| Age | Commit message (Collapse) | Author |
|---|
|
The way we handle include paths for DT has changed a bit, which
broke a file that had an unconventional way to reference a common
header file:
arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts:47:10: fatal error: include/dt-bindings/input/linux-event-codes.h: No such file or directory
This removes the leading "include/" from the path name, which fixes it.
Fixes: d5d332d3f7e8 ("devicetree: Move include prefixes from arch to separate directory")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
gcc-7 warns about some declarations that are more 'const' than necessary:
arch/arm/mach-at91/pm.c:338:34: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const struct of_device_id const ramc_ids[] __initconst = {
arch/arm/mach-bcm/bcm_kona_smc.c:36:34: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const struct of_device_id const bcm_kona_smc_ids[] __initconst = {
arch/arm/mach-spear/time.c:207:34: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const struct of_device_id const timer_of_match[] __initconst = {
arch/arm/mach-omap2/prm_common.c:714:34: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const struct of_device_id const omap_prcm_dt_match_table[] __initconst = {
arch/arm/mach-omap2/vc.c:562:35: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const struct i2c_init_data const omap4_i2c_timing_data[] __initconst = {
The ones in arch/arm were apparently all introduced accidentally by one
commit that correctly marked a lot of variables as __initconst.
Fixes: 19c233b79d1a ("ARM: appropriate __init annotation for const data")
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.12-rc cycle most consisting of few minor dts fixes
for various devices. Also included is a memory controller (GPMC) debug output
fix as without that the shown bootloader configured GPMC bus width will
be wrong and won't work for kernel timings:
- Add dra7 powerhold configuration to be able to shut down pmic correctly
- Fix polarity for gta04 mcbsp4 clocks for modem
- Fix Pandaboard CEC pin pull making it usable
- Fix LogicPD Torpedo camera pin mux
- Fix GPMC debug bus width
- Reduce cpu thermal shutdown temperature
* tag 'omap-for-v4.12/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7: Reduce cpu thermal shutdown temperature
memory: omap-gpmc: Fix debug output for access width
ARM: dts: LogicPD Torpedo: Fix camera pin mux
ARM: dts: omap4: enable CEC pin for Pandaboard A4 and ES
ARM: dts: gta04: fix polarity of clocks for mcbsp4
ARM: dts: dra7: Add power hold and power controller properties to palmas
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.12:
- A fix on GPCv2 power domain driver Kconfig which causes a build
failure when CONFIG_PM is not set.
- Pull down PMIC IRQ pin for imx53-qsrb board to prevent spurious
PMIC interrupts from happening.
- Remove board level OPP override for imx6sx-sdb to fix a boot crash
seen on Rev.C boards.
* tag 'imx-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: add PM dependency for IMX7_PM_DOMAINS
ARM: dts: imx6sx-sdb: Remove OPP override
ARM: dts: imx53-qsrb: Pulldown PMIC IRQ pin
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Enable Qualcomm drivers needed to boot Dragonboard 410c with HDMI. This
enables support for clocks, regulators, and USB PHY.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
[Olof: Turned off _RPM configs per follow-up email]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Sync the defconfig with savedefconfig as config options change/move over
time.
Generated with the following commands:
make defconfig
make savedefconfig
cp defconfig arch/arm64/configs/defconfig
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
It makes sense to have a stripped-down defconfig for just Gemini, as
it is a pretty small platform used in NAS etc, and will use appended
device tree. It is also quick to compile and test. Hopefully this
defconfig can be a good base for distributions such as OpenWRT.
I plan to add in the config options needed for the different
variants of Gemini as we go along.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for
4.12, please pull the following:
- Baruch provides several fixes for the Raspberry Pi (BCM2835) Device
Tree source include file: uart0 pinctrl node names, pin number for
i2c0, uart0 rts/cts pins and invalid uart1 pin, missing numbers for
ethernet aliases
* tag 'arm-soc/for-4.12/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm2835: add index to the ethernet alias
ARM: dts: bcm2835: fix uart0/uart1 pins
ARM: dts: bcm2835: fix i2c0 pins
ARM: dts: bcm2835: fix uart0 pinctrl node names
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
We use a directory under arch/$ARCH/boot/dts as an include path
that has links outside of the subtree to find dt-bindings from under
include/dt-bindings. That's been working well, but new DT architectures
haven't been adding them by default.
