| Age | Commit message (Collapse) | Author |
|---|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Some USB peripherals draw more power, and the sourcing regulator
take a little time to turn on. This patch fixes an issue where
some devices occasionally do not get detected, because the power
isn't quite ready when communication starts, so we add a bit
of a delay.
Fixes: 1c207f911fe9 ("ARM: dts: imx: Add support for Logic PD i.MX6QD EVM")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The main 3.3V regulator sources a series of additional regulators.
This patch adds a small delay, so when the 3.3V regulator comes
on it delays a bit before the subsequent regulators can come on.
This reduces the inrush current a bit on the external DC power
supply to help prevent a situation where the sourcing power supply
cannot source enough current and overloads and the kit fails to
start.
Fixes: 1c207f911fe9 ("ARM: dts: imx: Add support for Logic PD i.MX6QD EVM")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The LCD power sequencer is very finicky. The backlight cannot
be driven until after the sequencer is done. Until now, the
regulators were marked with 'regulator-always-on' to make sure
it came up before the backlight. This patch allows the LCD
regulators to power down and prevent the backlight from being
used again until the sequencer is ready. This reduces
standby power consumption by ~100mW.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The original submission had functional audio out and was based
on reviewing other boards using the same wm8962 codec. However,
the Logic PD board uses an analog microphone which was being
disabled for a digital mic. This patch corrects that and
explicitly sets the gpio-cfg pins all to 0x0000 which allows the
analog microphone to capture audio.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The support for XIVE native exploitation mode in Linux/KVM needs a
couple more OPAL calls to get and set the state of the XIVE internal
structures being used by a sPAPR guest.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add #cooling-cells for i.MX6SLL cpu-freq cooling device usage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Kobo Aura is an e-book reader released in 2013.
With the devicetree in its current state, the kernel will boot and run
for about ten seconds. To solve this, the embedded controller needs to
be told that the system should stay powered on. This will be done in a
later patchset.
- The IOMUXC mode bits for the SD interfaces were taken from the
vendor's U-Boot fork.
- The bus width of the eMMC is 4 bits in the vendor kernel, but I
achieved better performance with 8 bits.
- The SDIO clock frequency for the WiFi chip is 25MHz in the vendor
kernel, but the WiFi chip (BCM43362) supports 50MHz, which works
reliably on this board and gives slightly better performance.
- The I2C pins' IOMUXC settings come from the vendor's U-Boot fork.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Commit 6d4cd041f0af ("net: phy: at803x: disable delay only for RGMII mode")
exposed an issue on imx DTS files using AR8031/AR8035 PHYs.
The end result is that the boards can no longer obtain an IP address
via UDHCP, for example.
Quoting Andrew Lunn:
"The problem here is, all the DTs were broken since day 0. However,
because the PHY driver was also broken, nobody noticed and it
worked. Now that the PHY driver has been fixed, all the bugs in the
DTs now become an issue"
To fix this problem, the phy-mode property needs to be "rgmii-id", which
has the following meaning as per
Documentation/devicetree/bindings/net/ethernet.txt:
"RGMII with internal RX and TX delays provided by the PHY, the MAC should
not add the RX or TX delays in this case)"
Tested on imx6-sabresd, imx6sx-sdb and imx7d-pico boards with
successfully restored networking.
Based on the initial submission from Steve Twiss for the
imx6qdl-sabresd.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Soeren Moch <smoch@web.de>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Adam Thomson <Adam.Thomson@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", the driver now accepts this name, use it here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", the driver now accepts this name, use it here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", the driver now accepts this name, use it here.
