| Age | Commit message (Collapse) | Author |
|---|
|
arch/mips/generic/init.c provides an implementation of the
plat_fdt_relocated() function, but doesn't include the asm/bootinfo.h
header which declares it. This leads to a warning from sparse:
arch/mips/generic/init.c:94:13: warning: symbol 'plat_fdt_relocated' was
not declared. Should it be static?
Fix this by including asm/bootinfo.h to get the declaration of
plat_fdt_relocated(). We also #ifdef our definition of
plat_fdt_relocated() such that it is only provided when
CONFIG_RELOCATABLE is set, matching the header & avoiding the redundant
function for non-relocatable kernels.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17166/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Besides eliminating lots of duplication this also allows allocations with
the DMA_ATTR_NON_CONSISTENT to use the CMA allocator.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17181/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Create a defconfig for the Omega2+ that reaches userspace and
allows use of the USB port.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: john@phrozen.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17138/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The Onion Omega2+ is an MT7688A based board that has 128MB RAM and
multiple peripherals.
The MT7688A is pin compatible with the MT7628A, although the former
supports a 1T1R antenna whereas the MT7628A supports a 2R2T antenna.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: john@phrozen.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17137/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Enabled supported drivers, including:
- USB PHY
- EHCI
- UART
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: john@phrozen.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17135/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The VoCore2 board is a low cost MT7628A based board with 128MB RAM, 16MB
flash and multiple external peripherals.
This initial DTS provides enough support to get to userland and use the USB
port.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: john@phrozen.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17134/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The MT7628A is the successor to the MT7620 and pin compatible with the
MT7688A, although the latter supports only a 1T1R antenna rather than
a 2T2R antenna.
This commit adds support for the following features:
- UART
- USB PHY
- EHCI
- Interrupt controller
- System controller
- Memory controller
- Reset controller
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: john@phrozen.org
Cc: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/17133/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This introduces threaded carddetect irqs for the db1200/db1300 boards.
Main benefit is that the broken insertion/ejection interrupt pairs
can now be better supported and debounced in software.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15287/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
No advanced MIPS features for Alchemy.
This patch shaves additional 43kB off the DB1300 kernel
(~0.5% size reduction).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15286/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Prints the devboard name in cpuinfo "machine" line.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15285/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
GCC-7 complains about a boolean value being used with an arithmetic
AND:
arch/mips/math-emu/cp1emu.c: In function 'cop1Emulate':
arch/mips/math-emu/cp1emu.c:838:14: warning: '~' on a boolean expression [-Wbool-operation]
fpr = (x) & ~(cop1_64bit(xcp) == 0); \
^
arch/mips/math-emu/cp1emu.c:1068:3: note: in expansion of macro 'DITOREG'
DITOREG(dval, MIPSInst_RT(ir));
^~~~~~~
arch/mips/math-emu/cp1emu.c:838:14: note: did you mean to use logical not?
fpr = (x) & ~(cop1_64bit(xcp) == 0); \
Since cop1_64bit() returns and int, just flip the LSB.
Suggested-by: Maciej W. Rozycki <macro@imgtec.com>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Reviewed-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17058/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add devicetree nodes for the DM9000 and the ethernet power regulator.
Additionally, add a new pinctrl node for the ethernet chip's pins.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16752/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Update the Ci20's defconfig to enable the JZ4780's GPIO driver.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16751/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Move the NI 169445 board flattened image tree source into its own file
which is concatenated into the final image tree source used to build the
flattened image tree. Separating boards into different files will help
us to avoid conflicts as boards are added.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Nathan Sullivan <nathan.sullivan@ni.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16940/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Move the Boston board flattened image tree source into its own file
which is concatenated into the final image tree source used to build the
flattened image tree. Separating boards into different files will help
us to avoid conflicts as boards are added.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16939/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
In preparation for splitting arch/mips/generic/vmlinux.its.S into
multiple files such that it doesn't become a conflict magnet as boards
are added, allow platforms to specify a list of image tree source files
which will be concatenated to form the final source used to build the
image tree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16938/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Define Cavium Octeon as a CPU that has support for mips32r1, mips32r2 and
mips64r1. This will affect show_cpuinfo() that will now correctly expose
mips32r1, mips32r2 and mips64r1 as supported ISAs.