Recently there's been a desire to share some of the DT material between
arm and arm64, which originally caused developers to create symlinks or
relative includes between the subtrees. This isn't ideal -- it breaks
if the DT files aren't stored in the exact same hierarchy as the kernel
tree, and generally it's just icky.
As a somewhat cleaner solution we decided to add a $ARCH/ prefix link
once, and allow DTS files to reference dtsi (and dts) files in other
architectures that way.
Original approach was to create these links under each architecture,
but it lead to the problem of recursive symlinks.
As a remedy, move the include link directories out of the architecture
trees into a common location. At the same time, they can now share one
directory and one dt-bindings/ link as well.
Fixes: 4027494ae6e3 ('ARM: dts: add arm/arm64 include symlinks')
Reported-by: Russell King <linux@armlinux.org.uk>
Reported-by: Omar Sandoval <osandov@osandov.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: linux-arch <linux-arch@vger.kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
We've received a few fixes branches with -rc1 as base, but our contents was
still at pre-rc1. Merge it in expliticly to make 'git merge --log' clear on
hat was actually merged.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
xen_flush_tlb_all() is used in arch/x86/xen/mmu.c only. Make it static.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
There are some leftovers testing for pvh guest mode in pv-only source
files. Remove them.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
virt_addr_valid() is supposed to tell you if it's OK to call virt_to_page() on
an address. What this means in practice is that it should only return true for
addresses in the linear mapping which are backed by a valid PFN.
We are failing to properly check that the address is in the linear mapping,
because virt_to_pfn() will return a valid looking PFN for more or less any
address. That bug is actually caused by __pa(), used in virt_to_pfn().
eg: __pa(0xc000000000010000) = 0x10000 # Good
__pa(0xd000000000010000) = 0x10000 # Bad!
__pa(0x0000000000010000) = 0x10000 # Bad!
This started happening after commit bdbc29c19b26 ("powerpc: Work around gcc
miscompilation of __pa() on 64-bit") (Aug 2013), where we changed the definition
of __pa() to work around a GCC bug. Prior to that we subtracted PAGE_OFFSET from
the value passed to __pa(), meaning __pa() of a 0xd or 0x0 address would give
you something bogus back.
Until we can verify if that GCC bug is no longer an issue, or come up with
another solution, this commit does the minimal fix to make virt_addr_valid()
work, by explicitly checking that the address is in the linear mapping region.
Fixes: bdbc29c19b26 ("powerpc: Work around gcc miscompilation of __pa() on 64-bit")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Tested-by: Breno Leitao <breno.leitao@gmail.com>
|
|
Smatch complains that we check cap the upper bound of "index" but don't
check for negatives. It's a false positive because "index" is never
negative. But it's also simple enough to make it unsigned which makes
the code easier to audit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
KVM/ARM Fixes for v4.12-rc2.
Includes:
- A fix for a build failure introduced in -rc1 when tracepoints are
enabled on 32-bit ARM.
- Disabling use of stack pointer protection in the hyp code which can
cause panics.
- A handful of VGIC fixes.
- A fix to the init of the redistributors on GICv3 systems that
prevented boot with kvmtool on GICv3 systems introduced in -rc1.
- A number of race conditions fixed in our MMU handling code.
- A fix for the guest being able to program the debug extensions for
the host on the 32-bit side.
|
|
The ftrace function_graph time measurements of a given function is not
accurate according to those recorded by ftrace using the function
filters. This change pulls the x86_64 fix from 'commit 722b3c746953
("ftrace/graph: Trace function entry before updating index")' into the
sparc specific prepare_ftrace_return which stops ftrace from
counting interrupted tasks in the time measurement.
Example measurements for select_task_rq_fair running "hackbench 100
process 1000":
| tracing/trace_stat/function0 | function_graph
Before patch | 2.802 us | 4.255 us
After patch | 2.749 us | 3.094 us
Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Greetings,
GCC 7 introduced the -Wstringop-overflow flag to detect buffer overflows
in calls to string handling functions [1][2]. Due to the way
``empty_zero_page'' is declared in arch/sparc/include/setup.h, this
causes a warning to trigger at compile time in the function mem_init(),
which is subsequently converted to an error. The ensuing patch fixes
this issue and aligns the declaration of empty_zero_page to that of
other architectures. Thank you.
Cheers,
Orlando.
