| Age | Commit message (Collapse) | Author |
|---|
|
imx6qdl-gw5x boards use sgtl5000 codec and the machine file (imx-sgtl5000)
already sets SSI in slave mode and codec in master mode, so there is no need
for having this property.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Use IMX6QDL_CLK_CKO definition instead of its hard coded clock number for better
readability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fix from Ingo Molnar:
"Fix GENMASK macro shift overflow"
Nobody seems to currently use GENMASK() to fill every single last bit
(which is what overflows) in-tree, and gcc would warn about it, so we
have that going for us. But apparently there are pending changes that
want this.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
bitops: Fix shift overflow in GENMASK macros
|
|
This adds the NovaTech OrionLXm which is based on the AM335x SoC
http://www.novatechweb.com/substation-automation/orionlxm/
RAM: 512MiB
Flash: 4GB eMMC
Ethernet PHYs: 2x Micrel KSZ8041FTLI
USB ports are used internally by the expansion cards.
Internal micro SD slot is available.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.19/soc
Several more OMAP patches targeted for v3.19. They include:
- OMAP4/5: DSS hwmod cleanup patches from Tomi Valkeinen.
- DRA7xx: hwmod data support for UARTs 7 through 10.
- AM43xx: hwmod data support for the onboard ADC.
Basic build, boot, and PM test reports are here:
http://www.pwsan.com/omap/testlogs/omap-b-for-v3.19/20141121110550/
Note that I cannot test the DRA7xx or AM43xx patches, since I do not have
these boards.
|
|
Commit c3ae62af8e755 ("tcp: should drop incoming frames without ACK
flag set") was created to mitigate a security vulnerability in which a
local attacker is able to inject data into locally-opened sockets by
using TCP protocol statistics in procfs to quickly find the correct
sequence number.
This broke the RFC5961 requirement to send a challenge ACK in response
to spurious RST packets, which was subsequently fixed by commit
7b514a886ba50 ("tcp: accept RST without ACK flag").
Unfortunately, the RFC5961 requirement that spurious SYN packets be
handled in a similar manner remains broken.
RFC5961 section 4 states that:
... the handling of the SYN in the synchronized state SHOULD be
performed as follows:
1) If the SYN bit is set, irrespective of the sequence number, TCP
MUST send an ACK (also referred to as challenge ACK) to the remote
peer:
<SEQ=SND.NXT><ACK=RCV.NXT><CTL=ACK>
After sending the acknowledgment, TCP MUST drop the unacceptable
segment and stop processing further.
By sending an ACK, the remote peer is challenged to confirm the loss
of the previous connection and the request to start a new connection.
A legitimate peer, after restart, would not have a TCB in the
synchronized state. Thus, when the ACK arrives, the peer should send
a RST segment back with the sequence number derived from the ACK
field that caused the RST.
This RST will confirm that the remote peer has indeed closed the
previous connection. Upon receipt of a valid RST, the local TCP
endpoint MUST terminate its connection. The local TCP endpoint
should then rely on SYN retransmission from the remote end to
re-establish the connection.
This patch lets SYN packets through the discard added in c3ae62af8e755,
so that spurious SYN packets are properly dealt with as per the RFC.
The challenge ACK is sent unconditionally and is rate-limited, so the
original vulnerability is not reintroduced by this patch.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not sure what I was thinking, but doing anything after
releasing a refcount is suicidal or/and embarrassing.
By the time we set skb->fclone to SKB_FCLONE_FREE, another cpu
could have released last reference and freed whole skb.
We potentially corrupt memory or trap if CONFIG_DEBUG_PAGEALLOC is set.
Reported-by: Chris Mason <clm@fb.com>
Fixes: ce1a4ea3f1258 ("net: avoid one atomic operation in skb_clone()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since all users have been converted to using the 64bit
timekeeping_inject_sleeptime64(), remove the old y2038
problematic timekeeping_inject_sleeptime().
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Currently the rtc suspend/resume timing is done using
y2038 problematic timespecs. So update the code to utilize
timespec64 types.
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
As part of addressing "y2038 problem" for in-kernel uses, this patch
adds safe rtc_tm_to_time64()/rtc_time64_to_tm() respectively using
time64_t.
