| Age | Commit message (Collapse) | Author |
|---|
|
If max_phys_bits needs to be > 43 (f.e. for T4 chips), things like
DEBUG_PAGEALLOC stop working because the 3-level page tables only
can cover up to 43 bits.
Another problem is that when we increased MAX_PHYS_ADDRESS_BITS up to
47, several statically allocated tables became enormous.
Compounding this is that we will need to support up to 49 bits of
physical addressing for M7 chips.
The two tables in question are sparc64_valid_addr_bitmap and
kpte_linear_bitmap.
The first holds a bitmap, with 1 bit for each 4MB chunk of physical
memory, indicating whether that chunk actually exists in the machine
and is valid.
The second table is a set of 2-bit values which tell how large of a
mapping (4MB, 256MB, 2GB, 16GB, respectively) we can use at each 256MB
chunk of ram in the system.
These tables are huge and take up an enormous amount of the BSS
section of the sparc64 kernel image. Specifically, the
sparc64_valid_addr_bitmap is 4MB, and the kpte_linear_bitmap is 128K.
So let's solve the space wastage and the DEBUG_PAGEALLOC problem
at the same time, by using the kernel page tables (as designed) to
manage this information.
We have to keep using large mappings when DEBUG_PAGEALLOC is disabled,
and we do this by encoding huge PMDs and PUDs.
On a T4-2 with 256GB of ram the kernel page table takes up 16K with
DEBUG_PAGEALLOC disabled and 256MB with it enabled. Furthermore, this
memory is dynamically allocated at run time rather than coded
statically into the kernel image.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
|
|
As currently coded the KTSB accesses in the kernel only support up to
47 bits of physical addressing.
Adjust the instruction and patching sequence in order to support
arbitrary 64 bits addresses.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
|
|
Now that we use 4-level page tables, we can provide up to 53-bits of
virtual address space to the user.
Adjust the VA hole based upon the capabilities of the cpu type probed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
|
|
This has become necessary with chips that support more than 43-bits
of physical addressing.
Based almost entirely upon a patch by Bob Picco.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>
|
|
When we have to split up a flush request into multiple pieces
(in order to avoid the firmware range) we don't specify the
arguments in the right order for the second piece.
Fix the order, or else we get hangs as the code tries to
flush "a lot" of entries and we get lockups like this:
[ 4422.981276] NMI watchdog: BUG: soft lockup - CPU#12 stuck for 23s! [expect:117032]
[ 4422.996130] Modules linked in: ipv6 loop usb_storage igb ptp sg sr_mod ehci_pci ehci_hcd pps_core n2_rng rng_core
[ 4423.016617] CPU: 12 PID: 117032 Comm: expect Not tainted 3.17.0-rc4+ #1608
[ 4423.030331] task: fff8003cc730e220 ti: fff8003d99d54000 task.ti: fff8003d99d54000
[ 4423.045282] TSTATE: 0000000011001602 TPC: 00000000004521e8 TNPC: 00000000004521ec Y: 00000000 Not tainted
[ 4423.064905] TPC: <__flush_tlb_kernel_range+0x28/0x40>
[ 4423.074964] g0: 000000000052fd10 g1: 00000001295a8000 g2: ffffff7176ffc000 g3: 0000000000002000
[ 4423.092324] g4: fff8003cc730e220 g5: fff8003dfedcc000 g6: fff8003d99d54000 g7: 0000000000000006
[ 4423.109687] o0: 0000000000000000 o1: 0000000000000000 o2: 0000000000000003 o3: 00000000f0000000
[ 4423.127058] o4: 0000000000000080 o5: 00000001295a8000 sp: fff8003d99d56d01 ret_pc: 000000000052ff54
[ 4423.145121] RPC: <__purge_vmap_area_lazy+0x314/0x3a0>
[ 4423.155185] l0: 0000000000000000 l1: 0000000000000000 l2: 0000000000a38040 l3: 0000000000000000
[ 4423.172559] l4: fff8003dae8965e0 l5: ffffffffffffffff l6: 0000000000000000 l7: 00000000f7e2b138
[ 4423.189913] i0: fff8003d99d576a0 i1: fff8003d99d576a8 i2: fff8003d99d575e8 i3: 0000000000000000
[ 4423.207284] i4: 0000000000008008 i5: fff8003d99d575c8 i6: fff8003d99d56df1 i7: 0000000000530c24
[ 4423.224640] I7: <free_vmap_area_noflush+0x64/0x80>
[ 4423.234193] Call Trace:
[ 4423.239051] [0000000000530c24] free_vmap_area_noflush+0x64/0x80
[ 4423.251029] [0000000000531a7c] remove_vm_area+0x5c/0x80
[ 4423.261628] [0000000000531b80] __vunmap+0x20/0x120
[ 4423.271352] [000000000071cf18] n_tty_close+0x18/0x40
