode should not send a write operation for a
file hole
- fix log replay for for special files followed by file hardlinks
- fix log replay failure after unlink and link combination
- fix max chunk size calculation for DUP allocation
* tag 'for-4.16-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix log replay failure after unlink and link combination
Btrfs: fix log replay failure after linking special file and fsync
Btrfs: send, fix issuing write op when processing hole in no data mode
btrfs: use proper endianness accessors for super_copy
btrfs: alloc_chunk: fix DUP stripe size handling
btrfs: Handle btrfs_set_extent_delalloc failure in relocate_file_extent_cluster
btrfs: handle failure of add_pending_csums
btrfs: use kvzalloc to allocate btrfs_fs_info
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"A driver fix and a documentation fix (which makes dependency handling
for the next cycle easier)"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: octeon: Prevent error message on bus error
dt-bindings: at24: sort manufacturers alphabetically
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A 4.16 regression fix, three fixes for -stable, and a cleanup fix:
- During the merge window support for the new ACPI NVDIMM Platform
Capabilities structure disabled support for "deep flush", a
force-unit- access like mechanism for persistent memory. Restore
that mechanism.
- VFIO like RDMA is yet one more memory registration / pinning
interface that is incompatible with Filesystem-DAX. Disable long
term pins of Filesystem-DAX mappings via VFIO.
- The Filesystem-DAX detection to prevent long terms pins mistakenly
also disabled Device-DAX pins which are not subject to the same
block- map collision concerns.
- Similar to the setup path, softlockup warnings can trigger in the
shutdown path for large persistent memory namespaces. Teach
for_each_device_pfn() to perform cond_resched() in all cases.
- Boaz noticed that the might_sleep() in dax_direct_access() is stale
as of the v4.15 kernel.
These have received a build success notification from the 0day robot,
and the longterm pin fixes have appeared in -next. However, I recently
rebased the tree to remove some other fixes that need to be reworked
after review feedback.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
memremap: fix softlockup reports at teardown
libnvdimm: re-enable deep flush for pmem devices via fsync()
vfio: disable filesystem-dax page pinning
dax: fix vma_is_fsdax() helper
dax: ->direct_access does not sleep anymore
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- suppress sparse warnings about unknown attributes
- fix typos and stale comments
- fix build error of arch/sh
- fix wrong use of ld-option vs cc-ldoption
- remove redundant GCC_PLUGINS_CFLAGS assignment
- fix another memory leak of Kconfig
- fix line number in error messages of Kconfig
- do not write confusing CONFIG_DEFCONFIG_LIST out to .config
- add xstrdup() to Kconfig to handle memory shortage errors
- show also a Debian package name if ncurses is missing
* tag 'kbuild-fixes-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
MAINTAINERS: take over Kconfig maintainership
kconfig: fix line number in recursive inclusion error message
Coccinelle: memdup: Fix typo in warning messages
kconfig: Update ncurses package names for menuconfig
kbuild/kallsyms: trivial typo fix
kbuild: test --build-id linker flag by ld-option instead of cc-ldoption
kbuild: drop superfluous GCC_PLUGINS_CFLAGS assignment
kconfig: Don't leak choice names during parsing
sh: fix build error for empty CONFIG_BUILTIN_DTB_SOURCE
kconfig: set SYMBOL_AUTO to the symbol marked with defconfig_list
kconfig: add xstrdup() helper
kbuild: disable sparse warnings about unknown attributes
Makefile: Fix lying comment re. silentoldconfig
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- some build fixes with randconfigs
- an m88ds3103 fix to prevent an OOPS if the chip doesn't provide the
right version during probe (with can happen if the hardware hangs)
- a potential out of array bounds reference in tvp5150
- some fixes and improvements in the DVB memory mapped API (added for
kernel 4.16)
* tag 'media/v4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: vb2: Makefile: place vb2-trace together with vb2-core
media: Don't let tvp5150_get_vbi() go out of vbi_ram_default array
media: dvb: update buffer mmaped flags and frame counter
media: dvb: add continuity error indicators for memory mapped buffers
media: dmxdev: Fix the logic that enables DMA mmap support
media: dmxdev: fix error code for invalid ioctls
media: m88ds3103: don't call a non-initalized function
media: au0828: add VIDEO_V4L2 dependency
media: dvb: fix DVB_MMAP dependency
media: dvb: fix DVB_MMAP symbol name
media: videobuf2: fix build issues with vb2-trace
