| Age | Commit message (Collapse) | Author |
|---|
|
Pull SoC devicetree updates from Arnd Bergmann:
"There is new support for additional on-chip devices on Apple,
Mediatek, Renesas, Rockchip, Samsung, Google, TI, ST, Nvidia and
Amlogic devices.
The Arm Morello reference platform gets a devicetree for booting in
normal aarch64 mode. The hardware supports experimental CHERI support,
which requires a modified kernel.
The AMD (formerly Xilinx) Versal NET SoC gets added, this is a
combined FPGA with Cortex-A78 CPUs in a SoC.
Six new ST STM32MP2 SoC variants are added. Like the earlier
STM32MP25, the MP211, MP213, MP215, MP231, MP233 and MP235 models are
based on one or two Cortex-A35 cores but each feature a different set
of I/O devices.
Mediatek MT8370 is a minor variation of MT8390 with fewer CPU and GPU
cores
Apple T2 is the baseboard management controller on earlier Intel CPU
based Macs, with 16 models now gaining initial support.
All the above come with dts files for the reference boards. In
addition, these boards are added for the SoCs that are already
supported:
- The Milk-V Jupiter board based on SpacemiT K1/M1
- NetCube Systems Kumquat board based on the 32-bit Allwinner V3s SoC
- Three boards based on 32-bit stm32mp1
- 11 distinct board variants from Toradex and one from Variscite, all
based on i.MX6
- Google Pixel Pro 6 phone based on gs101 (Tensor)
- Three additional variants of the i.MX8MP based "Skov" board
- A second variant of the i.MX95 EVK board
- Two boards based on Renesas SoCs
- Four boards based the Rockchip RK35xx series, plus the RK3588 'MNT
Reform 2' laptop"
* tag 'soc-dt-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (538 commits)
arm64: dts: Add gpio_intc node for Amlogic A5 SoCs
arm64: dts: Add gpio_intc node for Amlogic A4 SoCs
arm64: dts: hi3660: Add property for fixing CPUIdle
arm64: dts: rockchip: remove ethm0_clk0_25m_out from Sige5 gmac0
arm64: dts: marvell: Use preferred node names for "simple-bus"
arm64: dts: marvell: Drop unused CP11X_TYPE define
arm64: dts: marvell: Move arch timer and pmu nodes to top-level
arm64: dts: rockchip: Fix PWM pinctrl names
arm64: dts: rockchip: fix RK3576 SCMI clock IDs
dt-bindings: clock: rk3576: add SCMI clocks
arm64: dts: rockchip: Fix pcie reset gpio on Orange Pi 5 Max
arm64: dts: amd/seattle: Drop undocumented "spi-controller" properties
arm64: dts: amd/seattle: Fix bus, mmc, and ethernet node names
arm64: dts: amd/seattle: Move and simplify fixed clocks
arm64: dts: amd/seattle: Base Overdrive B1 on top of B0 version
arm64: dts: rockchip: Enable HDMI audio output for ArmSoM Sige7
arm64: dts: rockchip: Enable onboard eMMC on Radxa E20C
arm64: dts: rockchip: Add SDHCI controller for RK3528
arm64: dts: rockchip: Remove bluetooth node from rock-3a
arm64: dts: rockchip: Move rk356x scmi SHMEM to reserved memory
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull CRC updates from Eric Biggers:
"Another set of improvements to the kernel's CRC (cyclic redundancy
check) code:
- Rework the CRC64 library functions to be directly optimized, like
what I did last cycle for the CRC32 and CRC-T10DIF library
functions
- Rewrite the x86 PCLMULQDQ-optimized CRC code, and add VPCLMULQDQ
support and acceleration for crc64_be and crc64_nvme
- Rewrite the riscv Zbc-optimized CRC code, and add acceleration for
crc_t10dif, crc64_be, and crc64_nvme
- Remove crc_t10dif and crc64_rocksoft from the crypto API, since
they are no longer needed there
- Rename crc64_rocksoft to crc64_nvme, as the old name was incorrect
- Add kunit test cases for crc64_nvme and crc7
- Eliminate redundant functions for calculating the Castagnoli CRC32,
settling on just crc32c()
- Remove unnecessary prompts from some of the CRC kconfig options
- Further optimize the x86 crc32c code"
* tag 'crc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux: (36 commits)
x86/crc: drop the avx10_256 functions and rename avx10_512 to avx512
lib/crc: remove unnecessary prompt for CONFIG_CRC64
lib/crc: remove unnecessary prompt for CONFIG_LIBCRC32C
lib/crc: remove unnecessary prompt for CONFIG_CRC8
lib/crc: remove unnecessary prompt for CONFIG_CRC7
lib/crc: remove unnecessary prompt for CONFIG_CRC4
lib/crc7: unexport crc7_be_syndrome_table
lib/crc_kunit.c: update comment in crc_benchmark()
lib/crc_kunit.c: add test and benchmark for crc7_be()
x86/crc32: optimize tail handling for crc32c short inputs
riscv/crc64: add Zbc optimized CRC64 functions
riscv/crc-t10dif: add Zbc optimized CRC-T10DIF function
riscv/crc32: reimplement the CRC32 functions using new template
riscv/crc: add "template" for Zbc optimized CRC functions
x86/crc: add ANNOTATE_NOENDBR to suppress objtool warnings
x86/crc32: improve crc32c_arch() code generation with clang
x86/crc64: implement crc64_be and crc64_nvme using new template
x86/crc-t10dif: implement crc_t10dif using new template
x86/crc32: implement crc32_le using new template
x86/crc: add "template" for [V]PCLMULQDQ based CRC functions
...
|
|
Pull kvm updates from Paolo Bonzini:
"ARM:
- Nested virtualization support for VGICv3, giving the nested
hypervisor control of the VGIC hardware when running an L2 VM
- Removal of 'late' nested virtualization feature register masking,
making the supported feature set directly visible to userspace
- Support for emulating FEAT_PMUv3 on Apple silicon, taking advantage
of an IMPLEMENTATION DEFINED trap that covers all PMUv3 registers
- Paravirtual interface for discovering the set of CPU
implementations where a VM may run, addressing a longstanding issue
of guest CPU errata awareness in big-little systems and
cross-implementation VM migration
- Userspace control of the registers responsible for identifying a
particular CPU implementation (MIDR_EL1, REVIDR_EL1, AIDR_EL1),
allowing VMs to be migrated cross-implementation
- pKVM updates, including support for tracking stage-2 page table
allocations in the protected hypervisor in the 'SecPageTable' stat
- Fixes to vPMU, ensuring that userspace updates to the vPMU after
KVM_RUN are reflected into the backing perf events
LoongArch:
- Remove unnecessary header include path
- Assume constant PGD during VM context switch
- Add perf events support for guest VM
RISC-V:
- Disable the kernel perf counter during configure
- KVM selftests improvements for PMU
- Fix warning at the time of KVM module removal
x86:
- Add support for aging of SPTEs without holding mmu_lock.