[ 4423.281423] [00000000007222b0] tty_ldisc_close+0x30/0x60
[ 4423.292183] [00000000007225a4] tty_ldisc_reinit+0x24/0xa0
[ 4423.303120] [0000000000722ab4] tty_ldisc_hangup+0xd4/0x1e0
[ 4423.314232] [0000000000719aa0] __tty_hangup+0x280/0x3c0
[ 4423.324835] [0000000000724cb4] pty_close+0x134/0x1a0
[ 4423.334905] [000000000071aa24] tty_release+0x104/0x500
[ 4423.345316] [00000000005511d0] __fput+0x90/0x1e0
[ 4423.354701] [000000000047fa54] task_work_run+0x94/0xe0
[ 4423.365126] [0000000000404b44] __handle_signal+0xc/0x2c
Fixes: 4ca9a23765da ("sparc64: Guard against flushing openfirmware mappings.")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the much more reader friendly ACCESS_ONCE() instead of the cast to volatile.
This is purely a stylistic change.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-arch@vger.kernel.org
Link: http://lkml.kernel.org/r/1411482607-20948-1-git-send-email-bobby.prani@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The vio_set_intr() API should be used by VIO consumers to enable/disable
Rx interrupts to facilitate deferred processing in softirq/bottom-half
context.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vio_dring_avail() will allow use of every dring entry, but when the last
entry is allocated then dr->prod == dr->cons which is indistinguishable from
the ring empty condition. This causes the next allocation to reuse an entry.
When this happens in sunvdc, the server side vds driver begins nack'ing the
messages and ends up resetting the ldc channel. This problem does not effect
sunvnet since it checks for < 2.
The fix here is to just never allocate the very last dring slot so that full
and empty are not the same condition. The request start path was changed to
check for the ring being full a bit earlier, and to stop the blk_queue if
there is no space left. The blk_queue will be restarted once the ring is
only half full again. The number of ring entries was increased to 512 which
matches the sunvnet and Solaris vdc drivers, and greatly reduces the
frequency of hitting the ring full condition and the associated blk_queue
stop/starting. The checks in sunvent were adjusted to account for
vio_dring_avail() returning 1 less.
Orabug: 19441666
OraBZ: 14983
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Interpret the media type from v1.1 protocol to support CDROM/DVD.
For v1.0 protocol, a disk's size continues to be calculated from the
geometry returned by the vdisk server. The geometry returned by the server
can be less than the actual number of sectors available in the backing
image/device due to the rounding in the division used to compute the
geometry in the vdisk server.
In v1.1 protocol a disk's actual size in sectors is returned during the
handshake. Use this size when v1.1 protocol is negotiated. Since this size
will always be larger than the former geometry computed size, disks created
under v1.0 will be forwards compatible to v1.1, but not vice versa.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add VIO protocol version 1.6 interfaces.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows an admin to set the MTU on a sunvnet device to arbitrary
values between the minimum (68) and maximum (65535) IPv4 packet sizes.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch upgrades the sunvnet driver to support VIO protocol version 1.6.
In particular, it adds per-port MTU negotiation, allowing MTUs other than
ETH_FRAMELEN with ports using newer VIO protocol versions.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We changed PAGE_OFFSET to be a variable rather than a constant,
but this reference here in the hibernate assembler got missed.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BPF_LD | BPF_W | BPF_LEN instruction is occasionally used by tcpdump
and present in 11 tests in lib/test_bpf.c
Teach sparc JIT compiler to emit it.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
- fix BPF_LD|ABS|IND from negative offsets:
make sure to sign extend lower 32 bits in 64-bit register
before calling C helpers from JITed code, otherwise 'int k'
argument of bpf_internal_load_pointer_neg_helper() function
will be added as large unsigned integer, causing packet size
check to trigger and abort the program.
