| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds SDIO related DT nodes for stm32429i-eval board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds SDIO-related DT nodes required by stm32f469 board
There is a hardware issue on these boards, it misses a pullup on
the GPIO line used as card detect to allow correct SD card
detection. To allow correct card detection "broken-cd" property
is used.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
wake_klogd is a local variable in console_unlock(). The information
is lost when the console_lock owner using the busy wait added by
the commit dbdda842fe96f8932 ("printk: Add console owner and waiter
logic to load balance console writes"). The following race is
possible:
CPU0 CPU1
console_unlock()
for (;;)
/* calling console for last message */
printk()
log_store()
log_next_seq++;
/* see new message */
if (seen_seq != log_next_seq) {
wake_klogd = true;
seen_seq = log_next_seq;
}
console_lock_spinning_enable();
if (console_trylock_spinning())
/* spinning */
if (console_lock_spinning_disable_and_check()) {
printk_safe_exit_irqrestore(flags);
return;
console_unlock()
if (seen_seq != log_next_seq) {
/* already seen */
/* nothing to do */
Result: Nobody would wakeup klogd.
One solution would be to make a global variable from wake_klogd.
But then we would need to manipulate it under a lock or so.
This patch wakes klogd also when console_lock is passed to the
spinning waiter. It looks like the right way to go. Also userspace
should have a chance to see and store any "flood" of messages.
Note that the very late klogd wake up was a historic solution.
It made sense on single CPU systems or when sys_syslog() operations
were synchronized using the big kernel lock like in v2.1.113.
But it is questionable these days.
Fixes: dbdda842fe96f8932 ("printk: Add console owner and waiter logic to load balance console writes")
Link: http://lkml.kernel.org/r/20180226155734.dzwg3aovqnwtvkoy@pathway.suse.cz
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-kernel@vger.kernel.org
Cc: Tejun Heo <tj@kernel.org>
Suggested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
This patch adds the pin configuration for SDIO controller on
stm32f4.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
stm32f429 embeds ARM_PL180 sdi IP, adds SDIO controller
node to allow MMC support.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
stm32f746 embeds ARM_PL180 sdio IP, adds SDIO controller
nodes to allow MMC support.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Tuning can leave the IP in an active state (Buffer Read Enable bit set)
which prevents the entry to low power states (i.e. S0i3). Data reset will
clear it.
Generally tuning is followed by a data transfer which will anyway sort out
the state, so it is rare that S0i3 is actually prevented.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
of_get_named_gpiod_flags() used directly in of_find_gpio() or indirectly
through of_find_spi_gpio() or of_find_regulator_gpio() can return
-EPROBE_DEFER. This gets overwritten by the subsequent of_find_*_gpio()
calls.
This patch fixes this by trying of_find_spi_gpio() or
of_find_regulator_gpio() only if deferred probing was not requested by
the previous of_get_named_gpiod_flags() call.
Fixes: 6a537d48461d ("gpio: of: Support regulator nonstandard GPIO properties")
Fixes: c85823390215 ("gpio: of: Support SPI nonstandard GPIO properties")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[Augmented to fit with Maxime's patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commits c85823390215 ("gpio: of: Support SPI nonstandard GPIO properties")
and 6a537d48461d ("gpio: of: Support regulator nonstandard GPIO
properties") have introduced a regression in the way error codes from
of_get_named_gpiod_flags are handled.
Previously, those errors codes were returned immediately, but the two
commits mentioned above are now overwriting the error pointer, meaning that
whatever value has been returned will be dropped in favor of whatever the
two new functions will return.
This might not be a big deal except for EPROBE_DEFER, on which GPIOlib
customers will depend on, and that will now be returned as an hard error
which means that they will not probe anymore, instead of gently deferring
their probe.
Since EPROBE_DEFER basically means that we have found a valid property but
there was no GPIO controller registered to handle it, fix this issues by
returning it as soon as we encounter it.
Fixes: c85823390215 ("gpio: of: Support SPI nonstandard GPIO properties")
Fixes: 6a537d48461d ("gpio: of: Support regulator nonstandard GPIO properties")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[Fold in fix to the fix]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The compatible property of the root node in a DTS for Atmark Techno
Armadillo-800 EVA should include the compatible value for the R-Mobile
A1 SoC, too.
