| Age | Commit message (Collapse) | Author |
|---|
|
Panel Power sequences for CNP is similar to Broxton,
but with only one sequencer.
Main difference from SPT is that PP_DIVISOR was removed
and power cycle delay has been moved to PP_CONTROL.
v2: Add missed pp_div write, that is now part of PP_CONTROL[8:4]
as on Broxton. (Found by DK)
v3: Improve commit message. (By DK)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Clinton Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-6-git-send-email-rodrigo.vivi@intel.com
|
|
On CNP PCH based platforms the gmbus is on the south display that
is on PCH. The existing implementation for previous platforms
already covers the need for CNP expect for the pin pair configuration
that follows similar definitions that we had on BXT.
v2: Don't drop "_BXT" as the indicator of the first platform
supporting this pin numbers. Suggested by Daniel.
v3: Add missing else and fix register table since CNP GPIO_CTL
starts on 0xC5014.
v4: Fix pin number and map according to the current available VBT.
Re-add pin 4 for port D. Lost during some rebase.
v5: Use table as spec. If VBT is wrong it should be ignored.
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-5-git-send-email-rodrigo.vivi@intel.com
|
|
Split out BXT and CNP's setup_backlight(),enable_backlight(),
disable_backlight() and hz_to_pwm() into
two separate functions instead of reusing BXT function.
Reuse set_backlight() and get_backlight() since they have
no reference to the utility pin.
v2: Reuse BXT functions with controller 0 instead of
redefining it. (Jani).
Use dev_priv->rawclk_freq instead of getting the value
from SFUSE_STRAP.
v3: Avoid setup backligh controller along with hooks and
fully reuse hooks setup as suggested by Jani.
v4: Clean up commit message.
v5: Implement per PCH instead per platform.
v6: Introduce a new function for CNP.(Jani and Ville)
v7: Squash the all CNP Backlight support patches into a
single patch. (Jani)
v8: Correct indentation, remove unneeded blank lines and
correct mail address (Jani).
v9: Remove unused enum pipe. (by CI)
v10: Remove comment mentioning SFUSE_STRAP in a part of
the code that we don't use it. (Jani)
Make controller = 0 since current CNP has only one
controller and put a comment mentioning why we
reuse the BXT definitions and are keeping the
controller = 0. (DK)
v11: Remove spurious line. (DK)
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Suggested-by: Ville Syrjala <ville.syrjala@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-4-git-send-email-rodrigo.vivi@intel.com
|
|
RAWCLK_FREQ register has changed for platforms with CNP+.
[29:26] This field provides the denominator for the fractional
part of the microsecond counter divider. The numerator
is fixed at 1. Program this field to the denominator of
the fractional portion of reference frequency minus one.
If the fraction is 0, program to 0.
0100b = Fraction .2 MHz = Fraction 1/5.
0000b = Fraction .0 MHz.
[25:16] This field provides the integer part of the microsecond
counter divider. Program this field to the integer portion
of the reference frequenct minus one.
Also this register tells us that proper raw clock should be read
from SFUSE_STRAP and programmed to this register. Up to this point
on other platforms we are reading instead of programming it so
probably relying on whatever BIOS had configured here.
Now on let's follow the spec and also program this register
fetching the right value from SFUSE_STRAP as Spec tells us to do.
v2: Read from SFUSE_STRAP and Program RAWCLK_FREQ instead of
reading the value relying someone else will program that
for us.
v3: Add missing else. (Jani)
v4: Addressing all Ville's catches:
Use macro for shift bits instead of defining shift.
Remove shift from the cleaning bits with mask that already
has it.
Add missing I915_WRITE to actually write the reg.