Signed-off-by: Petar Jovanovic <petar.jovanovic@rt-rk.com>
Reviewed-by: Maciej W. Rozycki <macro@imgtec.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: petar.jovanovic@imgtec.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15749/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Based on discussion with Linus remove the impossible to reach code
rather than replacing it with a BUG().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/20170718140651.15973-4-ebiederm@xmission.com
|
|
Support the National Instruments 169445 board.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16782/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16785/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
When the upstream kernel pistachio_defconfig is built & tested on the
ci40 platform the current lack of these options leads to essentially
false failures when the RFS fails to mount.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: James Hartley <james.hartley@sondrel.com>
Cc: Ionela Voinescu <ionela.voinescu@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16763/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit a7be6e5a7f8d ("mm: drop useless local parameters of
__register_one_node()") removes the last user of parent_node().
The parent_node() macros in both IP27 and Loongson64 are unnecessary.
Remove it for cleanup.
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16873/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Compile USB driver statically, enable EDAC driver, and remove
deprecated options.
Signed-off-by: Steven J. Hill <steven.hill@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16795/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 1a3d59579b9f ("MIPS: Tidy up FPU context switching") removed
usage of ST_OFF, leaving it behind as dead code. Commit 828d1e4e9865
("MIPS: Remove dead define of ST_OFF") then removed the definition of
ST_OFF from r4k_switch.S as a cleanup. However the unused definition of
ST_OFF has been left behind in r2300_switch.S. Remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16239/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Move _save_fp(), _restore_fp() & _init_fpu() out of r2300_switch.S &
into r2300_fpu.S. This logically places all FP-related asm code into
r2300_fpu.S & provides consistency with R4K after the preceding commit.
Besides cleaning up this will be useful for later patches which disable
FP support.
[ralf@linux-mips.org: Fixed build issues reported by Arnd Bergmann
<arnd@arndb.de>]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16238/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Move _save_fp(), _restore_fp(), _save_msa(), _restore_msa(),
_init_msa_upper() & _init_fpu() out of r4k_switch.S & into r4k_fpu.S.
This allows us to clean up the way in which Octeon includes the default
r4k implementations of these FP functions despite replacing resume(),
and makes CONFIG_R4K_FPU more straightforwardly represent all
configurations that have an R4K-style FPU, including Octeon.
Besides cleaning up this will be useful for later patches which disable
FP support.
[ralf@linux-mips.org: Fixed build issues reported by Arnd Bergmann
<arnd@arndb.de>]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16237/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The kernel contains a small amount of incomplete code aimed at
supporting old R6000 CPUs. This is:
- Unused, as no machine selects CONFIG_SYS_HAS_CPU_R6000.
- Broken, since there are glaring errors such as r6000_fpu.S moving
the FCSR register to t1, then ignoring it & instead saving t0 into
struct sigcontext...
- A maintenance headache, since it's code that nobody can test which
nevertheless imposes constraints on code which it shares with other
machines.
Remove this incomplete & broken R6000 CPU support in order to clean up
and in preparation for changes which will no longer need to consider
dragging the pretense of R6000 support along with them.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16236/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The r2_decoder_tables are never modified. They are arrays of constant
values and as such should be declared const.
This change saves 256 bytes of kernel text, and 128 bytes of kernel data
(384 bytes total) on a 32r6el_defconfig (with SMP disabled)
Before:
text data bss dec hex filename
5576221 1080804 267040 6924065 69a721 vmlinux
After:
text data bss dec hex filename
5575965 1080676 267040 6923681 69a5a1 vmlinux
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15289/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
smp_ops providers do not modify their ops structures, so they should be
made const for robustness. Since currently the MIPS kernel is not mapped
with memory protection, this does not in itself provide any security
benefit, but it still makes sense to make this change.
There are also slight code size efficincies from the structure being
made read-only, saving 128 bytes of kernel text on a
pistachio_defconfig.
Before:
text data bss dec hex filename
7187239 1772752 470224 9430215 8fe4c7 vmlinux
After:
text data bss dec hex filename
7187111 1772752 470224 9430087 8fe447 vmlinux
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Doug Ledford <dledford@redhat.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Joe Perches <joe@perches.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Steven J. Hill <steven.hill@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16784/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove options which do not exist anymore:
- CPU_FREQ_DEBUG is gone since commit 2d06d8c49afd ("[CPUFREQ] use
dynamic debug instead of custom infrastructure").
- ECONET is gone since commit 349f29d841db ("econet: remove ancient bug
ridden protocol");
- IPDDP_DECAP is gone since commit 9b5645b51384 ("appletalk: remove
"config IPDDP_DECAP"");
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16770/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16783/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
struct call_single_data is used in IPIs to transfer information between
CPUs. Its size is bigger than sizeof(unsigned long) and less than
cache line size. Currently it is not allocated with any explicit alignment
requirements. This makes it possible for allocated call_single_data to
cross two cache lines, which results in double the number of the cache lines
that need to be transferred among CPUs.