Not taking mmu_lock allows multiple aging actions to run in
parallel, and more importantly avoids stalling vCPUs. This includes
an implementation of per-rmap-entry locking; aging the gfn is done
with only a per-rmap single-bin spinlock taken, whereas locking an
rmap for write requires taking both the per-rmap spinlock and the
mmu_lock.
Note that this decreases slightly the accuracy of accessed-page
information, because changes to the SPTE outside aging might not
use atomic operations even if they could race against a clear of
the Accessed bit.
This is deliberate because KVM and mm/ tolerate false
positives/negatives for accessed information, and testing has shown
that reducing the latency of aging is far more beneficial to
overall system performance than providing "perfect" young/old
information.
- Defer runtime CPUID updates until KVM emulates a CPUID instruction,
to coalesce updates when multiple pieces of vCPU state are
changing, e.g. as part of a nested transition
- Fix a variety of nested emulation bugs, and add VMX support for
synthesizing nested VM-Exit on interception (instead of injecting
#UD into L2)
- Drop "support" for async page faults for protected guests that do
not set SEND_ALWAYS (i.e. that only want async page faults at CPL3)
- Bring a bit of sanity to x86's VM teardown code, which has
accumulated a lot of cruft over the years. Particularly, destroy
vCPUs before the MMU, despite the latter being a VM-wide operation
- Add common secure TSC infrastructure for use within SNP and in the
future TDX
- Block KVM_CAP_SYNC_REGS if guest state is protected. It does not
make sense to use the capability if the relevant registers are not
available for reading or writing
- Don't take kvm->lock when iterating over vCPUs in the suspend
notifier to fix a largely theoretical deadlock
- Use the vCPU's actual Xen PV clock information when starting the
Xen timer, as the cached state in arch.hv_clock can be stale/bogus
- Fix a bug where KVM could bleed PVCLOCK_GUEST_STOPPED across
different PV clocks; restrict PVCLOCK_GUEST_STOPPED to kvmclock, as
KVM's suspend notifier only accounts for kvmclock, and there's no
evidence that the flag is actually supported by Xen guests
- Clean up the per-vCPU "cache" of its reference pvclock, and instead
only track the vCPU's TSC scaling (multipler+shift) metadata (which
is moderately expensive to compute, and rarely changes for modern
setups)
- Don't write to the Xen hypercall page on MSR writes that are
initiated by the host (userspace or KVM) to fix a class of bugs
where KVM can write to guest memory at unexpected times, e.g.
during vCPU creation if userspace has set the Xen hypercall MSR
index to collide with an MSR that KVM emulates
- Restrict the Xen hypercall MSR index to the unofficial synthetic
range to reduce the set of possible collisions with MSRs that are
emulated by KVM (collisions can still happen as KVM emulates
Hyper-V MSRs, which also reside in the synthetic range)
- Clean up and optimize KVM's handling of Xen MSR writes and
xen_hvm_config
- Update Xen TSC leaves during CPUID emulation instead of modifying
the CPUID entries when updating PV clocks; there is no guarantee PV
clocks will be updated between TSC frequency changes and CPUID
emulation, and guest reads of the TSC leaves should be rare, i.e.
are not a hot path
x86 (Intel):
- Fix a bug where KVM unnecessarily reads XFD_ERR from hardware and
thus modifies the vCPU's XFD_ERR on a #NM due to CR0.TS=1
- Pass XFD_ERR as the payload when injecting #NM, as a preparatory
step for upcoming FRED virtualization support
- Decouple the EPT entry RWX protection bit macros from the EPT
Violation bits, both as a general cleanup and in anticipation of
adding support for emulating Mode-Based Execution Control (MBEC)
- Reject KVM_RUN if userspace manages to gain control and stuff
invalid guest state while KVM is in the middle of emulating nested
VM-Enter
- Add a macro to handle KVM's sanity checks on entry/exit VMCS
control pairs in anticipation of adding sanity checks for secondary
exit controls (the primary field is out of bits)
x86 (AMD):
- Ensure the PSP driver is initialized when both the PSP and KVM
modules are built-in (the initcall framework doesn't handle
dependencies)
- Use long-term pins when registering encrypted memory regions, so
that the pages are migrated out of MIGRATE_CMA/ZONE_MOVABLE and
don't lead to excessive fragmentation
- Add macros and helpers for setting GHCB return/error codes
- Add support for Idle HLT interception, which elides interception if
the vCPU has a pending, unmasked virtual IRQ when HLT is executed
- Fix a bug in INVPCID emulation where KVM fails to check for a
non-canonical address
- Don't attempt VMRUN for SEV-ES+ guests if the vCPU's VMSA is
invalid, e.g. because the vCPU was "destroyed" via SNP's AP
Creation hypercall
- Reject SNP AP Creation if the requested SEV features for the vCPU
don't match the VM's configured set of features
Selftests:
- Fix again the Intel PMU counters test; add a data load and do
CLFLUSH{OPT} on the data instead of executing code. The theory is
that modern Intel CPUs have learned new code prefetching tricks
that bypass the PMU counters
- Fix a flaw in the Intel PMU counters test where it asserts that an
event is counting correctly without actually knowing what the event
counts on the underlying hardware
- Fix a variety of flaws, bugs, and false failures/passes
dirty_log_test, and improve its coverage by collecting all dirty
entries on each iteration
- Fix a few minor bugs related to handling of stats FDs
- Add infrastructure to make vCPU and VM stats FDs available to tests
by default (open the FDs during VM/vCPU creation)
- Relax an assertion on the number of HLT exits in the xAPIC IPI test
when running on a CPU that supports AMD's Idle HLT (which elides
interception of HLT if a virtual IRQ is pending and unmasked)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (216 commits)
RISC-V: KVM: Optimize comments in kvm_riscv_vcpu_isa_disable_allowed
RISC-V: KVM: Teardown riscv specific bits after kvm_exit
LoongArch: KVM: Register perf callbacks for guest
LoongArch: KVM: Implement arch-specific functions for guest perf
LoongArch: KVM: Add stub for kvm_arch_vcpu_preempted_in_kernel()
LoongArch: KVM: Remove PGD saving during VM context switch
LoongArch: KVM: Remove unnecessary header include path
KVM: arm64: Tear down vGIC on failed vCPU creation
KVM: arm64: PMU: Reload when resetting
KVM: arm64: PMU: Reload when user modifies registers
KVM: arm64: PMU: Fix SET_ONE_REG for vPMC regs
KVM: arm64: PMU: Assume PMU presence in pmu-emul.c
KVM: arm64: PMU: Set raw values from user to PM{C,I}NTEN{SET,CLR}, PMOVS{SET,CLR}
KVM: arm64: Create each pKVM hyp vcpu after its corresponding host vcpu
KVM: arm64: Factor out pKVM hyp vcpu creation to separate function
KVM: arm64: Initialize HCRX_EL2 traps in pKVM
KVM: arm64: Factor out setting HCRX_EL2 traps into separate function
KVM: x86: block KVM_CAP_SYNC_REGS if guest state is protected
KVM: x86: Add infrastructure for secure TSC
KVM: x86: Push down setting vcpu.arch.user_set_tsc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull VDSO infrastructure updates from Thomas Gleixner:
- Consolidate the VDSO storage
The VDSO data storage and data layout has been largely architecture
specific for historical reasons. That increases the maintenance
effort and causes inconsistencies over and over.