It's worth noting that JITed code for 'A = A op K' will affect
upper 32 bits differently depending whether K is simm13 or not.
Since small constants are sign extended, whereas large constants
are stored in temp register and zero extended.
That is ok and we don't have to pay a penalty of sign extension
for every sethi, since all classic BPF instructions have 32-bit
semantics and we only need to set correct upper bits when
transitioning from JITed code into C.
- though instructions 'A &= 0' and 'A *= 0' are odd, JIT compiler
should not optimize them out
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are currently embedding the same check from thread_info.h into
syscall.h thanks to the way syscall_get_arch() was implemented in the
audit tree. Instead create a new function, is_32bit_task() which is
similar to that found on the powerpc arch. This simplifies the
syscall.h code and makes the build/Kconfig requirements much easier
to understand.
Signed-off-by: Eric Paris <eparis@redhat.com
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: sparclinux@vger.kernel.org
|
|
After merging the audit tree, today's linux-next build (sparc defconfig)
failed like this:
In file included from include/linux/audit.h:29:0,
from mm/mmap.c:33:
arch/sparc/include/asm/syscall.h: In function 'syscall_get_arch':
arch/sparc/include/asm/syscall.h:131:9: error: 'TIF_32BIT' undeclared (first use in this function)
arch/sparc/include/asm/syscall.h:131:9: note: each undeclared identifier is reported only once for each function it appears in
And many more ...
Caused by commit 374c0c054122 ("ARCH: AUDIT: implement syscall_get_arch
for all arches").
This patch wraps the usage of TIF_32BIT in:
if defined(__sparc__) && defined(__arch64__)
Which solves the build problem.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
|
|
We have a function where the arch can be queried, syscall_get_arch().
So rather than have every single piece of arch specific code use and/or
duplicate syscall_get_arch(), just have the audit code use the
syscall_get_arch() code.
Based-on-patch-by: Richard Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: linux-alpha@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-ia64@vger.kernel.org
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: linux-mips@linux-mips.org
Cc: linux@lists.openrisc.net
Cc: linux-parisc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-s390@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: linux-xtensa@linux-xtensa.org
Cc: x86@kernel.org
|
|
For all arches which support audit implement syscall_get_arch()
They are all pretty easy and straight forward, stolen from how the call
to audit_syscall_entry() determines the arch.
Based-on-patch-by: Richard Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: linux-ia64@vger.kernel.org
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: linux-mips@linux-mips.org
Cc: linux@lists.openrisc.net
Cc: linux-parisc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
|
|
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix several issues in sparc BPF JIT compiler.
ldx/stx related:
. classic BPF instructions that access mem[] slots were not setting
SEEN_MEM flag, so stack wasn't allocated. Fix that by advertising
correct flags
. LDX/STX instructions were missing SEEN_XREG, so register value
could have leaked to user space. Fix it.
. since stack for mem[] slots is allocated with 'sub %sp' instead
of 'save %sp', use %sp as base register instead of %fp.
. ldx mem[0] means first slot in classic BPF which should have
-4 offset instead of 0.
. sparc64 needs 2047 stack bias as per ABI to access stack
. emit_stmem() was using LD32I macro instead of ST32I
SKF_AD_VLAN_TAG* related:
. SKF_AD_VLAN_TAG_PRESENT must return 1 or 0 instead of '> 0' or 0
as per classic BPF de facto standard
. SKF_AD_VLAN_TAG needs to mask the field correctly
Fixes: 2809a2087cc4 ("net: filter: Just In Time compiler for sparc")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 233577a22089 ("net: filter: constify detection of pkt_type_offset")
allows us to implement simple PKTTYPE support in sparc JIT
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The request_irq() needs to be done from ldc_alloc()
to avoid the following (caught by lockdep)
[00000000004a0738] __might_sleep+0xf8/0x120
[000000000058bea4] kmem_cache_alloc_trace+0x184/0x2c0
[00000000004faf80] request_threaded_irq+0x80/0x160
[000000000044f71c] ldc_bind+0x7c/0x220
[0000000000452454] vio_port_up+0x54/0xe0
[00000000101f6778] probe_disk+0x38/0x220 [sunvdc]
[00000000101f6b8c] vdc_port_probe+0x22c/0x300 [sunvdc]
[0000000000451a88] vio_device_probe+0x48/0x60
[000000000074c56c] really_probe+0x6c/0x300
[000000000074c83c] driver_probe_device+0x3c/0xa0
[000000000074c92c] __driver_attach+0x8c/0xa0
[000000000074a6ec] bus_for_each_dev+0x6c/0xa0
[000000000074c1dc] driver_attach+0x1c/0x40
[000000000074b0fc] bus_add_driver+0xbc/0x280
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The T5 (niagara5) has different PCR related HV fast trap values and a new
HV API Group. This patch utilizes these and shares when possible with niagara4.
