| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Avoid un-intended DCTI Couples. Use of DCTI couples is deprecated.
Also address the "Programming Note" for optimal performance.
Here is the complete text from Oracle SPARC Architecture Specs.
6.3.4.7 DCTI Couples
"A delayed control transfer instruction (DCTI) in the delay slot of
another DCTI is referred to as a “DCTI couple”. The use of DCTI couples
is deprecated in the Oracle SPARC Architecture; no new software should
place a DCTI in the delay slot of another DCTI, because on future Oracle
SPARC Architecture implementations DCTI couples may execute either
slowly or differently than the programmer assumes it will.
SPARC V8 and SPARC V9 Compatibility Note
The SPARC V8 architecture left behavior undefined for a DCTI couple. The
SPARC V9 architecture defined behavior in that case, but as of
UltraSPARC Architecture 2005, use of DCTI couples was deprecated.
Software should not expect high performance from DCTI couples, and
performance of DCTI couples should be expected to decline further in
future processors.
Programming Note
As noted in TABLE 6-5 on page 115, an annulled branch-always
(branch-always with a = 1) instruction is not architecturally a DCTI.
However, since not all implementations make that distinction, for
optimal performance, a DCTI should not be placed in the instruction word
immediately following an annulled branch-always instruction (BA,A or
BPA,A)."
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Reviewed-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I encountered this bug when using /proc/kcore to examine the kernel. Plus a
coworker inquired about debugging tools. We computed pa but did
not use it during the maximum physical address bits test. Instead we used
the identity mapped virtual address which will always fail this test.
I believe the defect came in here:
[bpicco@zareason linus.git]$ git describe --contains bb4e6e85daa52
v3.18-rc1~87^2~4
.
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nitin Gupta <nitin.m.gupta@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nitin Gupta <nitin.m.gupta@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the current task, the kernel stack would only tell the last time the
process was rescheduled, if ever. Use the current stack pointer for the
current task.
Otherwise, every once in a while, the stacktrace printed when reading
/proc/self/stack would look like the process is running in userspace,
while it's not, which some may consider as a bug.
This is also consistent with some other architectures, like x86 and arm,
at least.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
... and make the users of generic uaccess.h use that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
cpu_ready_for_interrupts() is called after feature patching, so there's
no need to use early_cpu_has_feature().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The config option for the POWER8 crc32c recently changed from
CONFIG_CRYPT_CRC32C_VPMSUM to CONFIG_CRYPTO_CRC32C_VPMSUM. Update
the configs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Most people use perf these days, so save about 31kB by making oprofile
a module.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
It turns out cloud-config uses ISO9660 filesystems to inject
configuration data into cloud images. The cloud-config failures when
ISO9660_FS is not enabled are cryptic, and building it in makes
mainline testing easier, so re-enable it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
POWER9 adds form 1 scoms. The form of the indirection is specified in
the top nibble of the scom address.
Currently we do some (ugly) bit mangling so that we can fit a 64 bit
scom address into the debugfs interface. The current code only shifts
the top bit (indirect bit).
This patch changes it to shift the whole top nibble so that the form
of the indirection is also shifted.
This patch is backwards compatible with older scoms.
(This change isn't required in the arch/powerpc/platforms/powernv/opal-prd.c
scom interface as it passes the whole 64bit scom address without any bit
mangling)
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently the code to perform an OPAL call is duplicated between the
normal path and path taken when tracepoints are enabled. There's no
real need for this and combining them makes opal_tracepoint_entry
considerably easier to understand.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently the xmon debugger is set only via kernel boot command-line.
It's disabled by default, and can be enabled with "xmon=on" on the
command-line. Also, xmon may be accessed via sysrq mechanism.
But we cannot enable/disable xmon in runtime, it needs kernel reload.
This patch introduces a debugfs entry for xmon, allowing user to query
its current state and change it if desired. Basically, the "xmon" file
to read from/write to is under the debugfs mount point, on powerpc
directory. It's a simple attribute, value 0 meaning xmon is disabled
and value 1 the opposite. Writing these states to the file will take
immediate effect in the debugger.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The xmon parameter nobt was added long time ago, by commit 26c8af5f01df
("[POWERPC] print backtrace when entering xmon"). The problem that time
was that during a crash in a machine with USB keyboard, xmon wouldn't
respond to commands from the keyboard, so printing the backtrace wouldn't
be possible.
Idea then was to show automatically the backtrace on xmon crash for the
first time it's invoked (if it recovers, next time xmon won't show
backtrace automatically). The nobt parameter was added _only_ to prevent
this automatic trace show. Seems long time ago USB keyboards didn't work
that well!
