| Age | Commit message (Collapse) | Author |
|---|
|
dw-mmc got its reset-properties specified, so add the softresets
for it on the rk3368.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
|
|
Default to disable mailbox in rk3368 core dts file.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
I2S of RK3368 SoCs keep same as RK3066 SoCs found on Rockchip,
add nodes to support them.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add dmac bus and dmac peri dts nodes for peripherals,
such as I2S, SPI, UART and so on.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
As reported by Lorenzo, the residency/latency values defined in the
idle-state for rk3368 "make no sense". When introducing them I
simply took the idle-state node from the vendor kernel in error
as I didn't look up if these values were sane in the first place.
Talking to people and determining why they were used in this way
showed that it was meant to make sure the cpu_suspend callback
got initialized which at the 3.10 time was somehow required even
for wfi-based idle handling.
Of course the generic arch_cpu_idle() now does wfi-based idle-handling
already and the rk3368 does not implement any other idle states than
the default WFI, so these wrong idle-states should go away.
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Used for Gru/Kevin only, as they're the only ones which have a described
CPU regulator. Also, I'm not sure we've validated this table non-Gru
boards.
At the same time, partially describe PWM regulators for Gru, so cpufreq
doesn't think it can crank up the clock speed without changing the
voltage. However, we don't yet have the DT bindings to fully describe
the Over Voltage Protection (OVP) circuits on these boards. Without that
description, we might end up changing the voltage too much, too fast.
Add the pwm-regulator descriptions and associate the CPU OPPs, but leave
them disabled.
Signed-off-by: Brian Norris <briannorris@chromium.org>
[shared gru/kevin parts on a gru device]
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[with a bit of reordering]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Kevin is part of a family of boards called Gru. As best as possible, the
properties shared by the Gru family are placed in rk3399-gru.dtsi, while
Kevin-specific bits are in rk3399-gru-kevin.dts. This does not add full
support for the base Gru board.
Working and tested (to some extent):
* EC support -- including keyboard, battery, PWM, and probably more
* UART / console
* Thermal
* Touchscreen
* Touchpad
* Digitizer (regulator still WIP)
* PCIe / Wifi
* Bluetooth / Webcam
* SD card
* eMMC
* USB2 on TypeC
- This works much of the time, but USB3 devices may or may not detect
properly. Waiting on proper extcon support for USB3 over TypeC.
- Depends on XHCI/DWC3 fixes for ARM64 that still haven't landed
* Backlight
Not working:
* CPUFreq -- relies on special OVP support for our PWM regulator
circuits
* EC / extcon support -- and with it, USB3/TypeC/DP
* DRM -- won't even build on ARM64, so all display, eDP, etc. is not
enabled
Not tested:
* Audio
Signed-off-by: Brian Norris <briannorris@chromium.org>
[shared gru/kevin parts on a gru device]
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[with a bit of reordering]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
When the separate IRQ stack was introduced, stack unwinding only
proceeded as far as the top of the IRQ stack, leading to kernel
backtraces being less useful, lacking the trace of what was interrupted.
Fix this by providing a means for the kernel to unwind the IRQ stack
onto the interrupted task stack. The processor state is saved to the
kernel task stack on interrupt. The IRQ_STACK_START macro reserves an
unsigned long at the top of the IRQ stack where the interrupted task
stack pointer can be saved. After the active stack is switched to the
IRQ stack, save the interrupted tasks stack pointer to the reserved
location.
Fix the stack unwinding code to look for the frame being the top of the
IRQ stack and if so get the next frame from the saved location. The
existing test does not work with the separate stack since the ra is no
longer pointed at ret_from_{irq,exception}.
The test to stop unwinding the stack 32 bytes from the top of a stack
must be modified to allow unwinding to continue up to the location of
the saved task stack pointer when on the IRQ stack. The low / high marks
of the stack are set depending on whether the sp is on an irq stack or
not.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jason A. Donenfeld <jason@zx2c4.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15788/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add the dwc3 usb needed node information for rk3399.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
According to [0] pointed out by Marc Zyngier in a report about a
similar error message, PPIs 11 and 13 are edge triggered on
Cortex-A9 socs including the rk3066 and rk3188 which currently
mark them as level triggered.
Until some time ago the gic did not care but commit 992345a58e0c
("irqchip/gic: WARN if setting the interrupt type for a PPI fails")
introduced a warning for that case.
Fix the warning on these socs by describing the interrupts correctly
and also using the binding constants for easier reading in the future.