We use the same sparc_pmu niagara4_pmu. Should there be new effort to
obtain the MCU perf statistics then this would have to be changed.
Cc: sparclinux@vger.kernel.org
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "mem" boot option can result in many unexpected consequences. This patch
attempts to prevent boot hangs which have been experienced on T4-4 and T5-8.
Basically the boot loader allocates vmlinuz and initrd higher in available
OBP physical memory. For example, on a 2Tb T5-8 it isn't possible to boot
with mem=20G.
The patch utilizes memblock to avoid reserved regions and trim memory which
is only free. Other improvements are possible for a multi-node machine.
This is a snippet of the boot log with mem=20G on T5-8 with the patch applied:
MEMBLOCK configuration: <- before memory reduction
memory size = 0x1ffad6ce000 reserved size = 0xa1adf44
memory.cnt = 0xb
memory[0x0] [0x00000030400000-0x00003fdde47fff], 0x3fada48000 bytes
memory[0x1] [0x00003fdde4e000-0x00003fdde4ffff], 0x2000 bytes
memory[0x2] [0x00080000000000-0x00083fffffffff], 0x4000000000 bytes
memory[0x3] [0x00100000000000-0x00103fffffffff], 0x4000000000 bytes
memory[0x4] [0x00180000000000-0x00183fffffffff], 0x4000000000 bytes
memory[0x5] [0x00200000000000-0x00203fffffffff], 0x4000000000 bytes
memory[0x6] [0x00280000000000-0x00283fffffffff], 0x4000000000 bytes
memory[0x7] [0x00300000000000-0x00303fffffffff], 0x4000000000 bytes
memory[0x8] [0x00380000000000-0x00383fffc71fff], 0x3fffc72000 bytes
memory[0x9] [0x00383fffc92000-0x00383fffca1fff], 0x10000 bytes
memory[0xa] [0x00383fffcb4000-0x00383fffcb5fff], 0x2000 bytes
reserved.cnt = 0x2
reserved[0x0] [0x00380000000000-0x0038000117e7f8], 0x117e7f9 bytes
reserved[0x1] [0x00380004000000-0x0038000d02f74a], 0x902f74b bytes
...
MEMBLOCK configuration: <- after reduction of memory
memory size = 0x50a1adf44 reserved size = 0xa1adf44
memory.cnt = 0x4
memory[0x0] [0x00380000000000-0x0038000117e7f8], 0x117e7f9 bytes
memory[0x1] [0x00380004000000-0x0038050d01d74a], 0x50901d74b bytes
memory[0x2] [0x00383fffc92000-0x00383fffca1fff], 0x10000 bytes
memory[0x3] [0x00383fffcb4000-0x00383fffcb5fff], 0x2000 bytes
reserved.cnt = 0x2
reserved[0x0] [0x00380000000000-0x0038000117e7f8], 0x117e7f9 bytes
reserved[0x1] [0x00380004000000-0x0038000d02f74a], 0x902f74b bytes
...
Early memory node ranges
node 7: [mem 0x380000000000-0x38000117dfff]
node 7: [mem 0x380004000000-0x380f0d01bfff]
node 7: [mem 0x383fffc92000-0x383fffca1fff]
node 7: [mem 0x383fffcb4000-0x383fffcb5fff]
Could not find start_pfn for node 0
Could not find start_pfn for node 1
Could not find start_pfn for node 2
Could not find start_pfn for node 3
Could not find start_pfn for node 4
Could not find start_pfn for node 5
Could not find start_pfn for node 6
.
The patch was tested on T4-1, T5-8 and Jalap?no.