We don't need this parameter anymore, the feature of auto showing the
backtrace is interesting (imagine a case of auto-reboot script),
so this patch extends the functionality, by always showing the backtrace
automatically when xmon is invoked; it removes the nobt parameter too.
Also, this patch fixes __initdata placement on xmon_early and replaces
__initcall() with modern device_initcall() on sysrq handler.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Once xmon is triggered by sysrq-x, it is enabled always afterwards even
if it is disabled during boot. This will cause a system reset interrupt
fail to dump. So keep xmon in its original state after exit.
We have several ways to set xmon on or off.
1) by a build config CONFIG_XMON_DEFAULT.
2) by a boot cmdline with xmon or xmon=early or xmon=on to enable xmon
and xmon=off to disable xmon. This value will override that in step 1.
3) by a debugfs interface, as proposed in this patchset.
And this value can override those in step 1 and 2.
Signed-off-by: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- build warning fix
- defconfig updates
- wire up new statx syscall
* tag 'm68k-for-v4.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up statx
m68k/defconfig: Update defconfigs for v4.11-rc1
m68k/bitops: Correct signature of test_bit()
|
|
Commit 3251885285e1 ("ARM: OMAP4+: Reset CPU1 properly for kexec") started
unconditionally resetting CPU1 because of a kexec boot issue I was seeing
earlier on omap4 when doing kexec boot between two different kernel
versions.
This caused issues on some systems. We should only reset CPU1 as a last
resort option, and try to avoid it where possible. Doing an unconditional
CPU1 reset causes issues for example when booting a bootloader configured
secure OS running on CPU1 as reported by Andrew F. Davis <afd@ti.com>.
We can't completely remove the reset of CPU1 as it would break kexec
booting from older kernels. But we can limit the CPU1 reset to cases
where CPU1 is wrongly parked within the memory area used by the booting
kernel. Then later on we can add support for parking CPU1 for kexec out
of the SDRAM back to bootrom.
So let's first fix the regression reported by Andrew by making CPU1 reset
conditional. To do this, we need to:
1. Save configured AUX_CORE_BOOT_1 for later
2. Modify AUX_CORE_BOOT_0 reading code to for HS SoCs to return
the whole register instead of the CPU mask
3. Check if CPU1 is wrongly parked into the booting kernel by the
previous kernel and reset if needed
Fixes: 3251885285e1 ("ARM: OMAP4+: Reset CPU1 properly for kexec")
Reported-by: Andrew F. Davis <afd@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Tested-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
An alias name should have an index number even when it is the only of its type.
This allows U-Boot to add the local-mac-address property. Otherwise U-Boot
skips the alias.
Fixes: 6a93792774 ("ARM: bcm2835: dt: Add the ethernet to the device trees")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
According to the BCM2835 ARM Peripherals document uart1 doesn't map to pins
36-39, but uart0 does.
Also, split into separate Rx/Tx and CST/RTS groups to match other uart nodes.
Fixes: 21ff843931b ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
According to the BCM2835 ARM Peripherals document i2c0 doesn't map to pins 32,
34 but to 28, 29.
Fixes: 21ff843931b ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
Downstream kernel uses pins 32, 33 as UART0 (PL011) Rx/Tx to communicate with
the Bluetooth chip. So ALT3 of these pins is most likely not CTS/RTS. Change
the node name to reflect that. This matches section 6.2 "Alternative Function
Assignments" in the BCM2835 ARM Peripherals document.
With this change in place, adding
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
status = "okay";
};
to bcm2837-rpi-3-b.dts does the right thing on my Raspberry Pi 3.
Pins 30, 31 are CTS/RTS of UART0 in alternate function 3. Rename uart0_gpio30
as well.
While at it, fix a little typo in a nearby comment.
Fixes: 21ff843931b ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
mmc2 used for wl12xx was missing the keep-power-in suspend
parameter. As a result the board couldn't reach suspend state.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Orange Pi Zero board features a USB OTG port, which has a ID pin, and
can be used to power up the board. However, even if the board is powered
via +5V pin in GPIO/expansion headers, the VBUS in the OTG port cannot
be powered up, thus it's impossible to use it in host mode with simple
OTG cables.
Add support for it in peripheral mode.
If someone really want to use it in host mode, the mode of PHY can be
switch via sysfs, then use a powered USB OTG cable or powered USB HUB to
power up external USB devices.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Orange Pi One features a MicroUSB port that can work in both host mode
and peripheral mode.
When in host mode, its VBUS is controlled via a GPIO; when in peripheral
mode, its VBUS cannot be used to power up the board.