Stop using useless DIV_ROUND_* on divider that is exact
dividion and use DIV_ROUND_CLOSEST for the fraction part.
v5: Remove useless Read-Modify-Write on raclk_freq reg. (Ville).
v6: Change is per PCH instead of per platform.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-3-git-send-email-rodrigo.vivi@intel.com
|
|
The first two bytes of PCI ID for CNP_LP PCH are the same as that of
SPT_LP. We should really be looking at the first 9 bits instead of the
first 8 to identify platforms, although this seems to have not caused any
problems on earlier platforms. Introduce a 9 bit extended mask for SPT and
CNP while not touching the code for any of the other platforms.
v2: (Rodrigo) Make platform agnostic and fix commit message.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-2-git-send-email-rodrigo.vivi@intel.com
|
|
Most of south engine display that is in PCH is still the
same as SPT and KBP, except for this key differences:
- Backlight: Backlight programming changed in CNP PCH.
- Panel Power: Sligh programming changed in CNP PCH.
- GMBUS and GPIO: The pin mapping has changed in CNP PCH.
All of these changes follow more the BXT style.
v2: Update definition to use dev_priv isntead of dev (Tvrtko).
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-1-git-send-email-rodrigo.vivi@intel.com
|
|
Failing to do so meant that we got a resume() callback on first use of
the device, so we would leak the bin BO that we allocated during
probe.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 553c942f8b2c ("drm/vc4: Allow using more than 256MB of CMA memory.")
Link: http://patchwork.freedesktop.org/patch/msgid/20170515171615.10168-1-eric@anholt.net
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Pull XFS fix from Darrick Wong:
"I've one more bugfix for you for 4.12-rc4: Fix an unmount hang due to
a race in io buffer accounting"
* tag 'xfs-4.12-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: use ->b_state to fix buffer I/O accounting release race
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"ACPI-related fixes for arm64:
- GICC MADT entry validity check fix
- Skip IRQ registration with pmu=off in an ACPI guest
- struct acpi_pci_root_ops freeing on error path"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
ARM64/ACPI: Fix BAD_MADT_GICC_ENTRY() macro implementation
drivers/perf: arm_pmu_acpi: avoid perf IRQ init when guest PMU is off
ARM64: PCI: Fix struct acpi_pci_root_ops allocation failure path
|
|
Pull ceph fix from Ilya Dryomov:
"A small fix for rbd FALLOC_FL_ZERO_RANGE/PUNCH_HOLE handling breakage
introduced in -rc1"
* tag 'ceph-for-4.12-rc4' of git://github.com/ceph/ceph-client:
rbd: implement REQ_OP_WRITE_ZEROES
|
|
If logout response is not received and ->ep_disconnect() is called then
close tcp conn by RST instead of FIN to cleanup conn resources
immediately.
Also move ->csk_push_tx_frames() above 'done:' to avoid calling
->csk_push_tx_frames() in error cases.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a DM verity fix for a mode when no salt is used
- a fix to DM to account for the possibility that PREFLUSH or FUA are
used without the SYNC flag if the underlying storage doesn't have a
volatile write-cache
- a DM ioctl memory allocation flag fix to use __GFP_HIGH to allow
emergency forward progress (by using memory reserves as last resort)
- a small DM integrity cleanup to use kvmalloc() instead of duplicating
the same
* tag 'for-4.12/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: make flush bios explicitly sync
dm ioctl: restore __GFP_HIGH in copy_params()
dm integrity: use kvmalloc() instead of dm_integrity_kvmalloc()
dm verity: fix no salt use case
|
|
Pull MD fixes from Shaohua Li:
"Several patches for MD. One notable is making flush bios sync, others
fix small issues"
* tag 'md/4.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md: Make flush bios explicitely sync
md: report sector of stripes with check mismatches
md: uuid debug statement now in processor byte order.
md-cluster: fix potential lock issue in add_new_disk
|
|
Pull block fixes from Jens Axboe:
"A set of fixes that should go into the next -rc. This contains:
- A use-after-free in the request_list exit for the legacy IO path,
from Bart.
- A fix for CFQ, fixing a recent regression with the conversion to
higher resolution timing for iops mode. From Hou Tao.
- A single fix for nbd, split in two patches, fixing a leak of a data
structure.
- A regression fix from Keith, ensuring that callers of
blk_mq_update_nr_hw_queues() hold the right lock"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Avoid that blk_exit_rl() triggers a use-after-free
cfq-iosched: fix the delay of cfq_group's vdisktime under iops mode
blk-mq: Take tagset lock when updating hw queues
nbd: don't leak nbd_config
nbd: nbd_reset() call in nbd_dev_add() is redundant
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm displayport quirk support:
"DP quirk for usb c dongles.
