| Age | Commit message (Collapse) | Author |
|---|
|
Remove pullup on uart TX signals, they are push-pull outputs thus
pullups are pointless.
Add pullup on uart RX signals, they prevent the RX signals to be left
floating and so consuming a useless extra amount of power in crowbarred
state if nothing is connected to RX.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
There are only 19 PIOB pins having primary names PB0-PB18. Not all of them
have a 'C' function. So the pinctrl property mask ends up being the same as the
other SoC of the at91sam9x5 series.
Reported-by: Marek Sieranski <marek.sieranski@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Update the "gpio-ranges" property of the CBUS GPIO controller on Meson8b
because it only provides 83 GPIOs.
The GPIO definitions in include/dt-bindings/gpio/meson8b-gpio.h
inherited all GPIOs from Meson8 until recently. However, Meson8b does
not support all GPIOs which are supported by Meson8 (Meson8b doesn't
have a GPIOZ bank, most of the pins from the GPIODV bank are missing on
Meson8b - just to name a few differences).
The actual number of GPIOs is only 83, instead of 120 from Meson8 plus
the 10 GPIOs from the DIF bank on Meson8b.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The Odroid C1 features a microSD slot. This patch adds the necessary
DT bindings to support it.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
These are needed to use the n_gsm driver for TS 27.010 UART
multiplexing. Note that support for the OOB wake gpio is still
missing so the UART is not yet usable for n_gsm.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Configure MDM6600 USB PHY.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We have a USB OCHI PHY on port 1 for mdm6600. Port 2 is using transceiverless
logic (TLL) for USB EHCI for w3glte modem.
Let's also fix the node name to use usb-phy while at it.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The xref_xtal clock is used by twl6040 as mclk. It is needed for the HPPLL
internally.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The clock is directly sourced from sys_clkin, and provides an external
output clock for (typically) TWL6040 chip.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The pad configuration area under control module wkup has some miscellaneous
config registers, that are not pinmux related. Add a separate area for
these, and add support for syscon / clocks under this new area.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The pad configuration area under control module wkup has some miscellaneous
config registers, that are not pinmux related.
Add new compatible string for this section of control module.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
USB1 port is micro-AB type and can function as peripheral
as well as host. Enable dual-role mode for USB1.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The Xunlong Orange Pi Zero Plus is single board computer.
- H5 Quad-core 64-bit Cortex-A53
- 512MB DDR3
- microSD slot
- Debug TTL UART
- 1000M/100M/10M Ethernet RJ45
- Realtek RTL8189FTV
- Spi flash (2MB)
- One USB 2.0 HOST, One USB 2.0 OTG
This is based on a patch from armbian:
https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This adds the actual VGA DAC bridge that is used in the
Versatile AB, and sets the mode to 640x480 VGA.
The "clcd" clock was incorrectly named, the proper name
(from bindings) is "clcdclk". So far drivers survived
by just getting the first clock, but future drivers will
use named clocks.
We add the panel connector to the
"arm,versatile-tft-panel" as well, the signals actually
fork on the board, reaching both the VGA DAC and the
display connector.
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Versatile board can be equipped with a interface board
just named "IB2". This was created in the early 2000s for
prototyping GSM candybar phone form factor products.
The IB2 board contains:
- Cascaded interrupt controller
- Enfora Enabler GSM0308 quad-band module with antenna and
separate audio jack
- Keypad with joystick
- Sanyo 2.5" color display
- A 28-pin connector for mounting a camera
This adds a DTS file for the combination of the Versatile AB
with an IB2 daughterboard mounted, making the LED blink and
making the system controller available for drivers, such as
the panel driver.
The device tree bindings already exist in
Documentation/devicetree/bindings/arm/arm-boards.
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PL111 in the ARM reference platforms are connected to
"panels" that are actually dumb VGA DAC connector bridges.
Now that we can support the proper bridges in the DRM driver,
fix this up.
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
efuse is one time programmable, so it is safer to deny write request
to this memory, unless the user is savvy enough to remove the read-only
flag from DTB
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The Mali-450 IP can run up to 744MHz, bump the frequency using
the GP0 PLL clock.
Cc: Michal Lazo <michal.lazo@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The Cubieboard4 has a dumb VGA DAC connected to the output of LCD0,
providing VGA output through the onboard VGA connector. The DDC lines
are connected to i2c3.
The VGA DAC is a GM7123, which is compatible with Analog Devices'
ADV7123, except it only takes 3.3V power, and has a lower standby power
consumption. The datasheet found online lists "Chengdu GoldTel Electronical
Technology Co., Ltd." as its designer. The company changed its name in
2014 to "Chengdu Corpro Technology Co., Ltd.". Their website lists similar
ICs, but not actually the GM7123.
Enable the display pipeline with the VGA DAC and connector, and i2c3
for DDC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The A80 supports RGB888 with H/V sync from LCD0. Add a pinmux setting
for the needed pins.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Allwinner A80 SoC has 3 display pipelines, of which some parts are
documented:
- 3x display front ends (FE), documented
- 2x display enhancement units (DEU), undocumented
- 3x display back ends (BE), documented
- 2x dynamic range controller (DRC), undocumented
- 2x LCDC/TCONs, documented
- 1x LCDC/TCON, undocumented, and probably not useable
- 1x HDMI transmitter, undocumented but DesignWare compatible
- 1x MERGE block, function unknown
This patch adds device nodes for the first 2 documented pipelines:
FE0 - DEU0 - - BE0 - DRC0 - TCON0
x
FE1 - DEU1 - - BE1 - DRC1 - TCON1
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The TERES-I is an open hardware laptop built by Olimex using the
Allwinner A64 SoC.