After this patch, rtc_tm_to_time() is deprecated and all its call
sites will be fixed using corresponding safe versions, it can be
removed when having no users. Also change rtc_tm_to_time64() to
return time64_t directly instead of just as a parameter like
rtc_tm_to_time() does.
After this patch, rtc_time_to_tm() is deprecated and all its call
sites will be fixed using corresponding safe versions, it can be
removed when having no users.
In addition, change rtc_tm_to_ktime() and rtc_ktime_to_tm() to use
the safe version in passing.
Signed-off-by: pang.xunlei <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Fix up a few comments that weren't updated when the
functions were converted to use timespec64 structures.
Acked-by: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Adds a timespec64 based get_monotonic_coarse64() implementation
that can be used as we convert internal users of
get_monotonic_coarse away from using timespecs.
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Adds a timespec64 based getrawmonotonic64() implementation
that can be used as we convert internal users of
getrawmonotonic away from using timespecs.
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
As part of addressing "y2038 problem" for in-kernel uses, this
patch adds safe mktime64() using time64_t.
After this patch, mktime() is deprecated and all its call sites
will be fixed using mktime64(), after that it can be removed.
Signed-off-by: pang.xunlei <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
As part of addressing "y2038 problem" for in-kernel uses, this
patch adds timekeeping_inject_sleeptime64() using timespec64.
After this patch, timekeeping_inject_sleeptime() is deprecated
and all its call sites will be fixed using the new interface,
after that it can be removed.
NOTE: timekeeping_inject_sleeptime() is safe actually, but we
want to eliminate timespec eventually, so comes this patch.
Signed-off-by: pang.xunlei <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
The kernel uses 32-bit signed value(time_t) for seconds elapsed
1970-01-01:00:00:00, thus it will overflow at 2038-01-19 03:14:08
on 32-bit systems. This is widely known as the y2038 problem.
As part of addressing "y2038 problem" for in-kernel uses, this patch
adds safe do_settimeofday64() using timespec64.
After this patch, do_settimeofday() is deprecated and all its call
sites will be fixed using do_settimeofday64(), after that it can be
removed.
Signed-off-by: pang.xunlei <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
The clocksource mult-adjustment threshold is [mult-maxadj, mult+maxadj],
timekeeping_adjust() only deals with the upper threshold, but misses the
lower threshold.
This patch adds the lower threshold judging condition.
Signed-off-by: pang.xunlei <pang.xunlei@linaro.org>
[jstultz: Minor fix for > 80 char line]
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Ideally, __clocksource_updatefreq_scale, selects the largest shift
value possible for a clocksource. This results in the mult memember of
struct clocksource being particularly large, although not so large
that NTP would adjust the clock to cause it to overflow.
That said, nothing actually prohibits an overflow from occuring, its
just that it "shouldn't" occur.
So while very unlikely, and so far never observed, the value of
(cs->mult+cs->maxadj) may have a chance to reach very near 0xFFFFFFFF,
so there is a possibility it may overflow when doing NTP positive
adjustment
See the following detail: When NTP slewes the clock, kernel goes
through update_wall_time()->...->timekeeping_apply_adjustment():
tk->tkr.mult += mult_adj;
Since there is no guard against it, its possible tk->tkr.mult may
overflow during this operation.
This patch avoids any possible mult overflow by judging the overflow
case before adding mult_adj to mult, also adds the WARNING message
when capturing such case.
Signed-off-by: pang.xunlei <pang.xunlei@linaro.org>
[jstultz: Reworded commit message]
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Kees requested that this test module be renamed for consistency sake,
so this patch renames the udelay_test.c file (recently added to
tip/timers/core for 3.17) to test_udelay.c
Cc: Kees Cook <keescook@chromium.org>
Cc: Greg KH <greg@kroah.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Linux-Next <linux-next@vger.kernel.org>
Cc: David Riley <davidriley@chromium.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
The list of gpios is defined as optional but the code was
failing to properly handle the case of no gpios, and also
failing to check for errors reading the entry from the
devicetree.