[1] https://gcc.gnu.org/ml/gcc-patches/2016-10/msg02308.html
[2] https://gcc.gnu.org/gcc-7/changes.html
Signed-off-by: Orlando Arias <oarias@knights.ucf.edu>
--------------------------------------------------------------------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An incorrect huge page alignment check caused
mmap failure for 64K pages when MAP_FIXED is used
with address not aligned to HPAGE_SIZE.
Orabug: 25885991
Fixes: dcd1912d21a0 ("sparc64: Add 64K page size support")
Signed-off-by: Nitin Gupta <nitin.m.gupta@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, cpus_set_cap() calls static_branch_enable_cpuslocked(), which
must take the jump_label mutex.
We call cpus_set_cap() in the secondary bringup path, from the idle
thread where interrupts are disabled. Taking a mutex in this path "is a
NONO" regardless of whether it's contended, and something we must avoid.
We didn't spot this until recently, as ___might_sleep() won't warn for
this case until all CPUs have been brought up.
This patch avoids taking the mutex in the secondary bringup path. The
poking of static keys is deferred until enable_cpu_capabilities(), which
runs in a suitable context on the boot CPU. To account for the static
keys being set later, cpus_have_const_cap() is updated to use another
static key to check whether the const cap keys have been initialised,
falling back to the caps bitmap until this is the case.
This means that users of cpus_have_const_cap() gain should only gain a
single additional NOP in the fast path once the const caps are
initialised, but should always see the current cap value.
The hyp code should never dereference the caps array, since the caps are
initialized before we run the module initcall to initialise hyp. A check
is added to the hyp init code to document this requirement.
This change will sidestep a number of issues when the upcoming hotplug
locking rework is merged.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyniger <marc.zyngier@arm.com>
Reviewed-by: Suzuki Poulose <suzuki.poulose@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Sewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
On dra7, as per TRM, the HW shutdown (TSHUT) temperature is hardcoded
to 123C and cannot be modified by SW. This means when the temperature
reaches 123C HW asserts TSHUT output which signals a warm reset.
This reset is held until the temperature goes below the TSHUT low (105C).
While in SW, the thermal driver continuously monitors current temperature
and takes decisions based on whether it reached an alert or a critical point.
The intention of setting a SW critical point is to prevent force reset by HW
and instead do an orderly_poweroff(). But if the SW critical temperature is
greater than or equal to that of HW then it defeats the purpose. To address
this and let SW take action before HW does keep the SW critical temperature
less than HW TSHUT value.
The value for SW critical temperature was chosen as 120C just to ensure
we give SW sometime before HW catches up.
Document reference
SPRUI30C – DRA75x, DRA74x Technical Reference Manual - November 2016
SPRUHZ6H - AM572x Technical Reference Manual - November 2016
Tested on:
DRA75x PG 2.0 Rev H EVM
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For most cases a protection exception in the host (e.g. copy
on write or dirty tracking) on the sie instruction will indicate
an instruction length of 4. Turns out that there are some corner
cases (e.g. runtime instrumentation) where this is not necessarily
true and the ILC is unpredictable.
Let's replace our 4 byte rewind_pad with 3 byte nops to prepare for
all possible ILCs.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
'davinci_pm_init'
It is wrong to iounmap resources in the normal path of davinci_pm_init()
The 3 ioremap'ed fields of 'pm_config' can be accessed later on in other
functions, so we should return 'success' instead of unrolling everything.
Fixes: aa9aa1ec2df6 ("ARM: davinci: PM: rework init, remove platform device")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[nsekhar@ti.com: commit message and minor style fixes]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
If 'sram_alloc' fails, we need to free already allocated resources.
Fixes: aa9aa1ec2df6 ("ARM: davinci: PM: rework init, remove platform device")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The page table dump code doesn't know about huge pages, so currently
it crashes (or walks random memory, usually leading to a crash), if it
finds a huge page. On Book3S we only see huge pages in the Linux page
tables when we're using the P9 Radix MMU.
Teaching the code to properly handle huge pages is a bit more involved,
so for now just prevent the crash.
Cc: stable@vger.kernel.org # v4.10+
Fixes: 8eb07b187000 ("powerpc/mm: Dump linux pagetables")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In some fio benchmarks, halt_poll_ns=400000 caused CPU utilization to
increase heavily even in cases where the performance improvement was
small. In particular, bandwidth divided by CPU usage was as much as
60% lower.
