| Age | Commit message (Collapse) | Author |
|---|
|
This patch is borrowed from x86 hpet driver and explaind below:
Due to the overly intelligent design of HPETs, we need to workaround
the problem that the compare value which we write is already behind
the actual counter value at the point where the value hits the real
compare register. This happens for two reasons:
1) We read out the counter, add the delta and write the result to the
compare register. When a NMI hits between the read out and the write
then the counter can be ahead of the event already.
2) The write to the compare register is delayed by up to two HPET
cycles in AMD chipsets.
We can work around this by reading back the compare register to make
sure that the written value has hit the hardware. But that is bad
performance wise for the normal case where the event is far enough in
the future.
As we already know that the write can be delayed by up to two cycles
we can avoid the read back of the compare register completely if we
make the decision whether the delta has elapsed already or not based
on the following calculation:
cmp = event - actual_count;
If cmp is less than 64 HPET clock cycles, then we decide that the event
has happened already and return -ETIME. That covers the above #1 and #2
problems which would cause a wait for HPET wraparound (~306 seconds).
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12162/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
When Core-0 handle SMP_ASK_C0COUNT IPI, we should make other cores to
see the result as soon as possible (especially when Store-Fill-Buffer
is enabled). Otherwise, C0_Count syncronization makes no sense.
BTW, array is more suitable than per-cpu variable for syncronization,
and there is a corner case should be avoid: C0_Count of Core-0 can be
really 0.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/12160/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
If GCC >= 4.9 and Binutils >=2.25, we use -march=loongson3a, otherwise
we use -march=mips64r2, this can slightly improve performance. Besides,
arch/mips/loongson64/Platform is a better location rather than arch/
mips/Makefile.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12161/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
In history, __arch_local_irq_restore() is only used by SMTC. However,
SMTC support has been removed since 3.16, this patch remove the unused
function.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12159/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The legacy-style mailbox device creation is supported currently
only for OMAP3, as all other SoCs are DT-boot only. Even on this
SoC, there are no client drivers that utilize these mailbox devices.
So, clean up the legacy-style mailbox device instantiation logic.
The mailbox devices are already present and supported for the DT
boot on OMAP3.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add ti,mbox-send-noirq to wkup_m3 mailbox so that messages using
wkup_m3 mailbox are sent without triggering any further interrupts.
This is required to be able to send multiple messages to the WkupM3
after the mailbox usage logic adjustment in the wkup_m3_ipc driver.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Dave Gerlach <d-gerlach@ti.com>
[s-anna@ti.com: revise commit description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add ti,mbox-send-noirq to wkup_m3 mailbox so that messages using
wkup_m3 mailbox are sent without triggering any further interrupts.
This is needed to achieve lower power numbers during CPU idle on
AM33xx.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[s-anna@ti.com: revise commit description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Expose an interface to allow users to mark several accesses together as
being user space accesses, allowing batching of the surrounding user
space access markers (SMAP on x86, PAN on arm64, domain register
switching on arm).
This is currently only used for the user string lenth and copying
functions, where the SMAP overhead on x86 drowned the actual user
accesses (only noticeable on newer microarchitectures that support SMAP
in the first place, of course).
* user access batching branch:
Use the new batched user accesses in generic user string handling
Add 'unsafe' user access functions for batched accesses
x86: reorganize SMAP handling in user space accesses
|
|
Merge third patch-bomb from Andrew Morton:
"I'm pretty much done for -rc1 now:
- the rest of MM, basically
- lib/ updates
- checkpatch, epoll, hfs, fatfs, ptrace, coredump, exit
- cpu_mask simplifications
- kexec, rapidio, MAINTAINERS etc, etc.
- more dma-mapping cleanups/simplifications from hch"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (109 commits)
MAINTAINERS: add/fix git URLs for various subsystems
mm: memcontrol: add "sock" to cgroup2 memory.stat
mm: memcontrol: basic memory statistics in cgroup2 memory controller
mm: memcontrol: do not uncharge old page in page cache replacement
Documentation: cgroup: add memory.swap.{current,max} description
mm: free swap cache aggressively if memcg swap is full
mm: vmscan: do not scan anon pages if memcg swap limit is hit
swap.h: move memcg related stuff to the end of the file
mm: memcontrol: replace mem_cgroup_lruvec_online with mem_cgroup_online
mm: vmscan: pass memcg to get_scan_count()
mm: memcontrol: charge swap to cgroup2
mm: memcontrol: clean up alloc, online, offline, free functions
mm: memcontrol: flatten struct cg_proto
mm: memcontrol: rein in the CONFIG space madness
net: drop tcp_memcontrol.c
mm: memcontrol: introduce CONFIG_MEMCG_LEGACY_KMEM
mm: memcontrol: allow to disable kmem accounting for cgroup2
mm: memcontrol: account "kmem" consumers in cgroup2 memory controller
mm: memcontrol: move kmem accounting code to CONFIG_MEMCG
mm: memcontrol: separate kmem code from legacy tcp accounting code
...