This can be fixed by requiring call_single_data to be aligned with the
size of call_single_data. Currently the size of call_single_data is the
power of 2. If we add new fields to call_single_data, we may need to
add padding to make sure the size of new definition is the power of 2
as well.
Fortunately, this is enforced by GCC, which will report bad sizes.
To set alignment requirements of call_single_data to the size of
call_single_data, a struct definition and a typedef is used.
To test the effect of the patch, I used the vm-scalability multiple
thread swap test case (swap-w-seq-mt). The test will create multiple
threads and each thread will eat memory until all RAM and part of swap
is used, so that huge number of IPIs are triggered when unmapping
memory. In the test, the throughput of memory writing improves ~5%
compared with misaligned call_single_data, because of faster IPIs.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Huang, Ying <ying.huang@intel.com>
[ Add call_single_data_t and align with size of call_single_data. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/87bmnqd6lz.fsf@yhuang-mobile.sh.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There is code duplicated over all architecture's headers for
futex_atomic_op_inuser. Namely op decoding, access_ok check for uaddr,
and comparison of the result.
Remove this duplication and leave up to the arches only the needed
assembly which is now in arch_futex_atomic_op_inuser.
This effectively distributes the Will Deacon's arm64 fix for undefined
behaviour reported by UBSAN to all architectures. The fix was done in
commit 5f16a046f8e1 (arm64: futex: Fix undefined behaviour with
FUTEX_OP_OPARG_SHIFT usage). Look there for an example dump.
And as suggested by Thomas, check for negative oparg too, because it was
also reported to cause undefined behaviour report.
Note that s390 removed access_ok check in d12a29703 ("s390/uaccess:
remove pointless access_ok() checks") as access_ok there returns true.
We introduce it back to the helper for the sake of simplicity (it gets
optimized away anyway).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> [s390]
Acked-by: Chris Metcalf <cmetcalf@mellanox.com> [for tile]
Reviewed-by: Darren Hart (VMware) <dvhart@infradead.org>
Reviewed-by: Will Deacon <will.deacon@arm.com> [core/arm64]
Cc: linux-mips@linux-mips.org
Cc: Rich Felker <dalias@libc.org>
Cc: linux-ia64@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: peterz@infradead.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: sparclinux@vger.kernel.org
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux-s390@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: linux-hexagon@vger.kernel.org
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-xtensa@linux-xtensa.org
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: openrisc@lists.librecores.org
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Stafford Horne <shorne@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Richard Henderson <rth@twiddle.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-parisc@vger.kernel.org
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: linux-alpha@vger.kernel.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: "David S. Miller" <davem@davemloft.net>
Link: http://lkml.kernel.org/r/20170824073105.3901-1-jslaby@suse.cz
|
|
There is a missing break causing a fall-through and setting
ctx.use_bbit_insns to the wrong value. Fix this by adding the
missing break.
Detected with cppcheck:
"Variable 'ctx.use_bbit_insns' is reassigned a value before the old
one has been used. 'break;' missing?"
Fixes: 8d8d18c3283f ("MIPS,bpf: Fix using smp_processor_id() in preemptible splat.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code looks a little cleaner if we replace BPF_OP(insn->code) with
the local variable bpf_op. Caching the value this way also saves 300
bytes (about 1%) in the code size of the JIT.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the kernel is configured with preemption enabled we were getting
warning stack traces for use of current_cpu_type().
Fix by moving the test between preempt_disable()/preempt_enable() and
caching the results of the CPU type tests for use during code
generation.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no dependency between the two, so remove the dependency in
Kconfig files.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
In a recent discussion Maciej Rozycki reported that this case is
impossible.
Handle the impossible case by just returning instead of trying to
handle it. This makes static analysis simpler as it means nothing
needs to consider the impossible case after the return statement.
As the code no longer has to deal with this case remove FPE_FIXME from
the mips siginfo.h
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/20170718140651.15973-4-ebiederm@xmission.com
Ref: ea1b75cf9138 ("signal/mips: Document a conflict with SI_USER with SIGFPE")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
|
|
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes:
- compressed boot: Ignore a generated .c file
- VDSO: Fix a register clobber list
- DECstation: Fix an int-handler.S CPU_DADDI_WORKAROUNDS regression
- Octeon: Fix recent cleanups that cleaned away a bit too much thus
breaking the arch side of the EDAC and USB drivers.
- uasm: Fix duplicate const in "const struct foo const bar[]" which
GCC 7.1 no longer accepts.