Cc: sparclinux@vger.kernel.org
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have seen an issue with guest boot into LDOM that causes early boot failures
because of no matching rules for node identitity of the memory. I analyzed this
on my T4 and concluded there might not be a solution. I saw the issue in
mainline too when booting into the control/primary domain - with guests
configured. Note, this could be a firmware bug on some older machines.
I'll provide a full explanation of the issues below. Should we not find a
matching BEST latency group for a real address (RA) then we will assume node 0.
On the T4-2 here with the information provided I can't see an alternative.
Technically the LDOM shown below should match the MBLOCK to the
favorable latency group. However other factors must be considered too. Were
the memory controllers configured "fine" grained interleave or "coarse"
grain interleaved - T4. Also should a "group" MD node be considered a NUMA
node?
There has to be at least one Machine Description (MD) "group" and hence one
NUMA node. The group can have one or more latency groups (lg) - more than one
memory controller. The current code chooses the smallest latency as the most
favorable per group. The latency and lg information is in MLGROUP below.
MBLOCK is the base and size of the RAs for the machine as fetched from OBP
/memory "available" property. My machine has one MBLOCK but more would be
possible - with holes?
For a T4-2 the following information has been gathered:
with LDOM guest
MEMBLOCK configuration:
memory size = 0x27f870000
memory.cnt = 0x3
memory[0x0] [0x00000020400000-0x0000029fc67fff], 0x27f868000 bytes
memory[0x1] [0x0000029fd8a000-0x0000029fd8bfff], 0x2000 bytes
memory[0x2] [0x0000029fd92000-0x0000029fd97fff], 0x6000 bytes
reserved.cnt = 0x2
reserved[0x0] [0x00000020800000-0x000000216c15c0], 0xec15c1 bytes
reserved[0x1] [0x00000024800000-0x0000002c180c1e], 0x7980c1f bytes
MBLOCK[0]: base[20000000] size[280000000] offset[0]
(note: "base" and "size" reported in "MBLOCK" encompass the "memory[X]" values)
(note: (RA + offset) & mask = val is the formula to detect a match for the
memory controller. should there be no match for find_node node, a return
value of -1 resulted for the node - BAD)
There is one group. It has these forward links
MLGROUP[1]: node[545] latency[1f7e8] match[200000000] mask[200000000]
MLGROUP[2]: node[54d] latency[2de60] match[0] mask[200000000]
NUMA NODE[0]: node[545] mask[200000000] val[200000000] (latency[1f7e8])
(note: "val" is the best lg's (smallest latency) "match")
no LDOM guest - bare metal
MEMBLOCK configuration:
memory size = 0xfdf2d0000
memory.cnt = 0x3
memory[0x0] [0x00000020400000-0x00000fff6adfff], 0xfdf2ae000 bytes
memory[0x1] [0x00000fff6d2000-0x00000fff6e7fff], 0x16000 bytes
memory[0x2] [0x00000fff766000-0x00000fff771fff], 0xc000 bytes
reserved.cnt = 0x2
reserved[0x0] [0x00000020800000-0x00000021a04580], 0x1204581 bytes
reserved[0x1] [0x00000024800000-0x0000002c7d29fc], 0x7fd29fd bytes
MBLOCK[0]: base[20000000] size[fe0000000] offset[0]
there are two groups
group node[16d5]
MLGROUP[0]: node[1765] latency[1f7e8] match[0] mask[200000000]
MLGROUP[3]: node[177d] latency[2de60] match[200000000] mask[200000000]
NUMA NODE[0]: node[1765] mask[200000000] val[0] (latency[1f7e8])
group node[171d]
MLGROUP[2]: node[1775] latency[2de60] match[0] mask[200000000]
MLGROUP[1]: node[176d] latency[1f7e8] match[200000000] mask[200000000]
NUMA NODE[1]: node[176d] mask[200000000] val[200000000] (latency[1f7e8])
(note: for this two "group" bare metal machine, 1/2 memory is in group one's
lg and 1/2 memory is in group two's lg).
Cc: sparclinux@vger.kernel.org
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We've witnessed a few TLB events causing the machine to power off because
of prom_halt. In one case it was some nfs related area during rmmod. Another
was an mmapper of /dev/mem. A more recent one is an ITLB issue with
a bad pagesize which could be a hardware bug. Bugs happen but we should
attempt to not power off the machine and/or hang it when possible.