There is no real technical reason for architecture specific layouts
and implementations. The architecture specific details can easily be
integrated into a generic layout, which also reduces the amount of
duplicated code for managing the mappings.
Convert all architectures over to a unified layout and common mapping
infrastructure. This splits the VDSO data layout into subsystem
specific blocks, timekeeping, random and architecture parts, which
provides a better structure and allows to improve and update the
functionalities without conflict and interaction.
- Rework the timekeeping data storage
The current implementation is designed for exposing system
timekeeping accessors, which was good enough at the time when it was
designed.
PTP and Time Sensitive Networking (TSN) change that as there are
requirements to expose independent PTP clocks, which are not related
to system timekeeping.
Replace the monolithic data storage by a structured layout, which
allows to add support for independent PTP clocks on top while reusing
both the data structures and the time accessor implementations.
* tag 'timers-vdso-2025-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
sparc/vdso: Always reject undefined references during linking
x86/vdso: Always reject undefined references during linking
vdso: Rework struct vdso_time_data and introduce struct vdso_clock
vdso: Move architecture related data before basetime data
powerpc/vdso: Prepare introduction of struct vdso_clock
arm64/vdso: Prepare introduction of struct vdso_clock
x86/vdso: Prepare introduction of struct vdso_clock
time/namespace: Prepare introduction of struct vdso_clock
vdso/namespace: Rename timens_setup_vdso_data() to reflect new vdso_clock struct
vdso/vsyscall: Prepare introduction of struct vdso_clock
vdso/gettimeofday: Prepare helper functions for introduction of struct vdso_clock
vdso/gettimeofday: Prepare do_coarse_timens() for introduction of struct vdso_clock
vdso/gettimeofday: Prepare do_coarse() for introduction of struct vdso_clock
vdso/gettimeofday: Prepare do_hres_timens() for introduction of struct vdso_clock
vdso/gettimeofday: Prepare do_hres() for introduction of struct vdso_clock
vdso/gettimeofday: Prepare introduction of struct vdso_clock
vdso/helpers: Prepare introduction of struct vdso_clock
vdso/datapage: Define vdso_clock to prepare for multiple PTP clocks
vdso: Make vdso_time_data cacheline aligned
arm64: Make asm/cache.h compatible with vDSO
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer cleanups from Thomas Gleixner:
"A treewide hrtimer timer cleanup
hrtimers are initialized with hrtimer_init() and a subsequent store to
the callback pointer. This turned out to be suboptimal for the
upcoming Rust integration and is obviously a silly implementation to
begin with.
This cleanup replaces the hrtimer_init(T); T->function = cb; sequence
with hrtimer_setup(T, cb);
The conversion was done with Coccinelle and a few manual fixups.
Once the conversion has completely landed in mainline, hrtimer_init()
will be removed and the hrtimer::function becomes a private member"
* tag 'timers-cleanups-2025-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (100 commits)
wifi: rt2x00: Switch to use hrtimer_update_function()
io_uring: Use helper function hrtimer_update_function()
serial: xilinx_uartps: Use helper function hrtimer_update_function()
ASoC: fsl: imx-pcm-fiq: Switch to use hrtimer_setup()
RDMA: Switch to use hrtimer_setup()
virtio: mem: Switch to use hrtimer_setup()
drm/vmwgfx: Switch to use hrtimer_setup()
drm/xe/oa: Switch to use hrtimer_setup()
drm/vkms: Switch to use hrtimer_setup()
drm/msm: Switch to use hrtimer_setup()
drm/i915/request: Switch to use hrtimer_setup()
drm/i915/uncore: Switch to use hrtimer_setup()
drm/i915/pmu: Switch to use hrtimer_setup()
drm/i915/perf: Switch to use hrtimer_setup()
drm/i915/gvt: Switch to use hrtimer_setup()
drm/i915/huc: Switch to use hrtimer_setup()
drm/amdgpu: Switch to use hrtimer_setup()
stm class: heartbeat: Switch to use hrtimer_setup()
i2c: Switch to use hrtimer_setup()
iio: Switch to use hrtimer_setup()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool updates from Ingo Molnar:
- The biggest change is the new option to automatically fail the build
on objtool warnings: CONFIG_OBJTOOL_WERROR.
While there are no currently known unfixed false positives left, such
an expansion in the severity of objtool warnings inevitably creates a
risk of build failures, so it's disabled by default and depends on
!COMPILE_TEST, so it shouldn't be enabled on
allyesconfig/allmodconfig builds and won't be forced on people who
just accept build-time defaults in 'make oldconfig'.
While the option is strongly recommended, only people who enable it
explicitly should see it.
(Josh Poimboeuf)
- Disable branch profiling in noinstr code with a broad brush that
includes all of arch/x86/ and kernel/sched/. (Josh Poimboeuf)
- Create backup object files on objtool errors and print exact objtool
arguments to make failure analysis easier (Josh Poimboeuf)
- Improve noreturn handling (Josh Poimboeuf)
- Improve rodata handling (Tiezhu Yang)
- Support jump tables, switch tables and goto tables on LoongArch
(Tiezhu Yang)
- Misc cleanups and fixes (Josh Poimboeuf, David Engraf, Ingo Molnar)
* tag 'objtool-core-2025-03-22' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
tracing: Disable branch profiling in noinstr code
objtool: Use O_CREAT with explicit mode mask
objtool: Add CONFIG_OBJTOOL_WERROR
objtool: Create backup on error and print args
objtool: Change "warning:" to "error:" for --Werror
objtool: Add --Werror option
objtool: Add --output option
objtool: Upgrade "Linked object detected" warning to error
objtool: Consolidate option validation
objtool: Remove --unret dependency on --rethunk
objtool: Increase per-function WARN_FUNC() rate limit
objtool: Update documentation
objtool: Improve __noreturn annotation warning
objtool: Fix error handling inconsistencies in check()
x86/traps: Make exc_double_fault() consistently noreturn
LoongArch: Enable jump table for objtool
objtool/LoongArch: Add support for goto table
objtool/LoongArch: Add support for switch table
objtool: Handle PC relative relocation type
objtool: Handle different entry size of rodata
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs sysv removal from Christian Brauner:
"This removes the sysv filesystem. We've discussed this various times.
