| Age | Commit message (Collapse) | Author |
|---|
|
Use generic node name for the SoM GPIO expander, following the
Devicetree Specification generic node names recommendation.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add gpio expander node to the device tree and the related nodes.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the embedded controller node to the device tree, this is required
for reset and power-off functionalities.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Configure correctly the FAN pwm output (inverted).
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Using the MDIO pins with Open Drain causes spec violations of the
signals. Revert the changes.
This is similar to commit 14e66e4b13221 ("Revert "arm64: dts:
imx93-tqma9352-mba93xxca: enable Open Drain for MDIO"")
Fixes: e5bc07026f94 ("arm64: add initial device tree for TQMa93xx/MBa91xxCA")
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add initial support for TQMa95xxSA module compatible to SMARC-2.
There is a common device tree for all variants with e.g. reduced CPU count.
It supports LPUART7 for console, CAN, PCIe I2C, SPI, USB3.0, USB2.0, Audio,
SDHC1/2 and QSPI as storage.
[1] https://www.tq-group.com/en/products/tq-embedded/arm-architecture/tqma95xxsa/
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit 3c3606793f7e ("dt-bindings: wireless: bcm4329-fmac: Use
wireless-controller.yaml schema"), bindings expect 'wifi' as node name:
imx8mm-var-som-symphony.dtb: bcrmf@1: $nodename:0: 'bcrmf@1' does not match '^wifi(@.*)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds support for TQMa8XQPS and TQMa8XDPS modules on MB-SMARC-2 board.
As the only difference is the mounted SoC, both module and baseboard
files are shared.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This overlay configures IMX219 MIPI-CSI-2 camera attached to ISP1.
Also add additional overlay both using LVDS display and camera.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds an overlay for the supported LVDS display tianma tm070jvhg33.
The LVDS interface is the same as for MBa8MPxL so the already existing
overlay can be reused on this platform.
Signed-off-by: Martin Schmiedel <Martin.Schmiedel@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the minimal board dts support for i.MX943 EVK. Only the console uart,
SD & eMMC are enabled for linux basic boot.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the minimal dtsi support for i.MX943. i.MX943 is the first SoC of
i.MX94 Family, create a common dtsi for the whole i.MX94 family, and the
specific dtsi part for i.MX943.
The clock, power domain and perf index need to be used by the device nodes
for resource reference, add them along with the dtsi support.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The needed drivers to support PCIe for i.MX 8QXP have been
added.
Configure PCIe for the Colibri iMX8X SoM.
The pcieb block is connected to the on module Wi-Fi/BT module.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move pinctrl_uart1 to keep nodes in alphabetical order. No functional
changes.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the carrier-board Micrel KSZ8081 Ethernet PHY. This is a
10/100Mbit PHY connected to the EQOS interface and shares MDIO bus with
the Ethernet PHY located on the SoM (FEC interface).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for I2S audio found on phyBOARD-Segin-i.MX93. Audio codec
TLV320AIC3007 is connected to SAI1 interface as a DAI master. MCLK is
provided from the SAI's internal audio PLL (19.2 MHz).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for both USB controllers. Set first controller in OTG mode
(USB micro-AB connector X8) and the second one in host mode (USB type A
connector X7) by default.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for CAN networking on phyBOARD-Segin-i.MX93 via the flexcan1
interface. The CAN PHY chip SN65HVD234D used on the board is compatible
with the TCAN1043 driver using the generic "can-transceiver-phy" and is
capable of up to 1Mbps data rate.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for RTC connected via I2C on phyBOARD-Segin-i.MX93. Set
default RTC by configuring the aliases.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
ERR052021
Implement fix for i.MX 93 silicon errata ERR052021.
ERR052021 uSDHC: Sometimes uSDHC does not work under VDD_SOC low
drive mode and nominal mode
Description:
uSDHC PADs have one integration issue.
When CMD/DATA lines direction change from output to input, uSDHC
controller begin sampling, the integration issue will make input
enable signal from uSDHC propagated to the PAD with a long delay,
thus the new input value on the pad comes to uSDHC lately. The
uSDHC sampled the old input value and the sampling result is wrong.
Workaround:
Set uSDHC CMD/DATA PADs iomux register SION bit to 1, then PADs will
propagate input to uSDHC with no delay, so correct value is sampled.