To some extent this is the expected effect of the patch, and the
additional CPU utilization is only visible when running the
benchmarks. However, halving the threshold also halves the extra
CPU utilization (from +30-130% to +20-70%) and has no negative
effect on performance.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
- convert the debug feature to refcount_t
- reduce the copy size for strncpy_from_user
- 8 bug fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/virtio: change virtio_feature_desc:features type to __le32
s390: convert debug_info.ref_count from atomic_t to refcount_t
s390: move _text symbol to address higher than zero
s390/qdio: increase string buffer size
s390/ccwgroup: increase string buffer size
s390/topology: let topology_mnest_limit() return unsigned char
s390/uaccess: use sane length for __strncpy_from_user()
s390/uprobes: fix compile for !KPROBES
s390/ftrace: fix compile for !MODULES
s390/cputime: fix incorrect system time
|
|
Fix commit 05c4ffc3a266 ("ARM: dts: LogicPD Torpedo: Add MT9P031 Support")
In the previous commit, I indicated that the only testing was done by
showing the camera showed up when probing. This patch fixes an incorrect
pin muxing on cam_d0, cam_d1 and cam_d2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The CEC pin was always pulled up, making it impossible to use it.
Change to PIN_INPUT so it can be used by the new CEC support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The clock polarity setting of the mcbsp connected to
the modem was wrong so almost only noise
was received.
With this patch it is also the same as it was on
earlier non-dt kernels where it was working properly
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add power hold and power controller properties to palmas node.
This is needed to shutdown pmic correctly on boards with
powerhold set.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 22d8b3dec214c ("powerpc/kprobes: Emulate instructions on kprobe
handler re-entry") enabled emulating instructions on kprobe re-entry,
rather than single-stepping always. However, we didn't update the single
stepping code to only be run if the emulation fails. Also, we missed
re-enabling preemption if the instruction emulation was successful. Fix
those issues.
Fixes: 22d8b3dec214c ("powerpc/kprobes: Emulate instructions on kprobe handler re-entry")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Commit 17ed4c8f81da ("powerpc/powernv: Recover correct PACA on wakeup
from a stop on P9 DD1") promises to set the NAPSTATELOST bit in paca
after recovering the correct paca for the thread waking up from stop1
on DD1, so that the GPRs can be correctly restored on the stop exit
path. However, it loads the value 1 into r3, but stores the value in
r0 into NAPSTATELOST(r13).
Fix this by correctly set the NAPSTATELOST bit in paca after
recovering the paca on POWER9 DD1.
Fixes: 17ed4c8f81da ("powerpc/powernv: Recover correct PACA on wakeup from a stop on P9 DD1")
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Pull networking fixes from David Miller:
1) Track alignment in BPF verifier so that legitimate programs won't be
rejected on !CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS architectures.
2) Make tail calls work properly in arm64 BPF JIT, from Deniel
Borkmann.
3) Make the configuration and semantics Generic XDP make more sense and
don't allow both generic XDP and a driver specific instance to be
active at the same time. Also from Daniel.
4) Don't crash on resume in xen-netfront, from Vitaly Kuznetsov.
5) Fix use-after-free in VRF driver, from Gao Feng.
6) Use netdev_alloc_skb_ip_align() to avoid unaligned IP headers in
qca_spi driver, from Stefan Wahren.
7) Always run cleanup routines in BPF samples when we get SIGTERM, from
Andy Gospodarek.
8) The mdio phy code should bring PHYs out of reset using the shared
GPIO lines before invoking bus->reset(). From Florian Fainelli.
9) Some USB descriptor access endian fixes in various drivers from
Johan Hovold.
10) Handle PAUSE advertisements properly in mlx5 driver, from Gal
Pressman.
11) Fix reversed test in mlx5e_setup_tc(), from Saeed Mahameed.
12) Cure netdev leak in AF_PACKET when using timestamping via control
messages. From Douglas Caetano dos Santos.