Fixes: d2c2a0776899ba2d ("ARM: shmobile: Add platform device tree bindings documentation")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This exposes to mesa that it can use the fixed ioctl for querying
later cap sets, cap set 1 is forever frozen in time.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180221015003.22884-1-airlied@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. If a bit does
flip it could cause an overrun if it's in one of the size parameters,
so sanity check that we're not overrunning the provided buffer when
doing a memcpy().
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
the bus
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
Update .gitignore with new test.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
Silence the following command being printed while running test.
./mem-on-off-test.sh -r 2 && echo "selftests: memory-hotplug [PASS]" ||
echo "selftests: memory-hotplug [FAIL]"
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
The Makefile lacks a couple of line continuation backslashes
in an `if' clause, which produces an error when make versions
prior to 4.x are used for building the tests.
$ make
make[1]: Entering directory `/[...]/linux/tools/testing/selftests/futex'
/bin/sh: -c: line 5: syntax error: unexpected end of file
make[1]: *** [all] Error 1
make[1]: Leaving directory `/[...]/linux/tools/testing/selftests/futex'
make: *** [all] Error 2
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
Since commit 9273083a1530 ("usb: dwc2: Fix TxFIFOn sizes and total TxFIFO
size issues") we could use the OTG mode again.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Add BCM43438 (bluetooth) as a serdev slave device of uart0 (pl011/ttyAMA0).
This allows to automatically insert the bcm43438 to the bluetooth
subsystem instead of relying on patched userspace helpers (hciattach).
In order to keep a debug UART we need to switch to uart1.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Instead of keeping the firmware's pull settings, we better apply
them via the devicetree pin control. Start with the RPi Zero W relevant
first to keep the effort low.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Commit 343a8d17fa8d (cpufreq: scpi: remove arm_big_little dependency)
removed the SCPI cpufreq dependency on arm_big_little cpufreq driver.
However the Kconfig entry still depends on ARM_BIG_LITTLE_CPUFREQ
which is clearly wrong.
This patch removes that unnecessary Kconfig dependency.
Fixes: 343a8d17fa8d (cpufreq: scpi: remove arm_big_little dependency)
Reported-by: Quentin Perret <quentin.perret@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 343a8d17fa8d (cpufreq: scpi: remove arm_big_little dependency)
changed the cpufreq driver on juno from arm_big_little to scpi.
The scpi set_target function does not call the frequency-invariance
setter function arch_set_freq_scale() like the arm_big_little set_target
function does. As a result the task scheduler load and utilization
signals are not frequency-invariant on this platform anymore.
Fix this by adding a call to arch_set_freq_scale() into
scpi_cpufreq_set_target().
Fixes: 343a8d17fa8d (cpufreq: scpi: remove arm_big_little dependency)
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull idr fixes from Matthew Wilcox:
"One test-suite build fix for you and one run-time regression fix.
The regression fix includes new tests to make sure they don't pop back
up."
* 'idr-2018-02-06' of git://git.infradead.org/users/willy/linux-dax:
idr: Fix handling of IDs above INT_MAX
radix tree test suite: Fix build
|
|
It is entirely possible that the BIOS wasn't able to assign resources to a
device. In this case don't crash in pci_release_resource() when we try to
resize the resource.
Fixes: 8bb705e3e79d ("PCI: Add pci_resize_resource() for resizing BARs")
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
CC: stable@vger.kernel.org # v4.15+
|
|
This stops the driver from trying to probe the ATA slave
interface. The vendor code enables the slave interface
but the driver in the vendor tree does not make use of
it.
Setting it to muxmode 0 disables the slave interface:
the hardware only has the master interface connected
to the one harddrive slot anyways.
Without this change booting takes excessive time, so it
is very annoying to end users.
Fixes: dd5c0561db75 ("ARM: dts: Add basic devicetree for D-Link DNS-313")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The CONFIG_LIRC symbol has changed from 'tristate' to 'bool, so we now
get a warning for omap2plus_defconfig:
arch/arm/configs/omap2plus_defconfig:322:warning: symbol value 'm' invalid for LIRC
This changes the file to mark the symbol as built-in to get rid of the
warning.
Fixes: a60d64b15c20 ("media: lirc: lirc interface should not be a raw decoder")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Gerd reports that ->i_mode may contain other bits besides S_IFCHR. Use
S_ISCHR() instead. Otherwise, get_user_pages_longterm() may fail on
device-dax instances when those are meant to be explicitly allowed.
