| Age | Commit message (Collapse) | Author |
|---|
|
Code patching for the dynamically enabled shadow call stack comes down
to finding PACIASP and AUTIASP instructions -which behave as NOPs on
cores that do not implement pointer authentication- and converting them
into shadow call stack pushes and pops, respectively.
Due to past bad experiences with the highly complex and overengineered
DWARF standard that describes the unwind metadata that we are using to
locate these instructions, let's make this patching logic a little bit
more robust so that any issues with the unwind metadata detected at boot
time can de dealt with gracefully.
The DWARF annotations that are used for this are emitted at function
granularity, and due to the fact that the instructions we are patching
will simply behave as NOPs if left unpatched, we can abort on errors as
long as we don't leave any functions in a half-patched state.
So do a dry run of each FDE frame (covering a single function) before
performing the actual patching, and give up if the DWARF metadata cannot
be understood.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20221213142849.1629026-1-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
- "evailable" -> "available"
Signed-off-by: Prathu Baronia <prathubaronia2011@gmail.com>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/r/20230123110639.10473-1-prathubaronia2011@gmail.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Fix spelling typos in arm64: (reported by codespell)
s/upto/up to/
s/familly/family/
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Will Deacon <will@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20230124181605.14144-1-rdunlap@infradead.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Ensure that the endianness used for populating the ID map matches the
endianness that the running kernel will be using, as this is no longer
guaranteed now that create_idmap() is invoked before init_kernel_el().
Note that doing so is only safe if the MMU is off, as switching the
endianness with the MMU on results in the active ID map to become
invalid. So also clear the M bit when toggling the EE bit in SCTLR, and
mark the MMU as disabled at boot.
Note that the same issue has resulted in preserve_boot_args() recording
the contents of registers X0 ... X3 in the wrong byte order, although
this is arguably a very minor concern.
Fixes: 32b135a7fafe ("arm64: head: avoid cache invalidation when entering with the MMU on")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230125185910.962733-1-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
ALSA SoC has many types of Generic Audio Card drivers (Simple Audio
Card, Audio Graph Card, Audio Graph Card2), and Renesas/Kuninori
Morimoto wants to test these.
The Generic Audio Card driver had been requested on ALSA SoC.
It supports many types of device connection methods, and historically,
the requested connection support range of the generic driver has been
upgraded.
Upgrading the connection support range itself could not be implemented
in the generic driver, because we need to keep compatibility with old
DTBs. This is one of the reasons why we have many types of Generic Audio
Card driver.
The ULCB/KF combo is a good board stack to test these.
Kuninori has been testing these Generic Audio Card drivers by using his
local patches to switching drivers. But from an information sharing
point of view, it is a good idea to upstream these, because the DT
configuration is complex. Hence this can be a good sample for the user.
Hence add a "Simple Audio Card + MIXer + TDM Split" DT setting file for
ULCB/KF. Because of the limited number of subdevices, the HDMI output
is ignored.
This setting can be enabled by updating ulcb.dtsi / ulcb-kf.dtsi.
From a normal user point of view who doesn't need to test the driver,
everything should stay as-is, and nothing changes.
Note that because this needs "switching driver", and not "adding extra
feature", this does not use a Device Tree overlay.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/874jsvi40e.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
ALSA SoC has many types of Generic Audio Card drivers (Simple Audio
Card, Audio Graph Card, Audio Graph Card2), and Renesas/Kuninori
Morimoto wants to test these.
The Generic Audio Card driver had been requested on ALSA SoC.
It supports many types of device connection methods, and historically,
the requested connection support range of the generic driver has been
upgraded.
Upgrading the connection support range itself could not be implemented
in the generic driver, because we need to keep compatibility with old
DTBs. This is one of the reasons why we have many types of Generic Audio
Card driver.
The ULCB/KF combo is a good board stack to test these.
Kuninori has been testing these Generic Audio Card drivers by using his
local patches to switching drivers. But from an information sharing
point of view, it is a good idea to upstream these, because the DT
configuration is complex. Hence this can be a good sample for the user.
Hence add an "Audio Graph Card + MIXer + TDM Split" DT setting file for
ULCB/KF. Because of the limited number of subdevices, the HDMI output
is ignored.
This setting can be enabled by updating ulcb.dtsi / ulcb-kf.dtsi.
From a normal user point of view who doesn't need to test the driver,
everything should stay as-is, and nothing changes.
Note that because this needs "switching driver", and not "adding extra
feature", this does not use a Device Tree overlay.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/875ydbi40l.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
ALSA SoC has many types of Generic Audio Card drivers (Simple Audio
Card, Audio Graph Card, Audio Graph Card2), and Renesas/Kuninori
Morimoto wants to test these.