|
|
This patch replace the assoication between dsaf and enet from string
matching to object reference. It requires the DTS to be updated within
BIOS. Thanks god it can be done for all released boards.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes for the v4.5 merge window:
Enumeration:
- Simplify config space size computation (Bjorn Helgaas)
- Avoid iterating through ROM outside the resource window (Edward O'Callaghan)
- Support PCIe devices with short cfg_size (Jason S. McMullan)
- Add Netronome vendor and device IDs (Jason S. McMullan)
- Limit config space size for Netronome NFP6000 family (Jason S. McMullan)
- Add Netronome NFP4000 PF device ID (Simon Horman)
- Limit config space size for Netronome NFP4000 (Simon Horman)
- Print warnings for all invalid expansion ROM headers (Vladis Dronov)
Resource management:
- Fix minimum allocation address overwrite (Christoph Biedl)
PCI device hotplug:
- acpiphp_ibm: Fix null dereferences on null ibm_slot (Colin Ian King)
- pciehp: Always protect pciehp_disable_slot() with hotplug mutex (Guenter Roeck)
- shpchp: Constify hpc_ops structure (Julia Lawall)
- ibmphp: Remove unneeded NULL test (Julia Lawall)
Power management:
- Make ASPM sysfs link_state_store() consistent with link_state_show() (Andy Lutomirski)
Virtualization
- Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183 (Tim Sander)
MSI:
- Remove empty pci_msi_init_pci_dev() (Bjorn Helgaas)
- Mark PCIe/PCI (MSI) IRQ cascade handlers as IRQF_NO_THREAD (Grygorii Strashko)
- Initialize MSI capability for all architectures (Guilherme G. Piccoli)
- Relax msi_domain_alloc() to support parentless MSI irqdomains (Liu Jiang)
ARM Versatile host bridge driver:
- Remove unused pci_sys_data structures (Lorenzo Pieralisi)
Broadcom iProc host bridge driver:
- Hide CONFIG_PCIE_IPROC (Arnd Bergmann)
- Do not use 0x in front of %pap (Dmitry V. Krivenok)
- Update iProc PCIe device tree binding (Ray Jui)
- Add PAXC interface support (Ray Jui)
- Add iProc PCIe MSI device tree binding (Ray Jui)
- Add iProc PCIe MSI support (Ray Jui)
Freescale i.MX6 host bridge driver:
- Use gpio_set_value_cansleep() (Fabio Estevam)
- Add support for active-low reset GPIO (Petr Štetiar)
HiSilicon host bridge driver:
- Add support for HiSilicon Hip06 PCIe host controllers (Gabriele Paoloni)
Intel VMD host bridge driver:
- Export irq_domain_set_info() for module use (Keith Busch)
- x86/PCI: Allow DMA ops specific to a PCI domain (Keith Busch)
- Use 32 bit PCI domain numbers (Keith Busch)
- Add driver for Intel Volume Management Device (VMD) (Keith Busch)
Qualcomm host bridge driver:
- Document PCIe devicetree bindings (Stanimir Varbanov)
- Add Qualcomm PCIe controller driver (Stanimir Varbanov)
- dts: apq8064: add PCIe devicetree node (Stanimir Varbanov)
- dts: ifc6410: enable PCIe DT node for this board (Stanimir Varbanov)
Renesas R-Car host bridge driver:
- Add support for R-Car H3 to pcie-rcar (Harunobu Kurokawa)
- Allow DT to override default window settings (Phil Edworthy)
- Convert to DT resource parsing API (Phil Edworthy)
- Revert "PCI: rcar: Build pcie-rcar.c only on ARM" (Phil Edworthy)
- Remove unused pci_sys_data struct from pcie-rcar (Phil Edworthy)
- Add runtime PM support to pcie-rcar (Phil Edworthy)
- Add Gen2 PHY setup to pcie-rcar (Phil Edworthy)
- Add gen2 fallback compatibility string for pci-rcar-gen2 (Simon Horman)
- Add gen2 fallback compatibility string for pcie-rcar (Simon Horman)
Synopsys DesignWare host bridge driver:
- Simplify control flow (Bjorn Helgaas)
- Make config accessor override checking symmetric (Bjorn Helgaas)
- Ensure ATU is enabled before IO/conf space accesses (Stanimir Varbanov)
Miscellaneous:
- Add of_pci_get_host_bridge_resources() stub (Arnd Bergmann)
- Check for PCI_HEADER_TYPE_BRIDGE equality, not bitmask (Bjorn Helgaas)
- Fix all whitespace issues (Bogicevic Sasa)
- x86/PCI: Simplify pci_bios_{read,write} (Geliang Tang)
- Use to_pci_dev() instead of open-coding it (Geliang Tang)
- Use kobj_to_dev() instead of open-coding it (Geliang Tang)
- Use list_for_each_entry() to simplify code (Geliang Tang)
- Fix typos in <linux/msi.h> (Thomas Petazzoni)
- x86/PCI: Clarify AMD Fam10h config access restrictions comment (Tomasz Nowicki)"