13) netcp doesn't support HWTSTAMP_FILTER_ALl, reject it. From Miroslav
Lichvar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
ldmvsw: stop the clean timer at beginning of remove
ldmvsw: unregistering netdev before disable hardware
net: netcp: fix check of requested timestamping filter
ipv6: avoid dad-failures for addresses with NODAD
qed: Fix uninitialized data in aRFS infrastructure
mdio: mux: fix device_node_continue.cocci warnings
net/packet: fix missing net_device reference release
net/mlx4_core: Use min3 to select number of MSI-X vectors
macvlan: Fix performance issues with vlan tagged packets
net: stmmac: use correct pointer when printing normal descriptor ring
net/mlx5: Use underlay QPN from the root name space
net/mlx5e: IPoIB, Only support regular RQ for now
net/mlx5e: Fix setup TC ndo
net/mlx5e: Fix ethtool pause support and advertise reporting
net/mlx5e: Use the correct pause values for ethtool advertising
vmxnet3: ensure that adapter is in proper state during force_close
sfc: revert changes to NIC revision numbers
net: ch9200: add missing USB-descriptor endianness conversions
net: irda: irda-usb: fix firmware name on big-endian hosts
net: dsa: mv88e6xxx: add default case to switch
...
|
|
The Raspberry Pi startup stub files for multi-core BCM283X processors
make the secondary CPUs spin until the corresponding mailbox is
written. These stubs are loaded at physical address 0x00000xxx (as seen
by the ARMs), but this page will be reused by the kernel unless it is
explicitly reserved, causing the waiting cores to execute random code.
Use the /memreserve/ Device Tree directive to mark the first page as
off-limits to the kernel.
See: https://github.com/raspberrypi/linux/issues/1989
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
commit d98ecdaca296 ("arm64: perf: Count EL2 events if the kernel is
running in HYP") returns -EINVAL when perf system call perf_event_open is
called with exclude_hv != exclude_kernel. This change breaks applications
on VHE enabled ARMv8.1 platforms. The issue was observed with HHVM
application, which calls perf_event_open with exclude_hv = 1 and
exclude_kernel = 0.
There is no separate hypervisor privilege level when VHE is enabled, the
host kernel runs at EL2. So when VHE is enabled, we should ignore
exclude_hv from the application. This behaviour is consistent with PowerPC
where the exclude_hv is ignored when the hypervisor is not present and with
x86 where this flag is ignored.
Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
[will: added comment to justify the behaviour of exclude_hv]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The cmpxchg implementation introduced by commit c342f78217e8 ("arm64:
cmpxchg: patch in lse instructions when supported by the CPU") performs
an apparently redundant register move of [old] to [oldval] in the
success case - it always uses the same register width as [oldval] was
originally loaded with, and is only executed when [old] and [oldval] are
known to be equal anyway.
The only effect it seemingly does have is to take up a surprising amount
of space in the kernel text, as removing it reveals:
text data bss dec hex filename
12426658 1348614 4499749 18275021 116dacd vmlinux.o.new
12429238 1348614 4499749 18277601 116e4e1 vmlinux.o.old
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This fixes the new ept_access_test_read_only and ept_access_test_read_write
testcases from vmx.flat.
The problem is that gpte_access moves bits around to switch from EPT
bit order (XWR) to ACC_*_MASK bit order (RWX). This results in an
incorrect exit qualification. To fix this, make pt_access and
pte_access operate on raw PTE values (only with NX flipped to mean
"can execute") and call gpte_access at the end of the walk. This
lets us use pte_access to compute the exit qualification with XWR
bit order.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
We can observe eptad kvm_intel module parameter is still Y
even if ept is disabled which is weird. This patch will
not enable EPT A/D feature if EPT feature is disabled.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Reported by syzkaller:
BUG: unable to handle kernel paging request at ffffffffc07f6a2e
IP: report_bug+0x94/0x120
PGD 348e12067
P4D 348e12067
PUD 348e14067
PMD 3cbd84067
PTE 80000003f7e87161
Oops: 0003 [#1] SMP
CPU: 2 PID: 7091 Comm: kvm_load_guest_ Tainted: G OE 4.11.0+ #8
task: ffff92fdfb525400 task.stack: ffffbda6c3d04000
RIP: 0010:report_bug+0x94/0x120
RSP: 0018:ffffbda6c3d07b20 EFLAGS: 00010202
do_trap+0x156/0x170
do_error_trap+0xa3/0x170
? kvm_load_guest_fpu.part.175+0x12a/0x170 [kvm]
? mark_held_locks+0x79/0xa0
? retint_kernel+0x10/0x10
? trace_hardirqs_off_thunk+0x1a/0x1c