Fixes: 2bb6d2837083 ("mm: introduce get_user_pages_longterm")
Cc: <stable@vger.kernel.org>
Reported-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Jane Chu <jane.chu@oracle.com>
Reported-by: Haozhong Zhang <haozhong.zhang@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
In Patch:
[7a862fb] brd: remove dax support
Dan Williams has removed the only might_sleep
implementation of ->direct_access.
So we no longer need to check for it.
CC: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Boaz Harrosh <boazh@netapp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Khalid reported that the kernel selftests are currently failing:
selftests: test_bpf.sh
========================================
test_bpf: [FAIL]
not ok 1..8 selftests: test_bpf.sh [FAIL]
He bisected it to 6ce711f2750031d12cec91384ac5cfa0a485b60a ("idr: Make
1-based IDRs more efficient").
The root cause is doing a signed comparison in idr_alloc_u32() instead
of an unsigned comparison. I went looking for any similar problems and
found a couple (which would each result in the failure to warn in two
situations that aren't supposed to happen).
I knocked up a few test-cases to prove that I was right and added them
to the test-suite.
Reported-by: Khalid Aziz <khalid.aziz@oracle.com>
Tested-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
|
|
'struct blk_user_trace_setup' is passed to BLKTRACESETUP, not
BLKTRACESTART.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fix from Borislav Petkov:
"sb_edac: Prevent memory corruption on KNL (from Anna Karbownik)"
* tag 'edac_fixes_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, sb_edac: Fix out of bound writes during DIMM configuration on KNL
|
|
When specifying string type mount option (e.g., logdev)
several times in a mount, current option parsing may
cause memory leak. Hence, call kfree for previous one
in this case.
Signed-off-by: Chengguang Xu <cgxu519@icloud.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Yet another pile of melted spectrum related changes:
- sanitize the array_index_nospec protection mechanism: Remove the
overengineered array_index_nospec_mask_check() magic and allow
const-qualified types as index to avoid temporary storage in a
non-const local variable.
- make the microcode loader more robust by properly propagating error
codes. Provide information about new feature bits after micro code
was updated so administrators can act upon.
- optimizations of the entry ASM code which reduce code footprint and
make the code simpler and faster.
- fix the {pmd,pud}_{set,clear}_flags() implementations to work
properly on paravirt kernels by removing the address translation
operations.
- revert the harmful vmexit_fill_RSB() optimization
- use IBRS around firmware calls
- teach objtool about retpolines and add annotations for indirect
jumps and calls.
- explicitly disable jumplabel patching in __init code and handle
patching failures properly instead of silently ignoring them.
- remove indirect paravirt calls for writing the speculation control
MSR as these calls are obviously proving the same attack vector
which is tried to be mitigated.
- a few small fixes which address build issues with recent compiler
and assembler versions"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
KVM/VMX: Optimize vmx_vcpu_run() and svm_vcpu_run() by marking the RDMSR path as unlikely()
KVM/x86: Remove indirect MSR op calls from SPEC_CTRL
objtool, retpolines: Integrate objtool with retpoline support more closely
x86/entry/64: Simplify ENCODE_FRAME_POINTER
extable: Make init_kernel_text() global
jump_label: Warn on failed jump_label patching attempt
jump_label: Explicitly disable jump labels in __init code
x86/entry/64: Open-code switch_to_thread_stack()
x86/entry/64: Move ASM_CLAC to interrupt_entry()
x86/entry/64: Remove 'interrupt' macro
x86/entry/64: Move the switch_to_thread_stack() call to interrupt_entry()
x86/entry/64: Move ENTER_IRQ_STACK from interrupt macro to interrupt_entry
x86/entry/64: Move PUSH_AND_CLEAR_REGS from interrupt macro to helper function
x86/speculation: Move firmware_restrict_branch_speculation_*() from C to CPP
objtool: Add module specific retpoline rules
objtool: Add retpoline validation
objtool: Use existing global variables for options
x86/mm/sme, objtool: Annotate indirect call in sme_encrypt_execute()
x86/boot, objtool: Annotate indirect jump in secondary_startup_64()
x86/paravirt, objtool: Annotate indirect calls
...
|
|
Pull KVM fixes from Paolo Bonzini:
"s390:
- optimization for the exitless interrupt support that was merged in 4.16-rc1
- improve the branch prediction blocking for nested KVM
- replace some jump tables with switch statements to improve expoline performance
- fixes for multiple epoch facility
ARM:
- fix the interaction of userspace irqchip VMs with in-kernel irqchip VMs
- make sure we can build 32-bit KVM/ARM with gcc-8.