This patch fixes the handling of optional gpios - this is a
useful feature enabling the gpio-regulator to be used as a
dummy variable voltage regulator without having to assign any
real GPIO lines.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The IPQ8064 reference boards make use of SMB208 regulators which are
controlled by RPM. Implement support for these regulators in the RPM
regulator driver.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The functions cpufreq_cooling_unregister() and thermal_zone_device_unregister()
test whether their argument is NULL and then return immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Prevents build warning:
st_thermal.c:278:12:
warning: ‘st_thermal_suspend’ defined but not used [-Wunused-function]
st_thermal.c:286:12:
warning: ‘st_thermal_resume’ defined but not used [-Wunused-function]
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Call platform_get_irq_byname() already returns VIRQ instead of local
IRQ. Passing this value to regmap_irq_get_virq() causes error which
results in IRQ registration failure. This patch fixes such behaviour.
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
The toggle bit shouldn't be cleared before the toggle value is calculated.
This should probably go into 3.17.x as well.
Fixes: 120703f9eb32 ([media] rc-core: document the protocol type)
Cc: stable@vger.kernel.org # For v3.17
Tested-by: Stephan Raue <mailinglists@openelec.tv>
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Simplify the pool_io_hints code that works to establish a max_sectors
value that is a power-of-2 factor of the thin-pool's blocksize. The
biggest associated improvement is that the DM thin-pool is no longer
concerning itself with the data device's max_hw_sectors when adjusting
max_sectors.
This fixes the relative fragility of the original "dm thin: adjust
max_sectors_kb based on thinp blocksize" commit that only became
apparent when testing was performed using a DM thin-pool ontop of a
virtio_blk device. One proposed upstream patch detailed the problems
inherent in virtio_blk: https://lkml.org/lkml/2014/11/20/611
So even though virtio_blk incorrectly set its max_hw_sectors it actually
helped make it clear that we need DM thinp to be tolerant of any future
Linux driver that incorrectly sets max_hw_sectors.
We only need to be concerned with modifying the thin-pool device's
max_sectors limit if it is smaller than the thin-pool's blocksize. In
this case the value of max_sectors does become a limiting factor when
upper layers (e.g. filesystems) construct their bios. But if the
hardware can support IOs larger than the thin-pool's blocksize the user
is encouraged to adjust the thin-pool's data device's max_sectors
accordingly -- doing so will enable the thin-pool to inherit the
established user-defined max_sectors.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
I'm using the new Open Source Group address for my upstream work.
While the other email is still valid, it is better for me to receive
patches via the new address.
So, replace it everywhere inside MAINTAINERS.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The cx23885 driver still used sg++ instead of sg = sg_next(sg). This worked with
vb1 since that filled in the sglist manually, page-by-page, but it fails with vb2
which uses core scatterlist code that can combine contiguous scatterlist entries
into one larger entry.
This bug led to the following crash as reported by Mariusz:
[20712.990258] BUG: Bad page state in process vb2-cx23885[0] pfn:2ca34
[20712.990265] page:ffffea00009c3b60 count:-1 mapcount:0 mapping: (null) index:0x0
[20712.990266] flags: 0x4000000000000000()
[20712.990268] page dumped because: nonzero _count