* tag 'pci-v4.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (58 commits)
PCI: Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183
PCI: Limit config space size for Netronome NFP4000
PCI: Add Netronome NFP4000 PF device ID
x86/PCI: Add driver for Intel Volume Management Device (VMD)
PCI/AER: Use 32 bit PCI domain numbers
x86/PCI: Allow DMA ops specific to a PCI domain
irqdomain: Export irq_domain_set_info() for module use
PCI: host: Add of_pci_get_host_bridge_resources() stub
genirq/MSI: Relax msi_domain_alloc() to support parentless MSI irqdomains
PCI: rcar: Add Gen2 PHY setup to pcie-rcar
PCI: rcar: Add runtime PM support to pcie-rcar
PCI: designware: Make config accessor override checking symmetric
PCI: ibmphp: Remove unneeded NULL test
ARM: dts: ifc6410: enable PCIe DT node for this board
ARM: dts: apq8064: add PCIe devicetree node
PCI: hotplug: Use list_for_each_entry() to simplify code
PCI: rcar: Remove unused pci_sys_data struct from pcie-rcar
PCI: hisi: Add support for HiSilicon Hip06 PCIe host controllers
PCI: Avoid iterating through memory outside the resource window
PCI: acpiphp_ibm: Fix null dereferences on null ibm_slot
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull CRIS updates from Jesper Nilsson:
"Just some fixups for section mismatches from Guenter"
* tag 'cris-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: Fix section mismatches in architecture startup code
cris: debugport: Fix section mismatches
|
|
Pull h8300 updates from Yoshinori Sato:
- Add KGDB support
- zImage fix
- various cleanup
* tag 'for-4.5' of git://git.osdn.jp/gitroot/uclinux-h8/linux:
h8300: System call entry enable interrupt.
h8300: show_stack cleanup
h8300: Restraint of warning.
h8300: Add KGDB support.
irqchip: renesas-h8s: Replace ctrl_outw/ctrl_inw with writew/readw
h8300: signal stack fix
h8300: Add LZO compression
h8300: zImage alignment fix
clk: h8300: Remove "sh73a0-" part from compatible value
h8300: zImage alignment fix
|
|
This patch enables the uncore_imc PMU for Intel
SkyLake Desktop processors (Core i7-6700, model 94).
It is possible to compute memory read/write bandwidth
using:
$ perf stat -a -e uncore_imc/data_reads/,uncore_imc/data_writes/ ....
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: kan.liang@intel.com
Link: http://lkml.kernel.org/r/1452151546-8853-1-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
As it happens, two obj-$(CONFIG_FOO) += foo.o variables are
above obj-y := core.o, which doesn't work: the += directives
need to add something to the build and doesn't work if obj-y
is not set first, so move the obj-y to be on top and everything
builds nicely again.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When we print values, such as @size, we have to understand that
it's derived from [begin .. end] as:
size = end - begin + 1
On the opposite the @end is derived from the rest as:
end = begin + size - 1
Correct the IMR code to print values correctly.
Note that @__end_rodata actually points to the next address
after the aligned .rodata section.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ong, Boon Leong <boon.leong.ong@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1453320821-64328-1-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit d5d6a443b243 ("arch/powerpc/include/asm/pgtable-ppc64.h:
add pmd_[dirty|mkclean] for THP") added a new identical definition
of pmd_dirty(). Remove it again.
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
PowerPC64 uses the symbol .TOC. much as other targets use
_GLOBAL_OFFSET_TABLE_. It identifies the value of the GOT pointer (or in
powerpc parlance, the TOC pointer). Global offset tables are generally
local to an executable or shared library, or in the kernel, module. Thus
it does not make sense for a module to resolve a relocation against
.TOC. to the kernel's .TOC. value. A module has its own .TOC., and
indeed the powerpc64 module relocation processing ignores the kernel
value of .TOC. and instead calculates a module-local value.
This patch removes code involved in exporting the kernel .TOC., tweaks
modpost to ignore an undefined .TOC., and the module loader to twiddle
the section symbol so that .TOC. isn't seen as undefined.