It's time to try"
* tag 'vfs-6.15-rc1.sysv' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
sysv: Remove the filesystem
|
|
The immediate issue being fixed here is a nVMX bug where KVM fails to
detect that, after nested VM-Exit, L1 has a pending IRQ (or NMI).
However, checking for a pending interrupt accesses the legacy PIC, and
x86's kvm_arch_destroy_vm() currently frees the PIC before destroying
vCPUs, i.e. checking for IRQs during the forced nested VM-Exit results
in a NULL pointer deref; that's a prerequisite for the nVMX fix.
The remaining patches attempt to bring a bit of sanity to x86's VM
teardown code, which has accumulated a lot of cruft over the years. E.g.
KVM currently unloads each vCPU's MMUs in a separate operation from
destroying vCPUs, all because when guest SMP support was added, KVM had a
kludgy MMU teardown flow that broke when a VM had more than one 1 vCPU.
And that oddity lived on, for 18 years...
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into soc/dt
Minor improvements inDTS for v6.15
1. ARM Cirrus EP7211: Align GPIO node name to match what bindings
expect.
2. Loongson 2K1000: Drop incorrect spidev description, by pretending to
have there something else. This will have impact on the users of
DTS, because spidev will stop working, however no counter-proposals
of fixing this or even explaining this were proposed for half a year
after the patch was posted. Therefore drop incorrect hardware
description, hoping affected users will come if proper one, if needed.
* tag 'dt-cleanup-6.15' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
loongarch: dts: remove non-existent DAC from 2k1000-ref
ARM: dts: cirrus: ep7211: Align GPIO hog name with bindings
Link: https://lore.kernel.org/r/20250316144221.18240-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add selection for GUEST_PERF_EVENTS if KVM is enabled, also add perf
callback register when KVM module is loading.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Three architecture specific functions are added for the guest perf
feature, they are kvm_arch_vcpu_in_kernel(), kvm_arch_vcpu_get_ip()
and kvm_arch_pmi_in_guest().
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Pause-Loop Exiting is not supported by LoongArch hardware, nor is pv
spinlock feature. So function kvm_vcpu_on_spin() is not used. Function
kvm_arch_vcpu_preempted_in_kernel() is defined as a stub function here
since it is only called by unused function kvm_vcpu_on_spin().
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
PGD table for primary mmu keeps unchanged once VM is created, it is not
necessary to save PGD table pointer during VM context switch. And it can
be acquired when VM is created.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
arch/loongarch/kvm/ includes local headers with the double-quote form
(#include "..."). Also, TRACE_INCLUDE_PATH in arch/loongarch/kvm/trace.h
is relative to include/trace/.
Hence, the local header search path is unneeded.
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The point where the memory is released from memblock to the buddy
allocator is hidden inside arch-specific mem_init()s and the call to
memblock_free_all() is needlessly duplicated in every artiste cure and
after introduction of arch_mm_preinit() hook, mem_init() implementation on
many architecture only contains the call to memblock_free_all().
Pull memblock_free_all() call into mm_core_init() and drop mem_init() on
relevant architectures to make it more explicit where the free memory is
released from memblock to the buddy allocator and to reduce code
duplication in architecture specific code.
Link: https://lkml.kernel.org/r/20250313135003.836600-14-rppt@kernel.org
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com> [x86]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Tested-by: Mark Brown <broonie@kernel.org>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Betkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Guo Ren (csky) <guoren@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russel King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleinxer <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
high_memory defines upper bound on the directly mapped memory. This bound
is defined by the beginning of ZONE_HIGHMEM when a system has high memory
and by the end of memory otherwise.
All this is known to generic memory management initialization code that
can set high_memory while initializing core mm structures.
Add a generic calculation of high_memory to free_area_init() and remove
per-architecture calculation except for the architectures that set and use
high_memory earlier than that.
Link: https://lkml.kernel.org/r/20250313135003.836600-11-rppt@kernel.org
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com> [x86]
Tested-by: Mark Brown <broonie@kernel.org>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Betkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Guo Ren (csky) <guoren@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russel King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleinxer <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
max_mapnr is essentially the size of the memory map for systems that use
FLATMEM. There is no reason to calculate it in each and every architecture
when it's anyway calculated in alloc_node_mem_map().
Drop setting of max_mapnr from architecture code and set it once in
alloc_node_mem_map().
While on it, move definition of mem_map and max_mapnr to mm/mm_init.c so
there won't be two copies for MMU and !MMU variants.
Link: https://lkml.kernel.org/r/20250313135003.836600-10-rppt@kernel.org
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com> [x86]
Tested-by: Mark Brown <broonie@kernel.org>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Betkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Guo Ren (csky) <guoren@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russel King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleinxer <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
cmdline argument is not used in reserve_crashkernel_generic() so remove
it. Correspondingly, all the callers have been updated as well.
No functional change intended.
Link: https://lkml.kernel.org/r/20250131113830.925179-3-sourabhjain@linux.ibm.com
Signed-off-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Acked-by: Hari Bathini <hbathini@linux.ibm.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
ioremap_prot() currently accepts pgprot_val parameter as an unsigned long,
thus implicitly assuming that pgprot_val and pgprot_t could never be
bigger than unsigned long. But this assumption soon will not be true on
arm64 when using D128 pgtables. In 128 bit page table configuration,
unsigned long is 64 bit, but pgprot_t is 128 bit.
Passing platform abstracted pgprot_t argument is better as compared to
size based data types. Let's change the parameter to directly pass
pgprot_t like another similar helper generic_ioremap_prot().
Without this change in place, D128 configuration does not work on arm64 as
the top 64 bits gets silently stripped when passing the protection value
to this function.
Link: https://lkml.kernel.org/r/20250218101954.415331-1-anshuman.khandual@arm.com
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Co-developed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The zbud compressed pages allocator is rarely used, most users use
zsmalloc. zbud consumes much more memory (only stores 1 or 2 compressed
pages per physical page). The only advantage of zbud is a marginal
performance improvement that by no means justify the memory overhead.
Historically, zsmalloc had significantly worse latency than zbud and
z3fold but offered better memory savings. This is no longer the case as
shown by a simple recent analysis [1]. In a kernel build test on tmpfs in
a limited cgroup, zbud 2-3% less time than zsmalloc, but at the cost of
using ~32% more memory (1.5G vs 1.13G). The tradeoff does not make sense
for zbud in any practical scenario.