This is a DTLB error from an mmapper of /dev/mem:
[root@sparcie ~]# SUN4V-DTLB: Error at TPC[fffff80100903e6c], tl 1
SUN4V-DTLB: TPC<0xfffff80100903e6c>
SUN4V-DTLB: O7[fffff801081979d0]
SUN4V-DTLB: O7<0xfffff801081979d0>
SUN4V-DTLB: vaddr[fffff80100000000] ctx[1250] pte[98000000000f0610] error[2]
.
This is recent mainline for ITLB:
[ 3708.179864] SUN4V-ITLB: TPC<0xfffffc010071cefc>
[ 3708.188866] SUN4V-ITLB: O7[fffffc010071cee8]
[ 3708.197377] SUN4V-ITLB: O7<0xfffffc010071cee8>
[ 3708.206539] SUN4V-ITLB: vaddr[e0003] ctx[1a3c] pte[2900000dcc800eeb] error[4]
.
Normally sun4v_itlb_error_report() and sun4v_dtlb_error_report() would call
prom_halt() and drop us to OF command prompt "ok". This isn't the case for
LDOMs and the machine powers off.
For the HV reported error of HV_ENORADDR for HV HV_MMU_MAP_ADDR_TRAP we cause
a SIGBUS error by qualifying it within do_sparc64_fault() for fault code mask
of FAULT_CODE_BAD_RA. This is done when trap level (%tl) is less or equal
one("1"). Otherwise, for %tl > 1, we proceed eventually to die_if_kernel().
The logic of this patch was partially inspired by David Miller's feedback.
Power off of large sparc64 machines is painful. Plus die_if_kernel provides
more context. A reset sequence isn't a brief period on large sparc64 but
better than power-off/power-on sequence.
Cc: sparclinux@vger.kernel.org
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nohz full code needs irq work to trigger its own interrupt so that
the subsystem can work even when the tick is stopped.
Lets introduce arch_irq_work_has_interrupt() that archs can override to
tell about their support for this ability.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
|
dma_zalloc_coherent() calls dma_alloc_coherent(__GFP_ZERO)
but the sparc32 implementations sbus_alloc_coherent() and
pci32_alloc_coherent() doesn't take the gfp flags into
account.
Tested on the SPARC32/LEON GRETH Ethernet driver which fails
due to dma_alloc_coherent(__GFP_ZERO) returns non zeroed
pages.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch folding the atomic ops had a silly fail in the _return primitives.
Fixes: 4f3316c2b5fe ("locking,arch,sparc: Fold atomic_ops")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: sparclinux@vger.kernel.org
Link: http://lkml.kernel.org/r/20140902094016.GD31157@worktop.ger.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit: e676253b19b2d269cccf67fdb1592120a0cd0676 (serial/8250: Add
support for RS485 IOCTLs), adds support for RS485 ioctls for 825_core on
all the archs. Unfortunaltely the definition of TIOCSRS485 and
TIOCGRS485 was missing on the ioctls.h file
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Reported by Mikulas Patocka, kmemcheck currently barks out a
false positive since we don't have special kmemcheck annotation
for bitfields used in bpf_prog structure.
We currently have jited:1, len:31 and thus when accessing len
while CONFIG_KMEMCHECK enabled, kmemcheck throws a warning that
we're reading uninitialized memory.
As we don't need the whole bit universe for pages member, we
can just split it to u16 and use a bool flag for jited instead
of a bitfield.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The leon_dma_ops struct is needed for leon regardless of PCI configuration.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This makes sure that leon_cycles_offset takes the pending bit into
account and that leon_clear_clock_irq clears the pending bit. Otherwise,
if leon_cycles_offset is executed after the timer has wrapped but before
timer_interrupt has increased timer_cs_internal_counter, time can be
perceived to go backwards.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This makes memset follow the standard (instead of returning 0 on success). This
is needed when certain versions of gcc optimizes around memset calls and assume
that the address argument is preserved in %o0.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add M6 and M7 chip type in cpumap.c to correctly build CPU distribution map that spans all online CPUs.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following patch adds support for correctly
recognising M6 and M7 cpu type.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With eBPF getting more extended and exposure to user space is on it's way,
hardening the memory range the interpreter uses to steer its command flow
seems appropriate. This patch moves the to be interpreted bytecode to
read-only pages.