Note that if the kernel was compiled with -msingle-pic-base then ELFv2
would not have function global entry code setting up r2. In that case
the module call stubs would need to be modified to set up r2 using the
kernel .TOC. value, requiring some of this code to be reinstated.
mpe: Furthermore a change in binutils master (not yet released) causes
the current way we handle the TOC to no longer work when building with
MODVERSIONS=y and RELOCATABLE=n. The symptom is that modules can not be
loaded due to there being no version found for TOC.
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Alan Modra <amodra@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Test runs on a ppc64 BE guest succeeded using modified fstests.
Also tested on ppc64 LE using a home made test - mpe.
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"This includes fixes on top of the previous batch of PM+ACPI updates
and some new material as well.
From the new material perspective the most significant are the driver
core changes that should allow USB devices to stay suspended over
system suspend/resume cycles if they have been runtime-suspended
already beforehand. Apart from that, ACPICA is updated to upstream
revision 20160108 (cosmetic mostly, but including one fixup on top of
the previous ACPICA update) and there are some devfreq updates the
didn't make it before (due to timing).
A few recent regressions are fixed, most importantly in the cpuidle
menu governor and in the ACPI backlight driver and some x86 platform
drivers depending on it.
Some more bugs are fixed and cleanups are made on top of that.
Specifics:
- Modify the driver core and the USB subsystem to allow USB devices
to stay suspended over system suspend/resume cycles if they have
been runtime-suspended already beforehand and fix some bugs on top
of these changes (Tomeu Vizoso, Rafael Wysocki).
- Update ACPICA to upstream revision 20160108, including updates of
the ACPICA's copyright notices, a code fixup resulting from a
regression fix that was necessary in the upstream code only (the
regression fixed by it has never been present in Linux) and a
compiler warning fix (Bob Moore, Lv Zheng).
- Fix a recent regression in the cpuidle menu governor that broke it
on practically all architectures other than x86 and make a couple
of optimizations on top of that fix (Rafael Wysocki).
- Clean up the selection of cpuidle governors depending on whether or
not the kernel is configured for tickless systems (Jean Delvare).
- Revert a recent commit that introduced a regression in the ACPI
backlight driver, address the problem it attempted to fix in a
different way and revert one more cosmetic change depending on the
problematic commit (Hans de Goede).
- Add two more ACPI backlight quirks (Hans de Goede).
- Fix a few minor problems in the core devfreq code, clean it up a
bit and update the MAINTAINERS information related to it (Chanwoo
Choi, MyungJoo Ham).
- Improve an error message in the ACPI fan driver (Andy Lutomirski).
- Fix a recent build regression in the cpupower tool (Shreyas
Prabhu)"
* tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
cpuidle: menu: Avoid pointless checks in menu_select()
sched / idle: Drop default_idle_call() fallback from call_cpuidle()
cpupower: Fix build error in cpufreq-info
cpuidle: Don't enable all governors by default
cpuidle: Default to ladder governor on ticking systems
time: nohz: Expose tick_nohz_enabled
ACPICA: Update version to 20160108
ACPICA: Silence a -Wbad-function-cast warning when acpi_uintptr_t is 'uintptr_t'
ACPICA: Additional 2016 copyright changes
ACPICA: Reduce regression fix divergence from upstream ACPICA
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Satellite R830
ACPI / video: Revert "thinkpad_acpi: Use acpi_video_handles_brightness_key_presses()"
ACPI / video: Document acpi_video_handles_brightness_key_presses() a bit
ACPI / video: Fix using an uninitialized mutex / list_head in acpi_video_handles_brightness_key_presses()
ACPI / video: Revert "ACPI / video: driver must be registered before checking for keypresses"
ACPI / fan: Improve acpi_device_update_power error message
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Portege R700
cpuidle: menu: Fix menu_select() for CPUIDLE_DRIVER_STATE_START == 0
MAINTAINERS: Add devfreq-event entry
MAINTAINERS: Add missing git repository and directory for devfreq
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs. Some for SoC-family code under
drivers/soc, but also some other driver updates that don't belong
anywhere else. We also bring in the drivers/reset code through
arm-soc.
Some of the larger updates:
- Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate
with other parts of the chip/board on these platforms, all
proprietary protocols that don't fit into other subsystems and live
in drivers/soc for now.