The only alleged advantage of zbud is not having the dependency on
CONFIG_MMU, but CONFIG_SWAP already depends on CONFIG_MMU anyway, and zbud
is only used by zswap.
Remove zbud after z3fold's removal, leaving zsmalloc as the one and only
zpool allocator. Leave the removal of the zpool API (and its associated
config options) to a followup cleanup after no more allocators show up.
Deprecating zbud for a few cycles before removing it was initially
proposed [2], like z3fold was marked as deprecated for 2 cycles [3].
However, Johannes rightfully pointed out that the 2 cycles is too short
for most downstream consumers, and z3fold was deprecated first only as a
courtesy anyway.
[1]https://lore.kernel.org/lkml/CAJD7tkbRF6od-2x_L8-A1QL3=2Ww13sCj4S3i4bNndqF+3+_Vg@mail.gmail.com/
[2]https://lore.kernel.org/lkml/Z5gdnSX5Lv-nfjQL@google.com/
[3]https://lore.kernel.org/lkml/20240904233343.933462-1-yosryahmed@google.com/
Link: https://lkml.kernel.org/r/20250129180633.3501650-3-yosry.ahmed@linux.dev
Signed-off-by: Yosry Ahmed <yosry.ahmed@linux.dev>
Reviewed-by: Shakeel Butt <shakeel.butt@linux.dev>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Nhat Pham <nphamcs@gmail.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Chengming Zhou <chengming.zhou@linux.dev>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: WANG Xuerui <kernel@xen0n.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
For now, it is time to remove -fno-jump-tables to enable jump table for
objtool if the compiler has -mannotate-tablejump, otherwise it is better
to remain -fno-jump-tables to keep compatibility with older compilers.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/20241217010905.13054-8-yangtiezhu@loongson.cn
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
|
|
__module_text_address() can be invoked within a RCU section, there is no
requirement to have preemption disabled.
Replace the preempt_disable() section around __module_text_address()
with RCU.
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: WANG Xuerui <kernel@xen0n.name>
Cc: linux-trace-kernel@vger.kernel.org
Cc: loongarch@lists.linux.dev
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20250108090457.512198-20-bigeasy@linutronix.de
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
|
|
__module_address() can be invoked within a RCU section, there is no
requirement to have preemption disabled.
Replace the preempt_disable() section around __module_address() with
RCU.
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: WANG Xuerui <kernel@xen0n.name>
Cc: loongarch@lists.linux.dev
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20250108090457.512198-19-bigeasy@linutronix.de
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
|
|
Physical address space is 48 bit on Loongson-3A5000 physical machine,
however it is 47 bit for VM on Loongson-3A5000 system. Size of physical
address space of VM is the same with the size of virtual user space (a
half) of physical machine.
Variable cpu_vabits represents user address space, kernel address space
is not included (user space and kernel space are both a half of total).
Here cpu_vabits, rather than cpu_vabits - 1, is to represent the size of
guest physical address space.
Also there is strict checking about page fault GPA address, inject error
if it is larger than maximum GPA address of VM.
Cc: stable@vger.kernel.org
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
On host, the HW guest CSR registers are lost after suspend and resume
operation. Since last_vcpu of boot CPU still records latest vCPU pointer
so that the guest CSR register skips to reload when boot CPU resumes and
vCPU is scheduled.
Here last_vcpu is cleared so that guest CSR registers will reload from
scheduled vCPU context after suspend and resume.
Cc: stable@vger.kernel.org
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
There is a newly added macro INT_AVEC with CSR ESTAT register, which is
bit 14 used for LoongArch AVEC support. AVEC interrupt status bit 14 is
supported with macro CSR_ESTAT_IS, so here replace the hard-coded value
0x1fff with macro CSR_ESTAT_IS so that the AVEC interrupt status is also
supported by KVM.
Cc: stable@vger.kernel.org
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
With ltp test case "testcases/bin/hugefork02", there is a dmesg error
report message such as:
kernel BUG at mm/hugetlb.c:5550!
Oops - BUG[#1]:
CPU: 0 UID: 0 PID: 1517 Comm: hugefork02 Not tainted 6.14.0-rc2+ #241
Hardware name: QEMU QEMU Virtual Machine, BIOS unknown 2/2/2022
pc 90000000004eaf1c ra 9000000000485538 tp 900000010edbc000 sp 900000010edbf940
a0 900000010edbfb00 a1 9000000108d20280 a2 00007fffe9474000 a3 00007ffff3474000
a4 0000000000000000 a5 0000000000000003 a6 00000000003cadd3 a7 0000000000000000
t0 0000000001ffffff t1 0000000001474000 t2 900000010ecd7900 t3 00007fffe9474000
t4 00007fffe9474000 t5 0000000000000040 t6 900000010edbfb00 t7 0000000000000001
t8 0000000000000005 u0 90000000004849d0 s9 900000010edbfa00 s0 9000000108d20280
s1 00007fffe9474000 s2 0000000002000000 s3 9000000108d20280 s4 9000000002b38b10
s5 900000010edbfb00 s6 00007ffff3474000 s7 0000000000000406 s8 900000010edbfa08
ra: 9000000000485538 unmap_vmas+0x130/0x218
ERA: 90000000004eaf1c __unmap_hugepage_range+0x6f4/0x7d0
PRMD: 00000004 (PPLV0 +PIE -PWE)
EUEN: 00000007 (+FPE +SXE +ASXE -BTE)
ECFG: 00071c1d (LIE=0,2-4,10-12 VS=7)
ESTAT: 000c0000 [BRK] (IS= ECode=12 EsubCode=0)
PRID: 0014c010 (Loongson-64bit, Loongson-3A5000)
Process hugefork02 (pid: 1517, threadinfo=00000000a670eaf4, task=000000007a95fc64)
Call Trace:
[<90000000004eaf1c>] __unmap_hugepage_range+0x6f4/0x7d0
[<9000000000485534>] unmap_vmas+0x12c/0x218
[<9000000000494068>] exit_mmap+0xe0/0x308
[<900000000025fdc4>] mmput+0x74/0x180
[<900000000026a284>] do_exit+0x294/0x898
[<900000000026aa30>] do_group_exit+0x30/0x98
[<900000000027bed4>] get_signal+0x83c/0x868
[<90000000002457b4>] arch_do_signal_or_restart+0x54/0xfa0
[<90000000015795e8>] irqentry_exit_to_user_mode+0xb8/0x138
[<90000000002572d0>] tlb_do_page_fault_1+0x114/0x1b4
The problem is that base address allocated from hugetlbfs is not aligned
with pmd size. Here add a checking for hugetlbfs and align base address
with pmd size. After this patch the test case "testcases/bin/hugefork02"
passes to run.