Note the GPIO polarity in the driver was ignored before and always
assumed to be active low, when all the DTs are fixed we will start
respecting the specified polarity. Switch polarity in DT to the
currently assumed one, this way when the driver changes the
behavior will not change.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SL_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SLL_CLK_SDMA result in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SLL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6UL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6UL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX7D_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX7D_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SX_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SX_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6QDL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality(this at least
breaks RAVE SP serdev driver on RDU2). Fix the code to specify
IMX6QDL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting incorrect
clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Warp7 comes with a Omnivision OV2680 sensor, add the node here to make
complete the camera data path for this system. Add the needed regulator
to the analog voltage supply, the port and endpoints in mipi_csi node
and the pinctrl for the reset gpio.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add and enable csi and mipi_csi nodes.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add device tree nodes for csi, video multiplexer and mipi-csi.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The IOMUXC General Purpose Register has bitfield to control video bus
multiplexer to control the CSI input between the MIPI-CSI2 and parallel
interface. Add that register and mask.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add power domain index 0 related with mipi-phy to imx7s.
While at it rename pcie power-domain node to remove pgc prefix.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add SATA device nodes for fsl-lx2160a and enable support
for QDS and RDB boards.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Ls1028a SATA ecc address with more than 32 bit, so we should corrrect the
address.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds support for the TQ TQMa7D SoM together with
the MBa7 carrier board and it's based on the NXP i.MX7Dual SoC.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds support for the TQ TQMa7S SoM together with
the MBa7 carrier board and it's based on the NXP i.MX7Solo SoC.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds TQMa7 and MBa7 board support.
TQMa7 can be mounted with either i.MX7 Solo or Dual.
All TQMa7 board variants can be mounted in MBa7 carrier board.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is the ancient loading interface which requires special tools to be
used. The bigger problem with it is that it is as inadequate for proper
loading of microcode as the late microcode loading interface is because
it happens just as late.
iucode_tool's manpage already warns people that it is deprecated.
Deprecate it and turn it off by default along with a big fat warning in
the Kconfig help. It will go away sometime in the future.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: x86@kernel.org
Link: https://lkml.kernel.org/r/20190405133010.24249-4-bp@alien8.de
|
|
Commit
2613f36ed965 ("x86/microcode: Attempt late loading only when new microcode is present")
added the new define UCODE_NEW to denote that an update should happen
only when newer microcode (than installed on the system) has been found.
But it missed adjusting that for the old /dev/cpu/microcode loading
interface. Fix it.
Fixes: 2613f36ed965 ("x86/microcode: Attempt late loading only when new microcode is present")
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jann Horn <jannh@google.com>
Link: https://lkml.kernel.org/r/20190405133010.24249-3-bp@alien8.de
|
|
As reported by 0-DAY kernel test infrastructure:
arch/x86//kernel/ima_arch.c: In function 'arch_get_ima_policy':
>> arch/x86//kernel/ima_arch.c:78:4: error: implicit declaration of
function 'set_module_sig_enforced' [-Werror=implicit-function-declaration]
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
|
|
Change generic_load_microcode() to use the iov_iter API instead of a
clumsy open-coded version which has to pay attention to __user data
or kernel data, depending on the loading method. This allows to avoid
explicit casting between user and kernel pointers.
Because the iov_iter API makes it hard to read the same location twice,
as a side effect, also fix a double-read of the microcode header (which
could e.g. lead to out-of-bounds reads in microcode_sanity_check()).
Not that it matters much, only root is allowed to load microcode
anyway...
[ bp: Massage a bit, sort function-local variables. ]
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190404111128.131157-1-jannh@google.com
|
|
Now that we allow drivers to always need to set larger than required
DMA masks we need to be a little more careful in the sun4v PCI iommu
driver to chose when to select the ATU support - a larger DMA mask
can be set even when the platform does not support ATU, so we always
have to check if it is avaiable before using it. Add a little helper
for that and use it in all the places where we make ATU usage decisions
based on the DMA mask.
Fixes: 24132a419c68 ("sparc64/pci_sun4v: allow large DMA masks")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Meelis Roos <mroos@linux.ee>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
Use the new Stratix10 binding format for EDAC nodes.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: mark.rutland@arm.com
Cc: mchehab@kernel.org
Link: https://lkml.kernel.org/r/1554388597-28019-4-git-send-email-thor.thayer@linux.intel.com
|
|
The Maximum Physical Memory 2GiB option for 64bit systems is currently
broken because kernel hangs at boot-time when this option is enabled
and the underlying system has more than 2GiB memory.