This issue will wrongly trigger the start bit when sample the USDHC
command response, cause the USDHC trigger command CRC/index/endbit
error, which will finally impact the tuning pass window, especially
will impact the standard tuning logic, and can't find a correct delay
cell to get the best timing.
Based on commit bb89601282fc ("arm64: dts: imx93-11x11-evk: set SION for
cmd and data pad of USDHC").
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Until now, all usdhc2 (SD-card) pinctrl labels pointed to one pinctrl
group "usdhc2grp" which was overwritten twice by the 100 and 200 MHz
modes. Fix this by using unique pinctrl names.
Additionally, adjust MX93_PAD_SD2_CLK__USDHC2_CLK pad drive-strength
according to values obtained by measurements from the PHYTEC hardware
department to improve signal integrity.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add disable-wp flag (write-protect) to usdhc2 node (SD-card) to get rid
of the following kernel boot warning:
host does not support reading read-only switch, assuming write-enable
Micro SD cards can't be physically write-protected like full-sized
cards anyways.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Drop redundant 'no-1-8-v' flag from usdhc1 (eMMC) node. Flag is now set
by default in the SOM include file (imx93-phycore-som.dtsi).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The phyCORE-i.MX93 SoM comes in two variants, one with VDD_IO set to
3.3V and the other variant to 1.8V. The 3.3V variant can only support
DDR52 mode, while 1.8V variant is capable of HS400ES eMMC mode. The
information about VDD_IO option is encoded in the SoM's EEPROM. EEPROM
is read in the bootloader and bootloader clears the "no-1-8-v" flag in
case of 1.8V SoM variant is detected. Thus add property 'no-1-8-v' by
default to usdhc1 (eMMC) node and let bootloader handle the flag. In
case EEPROM is erased or read-out fails, flag "no-1-8-v" also ensures
fall-back compatibility with both SoM variants.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Improve eMMC on phyCORE-i.MX93 SOM by adding 100MHz and 200MHz pinctrl
modes. This enables to use eMMC at enhanced data rates (e.g. HS400).
While at it, apply a workaround for the i.MX93 chip errata ERR052021.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is already an external pull-down resistor on the LED output line.
It makes no sense to have both pull-down and pull-up resistors enabled
at the same time. Thus disable the internal pull-up.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the EEPROM chip available on I2C3 bus (address 0x50),
used for the PHYTEC SOM detection.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
PMIC driver for PCA9451A used on phyCORE-i.MX93 SOM is available since
commit 5edeb7d31262 ("regulator: pca9450: add pca9451a support"). Add
support for it in the SOM device-tree.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
When running in nominal drive mode, the maximum allowed frequency for
the NoC is 800MHz, but the OPP table for the i.MX8MP interconnect device
listed the 1GHz operating point for the NoC, regardless of the active
mode.
The newly introduced imx8mp-nominal.dtsi header reconfigures the clock
controller to observe nominal drive mode limits, so have it modify the
maximum NoC OPP as well.
Fixes: 255fbd9eabe7 ("arm64: dts: imx8mp: Add optional nominal drive mode DTSI")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Libra board has an LVDS connector. Add an overlay for an
etml1010g3dra LVDS panel supported for the phyCORE-i.MX 8M Plus that may
be connected to it.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add device tree for the Libra-i.MX 8M Plus FPSC board. The Libra is a
pure development board and has hardware to support FPSC-24-A.0 set of
features. It can be populated with the phyCORE-i.MX 8M Plus SoM to form
a SBC.
The phyCORE-i.MX 8M Plus FPSC [1] SoM uses only a subset of the hardware
features the Libra board provides. The phyCORE-i.MX8MP FPSC itself is a
System on Module based on the i.MX 8M Plus SoC utilizing the Future
Proof Solder Core [2] standard.
To be able to easily map FPSC interface names to SoC interfaces, the
FPSC interface names are added as inline comments. Example:
&i2c5 { /* FPSC I2C4 */
pinctrl-0 = <&pinctrl_i2c5>;
[...]