This is similar to the commit 7f24cbc9c4d42db8a3c8484d1 ("mm/mmap: teach
generic_get_unmapped_area{_topdown} to handle hugetlb mappings").
Cc: stable@vger.kernel.org # 6.13+
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The current max_pfn equals to zero. In this case, it causes user cannot
get some page information through /proc filesystem such as kpagecount.
The following message is displayed by stress-ng test suite with command
"stress-ng --verbose --physpage 1 -t 1".
# stress-ng --verbose --physpage 1 -t 1
stress-ng: error: [1691] physpage: cannot read page count for address 0x134ac000 in /proc/kpagecount, errno=22 (Invalid argument)
stress-ng: error: [1691] physpage: cannot read page count for address 0x7ffff207c3a8 in /proc/kpagecount, errno=22 (Invalid argument)
stress-ng: error: [1691] physpage: cannot read page count for address 0x134b0000 in /proc/kpagecount, errno=22 (Invalid argument)
...
After applying this patch, the kernel can pass the test.
# stress-ng --verbose --physpage 1 -t 1
stress-ng: debug: [1701] physpage: [1701] started (instance 0 on CPU 3)
stress-ng: debug: [1701] physpage: [1701] exited (instance 0 on CPU 3)
stress-ng: debug: [1700] physpage: [1701] terminated (success)
Cc: stable@vger.kernel.org # 6.8+
Fixes: ff6c3d81f2e8 ("NUMA: optimize detection of memory with no node id assigned by firmware")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
When CONFIG_RANDOM_KMALLOC_CACHES or other randomization infrastructrue
enabled, the idle_task's stack may different between the booting kernel
and target kernel. So when resuming from hibernation, an ACTION_BOOT_CPU
IPI wakeup the idle instruction in arch_cpu_idle_dead() and jump to the
interrupt handler. But since the stack pointer is changed, the interrupt
handler cannot restore correct context.
So rename the current arch_cpu_idle_dead() to idle_play_dead(), make it
as the default version of play_dead(), and the new arch_cpu_idle_dead()
call play_dead() directly. For hibernation, implement an arch-specific
hibernate_resume_nonboot_cpu_disable() to use the polling version (idle
instruction is replace by nop, and irq is disabled) of play_dead(), i.e.
poll_play_dead(), to avoid IPI handler corrupting the idle_task's stack
when resuming from hibernation.
This solution is a little similar to commit 406f992e4a372dafbe3c ("x86 /
hibernate: Use hlt_play_dead() when resuming from hibernation").
Cc: stable@vger.kernel.org
Tested-by: Erpeng Xu <xuerpeng@uniontech.com>
Tested-by: Yuli Wang <wangyuli@uniontech.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
In LoongArch, get_numa_distances_cnt() isn't in use, resulting in a
compiler warning.
Fix follow errors with clang-18 when W=1e:
arch/loongarch/kernel/acpi.c:259:28: error: unused function 'get_numa_distances_cnt' [-Werror,-Wunused-function]
259 | static inline unsigned int get_numa_distances_cnt(struct acpi_table_slit *slit)
| ^~~~~~~~~~~~~~~~~~~~~~
1 error generated.
Link: https://lore.kernel.org/all/Z7bHPVUH4lAezk0E@kernel.org/
Signed-off-by: Yuli Wang <wangyuli@uniontech.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
When compiling on LoongArch, there exists the following objtool warning
in arch/loongarch/kernel/machine_kexec.o:
kexec_reboot() falls through to next function crash_shutdown_secondary()
Avoid using unreachable() as it can (and will in the absence of UBSAN)
generate fall-through code. Use BUG() so we get a "break BRK_BUG" trap
(with unreachable annotation).
Cc: stable@vger.kernel.org # 6.12+
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
In order to fix a bug, arm64 needs to be told the size of the huge page
for which the huge_pte is being cleared in huge_ptep_get_and_clear().
Provide for this by adding an `unsigned long sz` parameter to the
function. This follows the same pattern as huge_pte_clear() and
set_huge_pte_at().
This commit makes the required interface modifications to the core mm as
well as all arches that implement this function (arm64, loongarch, mips,
parisc, powerpc, riscv, s390, sparc). The actual arm64 bug will be fixed
in a separate commit.
Cc: stable@vger.kernel.org
Fixes: 66b3923a1a0f ("arm64: hugetlb: add support for PTE contiguous bit")
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com> # riscv
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> # s390
Link: https://lore.kernel.org/r/20250226120656.2400136-2-ryan.roberts@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Remove kvm_arch_sync_events() now that x86 no longer uses it (no other
arch has ever used it).
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Acked-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Message-ID: <20250224235542.2562848-8-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Since 2002 (change "Replace BKL for chain locking with sysvfs-private
rwlock") the sysv filesystem was doing IO under a rwlock in its
get_block() function (yes, a non-sleepable lock hold over a function
used to read inode metadata for all reads and writes). Nobody noticed
until syzbot in 2023 [1]. This shows nobody is using the filesystem.
Just drop it.
[1] https://lore.kernel.org/all/0000000000000ccf9a05ee84f5b0@google.com/
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20250220163940.10155-2-jack@suse.cz
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
The generic storage implementation provides the same features as the
custom one. However it can be shared between architectures, making
maintenance easier.
Co-developed-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250204-vdso-store-rng-v3-10-13a4669dfc8c@linutronix.de
|
|
As the Makefile is included into other Makefiles it can not be used to
define objects to be built from the current source directory.
However the generic datastore will introduce such a local source file.
Rename the included Makefile so it is clear how it is to be used and to
make room for a regular Makefile in lib/vdso/.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250204-vdso-store-rng-v3-4-13a4669dfc8c@linutronix.de
|
|
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/a5b1b53813a15a73afdfff6fbb4c9064fa582be1.1738746821.git.namcao@linutronix.de
|
|
PRMD register is only meaningful on the beginning stage of exception
entry, and it is overwritten with nested irq or exception.
When CPU runs in VM mode, interrupt need be enabled on host. And the
mode for host had better be kernel mode rather than random or user mode.
When VM is running, the running mode with top command comes from CRMD
register, and running mode should be kernel mode since kernel function
is executing with perf command. It needs be consistent with both top and
perf command.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Cache attribute comes from GPA->HPA secondary mmu page table and is
configured when kvm is enabled. It is the same for all VMs, so remove
duplicated cache attribute setting on vCPU context switch.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
This is typo issue and misusage about GCFG feature macro. The code
is wrong, only that it does not cause obvious problem since GCFG is
set again on vCPU context switch.
Fixes: 0d0df3c99d4f ("LoongArch: KVM: Implement kvm hardware enable, disable interface")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Commit 69e3a6aa6be2 ("LoongArch: Add checksum optimization for 64-bit
system") would cause an undefined shift and an out-of-bounds read.