x86:
- fixes for AMD SEV
- fixes for Intel nested VMX, emulated UMIP and a dump_stack() on VM startup
- fixes for async page fault migration
- small optimization to PV TLB flush (new in 4.16-rc1)
- syzkaller fixes
Generic:
- compiler warning fixes
- syzkaller fixes
- more improvements to the kvm_stat tool
Two more small Spectre fixes are going to reach you via Ingo"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (40 commits)
KVM: SVM: Fix SEV LAUNCH_SECRET command
KVM: SVM: install RSM intercept
KVM: SVM: no need to call access_ok() in LAUNCH_MEASURE command
include: psp-sev: Capitalize invalid length enum
crypto: ccp: Fix sparse, use plain integer as NULL pointer
KVM: X86: Avoid traversing all the cpus for pv tlb flush when steal time is disabled
x86/kvm: Make parse_no_xxx __init for kvm
KVM: x86: fix backward migration with async_PF
kvm: fix warning for non-x86 builds
kvm: fix warning for CONFIG_HAVE_KVM_EVENTFD builds
tools/kvm_stat: print 'Total' line for multiple events only
tools/kvm_stat: group child events indented after parent
tools/kvm_stat: separate drilldown and fields filtering
tools/kvm_stat: eliminate extra guest/pid selection dialog
tools/kvm_stat: mark private methods as such
tools/kvm_stat: fix debugfs handling
tools/kvm_stat: print error on invalid regex
tools/kvm_stat: fix crash when filtering out all non-child trace events
tools/kvm_stat: avoid 'is' for equality checks
tools/kvm_stat: use a more pythonic way to iterate over dictionaries
...
|
|
PMIC node requires external interrupts for proper operation, but property
defining them was missing. This was probably caused by a limited support
for interrupts from more than one parent, which was not possible to define
when support for this board was added. Fix this by adding
'interrupt-extended' property and properly define interrupt lines for PMIC
node.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Fix the unit addresses of PDMA nodes in Exynos5410 (the reg property is
correct) to get rid of DTC warnings like:
arch/arm/boot/dts/exynos5410-odroidxu.dtb: Warning (simple_bus_reg):
Node /soc/amba/pdma@12680000 simple-bus unit address format error, expected "121a0000"
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
Typo in unit address of PPMU ACP caused DTC warnings:
arch/arm/boot/dts/exynos4412-odroidu3.dtb:
Warning (simple_bus_reg): Node /soc/ppmu_acp@10ae0000 simple-bus unit address format error, expected "106e0000"
PPMU ACP (under 0x10ae0000 address) is present only in Exynos4210 so
move this node to exynos4210.dtsi with fixing the reg address to proper
one.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
When blkdev_open() races with device removal and creation it can happen
that unhashed bdev inode gets associated with newly created gendisk
like:
CPU0 CPU1
blkdev_open()
bdev = bd_acquire()
del_gendisk()
bdev_unhash_inode(bdev);
remove device
create new device with the same number
__blkdev_get()
disk = get_gendisk()
- gets reference to gendisk of the new device
Now another blkdev_open() will not find original 'bdev' as it got
unhashed, create a new one and associate it with the same 'disk' at
which point problems start as we have two independent page caches for
one device.
Fix the problem by verifying that the bdev inode didn't get unhashed
before we acquired gendisk reference. That way we make sure gendisk can
get associated only with visible bdev inodes.
Tested-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When two blkdev_open() calls for a partition race with device removal
and recreation, we can hit BUG_ON(!bd_may_claim(bdev, whole, holder)) in
blkdev_open(). The race can happen as follows:
CPU0 CPU1 CPU2
del_gendisk()
bdev_unhash_inode(part1);
blkdev_open(part1, O_EXCL) blkdev_open(part1, O_EXCL)
bdev = bd_acquire() bdev = bd_acquire()
blkdev_get(bdev)
bd_start_claiming(bdev)
- finds old inode 'whole'
bd_prepare_to_claim() -> 0
bdev_unhash_inode(whole);
<device removed>
<new device under same
number created>
blkdev_get(bdev);
bd_start_claiming(bdev)
- finds new inode 'whole'
bd_prepare_to_claim()
- this also succeeds as we have
different 'whole' here...
- bad things happen now as we
have two exclusive openers of
the same bdev
The problem here is that block device opens can see various intermediate
states while gendisk is shutting down and then being recreated.