- System bus driver for UniPhier
- Driver for the TI Wakeup M3 IPC device
- Power management for Raspberry PI
+ Again a bunch of other smaller updates and patches"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: uniphier: allow only built-in driver
ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency
MAINTAINERS: Drop Kumar Gala from QCOM
bus: uniphier-system-bus: add UniPhier System Bus driver
ARM: bcm2835: add rpi power domain driver
dt-bindings: add rpi power domain driver bindings
ARM: bcm2835: Define two new packets from the latest firmware.
drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular
soc: mediatek: SCPSYS: Add regulator support
MAINTAINERS: Change QCOM entries
soc: qcom: smd-rpm: Add existing platform support
memory/tegra: Add number of TLB lines for Tegra124
reset: hi6220: fix modular build
soc: qcom: Introduce WCNSS_CTRL SMD client
ARM: qcom: select ARM_CPU_SUSPEND for power management
MAINTAINERS: Add rules for Qualcomm dts files
soc: qcom: enable smsm/smp2p modular build
serial: msm_serial: Make config tristate
soc: qcom: smp2p: Qualcomm Shared Memory Point to Point
soc: qcom: smsm: Add driver for Qualcomm SMSM
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit defconfig updates from Olof Johansson:
"As mentioned earlier, we usually bake this into the general "arm64"
branch, but this release we have partitioned up the updates a bit
more.
Most of these updates are enabling new SoCs in the single defconfig
for 64-bit, Renesas R8A7795, a number of Tegra options, Socionext
Uniphier and a handful of new options for other platforms as well"
* tag 'armsoc-defconfig64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: mediatek: enable MTK_TIMER
arm64: defconfig: add CS2000 support
arm64: defconfig: Add Renesas R-Car SATA driver for R-Car Gen3 SoCs
arm64: defconfig: enable UniPhier SoCs support
arm64: add Kconfig entry for Socionext UniPhier SoC family
arm64: defconfig: add Renesas sound and AK4613 support
arm64: defconfig: add Renesas R-Car DMAC driver support
arm64: defconfig: Enable Renesas R-Car I2C Controller
arm64: defconfig: enable EthernetAVB
arm64: defconfig: Enable GPIO of Renesas R-Car Gen3 SoC
arm64: berlin: add the pinctrl dependency for Marvell Berlin SoCs
arm64: defconfig: renesas: Enable Renesas r8a7795 SoC
arm64: defconfig: Enable printk timestamps
arm64: defconfig: Enable squashfs support
arm64: defconfig: Enable sdhci-tegra driver
arm64: defconfig: Enable serial-tegra driver
arm64: defconfig: Enable tegra-apbdma driver
arm64: defconfig: Do not disable Tegra AHB driver
arm64: defconfig: Enable Tegra210 support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Olof Johansson:
"As usual, a bunch of commits, mostly adding drivers and other options
to defconfigs because it makes sense to have them enabled on various
development or product boards. Too much to enumerate each here.
There's an introduction of a pxa_defconfig, since PXA finally will
allow building a shared kernel for all boards. With this, we can
hopefully remove a bunch of individual defconfigs down the road but it
requires a bit of real life testing and transition period"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
ARM: Add CONFIG_DEPRECATED_PARAM_STRUCT to netwinder_defconfig
ARM: multi_v7_defconfig: Add rockchip audio support
arm: multi_v7_defconfig: Add virtio drivers
ARM: zx_defconfig: remove CONFIG_MMC_DW_IDMAC
ARM: versatile: enable the right LEDs
ARM: pxa: add defconfig covering all the boards
ARM: versatile: select some defaults in defconfig
ARM: multi_v7_defconfig: Enable fan, sensors and audio for Odroid XU3
ARM: bcm2835: enable auxiliary spi driver in defconfig
ARM: bcm2835: enable all bcm2835-relevant in defconfig
ARM: default to multi_v7_defconfig
ARM: multi_v7_defconfig: enable rk808 clkout module
ARM: multi_v7_defconfig: enable rockchip crypto module
ARM: multi_v7_defconfig: enable Rockchip io-domain driver
ARM: multi_v7_defconfig: Enable generic SoC internal OMAP regulators
ARM: multi_v7_defconfig: Enable AM437x PMIC TPS65218
ARM: multi_v7_defconfig: enable TPS65217 regulator
ARM: realview: select apropriate targets
ARM: defconfig: qcom: Enable SSBI drivers
ARM: defconfig: Update qcom_defconfig
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"This is the first release where we split up the 64-bit contributions a
bit more, and in particular we are having a separate DT branch for
them.