Add support for this port.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Orange Pi PC 2 board features a OTG port like the one on older H3 Orange
Pi's, with PG12 pin being the id det pin and PL2 being the vbus driver
pin.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Reviewed-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
change MMC cd to active-low, rename some node names to prevent
underscores]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
refactor, commit message changed to meet new arm64 naming scheme,
drop H3 pinctrl compatible because of interrupt bank change, drop
H3 ccu compatible because of clock change, drop ccu node as it come
into h3-h5 dtsi]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Allwinner H3/H5 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
or MUSB controller.
Add device nodes for these controllers.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc and gic, as well as pio and ccu's
compatible, and make drop of skeleton into a seperated patch]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
According to the datasheets provided by Allwinner, both Allwinner H3 and
H5 use GIC-400 as their interrupt controller.
For better device tree reusing, correct the GIC compatible in H3 DTSI to
"arm,gic-400", thus this node can be reused in H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
After converting to generic pinconf binding, pinctrl-a10.h is now not
used at all.
Drop its inclusion for H3 DTSI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The skeleton.dtsi file is now deprecated, and do not exist in ARM64
environment.
Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
chip, drop skeleton.dtsi inclusion now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This commit makes use of the axp209.dtsi file to define the
AXP209 PMIC. While here, define the rails that are enabled on
this board.
Tested checking the regulator voltage varies according to the
CPU frequency.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The SinA31s has a coaxial SPDIF output. Enable it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This adds the cpu-supply DT property to the cpu0 DT node needed by
the board to adapt the regulator voltage depending on the currently used
OPP.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This adds almost all operating points allowed for the A33 as defined by
fex files available at:
https://github.com/linux-sunxi/sunxi-boards/tree/master/sys_config/a33
There are more possible frequencies in this patch than there are in the
fex files because the fex files only give an interval of possible
frequencies for a given voltage. All supported frequencies are defined
in the original driver code in Allwinner vendor tree.
There are two missing frequencies though: 1104MHz and 1200MHz which
require the CPU to have 1.32V supplied, which is higher than the default
voltage.
Without all A33 boards defining the CPU regulator, we cannot have these
two frequencies as it would cause the CPU to try to run a higher
frequency without "overvolting" which is very likely to crash the CPU.
Therefore, these two frequencies must be enabled on a per-board basis.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The NextThing Co. CHIP has an AXP209 PMIC and can be power-supplied by
ACIN via the CHG-IN pin.
This enables the ACIN power supply subnode in the DT.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Sinlinx SinA33 has an AXP223 PMIC and an ACIN connector, thus, we
enable the ACIN power supply in its Device Tree.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The X-Powers AXP22X PMIC exposes the status of AC power supply.
This adds the AC power supply subnode for the AXP22X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The X-Powers AXP20X PMIC exposes the status of AC power supply, the
current current and voltage supplied to the board by the AC power
supply.
This adds the AC power supply subnode for AXP20X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The old sunxi specific pinctrl bindings are deprecated, in favor of
the new generic pinconf bindings. Also, we are moving towards handling
GPIO pinmux settings that don't require extra bias or drive strength
settings to use the GPIO bindings only.
This patch removes the last instance of the sunxi specific pinctrl
bindings that use the pinctrl header by dropping the pinmux setting
for the audio codec's PA (external amplifier) control GPIO. The pin
is pulled down externally.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
By using "UD0" for WARN()s we remove the function call and its possible
__FILE__ and __LINE__ immediate arguments from the instruction stream.
Total image size will not change much, what we win in the instruction
stream we'll lose because of the __bug_table entries. Still, saves on
I$ footprint and the total image size does go down a bit.
text data filename
10702123 4530992 defconfig-build/vmlinux.orig
10682460 4530992 defconfig-build/vmlinux.patched
(UML didn't seem to use GENERIC_BUG at all, so remove it)
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Weinberger <richard.weinberger@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This resolves a merge issue in the gadget code, and we want the USB
fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the char-misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch converts x86 to use proper folding of a new (fifth) page table level
with <asm-generic/pgtable-nop4d.h>.
That's a bit of a kitchen sink patch, but I don't see how to split it further
without hurting bisectability.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-arch@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170317185515.8636-7-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Split these helpers into a couple of per-level functions and add support for
an additional page table level.
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
[ Split off into separate patch ]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-arch@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170317185515.8636-6-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
With folded p4d, pgd_clear() is a nop. Change clear_pgds() to use
p4d_clear() instead.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-arch@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170317185515.8636-5-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Straight-forward extension of existing code to support additional page
table level.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-arch@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170317185515.8636-4-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