The Generic Audio Card driver had been requested on ALSA SoC.
It supports many types of device connection methods, and historically,
the requested connection support range of the generic driver has been
upgraded.
Upgrading the connection support range itself could not be implemented
in the generic driver, because we need to keep compatibility with old
DTBs. This is one of the reasons why we have many types of Generic Audio
Card driver.
The ULCB/KF combo is a good board stack to test these.
Kuninori has been testing these Generic Audio Card drivers by using his
local patches to switching drivers. But from an information sharing
point of view, it is a good idea to upstream these, because the DT
configuration is complex. Hence this can be a good sample for the user.
Hence add an "Audio Graph Card2 + MIXer + TDM Split" DT setting file
for ULCB/KF. Because of the limited number of subdevices, the HDMI
output is ignored.
This setting can be enabled by updating ulcb.dtsi / ulcb-kf.dtsi.
From a normal user point of view who doesn't need to test the driver,
everything should stay as-is, and nothing changes.
Note that because this needs "switching driver", and not "adding extra
feature", this does not use a Device Tree overlay.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/877cxri40q.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
ALSA SoC has many types of Generic Audio Card drivers (Simple Audio
Card, Audio Graph Card, Audio Graph Card2), and Renesas/Kuninori
Morimoto wants to test these.
The Generic Audio Card driver had been requested on ALSA SoC.
It supports many types of device connection methods, and historically,
the requested connection support range of the generic driver has been
upgraded.
Upgrading the connection support range itself could not be implemented
in the generic driver, because we need to keep compatibility with old
DTBs. This is one of the reasons why we have many types of Generic Audio
Card driver.
The ULCB/KF combo is a good board stack to test these.
Kuninori has been testing these Generic Audio Card drivers by using his
local patches to switching drivers. But from an information sharing
point of view, it is a good idea to upstream these, because the DT
configuration is complex. Hence this can be a good sample for the user.
Hence add a "Simple Audio Card" DT setting file for ULCB/KF.
This can be enabled by updating ulcb.dtsi / ulcb-kf.dtsi.
From a normal user point of view who doesn't need to test the driver,
everything should stay as-is, and nothing changes.
Note that because this needs "switching driver", and not "adding extra
feature", this does not use a Device Tree overlay.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/878ri7i40u.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
ALSA SoC has many types of Generic Audio Card drivers (Simple Audio
Card, Audio Graph Card, Audio Graph Card2), and Renesas/Kuninori
Morimoto wants to test these.
The Generic Audio Card driver had been requested on ALSA SoC.
It supports many types of device connection methods, and historically,
the requested connection support range of the generic driver has been
upgraded.
Upgrading the connection support range itself could not be implemented
in the generic driver, because we need to keep compatibility with old
DTBs. This is one of the reasons why we have many types of Generic Audio
Card driver.
The ULCB/KF combo is a good board stack to test these.
Kuninori has been testing these Generic Audio Card drivers by using his
local patches to switching drivers. But from an information sharing
point of view, it is a good idea to upstream these, because the DT
configuration is complex. Hence this can be a good sample for the user.
Hence add an "Audio Graph Card2" DT setting file for ULCB/KF,
and switch to use it. You can switch to a different Generic Audio Graph
driver by updating ulcb.dtsi / ulcb-kf.dtsi.
From a normal user point of view who doesn't need to test the driver,
everything should stay as-is, and nothing changes.
Note that because this needs "switching driver", and not "adding extra
feature", this does not use a Device Tree overlay.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87a62ni40z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
ALSA SoC has many types of Generic Audio Card drivers (Simple Audio
Card, Audio Graph Card, Audio Graph Card2), and Renesas/Kuninori
Morimoto wants to test these.
The Generic Audio Card driver had been requested on ALSA SoC.
It supports many types of device connection methods, and historically,
the requested connection support range of the generic driver has been
upgraded.
Upgrading the connection support range itself could not be implemented
in the generic driver, because we need to keep compatibility with old
DTBs. This is one of the reasons why we have many types of Generic Audio
Card driver.
The ULCB/KF combo is a good board stack to test these.
Kuninori has been testing these Generic Audio Card drivers by using his
local patches to switching drivers. But from an information sharing
point of view, it is a good idea to upstream these, because the DT
configuration is complex. Hence this can be a good sample for the user.
Hence add an "Audio Graph Card" DT setting file for ULCB/KF.
This can be enabled by updating ulcb.dtsi / ulcb-kf.dtsi.
From a normal user point of view who doesn't need to test the driver,
everything should stay as-is, and nothing changes.
Note that because this needs "switching driver", and not "adding extra
feature", this does not use a Device Tree overlay.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87bkn3i414.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Current sound comment is indicating that #sound-dai-cells is required,
but it is needed only if board is using "simple-card".