media: videobuf2: Add VIDEOBUF2_V4L2 Kconfig option for VB2 V4L2 part
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
- rave-sp: add NVMEM dependency
- build fixes for i6300esb_wdt, xen_wdt and sp5100_tco
* tag 'linux-watchdog-4.16-fixes-1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: sp5100_tco.c: fix potential build failure
watchdog: xen_wdt: fix potential build failure
watchdog: i6300esb: fix build failure
watchdog: rave-sp: add NVMEM dependency
|
|
Pull KVM fixes from Radim Krčmář:
"x86:
- fix NULL dereference when using userspace lapic
- optimize spectre v1 mitigations by allowing guests to use LFENCE
- make microcode revision configurable to prevent guests from
unnecessarily blacklisting spectre v2 mitigation feature"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix vcpu initialization with userspace lapic
KVM: X86: Allow userspace to define the microcode version
KVM: X86: Introduce kvm_get_msr_feature()
KVM: SVM: Add MSR-based feature support for serializing LFENCE
KVM: x86: Add a framework for supporting MSR-based features
|
|
The cond_resched() currently in the setup path needs to be duplicated in
the teardown path. Rather than require each instance of
for_each_device_pfn() to open code the same sequence, embed it in the
helper.
Link: https://github.com/intel/ixpdimm_sw/issues/11
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Fixes: 71389703839e ("mm, zone_device: Replace {get, put}_zone_device_page()...")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Re-enable deep flush so that users always have a way to be sure that a
write makes it all the way out to media. Writes from the PMEM driver
always arrive at the NVDIMM since movnt is used to bypass the cache, and
the driver relies on the ADR (Asynchronous DRAM Refresh) mechanism to
flush write buffers on power failure. The Deep Flush mechanism is there
to explicitly write buffers to protect against (rare) ADR failure. This
change prevents a regression in deep flush behavior so that applications
can continue to depend on fsync() as a mechanism to trigger deep flush
in the filesystem-DAX case.
Fixes: 06e8ccdab15f4 ("acpi: nfit: Add support for detect platform CPU cache...")
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
I have recently picked up Kconfig patches to my tree without any
declaration. Making it official now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Filesystem-DAX is incompatible with 'longterm' page pinning. Without
page cache indirection a DAX mapping maps filesystem blocks directly.
This means that the filesystem must not modify a file's block map while
any page in a mapping is pinned. In order to prevent the situation of
userspace holding of filesystem operations indefinitely, disallow
'longterm' Filesystem-DAX mappings.
RDMA has the same conflict and the plan there is to add a 'with lease'
mechanism to allow the kernel to notify userspace that the mapping is
being torn down for block-map maintenance. Perhaps something similar can
be put in place for vfio.
Note that xfs and ext4 still report:
"DAX enabled. Warning: EXPERIMENTAL, use at your own risk"
...at mount time, and resolving the dax-dma-vs-truncate problem is one
of the last hurdles to remove that designation.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org>
Reported-by: Haozhong Zhang <haozhong.zhang@intel.com>
Tested-by: Haozhong Zhang <haozhong.zhang@intel.com>
Fixes: d475c6346a38 ("dax,ext2: replace XIP read and write with DAX I/O")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Update pci.ids location (documentation only) (Randy Dunlap)
- Fix a crash when BIOS didn't assign a BAR and we try to enlarge it
(Christian König)
* tag 'pci-v4.16-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Allow release of resources that were never assigned
PCI: Update location of pci.ids file
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
- a patch to change the ordering of cache and TLB flushes to hopefully
fix the random segfaults we very rarely face (by Dave Anglin).
- a patch to hide the virtual kernel memory layout due to security
reasons.
- two small patches to make the kernel run more smoothly under qemu.
* 'parisc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Reduce irq overhead when run in qemu
parisc: Use cr16 interval timers unconditionally on qemu
parisc: Check if secondary CPUs want own PDC calls
parisc: Hide virtual kernel memory layout
parisc: Fix ordering of cache and TLB flushes
|
|
Add sound support to Motorola Droid 4 using simple-soundcard
and CPCAP's audio codec. This does not yet correctly represent
the whole audio routing, since McBSP3 is also connected to
Bluetooth and MDM6600 modem (and probably also 4G modem).
These extra DAI links are not yet supported and have not been
tested.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