As mentioned I have a separate request for fixing a regression, but
also keeping the broken hw working, for certain USB-C DP adapters they
require a minimised n/m parameters, but an attempt to do this
generically has failed, we need to quirk these specific adapters.
However doing it generically regressed some eDP panels.
This pull adds the infrastructure and a quirk for the adapter"
* tag 'drm-dp-quirk-for-v4.12-rc4' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Detect USB-C specific dongles before reducing M and N
drm/dp: start a DPCD based DP sink/branch device quirk database
drm/i915: use drm DP helper to read DPCD desc
drm/dp: add helper for reading DP sink/branch device desc from DPCD
|
|
commit d85b758f72b0 ("virtio_net: fix support for small rings")
was supposed to increase the buffer size for small rings but had an
unintentional side effect of decreasing it for large rings. This seems
to break some setups - it's not yet clear why, but increasing buffer
size back to what it was before helps.
Fixes: d85b758f72b0 ("virtio_net: fix support for small rings")
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Qlogic's 82xx series adapter doesn't support
tunnel offloads, driver incorrectly assumes that it is
supported and causes firmware hang while running tunnel IO.
This patch fixes this by not advertising tunnel offloads
for 82xx adapters.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding a vxlan interface to a socket isn't symmetrical, while adding
is done in vxlan_open() the deletion is done in vxlan_dellink().
This can cause a use-after-free error when we close the vxlan
interface before deleting it.
We add vxlan_vs_del_dev() to match vxlan_vs_add_dev() and call
it from vxlan_stop() to match the call from vxlan_open().
Fixes: 56ef9c909b40 ("vxlan: Move socket initialization to within rtnl scope")
Acked-by: Jiri Benc <jbenc@redhat.com>
Tested-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original author left the project and so far has not
responded to emails sent to the listed address.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix NETDEV WATCHDOG timeout on startup by adding missing register
writes that properly setup SGMII.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the sender switches its congestion control during loss
recovery, if the recovery is spurious then it may incorrectly
revert cwnd and ssthresh to the older values set by a previous
congestion control. Consider a congestion control (like BBR)
that does not use ssthresh and keeps it infinite: the connection
may incorrectly revert cwnd to an infinite value when switching
from BBR to another congestion control.
This patch fixes it by disallowing such cwnd undo operation
upon switching congestion control. Note that undo_marker
is not reset s.t. the packets that were incorrectly marked
lost would be corrected. We only avoid undoing the cwnd in
tcp_undo_cwnd_reduction().
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Take uld mutex to avoid race between cxgb_up() and
cxgb4_register_uld() to enable napi for the same uld
queue.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xfrm6_find_1stfragopt() may now return an error code and we must
not treat it as a length.
Fixes: 2423496af35d ("ipv6: Prevent overrun when parsing v6 header options")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains the fixes for a few reported regression for HD-audio and
USB-audio. All small, trivial, and boring"
* tag 'sound-4.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix applying MSI dual-codec mobo quirk
ALSA: usb: Avoid VLA in mixer_us16x08.c
ALSA: usb: Fix a typo in Tascam US-16x08 mixer element
Revert "ALSA: usb-audio: purge needless variable length array"
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Here is the dmaengine fixes request for 4.12. Fixes bunch of issues in
the driver, npthing exciting though..