This issue can be easily reproduced on SiFive Unleashed board where
we have 8GiB of memory.
This patch fixes above issue by removing unusable memory region in
setup_bootmem().
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
Currently, compat tasks running on arm64 can allocate memory up to
TASK_SIZE_32 (UL(0x100000000)).
This means that mmap() allocations, if we treat them as returning an
array, are not compliant with the sections 6.5.8 of the C standard
(C99) which states that: "If the expression P points to an element of
an array object and the expression Q points to the last element of the
same array object, the pointer expression Q+1 compares greater than P".
Redefine TASK_SIZE_32 to address the issue.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jann Horn <jannh@google.com>
Cc: <stable@vger.kernel.org>
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
[will: fixed typo in comment]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
After changing the argument of __raw_xsave_addr() from a mask to
number Dave suggested to check if it makes sense to do the same for
get_xsave_addr(). As it turns out it does.
Only get_xsave_addr() needs the mask to check if the requested feature
is part of what is supported/saved and then uses the number again. The
shift operation is cheaper compared to fls64() (find last bit set).
Also, the feature number uses less opcode space compared to the mask. :)
Make the get_xsave_addr() argument a xfeature number instead of a mask
and fix up its callers.
Furthermore, use xfeature_nr and xfeature_mask consistently.
This results in the following changes to the kvm code:
feature -> xfeature_mask
index -> xfeature_nr
Suggested-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Rik van Riel <riel@surriel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Siarhei Liakh <Siarhei.Liakh@concurrent-rt.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190403164156.19645-12-bigeasy@linutronix.de
|
|
Remove the "console=ttySAC..." argument from DTSes having a proper
stdout-path property. To make the code functionally equivalent, add the
serial port baud rate and parity.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Replacing bootargs with stdout-path property in chosen node allows using
early console by adding just 'earlycon' parameter to the kernel command
line.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
|
|
Support for Exynos5420/5422/5800 SoCs requires MCPM to properly boot all
CPU cores on all currectly supported platforms: Peach Pit (Exynos5420),
Odroid XU3/XU3lite/XU4/HC1 (Exynos5422) and Peach Pi (Exynos5800).
Without it some CPU cores fail to come online. Remove then the ability to
disable MCPM and make it mandatory when Exynos542x/5800 support is
enabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
If CONFIG_PGSTE is not set (e.g. when compiling without KVM), GCC complains:
CC arch/s390/mm/pgtable.o
arch/s390/mm/pgtable.c:413:15: warning: ‘pmd_alloc_map’ defined but not
used [-Wunused-function]
static pmd_t *pmd_alloc_map(struct mm_struct *mm, unsigned long addr)
^~~~~~~~~~~~~
Wrap the function with "#ifdef CONFIG_PGSTE" to silence the warning.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Disallow kernel command line alteration via ipl parameter block if
running in protected virtualization environment.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Add sharing of ipl parameter block for diag 308 set/store calls to allow
kvm access in protected virtualization environment.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The Ultravisor Call Facility (stfle bit 158) defines an API to the
Ultravisor (UV calls), a mini hypervisor located at machine
level. With help of the Ultravisor, KVM will be able to run
"protected" VMs, special VMs whose memory and management data are
unavailable to KVM.
The protected VMs can also request services from the Ultravisor.
The guest api consists of UV calls to share and unshare memory with the
kvm hypervisor.
To enable this feature support PROTECTED_VIRTUALIZATION_GUEST kconfig
option has been introduced.
Co-developed-by: Janosch Frank <frankja@de.ibm.com>
Signed-off-by: Janosch Frank <frankja@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Same as for .boot.data section make sure that .boot.preserved.data
sections of vmlinux and arch/s390/compressed/vmlinux match before
producing the compressed kernel image. Symbols presence, order and sizes
are cross-checked.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
.boot.preserved.data is a better fit for ipl block than .boot.data
which is discarded after init. Reusing .boot.preserved.data allows to
simplify code a little bit and avoid copying data from .boot.data to
persistent variables.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