Contents:
- New devices added to Broadcom NorthStar2
- Misc fixes for Exynos7 boards
- QCOM updates for MSM8916
- Rockchip tweaks for rk3368 SoC and eval board
- A series of fixes for APM X-Gene v1 and v2
- Renesas R8A7795 CPU/PSCI additions
- Marvell Berlin4CT PSCI, cpuidle, watchdog portions
- Freescale LS1043a SoC and dev board support
+ some treewide or other misc changes"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (104 commits)
dts/ls2080a: Update DTSI to add support of SP805 WDT
Documentation: DT: Add entry for ARM SP805-WDT
arm64: dts: X-Gene v2: I2C1 clock is always on
arm64: dts: X-Gene v1: I2C0 clock is always on
arm64: dts: Fix to use standard DT node names for X-Gene 1 and X-Gene 2 platforms
arm64: dts: hikey: add label properties to UARTs
arm64: dts: apq8016-sbc: add label properties for UART, I2C, and SPI
arm64: dts: apq8016-sbc: enable UART0 on LS connector
arm64: dts: juno: Add idle-states to device tree
arm64: dts: Added syscon-reboot node for FSL's LS2080A SoC
arm64: dts: add LS1043a-RDB board support
arm64: dts: add Freescale LS1043a SoC support
Documentation: DT: Add entry for Freescale LS1043a-RDB board
arm64: dts: uniphier: add PH1-LD10 SoC/board support
arm64: renesas: r8a7795: fix SATA clock assignment
arm64: dts: salvator-x: Enable SATA controller
arm64: dts: r8a7795: Add SATA controller node
arm64: renesas: r8a7795: add internal delay for i2c IPs
arm64: renesas: salvator-x: Add board part number to DT bindings
arm64: dts: r8a7795: Add pmu device nodes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a
crisp overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (469 commits)
ARM: dts: compulab: add new board description
ARM: versatile: add the syscon LEDs to the DT
dts: vt8500: Fix errors in SDHC node for WM8505
ARM: dts: imx6q: clean up unused ipu2grp
ARM: dts: silk: Add compatible property to "partitions" node
ARM: dts: gose: Add compatible property to "partitions" node
ARM: dts: porter: Add compatible property to "partitions" node
ARM: dts: koelsch: Add compatible property to "partitions" node
ARM: dts: lager: Add compatible property to "partitions" node
ARM: dts: bockw: Add compatible property to "partitions" node
ARM: dts: meson8b: Add watchdog node
Documentation: watchdog: Add new bindings for meson8b
ARM: meson: Add status LED for Odroid-C1
ARM: dts: uniphier: fix a typo in comment block
ARM: bcm2835: Add the auxiliary clocks to the device tree.
ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT.
ARM: bcm2835: Split the DT for peripherals from the DT for the CPU
ARM: realview: set up cache correctly on the PB11MPCore
ARM: dts: Unify G2D device node with other devices on exynos4
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Updates for new platform support:
- New platform: Tango4 from Sigma Designs.
- Broadcom BCM2836 (Raspberry Pi 2 SoC)
- Enable cpufreq on Freescale i.MX7D
- Rockchip: SMP support for rk3036, general support for rk3228
- SMP support on Broadcom Kona and NSP
- Cleanups for OMAP removing legacy IOMMU data
+ a bunch of misc fixes and tweaks for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
ARM: tango: Fix UP build issues
ARM: tango: pass ARM arch level for smc.S
ARM: bcm2835: Add Kconfig support for bcm2836
ARM: OMAP2+: Add support for dm814x and dra62x usb
ARM: OMAP2+: Add mmc hwmod entries for dm814x
ARM: OMAP2+: Update 81xx clock and power domains for default, active and sgx
ARM: OMAP2+: Fix SoC detection for dra62x j5-eco
ARM: tango4: Initial platform support
ARM: bcm2835: Add a compat string for bcm2836 machine probe
dt-bindings: Add root properties for Raspberry Pi 2
ARM: imx: select SRC for i.MX7
ARM: uniphier: select PINCTRL
ARM: OMAP2+: Remove device creation for omap-pcm-audio
ARM: OMAP1: Remove device creation for omap-pcm-audio
ARM: rockchip: enable support for RK3228 SoCs
ARM: rockchip: use const and __initconst for rk3036 smp_operations
ARM: zynq: Select ARCH_HAS_RESET_CONTROLLER
ARM: BCM: Add SMP support for Broadcom 4708
ARM: BCM: Add SMP support for Broadcom NSP
ARM: BCM: Clean up SMP support for Broadcom Kona
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"A smallish number of general cleanup commits this release cycle. Some
of these are minor tweaks:
- shmobile change of binding for their GIC (using arm,pl390 now)
- ARCH_RENESAS introduction
- Misc other renesas updates
There's also a couple of treewide commits from Masahiro Yamada
cleaning up const/__initconst for SMP operation structs and a switch
to using "depends on" instead of if-constructs on most of the Kconfig
platform targets"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
staging: board: armadillo800eva: Use "arm,pl390"
staging: board: kzm9d: Use "arm,pl390"
ARM: shmobile: r8a7778 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: emev2 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: r8a7740 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: r7s72100 dtsi: Use "arm,pl390" for GIC
ARM: use "depends on" for SoC configs instead of "if" after prompt
ARM/clocksource: use automatic DT probing for ux500 PRCMU
ARM: use const and __initconst for smp_operations
ARM: hisi: do not export smp_operations structures
ARM: mvebu: remove unused mach/gpio.h
ARM: shmobile: Remove legacy mach/irqs.h
ARM: shmobile: Introduce ARCH_RENESAS
MAINTAINERS: Remove link to oss.renesas.com which is closed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-urgent ARM SoC fixes from Olof Johansson:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc.