In case we execute a corrupted BPF interpreter image for some reason e.g.
caused by an attacker which got past a verifier stage, it would not only
provide arbitrary read/write memory access but arbitrary function calls
as well. After setting up the BPF interpreter image, its contents do not
change until destruction time, thus we can setup the image on immutable
made pages in order to mitigate modifications to that code. The idea
is derived from commit 314beb9bcabf ("x86: bpf_jit_comp: secure bpf jit
against spraying attacks").
This is possible because bpf_prog is not part of sk_filter anymore.
After setup bpf_prog cannot be altered during its life-time. This prevents
any modifications to the entire bpf_prog structure (incl. function/JIT
image pointer).
Every eBPF program (including classic BPF that are migrated) have to call
bpf_prog_select_runtime() to select either interpreter or a JIT image
as a last setup step, and they all are being freed via bpf_prog_free(),
including non-JIT. Therefore, we can easily integrate this into the
eBPF life-time, plus since we directly allocate a bpf_prog, we have no
performance penalty.
Tested with seccomp and test_bpf testsuite in JIT/non-JIT mode and manual
inspection of kernel_page_tables. Brad Spengler proposed the same idea
via Twitter during development of this patch.
Joint work with Hannes Frederic Sowa.
Suggested-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x). This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less registers
are used when code is generated.
At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.
The patch set includes passes over all arches as well. Once these operations
are used throughout then specialized macros can be defined in non -x86
arches as well in order to optimize per cpu access by f.e. using a global
register that may be set to the per cpu base.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
__this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
__this_cpu_inc(y)
Cc: sparclinux@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Many of the atomic op implementations are the same except for one
instruction; fold the lot into a few CPP macros and reduce LoC.
This also prepares for easy addition of new ops.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kirill Tkhai <tkhai@yandex.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: sparclinux@vger.kernel.org
Link: http://lkml.kernel.org/r/20140508135852.825281379@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Perform a pci_claim_resource() on all valid resources discovered
during the OF device tree scan.
Based almost entirely upon the PCI OF bus probing code which does
the same thing there.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems that when a PCI Express bridge is not in use and has no devices
behind it, the ranges property is bogus. Specifically the size property
is of the form [0xffffffff:...], and if you add this size to the resource
start address the 64-bit calculation will overflow.
Just check specifically for this size value signature and skip them.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dump the various aspects of the PCI bridge probed at boot time, most
importantly the bridge number ranges, and the ranges property.
This helps diagnose PCI resource issues and other problems by giving
ofpci_debug=1 on the boot command line.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull Sparc fixes from David Miller:
"Sparc bug fixes, one of which was preventing successful SMP boots with
mainline"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix pcr_ops initialization and usage bugs.
sparc64: Do not disable interrupts in nmi_cpu_busy()
sparc: Hook up seccomp and getrandom system calls.
sparc: fix decimal printf format specifiers prefixed with 0x
|
|
Christopher reports that perf_event_print_debug() can crash in uniprocessor
builds. The crash is due to pcr_ops being NULL.
This happens because pcr_arch_init() is only invoked by smp_cpus_done() which
only executes in SMP builds.
init_hw_perf_events() is closely intertwined with pcr_ops being setup properly,
therefore:
1) Call pcr_arch_init() early on from init_hw_perf_events(), instead of
from smp_cpus_done().
2) Do not hook up a PMU type if pcr_ops is NULL after pcr_arch_init().
3) Move init_hw_perf_events to a later initcall so that it we will be
sure to invoke pcr_arch_init() after all cpus are brought up.
Finally, guard the one naked sequence of pcr_ops dereferences in
__global_pmu_self() with an appropriate NULL check.
Reported-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nmi_cpu_busy() is a SMP function call that just makes sure that all of the
cpus are spinning using cpu cycles while the NMI test runs.
It does not need to disable IRQs because we just care about NMIs executing
which will even with 'normal' IRQs disabled.
It is not legal to enable hard IRQs in a SMP cross call, in fact this bug
triggers the BUG check in irq_work_run_list():
BUG_ON(!irqs_disabled());
Because now irq_work_run() is invoked from the tail of
generic_smp_call_function_single_interrupt().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