- mv_xor_v2 driver fixes for handling descriptors, tx_submit
implementation, removing interrupt coalescing and setting DMA mask
properly
- fix usb-dmac DMAOR AE bit definition
- fix ep93xx start buffer from BASE0 and not drain the transfers in
terminate_all
- fix rcar-dmac to use right descriptor pointer for residue
calculation
- pl330 fix warn for irq freeup"
* tag 'dmaengine-fix-4.12-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: pl330: fix warning in pl330_remove
rcar-dmac: fixup descriptor pointer for descriptor mode
dmaengine: ep93xx: Don't drain the transfers in terminate_all()
dmaengine: ep93xx: Always start from BASE0
dmaengine: usb-dmac: Fix DMAOR AE bit definition
dmaengine: mv_xor_v2: set DMA mask to 40 bits
dmaengine: mv_xor_v2: remove interrupt coalescing
dmaengine: mv_xor_v2: fix tx_submit() implementation
dmaengine: mv_xor_v2: enable XOR engine after its configuration
dmaengine: mv_xor_v2: do not use descriptors not acked by async_tx
dmaengine: mv_xor_v2: properly handle wrapping in the array of HW descriptors
dmaengine: mv_xor_v2: handle mv_xor_v2_prep_sw_desc() error properly
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- corner-case oops fixes for Asus and Wacom drivers from Carlo Caione
and Jason Gerecke
- power management fix (reported on SIS0817 touchscreen) for i2c-hid
devices from Hans de Goede
- device-id-specific fixes and quirks from Hans de Goede, Diego Elio
Pettenò and Che-Liang Chiou
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: asus: Stop underlying hardware on remove
HID: i2c: Call acpi_device_fix_up_power for ACPI-enumerated devices
HID: asus: Add support for T100 keyboard
HID: elecom: extend to fix the descriptor for DEFT trackballs
HID: magicmouse: Set multi-touch keybits for Magic Mouse
HID: wacom: Have wacom_tpc_irq guard against possible NULL dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching
Pull livepatching fix from Jiri Kosina:
"Kconfig dependency fix for livepatching infrastructure from Miroslav
Benes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: Make livepatch dependent on !TRIM_UNUSED_KSYMS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- revert a broken PAT commit that broke a number of systems
- fix two preemptability warnings/bugs that can trigger under certain
circumstances, in the debug code and in the microcode loader"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "x86/PAT: Fix Xorg regression on CPUs that don't support PAT"
x86/debug/32: Convert a smp_processor_id() call to raw to avoid DEBUG_PREEMPT warning
x86/microcode/AMD: Change load_microcode_amd()'s param to bool to fix preemptibility bug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Misc fixes:
- three boot crash fixes for uncommon configurations
- silence a boot warning under virtualization
- plus a GCC 7 related (harmless) build warning fix"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/bgrt: Skip efi_bgrt_init() in case of non-EFI boot
x86/efi: Correct EFI identity mapping under 'efi=old_map' when KASLR is enabled
x86/efi: Disable runtime services on kexec kernel if booted with efi=old_map
efi: Remove duplicate 'const' specifiers
efi: Don't issue error message when booted under Xen
|
|
commit a39be606f99d ("drm: Do a full device unregister when unplugging")
causes backtraces like this one when unplugging an usb drm device while
it is in use:
usb 2-3: USB disconnect, device number 25
------------[ cut here ]------------
WARNING: CPU: 0 PID: 242 at drivers/gpu/drm/drm_mode_config.c:424
drm_mode_config_cleanup+0x220/0x280 [drm]
...
RIP: 0010:drm_mode_config_cleanup+0x220/0x280 [drm]
...
Call Trace:
gm12u320_modeset_cleanup+0xe/0x10 [gm12u320]
gm12u320_driver_unload+0x35/0x70 [gm12u320]
drm_dev_unregister+0x3c/0xe0 [drm]
drm_unplug_dev+0x12/0x60 [drm]
gm12u320_usb_disconnect+0x36/0x40 [gm12u320]
usb_unbind_interface+0x72/0x280
device_release_driver_internal+0x158/0x210
device_release_driver+0x12/0x20
bus_remove_device+0x104/0x180
device_del+0x1d2/0x350
usb_disable_device+0x9f/0x270
usb_disconnect+0xc6/0x260
...
[drm:drm_mode_config_cleanup [drm]] *ERROR* connector Unknown-1 leaked!
------------[ cut here ]------------
WARNING: CPU: 0 PID: 242 at drivers/gpu/drm/drm_mode_config.c:458
drm_mode_config_cleanup+0x268/0x280 [drm]
...