do_invalid_op+0x20/0x30
invalid_op+0x1e/0x30
RIP: 0010:kvm_load_guest_fpu.part.175+0x12a/0x170 [kvm]
? kvm_load_guest_fpu.part.175+0x1c/0x170 [kvm]
kvm_arch_vcpu_ioctl_run+0xed6/0x1b70 [kvm]
kvm_vcpu_ioctl+0x384/0x780 [kvm]
? kvm_vcpu_ioctl+0x384/0x780 [kvm]
? sched_clock+0x13/0x20
? __do_page_fault+0x2a0/0x550
do_vfs_ioctl+0xa4/0x700
? up_read+0x1f/0x40
? __do_page_fault+0x2a0/0x550
SyS_ioctl+0x79/0x90
entry_SYSCALL_64_fastpath+0x23/0xc2
SDM mentioned that "The MXCSR has several reserved bits, and attempting to write
a 1 to any of these bits will cause a general-protection exception(#GP) to be
generated". The syzkaller forks' testcase overrides xsave area w/ random values
and steps on the reserved bits of MXCSR register. The damaged MXCSR register
values of guest will be restored to SSEx MXCSR register before vmentry. This
patch fixes it by catching userspace override MXCSR register reserved bits w/
random values and bails out immediately.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
There are PML_ENTITY_NUM elements in the pml_address[] array so the >
should be >= or we write beyond the end of the array when we do:
pml_address[vmcs12->guest_pml_index--] = gpa;
Fixes: c5f983f6e845 ("nVMX: Implement emulated Page Modification Logging")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
- fix build failures with PR KVM configurations
- fix a host crash that can occur on POWER9 with radix guests
|
|
pm_fake doesn't quite describe what the handler does (ignoring writes
and returning 0 for reads).
As we're about to use it (a lot) in a different context, rename it
with a (admitedly cryptic) name that make sense for all users.
Signed-off-by: Zhichao Huang <zhichao.huang@linaro.org>
Reviewed-by: Alex Bennee <alex.bennee@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
|
|
Hardware debugging in guests is not intercepted currently, it means
that a malicious guest can bring down the entire machine by writing
to the debug registers.
This patch enable trapping of all debug registers, preventing the
guests to access the debug registers. This includes access to the
debug mode(DBGDSCR) in the guest world all the time which could
otherwise mess with the host state. Reads return 0 and writes are
ignored (RAZ_WI).
The result is the guest cannot detect any working hardware based debug
support. As debug exceptions are still routed to the guest normal
debug using software based breakpoints still works.
To support debugging using hardware registers we need to implement a
debug register aware world switch as well as special trapping for
registers that may affect the host state.
Cc: stable@vger.kernel.org
Signed-off-by: Zhichao Huang <zhichao.huang@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
|
|
In commit dc3106690b20 ("powerpc: tm: Always use fp_state and vr_state
to store live registers"), a section of code was removed that copied
the current state to checkpointed state. That code should not have been
removed.
When an FP (Floating Point) unavailable is taken inside a transaction,
we need to abort the transaction. This is because at the time of the
tbegin, the FP state is bogus so the state stored in the checkpointed
registers is incorrect. To fix this, we treclaim (to get the
checkpointed GPRs) and then copy the thread_struct FP live state into
the checkpointed state. We then trecheckpoint so that the FP state is
correctly restored into the CPU.
The copying of the FP registers from live to checkpointed is what was
missing.
This simplifies the logic slightly from the original patch.
tm_reclaim_thread() will now always write the checkpointed FP
state. Either the checkpointed FP state will be written as part of
the actual treclaim (in tm.S), or it'll be a copy of the live
state. Which one we use is based on MSR[FP] from userspace.
Similarly for VMX.
Fixes: dc3106690b20 ("powerpc: tm: Always use fp_state and vr_state to store live registers")
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: cyrilbur@gmail.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We like living dangerously. Nothing explicitely forbids stack-protector
to be used in the HYP code, while distributions routinely compile their
kernel with it. We're just lucky that no code actually triggers the
instrumentation.
Let's not try our luck for much longer, and disable stack-protector
for code living at HYP.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
|
|
On powerpc we can build the kernel with two different ABIs for mcount(), which
is used by ftrace. Kernels built with one ABI do not know how to load modules
built with the other ABI. The new style ABI is called "mprofile-kernel", for
want of a better name.