Add the board specific .dts file, which includes the A64 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The A64 SoC features two display pipelines, one has a LCD output, the
other has a HDMI output.
Add support for simplefb for the LCD output. Tested on Teres I.
This patch was inspired by work of Icenowy Zheng.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add a watchdog node for the A64, automatically enabled on all boards.
Since the device is compatible with an existing driver, we only reserve
a new compatible string to be used together with the fall back.
Tested on Olimex Teres-I.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add the proper pin group node to reference in board files.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Pine H64 is an Allwinner H6-based SBC from Pine64, with the following
features:
- 1GiB/2GiB/4GiB LPDDR3 DRAM (in 4GiB situation only 3GiB is
accessible)
- AXP805 PMIC
- Raspberry-Pi-compatible GPIO header, "Euler" GPIO header (not
compatible with the "Euler" on Pine A64) and "Expansion" pin header
- 2 USB 2.0 ports and 1 USB 3.0 ports
- Audio jack
- MicroSD slot and eMMC module slot
- on-board SPI NOR flash
- 1Gbps Ethernet port (via RTL8211E PHY)
- HDMI port
Adds initial support for it, including the UART on the Expansion pin
header.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Allwinner H6 is a new SoC with Cortex-A53 cores from Allwinner, with its
memory map fully reworked and some high-speed peripherals (PCIe, USB
3.0) introduced.
This commit adds the basical DTSI file of it, including the clock
support and UART support.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The schematic of the espressobin is publicly available, add a comment
where to find it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This extra clock is needed to access the registers of the PCIe host
controller used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "PCI: armada8k: Fix clock resource by adding
a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This extra clock is needed to access the registers of the NAND controller
used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "mtd: nand: marvell: Fix clock resource by adding
a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This extra clock is needed to access the registers of the safexcel EIP97
used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "crypto: inside-secure - fix clock resource by
adding a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This extra clock is needed to access the registers of the harware RNG
used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "hwrng: omap - Fix clock resource by adding a
register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This extra clock is needed to access the registers of the XOR engine
controller used on CP110 component of the Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "dmaengine: mv_xor_v2: Fix clock resource by
adding a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This extra clock is needed to access the registers of the USB host
controller used on Armada 7K/8K SoCs.
This follow the changes already made in the binding documentation (as
well as in the driver): "usb: host: xhci-plat: Fix clock resource by
adding a register clock"
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Add auxadc device node for MT2712.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
This patch adds some device nodes for the PCIe function block and updates
related pinmux.
Moreover, we add interrupt-map properties in both parent and children as
the chip only has one IRQ per slot that is connected to all INTx and get
propagated through the bridges and it also represents the root ports own
interrupts.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The H3 has an ARM Mali 400 GPU, so add binding to our DT.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
It should be good that no use "_" is in DT node name. Consequently,
those nodes in certain files which have an inappropriate name containing
"_" are all being replaced with "-".
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The property pinctrl-names is totally superfluous. It would be good to
remove the property to keep the node neatness. There is actually
unnecessary to set up any pins for data path TRGMII between main SoC and
MT7530. Furthermore, it's more reasonable for the pin setup of control
path MDIO bus is being placed inside the node of ethernet controller.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Complement the missing clock properties cpu[1-3] should depend on.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linux-pm@vger.kernel.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
On bpi-r2 board, totally there're four UARTs which we usually called
uart[0-3] helpful to extend slow-I/O devices. Among those ones, uart2 has
dedicated pin slot which is used to console log. uart[0-1] appear at the
40-pins connector and uart3 has no pinout, but just has test points (TP47
for TX and TP48 for RX, respectively) nearby uart2, but we don't enable
uart3 in the patch. The missing pinctrl is also being supplemented for
those newly added devices.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Both mmc devices on bananapi-r2 board should all use the fixed regulators
as their power source instead of PMIC MT6323 exports.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
All ethsys, pciesys and ssusbsys internally include reset controller, so
explicitly add back these missing cell definitions to related bindings
and examples.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Extend the Silk board support to include SW3, SW4, SW6 and SW12. They
are all connected via GPIO lines and handled by the gpio-keys driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Extend the Silk board support to include U14 which is an I2C based EEPROM
hooked up to the I2C1 bus.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for the on-board voltage regulator hooked up to GPIO3_20
on r8a7779 Marzen. The board schematics describes the regulator as U4
TPS2110A. Input wise, U4 has D0 fixed to ground, D1 tied to GPIO3_20
while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V. OUT goes to the
pull-ups for the data pins of SDHI0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Stout base board support making use of 1 GiB of memory,
the Renesas H2 r8a7790 SoC with the SCIFA0 serial port
and CA15 with ARM architected timer.
Furthermore, this device tree contains entries for:
- 4x LEDs
- SDHI SD/MMC controller
- Display unit with HDMI output
- SH fast ethernet controller
- QSPI controller with S25FL512S attached to it
- I2C controller with DA9210 and DA 9063 PMICs
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