<same Call Trace>
---[ end trace 80df975dae439ed6 ]---
general protection fault: 0000 [#1] SMP
...
Call Trace:
? __switch_to+0x225/0x450
drm_mode_rmfb_work_fn+0x55/0x70 [drm]
process_one_work+0x193/0x3c0
worker_thread+0x4a/0x3a0
...
RIP: drm_framebuffer_remove+0x62/0x3f0 [drm] RSP: ffffb776c39dfd98
---[ end trace 80df975dae439ed7 ]---
After which the system is unusable this is caused by drm_dev_unregister
getting called immediately on unplug, which calls the drivers unload
function which calls drm_mode_config_cleanup which removes the framebuffer
object while userspace is still holding a reference to it.
Reverting commit a39be606f99d ("drm: Do a full device unregister
when unplugging") leads to the following oops on unplug instead,
when userspace closes the last fd referencing the drm_dev:
sysfs group 'power' not found for kobject 'card1-Unknown-1'
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2459 at fs/sysfs/group.c:237
sysfs_remove_group+0x80/0x90
...
RIP: 0010:sysfs_remove_group+0x80/0x90
...
Call Trace:
dpm_sysfs_remove+0x57/0x60
device_del+0xfd/0x350
device_unregister+0x1a/0x60
drm_sysfs_connector_remove+0x39/0x50 [drm]
drm_connector_unregister+0x5a/0x70 [drm]
drm_connector_unregister_all+0x45/0xa0 [drm]
drm_modeset_unregister_all+0x12/0x30 [drm]
drm_dev_unregister+0xca/0xe0 [drm]
drm_put_dev+0x32/0x60 [drm]
drm_release+0x2f3/0x380 [drm]
__fput+0xdf/0x1e0
...
---[ end trace ecfb91ac85688bbe ]---
BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8
IP: down_write+0x1f/0x40
...
Call Trace:
debugfs_remove_recursive+0x55/0x1b0
drm_debugfs_connector_remove+0x21/0x40 [drm]
drm_connector_unregister+0x62/0x70 [drm]
drm_connector_unregister_all+0x45/0xa0 [drm]
drm_modeset_unregister_all+0x12/0x30 [drm]
drm_dev_unregister+0xca/0xe0 [drm]
drm_put_dev+0x32/0x60 [drm]
drm_release+0x2f3/0x380 [drm]
__fput+0xdf/0x1e0
...
---[ end trace ecfb91ac85688bbf ]---
This is caused by the revert moving back to drm_unplug_dev calling
drm_minor_unregister which does:
device_del(minor->kdev);
dev_set_drvdata(minor->kdev, NULL); /* safety belt */
drm_debugfs_cleanup(minor);
Causing the sysfs entries to already be removed even though we still
have references to them in e.g. drm_connector.
Note we must call drm_minor_unregister to notify userspace of the unplug
of the device, so calling drm_dev_unregister is not completely wrong the
problem is that drm_dev_unregister does too much.
This commit fixes drm_unplug_dev by not only reverting
commit a39be606f99d ("drm: Do a full device unregister when unplugging")
but by also adding a call to drm_modeset_unregister_all before the
drm_minor_unregister calls to make sure all sysfs entries are removed
before calling device_del(minor->kdev) thereby also fixing the second
set of oopses caused by just reverting the commit.
Fixes: a39be606f99d ("drm: Do a full device unregister when unplugging")
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jeffy <jeffy.chen@rock-chips.com>
Cc: Marco Diego Aurélio Mesquita <marcodiegomesquita@gmail.com>
Reported-by: Marco Diego Aurélio Mesquita <marcodiegomesquita@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601115430.4113-1-hdegoede@redhat.com
|
|
Instead of rewriting write/readq, use linux/io-64-nonatomic-lo-hi.h which
already have them.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170602112510.17544-1-clabbe.montjoie@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two fixes:
* fix the per-CPU drop counters to not be added to the
rx_packets counter, but really the drop counter
* fix TX aggregation start/stop callback races by setting
bits instead of allocating and queueing an skb
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dsa_switch_suspend() and dsa_switch_resume() are functions that belong in
net/dsa/dsa.c and are not part of the legacy platform support code.