Currently if we build a module using the old style ABI, and the kernel with
mprofile-kernel, when we load the module we'll oops something like:
# insmod autofs4-no-mprofile-kernel.ko
ftrace-powerpc: Unexpected instruction f8810028 around bl _mcount
------------[ cut here ]------------
WARNING: CPU: 6 PID: 3759 at ../kernel/trace/ftrace.c:2024 ftrace_bug+0x2b8/0x3c0
CPU: 6 PID: 3759 Comm: insmod Not tainted 4.11.0-rc3-gcc-5.4.1-00017-g5a61ef74f269 #11
...
NIP [c0000000001eaa48] ftrace_bug+0x2b8/0x3c0
LR [c0000000001eaff8] ftrace_process_locs+0x4a8/0x590
Call Trace:
alloc_pages_current+0xc4/0x1d0 (unreliable)
ftrace_process_locs+0x4a8/0x590
load_module+0x1c8c/0x28f0
SyS_finit_module+0x110/0x140
system_call+0x38/0xfc
...
ftrace failed to modify
[<d000000002a31024>] 0xd000000002a31024
actual: 35:65:00:48
We can avoid this by including in the vermagic whether the kernel/module was
built with mprofile-kernel. Which results in:
# insmod autofs4-pg.ko
autofs4: version magic
'4.11.0-rc3-gcc-5.4.1-00017-g5a61ef74f269 SMP mod_unload modversions '
should be
'4.11.0-rc3-gcc-5.4.1-00017-g5a61ef74f269-dirty SMP mod_unload modversions mprofile-kernel'
insmod: ERROR: could not insert module autofs4-pg.ko: Invalid module format
Fixes: 8c50b72a3b4f ("powerpc/ftrace: Add Kconfig & Make glue for mprofile-kernel")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Jessica Yu <jeyu@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We like living dangerously. Nothing explicitely forbids stack-protector
to be used in the EL2 code, while distributions routinely compile their
kernel with it. We're just lucky that no code actually triggers the
instrumentation.
Let's not try our luck for much longer, and disable stack-protector
for code living at EL2.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
|
|
Moving most of the shared code to virt/kvm/arm had for consequence
that KVM/ARM doesn't build anymore, because the code that used to
define the tracepoints is now somewhere else.
Fix this by defining CREATE_TRACE_POINTS in coproc.c, and clean-up
trace.h as well.
Fixes: 35d2d5d490e2 ("KVM: arm/arm64: Move shared files to virt/kvm/arm")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
|
|
The board file for imx6sx-sdb overrides cpufreq operating points to use
higher voltages. This is done because the board has a shared rail for
VDD_ARM_IN and VDD_SOC_IN and when using LDO bypass the shared voltage
needs to be a value suitable for both ARM and SOC.
This only applies to LDO bypass mode, a feature not present in upstream.
When LDOs are enabled the effect is to use higher voltages than necessary
for no good reason.
Setting these higher voltages can make some boards fail to boot with ugly
semi-random crashes reminiscent of memory corruption. These failures only
happen on board rev. C, rev. B is reported to still work.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 54183bd7f766 ("ARM: imx6sx-sdb: add revb board and make it default")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently the following errors are seen:
[ 14.015056] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 27.321093] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 27.411681] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 27.456281] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 30.527106] mc13xxx 0-0008: Failed to read IRQ status: -6
[ 36.596900] mc13xxx 0-0008: Failed to read IRQ status: -6
Also when reading the interrupts via 'cat /proc/interrupts' the
PMIC GPIO interrupt counter does not stop increasing.
The reason for the storm of interrupts is that the PUS field of
register IOMUXC_SW_PAD_CTL_PAD_CSI0_DAT5 is currently configured as:
10 : 100k pullup
and the PMIC interrupt is being registered as IRQ_TYPE_LEVEL_HIGH type,
which is the correct type as per the MC34708 datasheet.
Use the default power on value for the IOMUX, which sets PUS field as:
00: 360k pull down
This prevents the spurious PMIC interrupts from happening.
Commit e1ffceb078c6 ("ARM: imx53: qsrb: fix PMIC interrupt level")
correctly described the irq type as IRQ_TYPE_LEVEL_HIGH, but
missed to update the IOMUX of the PMIC GPIO as pull down.
Fixes: e1ffceb078c6 ("ARM: imx53: qsrb: fix PMIC interrupt level")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