Commit 8bd795fedb84 ("arm64: csum: Fix OoB access in IP checksum code
for negative lengths") fixes the same issue on ARM64.
Fixes: 69e3a6aa6be2 ("LoongArch: Add checksum optimization for 64-bit system")
Co-developed-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Yuli Wang <wangyuli@uniontech.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The notifier hook mechanism in proc and cpuinfo is actually unnecessary
for LoongArch because it's not used anywhere.
It was originally added to the MIPS code in commit d6d3c9afaab4 ("MIPS:
MT: proc: Add support for printing VPE and TC ids"), and LoongArch then
inherited it.
But as the kernel code stands now, this notifier hook mechanism doesn't
really make sense for either LoongArch or MIPS.
In addition, the seq_file forward declaration needs to be moved to its
proper place, as only the show_ipi_list() function in smp.c requires it.
Co-developed-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Yuli Wang <wangyuli@uniontech.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Remove hard-coded strings by using the str_yes_no() helper function.
Similar to commit c4a0a4a45a45 ("MIPS: kernel: proc: Use str_yes_no()
helper function").
Co-developed-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Yuli Wang <wangyuli@uniontech.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Now kernel_page_present() always return true for KPRANGE/XKPRANGE
addresses, this isn't correct because hibernation (ACPI S4) use it
to distinguish whether a page is saveable. If all KPRANGE/XKPRANGE
addresses are considered as saveable, then reserved memory such as
EFI_RUNTIME_SERVICES_CODE / EFI_RUNTIME_SERVICES_DATA will also be
saved and restored.
Fix this by returning true only if the KPRANGE/XKPRANGE address is in
memblock.memory.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
LoongArch re-enables interrupts on its idle routine and performs a
TIF_NEED_RESCHED check afterwards before putting the CPU to sleep.
The IRQs firing between the check and the idle instruction may set the
TIF_NEED_RESCHED flag. In order to deal with such a race, IRQs
interrupting __arch_cpu_idle() rollback their return address to the
beginning of __arch_cpu_idle() so that TIF_NEED_RESCHED is checked
again before going back to sleep.
However idle IRQs can also queue timers that may require a tick
reprogramming through a new generic idle loop iteration but those timers
would go unnoticed here because __arch_cpu_idle() only checks
TIF_NEED_RESCHED. It doesn't check for pending timers.
Fix this with fast-forwarding idle IRQs return address to the end of the
idle routine instead of the beginning, so that the generic idle loop can
handle both TIF_NEED_RESCHED and pending timers.
Fixes: 0603839b18f4 ("LoongArch: Add exception/interrupt handling")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The 2k1000 reference boards do not have a Rohm DAC on them as far as I
can tell, and they certainly do not have a dh2228fv, as this device does
not actually exist! Remove the dac nodes from the devicetrees as it is
not acceptable to pretend to have a device on a board in order to bind
the spidev driver in Linux.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240717-preacher-sandal-2aeffa322b9f@spud
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Following the standardization on crc32c() as the lib entry point for the
Castagnoli CRC32 instead of the previous mix of crc32c(), crc32c_le(),
and __crc32c_le(), make the same change to the underlying base and arch
functions that implement it.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20250208024911.14936-7-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch updates from Huacai Chen:
- Migrate to the generic rule for built-in DTB
- Disable FIX_EARLYCON_MEM when ARCH_IOREMAP is enabled
- Derive timer max_delta from PRCFG1's timer_bits
- Correct the cacheinfo sharing information
- Add pgprot_nx() implementation
- Add debugfs entries to switch SFB/TSO state
- Change the maximum number of watchpoints
- Some bug fixes and other small changes
* tag 'loongarch-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: Extend the maximum number of watchpoints
LoongArch: Change 8 to 14 for LOONGARCH_MAX_{BRP,WRP}
LoongArch: Add debugfs entries to switch SFB/TSO state
LoongArch: Fix warnings during S3 suspend
LoongArch: Adjust SETUP_SLEEP and SETUP_WAKEUP
LoongArch: Refactor bug_handler() implementation
LoongArch: Add pgprot_nx() implementation
LoongArch: Correct the __switch_to() prototype in comments
LoongArch: Correct the cacheinfo sharing information
LoongArch: Derive timer max_delta from PRCFG1's timer_bits
LoongArch: Disable FIX_EARLYCON_MEM when ARCH_IOREMAP is enabled
LoongArch: Migrate to the generic rule for built-in DTB
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
"The various patchsets are summarized below. Plus of course many
indivudual patches which are described in their changelogs.
- "Allocate and free frozen pages" from Matthew Wilcox reorganizes
the page allocator so we end up with the ability to allocate and
free zero-refcount pages. So that callers (ie, slab) can avoid a
refcount inc & dec
- "Support large folios for tmpfs" from Baolin Wang teaches tmpfs to
use large folios other than PMD-sized ones
- "Fix mm/rodata_test" from Petr Tesarik performs some maintenance
and fixes for this small built-in kernel selftest
- "mas_anode_descend() related cleanup" from Wei Yang tidies up part
of the mapletree code
- "mm: fix format issues and param types" from Keren Sun implements a
few minor code cleanups
- "simplify split calculation" from Wei Yang provides a few fixes and
a test for the mapletree code
- "mm/vma: make more mmap logic userland testable" from Lorenzo
Stoakes continues the work of moving vma-related code into the
(relatively) new mm/vma.c
- "mm/page_alloc: gfp flags cleanups for alloc_contig_*()" from David
Hildenbrand cleans up and rationalizes handling of gfp flags in the
page allocator
- "readahead: Reintroduce fix for improper RA window sizing" from Jan
Kara is a second attempt at fixing a readahead window sizing issue.