Fixes: a6a71f19fe5e ("net: dsa: isolate legacy code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On SYSTEMPORT Lite, since we have the main interrupt source in the first
cell, the second cell is the Wake-on-LAN interrupt, yet the code was not
properly updated to fetch the second cell, and instead looked at the
third and non-existing cell for Wake-on-LAN.
Fixes: 44a4524c54af ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only print the NMI watchdog hint when that watchdog it actually enabled.
This avoids printing these unnecessarily.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/n/tip-lnw7edxnqsphkmeew857wz1i@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The BAD_MADT_GICC_ENTRY() macro checks if a GICC MADT entry passes
muster from an ACPI specification standpoint. Current macro detects the
MADT GICC entry length through ACPI firmware version (it changed from 76
to 80 bytes in the transition from ACPI 5.1 to ACPI 6.0 specification)
but always uses (erroneously) the ACPICA (latest) struct (ie struct
acpi_madt_generic_interrupt - that is 80-bytes long) length to check if
the current GICC entry memory record exceeds the MADT table end in
memory as defined by the MADT table header itself, which may result in
false negatives depending on the ACPI firmware version and how the MADT
entries are laid out in memory (ie on ACPI 5.1 firmware MADT GICC
entries are 76 bytes long, so by adding 80 to a GICC entry start address
in memory the resulting address may well be past the actual MADT end,
triggering a false negative).
Fix the BAD_MADT_GICC_ENTRY() macro by reshuffling the condition checks
and update them to always use the firmware version specific MADT GICC
entry length in order to carry out boundary checks.
Fixes: b6cfb277378e ("ACPI / ARM64: add BAD_MADT_GICC_ENTRY() macro")
Reported-by: Julien Grall <julien.grall@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Julien Grall <julien.grall@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Al Stone <ahs3@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In commit 5763ff04dc4e ("drm/i915: Avoid GPU stalls from kswapd") we
stopped direct reclaim and kswapd from triggering GPU/client stalls
whilst running (by restricting the objects they could reap to be idle).
However with abusive GPU usage, it becomes quite easy to starve kswapd
of memory and prevent it from making forward progress towards obtaining
enough free memory (thus driving the system closer to swap exhaustion).
Relax the previous restriction to allow kswapd (but not direct reclaim)
to stall the device whilst reaping purgeable pages.
v2: Also acquire the rpm wakelock to allow kswapd to unbind buffers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601133331.5973-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
I915_GEM_GET_APERTURE ioctl is used to probe aperture size from userspace.
In gvt environment, each vm only use the ballooned part of aperture, so we
should return the correct available aperture size exclude the reserved part
by balloon.
v2: add 'reserved' in struct i915_address_space to record the reserved size
in ggtt (Chris)
v3: remain aper_size as total, adjust aper_available_size exclude reserved
and pinned. UMD driver need to adjust the max allocation size according to
the available aperture size but not total size. KMD return the correct
usable aperture size any time (Chris, Joonas)
v4: decrease reserved in deballoon (Joonas)
v5: add onion teardown in balloon, add vgt_deballoon_space (Joonas)
v6: change title name (Zhenyu)
v7: code style refine (Joonas)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496198152-14175-1-git-send-email-weinan.z.li@intel.com
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
We are missing a call to hid_hw_stop() on the remove hook.
Among other things this is causing an Oops when (re-)starting GNOME /
upowerd / ... after the module has been already rmmod-ed.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The PN_INT_ENA register should be used after usb3_pn_change() is called.
So, this patch moves the access from renesas_usb3_stop_controller() to
usb3_disable_pipe_n().
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This controller disallows to change the PIPE until reading/writing
a packet finishes. However. the previous code is not enough to hold
the lock in some functions. So, this patch fixes it.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that this driver is possible to cause
deadlock by double-spinclocked in renesas_usb3_stop_controller().
So, this patch removes spinlock API calling in renesas_usb3_stop().
(In other words, the previous code had a redundant lock.)
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that this driver is possible to access
the registers before pm_runtime_get_sync() if a gadget driver is
installed first. After that, oops happens on R-Car Gen3 environment.