[20712.990269] Modules linked in: tun binfmt_misc nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables xt_mark xt_REDIRECT xt_limit xt_conntrack xt_nat xt_tcpudp iptable_mangle iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_filter ip_tables x_tables sit ip_tunnel nvidia(PO) stb6100 stv090x cx88_dvb videobuf_dvb cx88_vp3054_i2c tuner kvm_amd kvm cx8802 k10temp cx8800 cx88xx btcx_risc videobuf_dma_sg videobuf_core usb_storage ds2490 usbhid ftdi_sio cx23885 tveeprom cx2341x videobuf2_dvb videobuf2_core videobuf2_dma_sg videobuf2_memops asus_atk0110 snd_emu10k1 snd_hwdep snd_util_mem snd_ac97_codec ac97_bus snd_rawmidi snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd w1_therm wire ipv6
[20712.990301] CPU: 2 PID: 26942 Comm: vb2-cx23885[0] Tainted: P B W O 3.18.0-rc5-00001-gb3652d1 #2
[20712.990303] Hardware name: System manufacturer System Product Name/M4A785TD-V EVO, BIOS 2105 07/23/2010
[20712.990305] ffffffff81765734 ffff880137683a78 ffffffff815b6b32 0000000000000006
[20712.990307] ffffea00009c3b60 ffff880137683aa8 ffffffff8108ec27 ffffffff81765712
[20712.990309] ffffffff8189c840 0000000000000246 ffffea00009c3b60 ffff880137683b78
[20712.990312] Call Trace:
[20712.990317] [<ffffffff815b6b32>] dump_stack+0x46/0x58
[20712.990321] [<ffffffff8108ec27>] bad_page+0xe9/0x107
[20712.990323] [<ffffffff810912ca>] get_page_from_freelist+0x3b2/0x505
[20712.990326] [<ffffffff8109150a>] __alloc_pages_nodemask+0xed/0x65f
[20712.990330] [<ffffffff81047a52>] ? ttwu_do_activate.constprop.78+0x57/0x5c
[20712.990332] [<ffffffff81049ff3>] ? try_to_wake_up+0x21b/0x22d
[20712.990336] [<ffffffff810070f4>] dma_generic_alloc_coherent+0x6e/0xf5
[20712.990339] [<ffffffff810261a9>] gart_alloc_coherent+0x105/0x114
[20712.990341] [<ffffffff81025963>] ? flush_gart+0x39/0x3d
[20712.990343] [<ffffffff810260a4>] ? gart_map_sg+0x3a0/0x3a0
[20712.990349] [<ffffffffa0141a1e>] cx23885_risc_databuffer+0xa7/0x133 [cx23885]
[20712.990354] [<ffffffffa0142764>] cx23885_buf_prepare+0x121/0x134 [cx23885]
[20712.990359] [<ffffffffa0144210>] buffer_prepare+0x14/0x16 [cx23885]
[20712.990363] [<ffffffffa011f101>] __buf_prepare+0x190/0x279 [videobuf2_core]
[20712.990366] [<ffffffffa011d906>] ? vb2_queue_or_prepare_buf+0xb8/0xc0 [videobuf2_core]
[20712.990369] [<ffffffffa011f34b>] vb2_internal_qbuf+0x51/0x1e5 [videobuf2_core]
[20712.990372] [<ffffffffa0120537>] vb2_thread+0x199/0x1f6 [videobuf2_core]
[20712.990376] [<ffffffffa012039e>] ? vb2_fop_write+0xdf/0xdf [videobuf2_core]
[20712.990379] [<ffffffff81043e61>] kthread+0xdf/0xe7
[20712.990381] [<ffffffff81043d82>] ? kthread_create_on_node+0x16d/0x16d
[20712.990384] [<ffffffff815bd46c>] ret_from_fork+0x7c/0xb0
[20712.990386] [<ffffffff81043d82>] ? kthread_create_on_node+0x16d/0x16d
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Mariusz Bialonczyk <manio@skyboo.net>
Tested-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
length is the size of the buffer, not the payload. That's set using
vb2_set_plane_payload().
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Cc: <stable@vger.kernel.org> # for v3.15 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Signed-off-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The IRQs have to be acknowledged before they are serviced, otherwise some events
may be skipped. Also, acknowledging IRQs just before returning from the handler
doesn't leave enough time for the device to deassert the INTx line, and for
bridges to propagate this change. This resulted in twice the IRQ rate on ARMv6
dual core CPU.
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Acked-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Tested-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch adds hwmod support for ADC on AM43xx. Since clockdomain
and offsets of adc_tsc are different from AM33xx, ADC data has been
directly added to AM43xx hwmod file.
Signed-off-by: Vignesh R <vigneshr@ti.com>
[paul@pwsan.com: fixed spelling of "Anolog"; converted spaces to tabs]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs into for-linus
"The biggest change is to rename the filesystem from "overlayfs" to "overlay".
This will allow legacy overlayfs to be easily carried by distros alongside the
new mainline one. Also fix a couple of copy-up races and allow escaping comma
character in filenames."