It should reduce the amount of unnecessary reading
- "synchronously scan and reclaim empty user PTE pages" from Qi Zheng
addresses an issue where "huge" amounts of pte pagetables are
accumulated:
https://lore.kernel.org/lkml/cover.1718267194.git.zhengqi.arch@bytedance.com/
Qi's series addresses this windup by synchronously freeing PTE
memory within the context of madvise(MADV_DONTNEED)
- "selftest/mm: Remove warnings found by adding compiler flags" from
Muhammad Usama Anjum fixes some build warnings in the selftests
code when optional compiler warnings are enabled
- "mm: don't use __GFP_HARDWALL when migrating remote pages" from
David Hildenbrand tightens the allocator's observance of
__GFP_HARDWALL
- "pkeys kselftests improvements" from Kevin Brodsky implements
various fixes and cleanups in the MM selftests code, mainly
pertaining to the pkeys tests
- "mm/damon: add sample modules" from SeongJae Park enhances DAMON to
estimate application working set size
- "memcg/hugetlb: Rework memcg hugetlb charging" from Joshua Hahn
provides some cleanups to memcg's hugetlb charging logic
- "mm/swap_cgroup: remove global swap cgroup lock" from Kairui Song
removes the global swap cgroup lock. A speedup of 10% for a
tmpfs-based kernel build was demonstrated
- "zram: split page type read/write handling" from Sergey Senozhatsky
has several fixes and cleaups for zram in the area of
zram_write_page(). A watchdog softlockup warning was eliminated
- "move pagetable_*_dtor() to __tlb_remove_table()" from Kevin
Brodsky cleans up the pagetable destructor implementations. A rare
use-after-free race is fixed
- "mm/debug: introduce and use VM_WARN_ON_VMG()" from Lorenzo Stoakes
simplifies and cleans up the debugging code in the VMA merging
logic
- "Account page tables at all levels" from Kevin Brodsky cleans up
and regularizes the pagetable ctor/dtor handling. This results in
improvements in accounting accuracy
- "mm/damon: replace most damon_callback usages in sysfs with new
core functions" from SeongJae Park cleans up and generalizes
DAMON's sysfs file interface logic
- "mm/damon: enable page level properties based monitoring" from
SeongJae Park increases the amount of information which is
presented in response to DAMOS actions
- "mm/damon: remove DAMON debugfs interface" from SeongJae Park
removes DAMON's long-deprecated debugfs interfaces. Thus the
migration to sysfs is completed
- "mm/hugetlb: Refactor hugetlb allocation resv accounting" from
Peter Xu cleans up and generalizes the hugetlb reservation
accounting
- "mm: alloc_pages_bulk: small API refactor" from Luiz Capitulino
removes a never-used feature of the alloc_pages_bulk() interface
- "mm/damon: extend DAMOS filters for inclusion" from SeongJae Park
extends DAMOS filters to support not only exclusion (rejecting),
but also inclusion (allowing) behavior
- "Add zpdesc memory descriptor for zswap.zpool" from Alex Shi
introduces a new memory descriptor for zswap.zpool that currently
overlaps with struct page for now. This is part of the effort to
reduce the size of struct page and to enable dynamic allocation of
memory descriptors
- "mm, swap: rework of swap allocator locks" from Kairui Song redoes
and simplifies the swap allocator locking. A speedup of 400% was
demonstrated for one workload. As was a 35% reduction for kernel
build time with swap-on-zram
- "mm: update mips to use do_mmap(), make mmap_region() internal"
from Lorenzo Stoakes reworks MIPS's use of mmap_region() so that
mmap_region() can be made MM-internal
- "mm/mglru: performance optimizations" from Yu Zhao fixes a few
MGLRU regressions and otherwise improves MGLRU performance
- "Docs/mm/damon: add tuning guide and misc updates" from SeongJae
Park updates DAMON documentation
- "Cleanup for memfd_create()" from Isaac Manjarres does that thing
- "mm: hugetlb+THP folio and migration cleanups" from David
Hildenbrand provides various cleanups in the areas of hugetlb
folios, THP folios and migration
- "Uncached buffered IO" from Jens Axboe implements the new
RWF_DONTCACHE flag which provides synchronous dropbehind for
pagecache reading and writing. To permite userspace to address
issues with massive buildup of useless pagecache when
reading/writing fast devices
- "selftests/mm: virtual_address_range: Reduce memory" from Thomas
Weißschuh fixes and optimizes some of the MM selftests"
* tag 'mm-stable-2025-01-26-14-59' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (321 commits)
mm/compaction: fix UBSAN shift-out-of-bounds warning
s390/mm: add missing ctor/dtor on page table upgrade
kasan: sw_tags: use str_on_off() helper in kasan_init_sw_tags()
tools: add VM_WARN_ON_VMG definition
mm/damon/core: use str_high_low() helper in damos_wmark_wait_us()
seqlock: add missing parameter documentation for raw_seqcount_try_begin()
mm/page-writeback: consolidate wb_thresh bumping logic into __wb_calc_thresh
mm/page_alloc: remove the incorrect and misleading comment
zram: remove zcomp_stream_put() from write_incompressible_page()
mm: separate move/undo parts from migrate_pages_batch()
mm/kfence: use str_write_read() helper in get_access_type()
selftests/mm/mkdirty: fix memory leak in test_uffdio_copy()
kasan: hw_tags: Use str_on_off() helper in kasan_init_hw_tags()
selftests/mm: virtual_address_range: avoid reading from VM_IO mappings
selftests/mm: vm_util: split up /proc/self/smaps parsing
selftests/mm: virtual_address_range: unmap chunks after validation
selftests/mm: virtual_address_range: mmap() without PROT_WRITE
selftests/memfd/memfd_test: fix possible NULL pointer dereference
mm: add FGP_DONTCACHE folio creation flag
mm: call filemap_fdatawrite_range_kick() after IOCB_DONTCACHE issue
...
|
|
The maximum number of load/store watchpoints and fetch instruction
watchpoints is 14 each according to LoongArch Reference Manual, so
extend the maximum number of watchpoints from 8 to 14 for ptrace.
By the way, just simply change 8 to 14 for the definition in struct
user_watch_state at the beginning, but it may corrupt uapi, then add
a new struct user_watch_state_v2 directly.
As far as I can tell, the only users for this struct in the userspace
are GDB and LLDB, there are no any problems of software compatibility
between the application and kernel according to the analysis.
The compatibility problem has been considered while developing and
testing. When the applications in the userspace get watchpoint state,
the length will be specified which is no bigger than the sizeof struct
user_watch_state or user_watch_state_v2, the actual length is assigned
as the minimal value of the application and kernel in the generic code
of ptrace:
kernel/ptrace.c: ptrace_regset():
kiov->iov_len = min(kiov->iov_len,
(__kernel_size_t) (regset->n * regset->size));
if (req == PTRACE_GETREGSET)
return copy_regset_to_user(task, view, regset_no, 0,
kiov->iov_len, kiov->iov_base);
else
return copy_regset_from_user(task, view, regset_no, 0,
kiov->iov_len, kiov->iov_base);
For example, there are four kind of combinations, all of them work well.
(1) "older kernel + older gdb", the actual length is 8+(8+8+4+4)*8=200;
(2) "newer kernel + newer gdb", the actual length is 8+(8+8+4+4)*14=344;
(3) "older kernel + newer gdb", the actual length is 8+(8+8+4+4)*8=200;
(4) "newer kernel + older gdb", the actual length is 8+(8+8+4+4)*8=200.
Link: https://loongson.github.io/LoongArch-Documentation/LoongArch-Vol1-EN.html#control-and-status-registers-related-to-watchpoints
Cc: stable@vger.kernel.org
Fixes: 1a69f7a161a7 ("LoongArch: ptrace: Expose hardware breakpoints to debuggers")
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