- Fix race on setting and getting cpu_online_mask
- Fix preemption issue. To do so cleanly introduce macro to get the
size of L3 cache line.
- Revert include cleanup that sometimes results in build error
- MicroMIPS uses bit 0 of the PC to indicate microMIPS mode. Make
sure this bit is set for kernel entry as well.
- Prevent configuring the kernel for both microMIPS and MT. There are
no such CPUs currently and thus the combination is unsupported and
results in build errors.
This has been sitting in linux-next for a few days and has survived
automated testing by Imagination's test farm. No known regressions
pending except a number of issues that crept up due to lots of people
switching to GCC 7.1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Set ISA bit in entry-y for microMIPS kernels
MIPS: Prevent building MT support for microMIPS kernels
MIPS: PCI: Fix smp_processor_id() in preemptible
MIPS: Introduce cpu_tcache_line_size
MIPS: DEC: Fix an int-handler.S CPU_DADDI_WORKAROUNDS regression
MIPS: VDSO: Fix clobber lists in fallback code paths
Revert "MIPS: Don't unnecessarily include kmalloc.h into <asm/cache.h>."
MIPS: OCTEON: Fix USB platform code breakage.
MIPS: Octeon: Fix broken EDAC driver.
MIPS: gitignore: ignore generated .c files
MIPS: Fix race on setting and getting cpu_online_mask
MIPS: mm: remove duplicate "const" qualifier on insn_table
|
|
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Peter Pan <peterpandong@micron.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Han Xu <han.xu@nxp.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-By: Harvey Hunt <harveyhuntnexus@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
|
|
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"The pull requests are getting smaller, that's progress I suppose :-)
1) Fix infinite loop in CIPSO option parsing, from Yujuan Qi.
2) Fix remote checksum handling in VXLAN and GUE tunneling drivers,
from Koichiro Den.
3) Missing u64_stats_init() calls in several drivers, from Florian
Fainelli.
4) TCP can set the congestion window to an invalid ssthresh value
after congestion window reductions, from Yuchung Cheng.
5) Fix BPF jit branch generation on s390, from Daniel Borkmann.
6) Correct MIPS ebpf JIT merge, from David Daney.
7) Correct byte order test in BPF test_verifier.c, from Daniel
Borkmann.
8) Fix various crashes and leaks in ASIX driver, from Dean Jenkins.
9) Handle SCTP checksums properly in mlx4 driver, from Davide
Caratti.
10) We can potentially enter tcp_connect() with a cached route
already, due to fastopen, so we have to explicitly invalidate it.
11) skb_warn_bad_offload() can bark in legitimate situations, fix from
Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
net: avoid skb_warn_bad_offload false positives on UFO
qmi_wwan: fix NULL deref on disconnect
ppp: fix xmit recursion detection on ppp channels
rds: Reintroduce statistics counting
tcp: fastopen: tcp_connect() must refresh the route
net: sched: set xt_tgchk_param par.net properly in ipt_init_target
net: dsa: mediatek: add adjust link support for user ports
net/mlx4_en: don't set CHECKSUM_COMPLETE on SCTP packets
qed: Fix a memory allocation failure test in 'qed_mcp_cmd_init()'
hysdn: fix to a race condition in put_log_buffer
s390/qeth: fix L3 next-hop in xmit qeth hdr
asix: Fix small memory leak in ax88772_unbind()
asix: Ensure asix_rx_fixup_info members are all reset
asix: Add rx->ax_skb = NULL after usbnet_skb_return()
bpf: fix selftest/bpf/test_pkt_md_access on s390x
netvsc: fix race on sub channel creation
bpf: fix byte order test in test_verifier
xgene: Always get clk source, but ignore if it's missing for SGMII ports
MIPS: Add missing file for eBPF JIT.
bpf, s390: fix build for libbpf and selftest suite
...
|
|
When building a kernel for the microMIPS ISA, ensure that the ISA bit
(ie. bit 0) in the entry address is set. Otherwise we may include an
entry address in images which bootloaders will jump to as MIPS32 code.
I originally tried using "objdump -f" to obtain the entry address, which
works for microMIPS but it always outputs a 32 bit address for a 32 bit
ELF whilst nm will sign extend to 64 bit. That matters for systems where
we might want to run a MIPS32 kernel on a MIPS64 CPU & load it with a
MIPS64 bootloader, which would then jump to a non-canonical
(non-sign-extended) address.