};
Here, I2C4 is the FPSC interface name. The i2c5 instance of the i.MX 8M Plus
SoC is used to fulfill the i2c functionality and its signals are routed
to the FPSC I2C4 signal pins:
pinctrl_i2c5: i2c5grp {
fsl,pins = <
MX8MP_IOMUXC_SPDIF_RX__I2C5_SDA 0x400001c2 /* I2C4_SDA */
MX8MP_IOMUXC_SAI5_RXD0__I2C5_SCL 0x400001c2 /* I2C4_SCL */
>;
};
The features are almost identical to the existing phyCORE-i.MX 8M Plus
SoM (dts: imx8mp-phycore-som.dtsi), but the pin muxing is different due
to the FPSC standard as well as 1.8V IO voltage instead of 3.3V.
[1] https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-8m-plus-fpsc/
[2] https://www.phytec.eu/en/produkte/system-on-modules/fpsc/
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Define vqmmc regulator-gpio for usdhc2 with vin-supply
coming from LDO5.
Without this definition LDO5 will be powered down, disabling
SD card after bootup. This has been introduced in commit
f5aab0438ef1 ("regulator: pca9450: Fix enable register for LDO5").
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Fixes: f5aab0438ef1 ("regulator: pca9450: Fix enable register for LDO5")
Tested-by: Manuel Traut <manuel.traut@mt.com>
Reviewed-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@mt.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add pcie[0,1]-ep nodes and apply imx-pcie1-ep overlay file.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add pcie0-ep node for i.MX8QM.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add pcie0-ep node information and apply pcie0-ep overlay file.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Create imx95-15x15-evk pcie0-ep and imx95-19x19-evk pcie[0,1]-ep dtb files.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use common imx-pcie0-ep.dtso for imx8mp-evk-pcie-ep and
imx8qxp-mek-pcie-ep. No functional change.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use unified pcie0 label and add pcie0-ep node.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX8DXL use difference irq number for PCIe EP DMA.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add unified pcie<n> and pcie<n>_ep label for existed chipes to prepare
applied one overay file to enable EP function.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The needed drivers to support PCIe and SATA for i.MX 8QM have been
added.
Configure them for the Apalis iMX8 SoM.
The pciea and pcieb blocks each get a single PCIe lane, pciea is
available on the carrier boards while pcieb is connected to the
on module Wi-Fi/BT module.
The SATA lane is available on the carrier boards.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Using the MDIO pins with Open Drain causes spec violations of the
signals. Revert the changes.
This reverts commit 315d7f301e234b99c1b9619f0b14cf288dc7c33f.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Using the MDIO pins with Open Drain causes spec violations of the
signals. Revert the changes.
This reverts commit 9015397c2f2d9d327c0cf88d74e39c4858cb4912.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the interrupts and wakeup-source to allow the external RTC to be
used as an alarm.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the interrupts and wakeup-source to allow the external RTC to be
used as an alarm.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the interrupts and wakeup-source to allow the external RTC to be
used as an alarm.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Ethernet PHY setup currently assumes that the bootloader will take the
PHY out of reset, but this behavior is not guaranteed across all
bootloaders. Add the reset GPIO to ensure the kernel can properly control
the PHY reset line.
Also configure the PHY IRQ GPIO to enable interrupt-driven link status
reporting, instead of relying on polling.
This ensures more reliable Ethernet initialization and improves PHY event
handling.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Ethernet PHY setup currently assumes that the bootloader will take the
PHY out of reset, but this behavior is not guaranteed across all
bootloaders. Add the reset GPIO to ensure the kernel can properly control
the PHY reset line.
Also configure the PHY IRQ GPIO to enable interrupt-driven link status
reporting, instead of relying on polling.
This ensures more reliable Ethernet initialization and improves PHY event
handling.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The HDMI bridge chip fails to generate an audio source due to the SAI5
master clock (MCLK) direction not being set to output. This prevents proper
clocking of the HDMI audio interface.
Add the `fsl,sai-mclk-direction-output` property to the SAI5 node to ensure
the MCLK is driven by the SoC, resolving the HDMI sound issue.
Fixes: 1d6880ceef43 ("arm64: dts: imx8mn-beacon: Add HDMI video with sound")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The HDMI bridge chip fails to generate an audio source due to the SAI5
master clock (MCLK) direction not being set to output. This prevents proper
clocking of the HDMI audio interface.
Add the `fsl,sai-mclk-direction-output` property to the SAI5 node to ensure
the MCLK is driven by the SoC, resolving the HDMI sound issue.
Fixes: 8ad7d14d99f3 ("arm64: dts: imx8mm-beacon: Add HDMI video with sound")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