The last bit is about commas in pathname mount options...
|
|
As the ARCH_AT91RM9200 is removed because being !DT, we use
the SOC_AT91RM9200 variant. This option can certainly be removed
once the ST driver is reworked a bit.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
|
|
Second part of at91rm9200 legacy !DT removal. This is the core !DT support
removal for this Atmel SoC.
Note that from now on, the Kconfig.non_dt file and its specialized options are
completely removed.
Use the Device Tree for running this board with newer kernels.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
|
|
Remove old board files that use at91rm9200 Atmel SoC. The
device tree is mature on this SoCs. It must be used now.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
|
|
There are no users of the struct hw_pci.add_bus() or .remove_bus() methods,
so remove the pointers from hw_pci. That makes pcibios_add_bus() and
pcibios_remove_bus() themselves superfluous, so remove them as well.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use xilinx_pcie_msi_chip, not xilinx_pcie_msi_controller]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use struct rcar_msi.chip, not ctrl]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use dw_pcie_msi_chip, not dw_pcie_msi_controller]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use struct tegra_msi.chip, not ctrl]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Currently ARM associates an MSI controller with a PCI bus by defining
pcibios_add_bus() and using it to call a struct hw_pci.add_bus() method.
That method sets the struct pci_bus "msi" member. That's unwieldy and
unnecessarily couples MSI with the PCI enumeration code.
On ARM, all devices under the same PCI host bridge share an MSI controller,
so add an msi_controller pointer to the struct pci_sys_data and implement
pcibios_msi_controller() to retrieve it.
This is a step toward moving the msi_controller pointer into the generic
struct pci_host_bridge.
[bhelgaas: changelog, take pci_dev instead of pci_bus]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
According to the manuals I have, XScale auxiliary register should be
reached with opc_2 = 1 instead of crn = 1. cpu_xscale_proc_init
correctly uses c1, c0, 1 arguments, but cpu_xscale_do_suspend and
cpu_xscale_do_resume use c1, c1, 0. Correct suspend/resume functions to
also use c1, c0, 1.
The issue was primarily noticed thanks to qemu reporing "unsupported
instruction" on the pxa suspend path. Confirmed in PXA210/250 and PXA255
XScale Core manuals and in PXA270 and PXA320 Developers Guides.
Harware tested by me on tosa (pxa255). Robert confirmed on pxa270 board.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Exynos7 has a similar serial controller to that present in older Samsung
SoCs. To re-use the existing serial driver on Exynos7 we need to have
SERIAL_SAMSUNG_UARTS_4 and SERIAL_SAMSUNG_UARTS selected. This is not
possible because these symbols are dependent on PLAT_SAMSUNG which is
not present for the ARMv8 based exynos7.
Change the dependency of these symbols from PLAT_SAMSUNG to the serial
driver thus making it available on exynos7. As the existing platform
specific code making use of these symbols is related to uart driver this
change in dependency should not cause any issues.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/ras
Merge RAS updates from Tony Luck:
"Handle all uncorrected error reports in the same way (soft offline
the page). We used to only do that for SRAO (software recoverable
action optional) machine checks, but it makes sense to also do it
for UCNA (UnCorrected No Action) logs found by CMCI or polling."
|
|
Translation faults that occur due to the input address being outside
of the address range mapped by the relevant base register are reported
as level 0 faults in ESR.DFSC.
If the faulting access cannot be resolved by the kernel (e.g. because
it is not mapped by a vma), then we report "input address range fault"
on the console. This was fine until we added support for 48-bit VAs,
which actually place PGDs at level 0 and can trigger faults for invalid
addresses that are within the range of the page tables.
This patch changes the string to report "level 0 translation fault",
which is far less confusing.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This patch fixes XMOS DSD sample format to DSD_U32_BE and also adds
DSD_U16_BE and DSD_U32_BE sample formats.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Acked-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The regulator framework has a set of helpers functions to be used when
the system is entering and leaving from suspend but these are not called
on Exynos platforms. This means that the .set_suspend_* function handlers
defined by regulator drivers are not called when the system is suspended.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