This works in all cases as it only changes the behaviour for microMIPS
kernels, but isn't the prettiest solution. A possible alternative would
be to write a custom tool to just extract, sign extend & print the entry
point of an ELF executable. I'm open to feedback if that would be
preferred.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16950/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
We don't currently support the MT ASE for microMIPS kernels, and there
are no CPUs currently in existence that use both. They can however both
be enabled in Kconfig, resulting in build failures such as:
AS arch/mips/kernel/cps-vec.o
arch/mips/kernel/cps-vec.S: Assembler messages:
arch/mips/kernel/cps-vec.S:242: Warning: the 32-bit microMIPS architecture does not support the `mt' extension
arch/mips/kernel/cps-vec.S:276: Error: unrecognized opcode `mttc0 $13,$2,2'
arch/mips/kernel/cps-vec.S:282: Error: unrecognized opcode `mttc0 $8,$1,2'
arch/mips/kernel/cps-vec.S:285: Error: unrecognized opcode `mttc0 $0,$2,1'
...
Fix this by preventing MT from being enabled when targeting microMIPS.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16951/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
If a vcpu exits due to request a user mode spinlock, then
the spinlock-holder may be preempted in user mode or kernel mode.
(Note that not all architectures trap spin loops in user mode,
only AMD x86 and ARM/ARM64 currently do).
But if a vcpu exits in kernel mode, then the holder must be
preempted in kernel mode, so we should choose a vcpu in kernel mode
as a more likely candidate for the lock holder.
This introduces kvm_arch_vcpu_in_kernel() to decide whether the
vcpu is in kernel-mode when it's preempted. kvm_vcpu_on_spin's
new argument says the same of the spinning VCPU.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Commit 1c3c5eab1715 ("sched/core: Enable might_sleep() and
smp_processor_id() checks early") enables checks for might_sleep() and
smp_processor_id() being used in preemptible code earlier in the boot
than before. This results in a new BUG from
pcibios_set_cache_line_size().
BUG: using smp_processor_id() in preemptible [00000000] code:
swapper/0/1 caller is pcibios_set_cache_line_size+0x10/0x70
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.13.0-rc1-00007-g3ce3e4ba4275 #615
Stack: 0000000000000000 ffffffff81189694 0000000000000000 ffffffff81822318
000000000000004e 0000000000000001 800000000e20bd08 20c49ba5e3540000
0000000000000000 0000000000000000 ffffffff818d0000 0000000000000000
0000000000000000 ffffffff81189328 ffffffff818ce692 0000000000000000
0000000000000000 ffffffff81189bc8 ffffffff818d0000 0000000000000000
ffffffff81828907 ffffffff81769970 800000020ec78d80 ffffffff818c7b48
0000000000000001 0000000000000001 ffffffff818652b0 ffffffff81896268
ffffffff818c0000 800000020ec7fb40 800000020ec7fc58 ffffffff81684cac
0000000000000000 ffffffff8118ab50 0000000000000030 ffffffff81769970
0000000000000001 ffffffff81122a58 0000000000000000 0000000000000000 ...
Call Trace:
[<ffffffff81122a58>] show_stack+0x90/0xb0
[<ffffffff81684cac>] dump_stack+0xac/0xf0
[<ffffffff813f7050>] check_preemption_disabled+0x120/0x128
[<ffffffff818855e8>] pcibios_set_cache_line_size+0x10/0x70
[<ffffffff81100578>] do_one_initcall+0x48/0x140
[<ffffffff81865dc4>] kernel_init_freeable+0x194/0x24c
[<ffffffff8169c534>] kernel_init+0x14/0x118
[<ffffffff8111ca84>] ret_from_kernel_thread+0x14/0x1c
Fix this by using the cpu_*cache_line_size() macros instead. These
macros are the "proper" way to determine the CPU cache sizes.
This makes use of the newly added cpu_tcache_line_size.
Fixes: 1c3c5eab1715 ("sched/core: Enable might_sleep() and smp_processor_id() checks early")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Suggested-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
There exist macros to return the cache line size of the L1 dcache and L2
scache but there is currently no macro for the L3 tcache. Add this macro
which will be used by the following patch "MIPS: PCI: Fix
smp_processor_id() in preemptible"
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16871/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-shared-2017-08-07
This series includes some mlx5 updates for both net-next and rdma trees.
From Saeed,
Core driver updates to allow selectively building the driver with
or without some large driver components, such as
- E-Switch (Ethernet SRIOV support).
- Multi-Physical Function Switch (MPFs) support.
For that we split E-Switch and MPFs functionalities into separate files.
From Erez,
Delay mlx5_core events when mlx5 interfaces, namely mlx5_ib, registration
is taking place and until it completes.
From Rabie,
Increase the maximum supported flow counters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