- MAINTAINERS updates to add a list for brcmstb and fix a typo
- A handful of fixes for OMAP 81xx, a recently resurrected platform
so these can't be considered real regressions and thus got queued.
- A couple of other small fixes for scoop, sa1100 and davinci"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: Fix randconfig build warning for dm814_pllss_data
ARM: sa1100/simpad: Be sure to clamp return value
ARM: scoop: Be sure to clamp return value
ARM: davinci: fix a problematic usage of WARN()
ARM: davinci: only select WT cache if cache is enabled
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
MAINTAINERS: gpio-brcmstb: Remove stray '>'
MAINTAINERS: brcmstb: Include Broadcom internal mailing-list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"The asm-generic tree this time contains one series from Nicolas Pitre
that makes the optimized do_div() implementation from the ARM
architecture available to all architectures.
This also adds stricter type checking for callers of do_div, which has
uncovered a number of bugs in existing code, and fixes up the ones we
have found"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
ARM: asm/div64.h: adjust to generic codde
__div64_32(): make it overridable at compile time
__div64_const32(): abstract out the actual 128-bit cross product code
do_div(): generic optimization for constant divisor on 32-bit machines
div64.h: optimize do_div() for power-of-two constant divisors
mtd/sm_ftl.c: fix wrong do_div() usage
drm/mgag200/mgag200_mode.c: fix wrong do_div() usage
hid-sensor-hub.c: fix wrong do_div() usage
ti/fapll: fix wrong do_div() usage
ti/clkt_dpll: fix wrong do_div() usage
tegra/clk-divider: fix wrong do_div() usage
imx/clk-pllv2: fix wrong do_div() usage
imx/clk-pllv1: fix wrong do_div() usage
nouveau/nvkm/subdev/clk/gk20a.c: fix wrong do_div() usage
|
|
This wasn't an asm-generic header to start with, and can be merged into
dma-mapping.h trivially.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.
[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We'll soon merge <asm-generic/dma-mapping-common.h> into
<linux/dma-mapping.h> and the reference to dma_capable in the tile
dma_set_mask would create a circular dependency.
Fix this by moving the implementation out of line.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sparc already uses the same code as the generic code for the PCI
implementation but just fails the call sbus. This moves to the generic
implemenation which eventually return -EIO due to the NULL dma_mask
pointer in the device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
[dan.carpenter@oracle.com: C6X: fix build breakage]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
[vgupta@synopsys.com: ARC: dma mapping fixes #2]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Carlos Palminha <CARLOS.PALMINHA@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This series converts all remaining architectures to use dma_map_ops and
the generic implementation of the DMA API. This not only simplifies the
code a lot, but also prepares for possible future changes like more
generic non-iommu dma_ops implementations or generic per-device
dma_map_ops.
This patch (of 16):
We have a couple architectures that do not want to support this code, so
add another Kconfig symbol that disables the code similar to what we do
for the nommu case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This hooks up UBSAN support for PowerPC.
So far it's found some interesting cases where we don't properly sanitise
input to shifts, including one in our futex handling. Nothing critical,
but interesting and worth fixing.
[valentinrothberg@gmail.com: arch/powerpc/Kconfig: fix typo in select statement]
Signed-off-by: Daniel Axtens <dja@axtens.net>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
UBSAN uses compile-time instrumentation to catch undefined behavior
(UB). Compiler inserts code that perform certain kinds of checks before
operations that could cause UB. If check fails (i.e. UB detected)
__ubsan_handle_* function called to print error message.
So the most of the work is done by compiler. This patch just implements
ubsan handlers printing errors.
GCC has this capability since 4.9.x [1] (see -fsanitize=undefined
option and its suboptions).
However GCC 5.x has more checkers implemented [2].
Article [3] has a bit more details about UBSAN in the GCC.