To avoid it, this patch changes the pm_runtime call timing from
probe/remove to udc_start/udc_stop.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
f_mass_storage has a memorry barrier issue with the sleep and wake
functions that can cause a deadlock. This results in intermittent hangs
during MSC file transfer. The host will reset the device after receiving
no response to resume the transfer. This issue is seen when dwc3 is
processing 2 transfer-in-progress events at the same time, invoking
completion handlers for CSW and CBW. Also this issue occurs depending on
the system timing and latency.
To increase the chance to hit this issue, you can force dwc3 driver to
wait and process those 2 events at once by adding a small delay (~100us)
in dwc3_check_event_buf() whenever the request is for CSW and read the
event count again. Avoid debugging with printk and ftrace as extra
delays and memory barrier will mask this issue.
Scenario which can lead to failure:
-----------------------------------
1) The main thread sleeps and waits for the next command in
get_next_command().
2) bulk_in_complete() wakes up main thread for CSW.
3) bulk_out_complete() tries to wake up the running main thread for CBW.
4) thread_wakeup_needed is not loaded with correct value in
sleep_thread().
5) Main thread goes to sleep again.
The pattern is shown below. Note the 2 critical variables.
* common->thread_wakeup_needed
* bh->state
CPU 0 (sleep_thread) CPU 1 (wakeup_thread)
============================== ===============================
bh->state = BH_STATE_FULL;
smp_wmb();
thread_wakeup_needed = 0; thread_wakeup_needed = 1;
smp_rmb();
if (bh->state != BH_STATE_FULL)
sleep again ...
As pointed out by Alan Stern, this is an R-pattern issue. The issue can
be seen when there are two wakeups in quick succession. The
thread_wakeup_needed can be overwritten in sleep_thread, and the read of
the bh->state maybe reordered before the write to thread_wakeup_needed.
This patch applies full memory barrier smp_mb() in both sleep_thread()
and wakeup_thread() to ensure the order which the thread_wakeup_needed
and bh->state are written and loaded.
However, a better solution in the future would be to use wait_queue
method that takes care of managing memory barrier between waker and
waiter.
Cc: <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that we have a callback to check if crtc supports a given mode
we can use it in atmel-hlcdc so that we restrict the number of probbed
modes to the ones we can actually display.
Also, remove the mode_fixup() callback as this is no longer needed
because mode_valid() will be called before.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/95fd6c06c58bd0b957e36a8d7068e6a74b581304.1495720737.git.joabreu@synopsys.com
|
|
USB support in the Meson8 SoCs is provided by a DWC2 controller which
works with the same settings as Meson8b and GXBB. Using the generic
"snps,dwc2" binding results in an endless stream of "Overcurrent change
detected" messages.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
omap_gem uses page alignment for buffer stride. The related calculations
are a bit off, though, as byte stride of 4096 gets aligned to 8192,
instead of 4096.
This patch changes the code to use DIV_ROUND_UP(), which fixes those
calculations and makes them more readable.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
When rotating 90/270 + mirroring with YUV422, the end result will have
adjacent pixels swapped. The problem is that
dispc_ovl_set_rotation_attrs() has wrong rotation values for these
cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
TILER rotation with YUV422 pixelformats does not work at the moment. All
other pixel formats work, because the pixelformat's pixel size is equal
to tiler unit size (e.g. XR24's pixel size is 32 bits, and the TILER
unit size that has to be used is 32 bits).
For YUV422 formats this is not the case, as the TILER unit size has to
be 32 bits, but the pixel size is 16 bits. The end result is OCP errors
and sync losts.
This patch adds the code to adjust the variables for YUV422 formats.
We could make the code more generic by passing around the pixel format,
rotation type, angle and the tiler unit size, which would allow us to do
calculations without special case for YUV422. However, this would make
the code more complex, and at least for now this is much more easier to
handle with these two special cases for YUV422.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The omapdrm driver has not passed the rotation value to the dispc
driver. This doesn't affect RGB formats, but YUV formats don't work
without dispc knowing the orientation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