Hence tidy up the comments.
As ulcb.dtsi and salvator-common.dtsi are already using "audio-graph",
the unneeded #sound-dai-cells are removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87cz7ji418.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Current sound comment is indicating that #sound-dai-cells is required,
but it is needed only if the board is using "simple-card".
Hence tidy up the comments.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87edrzi41e.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Describe the external SCIF clock crystal, which can be used as a clock
source for the (High Speed) Serial Communication Interfaces with FIFO.
This improves serial console accuracy from 115200-257 bps to
115200+0 bps.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7dddaa362945118deab534ccfddfc0870abe8526.1673271243.git.geert+renesas@glider.be
|
|
Add the USBF controller available in the r9a06g032 SoC.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230105152257.310642-5-herve.codina@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The PHY interrupt (INT_N) pin is connected to IRQ2 and IRQ7 for ETH0 and
ETH1 respectively.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230102221815.273719-7-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add required properties in pinctrl node to handle GPIO interrupts.
Note as IRQC is not enabled in RZ/Five the phandle for interrupt-parent
is added in RZ/G2UL specific dtsi so that RZ/Five pinctrl driver
continues without waiting for IRQC to probe.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230102221815.273719-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add IRQC node to R9A07G043 (RZ/G2UL) SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230102221815.273719-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
IRQC support for RZ/Five is still missing so drop the interrupts and
interrupt-parent properties from the PHY nodes of ETH{0,1}.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230102222708.274369-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add an operating point for running the Cortex-A76 CPU cores on R-Car
V4H at 1.8 GHz (High Performance mode).
Based on a patch in the BSP by Tho Vu.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/cc2bae27776523f499d01655ef18fe463a3ae1ae.1670492384.git.geert+renesas@glider.be
|
|
Ensure appropriate configuration is done to make the host1x device
and context devices DMA coherent by adding the dma-coherent flag.
Fixes: b35f5b53a87b ("arm64: tegra: Add context isolation domains on Tegra234")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Update the address-cells and size-cells to 2 in order to support 64-bit
addressing.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Use generic "mcu" node name for rave-sp node, as recommended by
Devicetree specification.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
imx6ulz is derived SoC from imx6ull.
Currently, the boards based on imx6ulz are correctly recognized only if
the compatible includes "fsl,imx6ull", while "fsl,imx6ulz" is ignored.
Signed-off-by: Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use try_cmpxchg instead of cmpxchg (*ptr, old, new) == old in
__acpi_{acquire,release}_global_lock(). x86 CMPXCHG instruction returns
success in ZF flag, so this change saves a compare after CMPXCHG
(and related MOV instruction in front of CMPXCHG).
Also, try_cmpxchg() implicitly assigns old *ptr value to "old" when CMPXCHG
fails. There is no need to re-read the value in the loop.
Note that the value from *ptr should be read using READ_ONCE() to prevent
the compiler from merging, refetching or reordering the read.
No functional change intended.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20230116162522.4072-1-ubizjak@gmail.com
|
|
Use try_cmpxchg instead of cmpxchg (*ptr, old, new) == old in
set_page_memtype. x86 CMPXCHG instruction returns success in ZF flag,
so this change saves a compare after cmpxchg (and related move
instruction in front of cmpxchg).
Also, try_cmpxchg implicitly assigns old *ptr value to "old" when cmpxchg
fails. There is no need to re-read the value in the loop.
Note that the value from *ptr should be read using READ_ONCE to prevent
the compiler from merging, refetching or reordering the read.
No functional change intended.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230116163446.4734-1-ubizjak@gmail.com
|
|
DT schema expects names of operating points tables to match certain
pattern:
stih418-b2264.dtb: opp_table: $nodename:0: 'opp_table' does not match '^opp-table(-[a-z0-9]+)?$'
Link: https://lore.kernel.org/r/20230120072110.138627-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Bindings expect UART/serial node names to be "serial".
Link: https://lore.kernel.org/r/20230123151536.369623-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Bindings expect UART/serial node names to be "serial".
Link: https://lore.kernel.org/r/20230123151525.369255-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Bindings expect UART/serial node names to be "serial".
Link: https://lore.kernel.org/r/20230123151529.369313-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Bindings expect UART/serial node names to be "serial".
Link: https://lore.kernel.org/r/20230123151545.369762-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
The device_type property is deprecated by Devicetree specification and
bindings do not allow it.
Link: https://lore.kernel.org/r/20230123151547.369791-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
The device_type property is deprecated by Devicetree specification and
bindings do not allow it.
Link: https://lore.kernel.org/r/20230123151549.369818-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Bindings expect UART/serial node names to be "serial".