We fix the problem by introducing new lookup_sem in gendisk that
synchronizes gendisk deletion with get_gendisk() and furthermore by
making sure that get_gendisk() does not return gendisk that is being (or
has been) deleted. This makes sure that once we ever manage to look up
newly created bdev inode, we are also guaranteed that following
get_gendisk() will either return failure (and we fail open) or it
returns gendisk for the new device and following bdget_disk() will
return new bdev inode (i.e., blkdev_open() follows the path as if it is
completely run after new device is created).
Reported-and-analyzed-by: Hou Tao <houtao1@huawei.com>
Tested-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When two blkdev_open() calls race with device removal and recreation,
__blkdev_get() can use looked up gendisk after it is freed:
CPU0 CPU1 CPU2
del_gendisk(disk);
bdev_unhash_inode(inode);
blkdev_open() blkdev_open()
bdev = bd_acquire(inode);
- creates and returns new inode
bdev = bd_acquire(inode);
- returns the same inode
__blkdev_get(devt) __blkdev_get(devt)
disk = get_gendisk(devt);
- got structure of device going away
<finish device removal>
<new device gets
created under the same
device number>
disk = get_gendisk(devt);
- got new device structure
if (!bdev->bd_openers) {
does the first open
}
if (!bdev->bd_openers)
- false
} else {
put_disk_and_module(disk)
- remember this was old device - this was last ref and disk is
now freed
}
disk_unblock_events(disk); -> oops
Fix the problem by making sure we drop reference to disk in
__blkdev_get() only after we are really done with it.
Reported-by: Hou Tao <houtao1@huawei.com>
Tested-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a proper counterpart to get_disk_and_module() -
put_disk_and_module(). Currently it is opencoded in several places.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Rename get_disk() to get_disk_and_module() to make sure what the
function does. It's not a great name but at least it is now clear that
put_disk() is not it's counterpart.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 8ddcd653257c "block: introduce GENHD_FL_HIDDEN" added handling of
hidden devices to get_gendisk() but forgot to drop module reference
which is also acquired by get_disk(). Drop the reference as necessary.
Arguably the function naming here is misleading as put_disk() is *not*
the counterpart of get_disk() but let's fix that in the follow up
commit since that will be more intrusive.
Fixes: 8ddcd653257c18a669fcb75ee42c37054908e0d6
CC: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Introduce __smp_{mb,rmb,wmb}, and rely on the generic definitions
for smp_{mb,rmb,wmb}. A first consequence is that smp_{mb,rmb,wmb}
map to a compiler barrier on !SMP (while their definition remains
unchanged on SMP). As a further consequence, smp_load_acquire and
smp_store_release have "fence rw,rw" instead of "fence iorw,iorw".
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
We don't want a separate module for vb2-trace.
That fixes this warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/media/common/videobuf2/vb2-trace.o
When building as module.
While here, add a SPDX header.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Currently if map is null then a potential null pointer deference
occurs when calling sock_release on map->sock. I believe the
actual intention was to call sock_release on sock instead. Fix
this.
Fixes: 5db4d286a8ef ("xen/pvcalls: implement connect command")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Commit e864f39569f4 "fs: add RWF_DSYNC aand RWF_SYNC" added additional
way for direct IO to become synchronous and thus trigger fsync from the
IO completion handler. Then commit 9830f4be159b "fs: Use RWF_* flags for
AIO operations" allowed these flags to be set for AIO as well. However
that commit forgot to update the condition checking whether the IO
completion handling should be defered to a workqueue and thus AIO DIO
with RWF_[D]SYNC set will call fsync() from IRQ context resulting in
sleep in atomic.
Fix the problem by checking directly iocb flags (the same way as it is
done in dio_complete()) instead of checking all conditions that could
lead to IO being synchronous.
CC: Christoph Hellwig <hch@lst.de>
CC: Goldwyn Rodrigues <rgoldwyn@suse.com>
CC: stable@vger.kernel.org
Reported-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Fixes: 9830f4be159b29399d107bffb99e0132bc5aedd4
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add support of stm32mp157c evaluation board (part number: STM32MP157C-EV1)
split in 2 elements:
-Daughter board (part number: STM32MP157C-ED1)
which includes CPU, memory and power supply
-Mother board (part number: STM32MP157C-EM1)
which includes external peripherals (like display, camera,...)
and extension connectors.
The daughter board can run alone, this is why the device tree files
are split in two layers, for the complete evaluation board (ev1)
and for the daughter board alone (ed1).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