[1] - https://gcc.gnu.org/onlinedocs/gcc-4.9.0/gcc/Debugging-Options.html
[2] - https://gcc.gnu.org/onlinedocs/gcc/Debugging-Options.html
[3] - http://developerblog.redhat.com/2014/10/16/gcc-undefined-behavior-sanitizer-ubsan/
Issues which UBSAN has found thus far are:
Found bugs:
* out-of-bounds access - 97840cb67ff5 ("netfilter: nfnetlink: fix
insufficient validation in nfnetlink_bind")
undefined shifts:
* d48458d4a768 ("jbd2: use a better hash function for the revoke
table")
* 10632008b9e1 ("clockevents: Prevent shift out of bounds")
* 'x << -1' shift in ext4 -
http://lkml.kernel.org/r/<5444EF21.8020501@samsung.com>
* undefined rol32(0) -
http://lkml.kernel.org/r/<1449198241-20654-1-git-send-email-sasha.levin@oracle.com>
* undefined dirty_ratelimit calculation -
http://lkml.kernel.org/r/<566594E2.3050306@odin.com>
* undefined roundown_pow_of_two(0) -
http://lkml.kernel.org/r/<1449156616-11474-1-git-send-email-sasha.levin@oracle.com>
* [WONTFIX] undefined shift in __bpf_prog_run -
http://lkml.kernel.org/r/<CACT4Y+ZxoR3UjLgcNdUm4fECLMx2VdtfrENMtRRCdgHB2n0bJA@mail.gmail.com>
WONTFIX here because it should be fixed in bpf program, not in kernel.
signed overflows:
* 32a8df4e0b33f ("sched: Fix odd values in effective_load()
calculations")
* mul overflow in ntp -
http://lkml.kernel.org/r/<1449175608-1146-1-git-send-email-sasha.levin@oracle.com>
* incorrect conversion into rtc_time in rtc_time64_to_tm() -
http://lkml.kernel.org/r/<1449187944-11730-1-git-send-email-sasha.levin@oracle.com>
* unvalidated timespec in io_getevents() -
http://lkml.kernel.org/r/<CACT4Y+bBxVYLQ6LtOKrKtnLthqLHcw-BMp3aqP3mjdAvr9FULQ@mail.gmail.com>
* [NOTABUG] signed overflow in ktime_add_safe() -
http://lkml.kernel.org/r/<CACT4Y+aJ4muRnWxsUe1CMnA6P8nooO33kwG-c8YZg=0Xc8rJqw@mail.gmail.com>
[akpm@linux-foundation.org: fix unused local warning]
[akpm@linux-foundation.org: fix __int128 build woes]
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yury Gribov <y.gribov@samsung.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Kostya Serebryany <kcc@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move the stuff currently only used by the kexec file code within
CONFIG_KEXEC_FILE (and CONFIG_KEXEC_VERIFY_SIG).
Also move internal "struct kexec_sha_region" and "struct kexec_buf" into
"kexec_internal.h".
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The four cpumasks cpu_{possible,online,present,active}_bits are exposed
readonly via the corresponding const variables cpu_xyz_mask. But they are
also accessible for arbitrary writing via the exposed functions
set_cpu_xyz. There's quite a bit of code throughout the kernel which
iterates over or otherwise accesses these bitmaps, and having the access
go via the cpu_xyz_mask variables is nowadays [1] simply a useless
indirection.
It may be that any problem in CS can be solved by an extra level of
indirection, but that doesn't mean every extra indirection solves a
problem. In this case, it even necessitates some minor ugliness (see
4/6).
Patch 1/6 is new in v2, and fixes a build failure on ppc by renaming a
struct member, to avoid problems when the identifier cpu_online_mask
becomes a macro later in the series. The next four patches eliminate the
cpu_xyz_mask variables by simply exposing the actual bitmaps, after
renaming them to discourage direct access - that still happens through
cpu_xyz_mask, which are now simply macros with the same type and value as
they used to have.
After that, there's no longer any reason to have the setter functions be
out-of-line: The boolean parameter is almost always a literal true or
false, so by making them static inlines they will usually compile to one
or two instructions.
For a defconfig build on x86_64, bloat-o-meter says we save ~3000 bytes.
We also save a little stack (stackdelta says 127 functions have a 16 byte
smaller stack frame, while two grow by that amount). Mostly because, when
iterating over the mask, gcc typically loads the value of cpu_xyz_mask
into a callee-saved register and from there into %rdi before each
find_next_bit call - now it can just load the appropriate immediate
address into %rdi before each call.
[1] See Rusty's kind explanation
http://thread.gmane.org/gmane.linux.kernel/2047078/focus=2047722 for
some historic context.
This patch (of 6):
As preparation for eliminating the indirect access to the various global
cpu_*_bits bitmaps via the pointer variables cpu_*_mask, rename the
cpu_online_mask member of struct fadump_crash_info_header to simply
online_mask, thus allowing cpu_online_mask to become a macro.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