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20230123151533.369533-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
By convention the hex addresses should be lowercase.
Link: https://lore.kernel.org/r/20230125094513.155063-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Align HDMI and USB phy node names with bindings expectation.
Link: https://lore.kernel.org/r/20230125094513.155063-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
The HDMI phy compatible was missing vendor prefix.
Fixes: ed80d4cab772 ("ARM: dts: add hdmi related nodes for exynos4 SoCs")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230125094513.155063-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
clang correctly complains
arch/x86/kernel/cpu/resctrl/rdtgroup.c:1456:6: warning: variable \
'h' set but not used [-Wunused-but-set-variable]
u32 h;
^
but it can't know whether this use is innocuous or really a problem.
There's a reason why those warning switches are behind a W=1 and not
enabled by default - yes, one needs to do:
make W=1 CC=clang HOSTCC=clang arch/x86/kernel/cpu/resctrl/
with clang 14 in order to trigger it.
I would normally not take a silly fix like that but this one is simple
and doesn't make the code uglier so...
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/202301242015.kbzkVteJ-lkp@intel.com
|
|
When a module with a livepatched function is unloaded and then reloaded,
klp attempts to dynamically re-patch it. On ppc64, that fails with the
following error:
module_64: livepatch_nfsd: Expected nop after call, got e8410018 at e_show+0x60/0x548 [livepatch_nfsd]
livepatch: failed to initialize patch 'livepatch_nfsd' for module 'nfsd' (-8)
livepatch: patch 'livepatch_nfsd' failed for module 'nfsd', refusing to load module 'nfsd'
The error happens because the restore r2 instruction had already
previously been written into the klp module's replacement function when
the original function was patched the first time. So the instruction
wasn't a nop as expected.
When the restore r2 instruction has already been patched in, detect that
and skip the warning and the instruction write.
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Song Liu <song@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/2f6329ffd9674df6ff57e03edeb2ca54414770ab.1674617130.git.jpoimboe@kernel.org
|
|
restore_r2() returns 1 on success, which is surprising for a non-boolean
function. Change it to return 0 on success and -errno on error to match
kernel coding convention.
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Song Liu <song@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/15baf76c271a0ae09f7b8556e50f2b4251e7049d.1674617130.git.jpoimboe@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
Some Ux500 DTS updates for the v6.3 kernel:
- Fix up LED node names
- Add a clkout-node for the external clock
* tag 'ux500-dts-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ux500: Add clkout-clock node
ARM: dts: ste: align LED node names with dtschema
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Follow the change that has been done on imx8mm-verdin-dev.dtsi and
remove the include from dahlia to be consistent. Put back all nodes that
previously had been included.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Inheriting the dahlia devicetree leads to inheriting certain settings
for the audio-codec that are not correct and hence the dt schema check
failing.
Remove that include and put all nodes back that had been included.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The VSELECT pin is configured as MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT
and not as a GPIO, drop the bogus sd-vsel-gpios property as the eSDHC
block handles the VSELECT pin on its own.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The VSELECT pin is configured as MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT
and not as a GPIO, drop the bogus sd-vsel-gpios property as the eSDHC
block handles the VSELECT pin on its own.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The VSELECT pin is configured as MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT
and not as a GPIO, drop the bogus sd-vsel-gpios property as the eSDHC
block handles the VSELECT pin on its own.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use PLL1_80M instead of PLL3 to drive UART2 clock divided down to 80 MHz
instead of 64 MHz to obtain suitable block clock for exact 4 Mbdps, which
is the maximum supported baud rate by the muRata 2AE BT UART.
The difference here is that at 64 MHz UART block clock, the clock with are
divided by 16 (due to oversampling) to 4 MHz and the baud rate generator
then needs to be set to UBIR+1/UBMR+1 = 1/1 to yield 4 Mbdps . In case of
80 MHz UART block clock divided by 16 to 5 MHz, the baud rate generator
needs to be set to UBIR+1/UBMR+1 = 4/5 to yield 4 Mbdps .
Both options are valid and yield the same result, except using the PLL1_80M
output requires fewer clock tree changes, since the PLL1 already generates
the 80 MHz usable for UART, which frees the PLL3 for other uses.
Suggested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Beacon Embedded has an i.MX8M Plus development kit which consists
of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC,
and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual
Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet
PHY.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Commit c871335217e7 ("arm64: dts: imx8mm-evk: Enable pca6416 on i2c3
bus") says that the assembled expander is a PCA6416 and not a TCA6416.
No functional change since the driver handles both expanders the same
way.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add ADC support for imx93-11x11-evk board.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Reorder the PCIe clock in DT to match YAML DT schema. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