[0] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0407f/CCHEIGIC.html
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Back in commit:
92b0729c34cab ("x86/mm, x86/mce: Add memcpy_mcsafe()")
... I made a copy/paste error setting up the exception table entries
and ended up with two for label .L_cache_w3 and none for .L_cache_w2.
This means that if we take a machine check on:
.L_cache_w2: movq 2*8(%rsi), %r10
then we don't have an exception table entry for this instruction
and we can't recover.
Fix: s/3/2/
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 92b0729c34cab ("x86/mm, x86/mce: Add memcpy_mcsafe()")
Link: http://lkml.kernel.org/r/1490046030-25862-1-git-send-email-tony.luck@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There is no need for the __ASSEMBLY__ ifdefery anymore since the
architecture level set code that deals with facility bits was
converted to C in the meantime.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use the actual size of the facility list array within the lowcore
structure for the MAX_FACILITY_BIT define instead of a comment which
states what this is good for. This makes it a bit harder to break
things.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Provide the remaining stsi information via debugfs files. This also
might be useful for debugging purposes.
Suggested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Provide the raw stsi 15,1,x data contents via debugfs. This makes it
much easier to debug unexpected scheduling domains on machines that
provide cpu topology information.
Therefore this file adds a new 's390/stsi' debugfs directory with a
file for each possible topology nesting level that is allowed by the
architecture. The files will be created regardless if the machine
supports all, or any, level. If a level is not supported, or no data
is available, user space can recognize this with a -EINVAL error code
when trying to read such data.
In addition a 'topology' symlink is created that points to the file
that contains the data that is used to create the scheduling domains.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Introduce a top-level 's390' directory which should be used when
adding new s390 specific debug feature files and/or directories.
This makes hopefully sure that the contents of the s390 directory will
be a bit more structured. Right now we have a couple of top-level
files where it is not easy to tell to which subsystem they belong to.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
User space needs some information about the secure key(s)
before actually invoking the pkey and/or paes funcionality.
This patch introduces a new ioctl API and in kernel API to
verify the the secure key blob and give back some
information about the key (type, bitsize, old MKVP).
Both APIs are described in detail in the header files
arch/s390/include/asm/pkey.h and arch/s390/include/uapi/asm/pkey.h.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
If running within a level 3 hypervisor, the hypervisor provides a
SYSIB block which contains a control program indentifier string. Use
this string instead of the simple KVM and z/VM strings only. In case
of z/VM this provides addtional information: the z/VM version.
The new string looks similar to this:
Hardware name: IBM 2964 N96 702 (z/VM 6.4.0)
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The arch description provided for the "Hardware name:" contains lots
of extra whitespace due to the way the SYSIB contents are defined
(strings aren't zero terminated).
This looks a bit odd and therefore remove the extra whitespace
characters. This also gives the opportunity to add more information,
if required, without hitting the magic 80 characters per line limit.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Allow compiler warnings again for the sysinfo file. Compiler warnings
were disabled when the bogomips calculation with math-emu code was
introduced ("[S390] Calibrate delay and bogomips.").
Since that code is gone, we can enable warnings again.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use MACHINE_FLAG_TOPOLOGY instead of MACHINE_HAS_TOPOLOGY when
clearing the bit that indicates if the machine provides topology
information (and if it should be used). Currently works anyway.
Fixes: 68cc795d1933 ("s390/topology: make "topology=off" parameter work")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use a single long value instead of a single element array to represent
the core mask. The array is a leftover from 32/31 bit code so we were
able to use bitops helper functions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The s390 specific little endian bitop macros are gone since a long time.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.
page_table_alloc then uses the flag for a single page allocation. This
means that this flag has never been actually useful here because it has
always been used only for PAGE_ALLOC_COSTLY requests.
An earlier attempt to remove the flag 10d58bf297e2 ("s390: get rid of
superfluous __GFP_REPEAT") has missed this one but the situation is very
same here.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Add a new line to /proc/cpuinfo which shows all available facilities
as reported by the stfle instruction:
> cat /proc/cpuinfo
...
facilities : 0 1 2 3 4 6 7 ...
...
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Same helper function like for_each_set_bit in generic code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
the KVM tree easier.
|
|
Commit af51160ebd3c ("s390/smp: initialize cpu_present_mask in
setup_arch") initializes the cpu_present_mask much earlier than
before. However the cpu detection code relies on the fact that iff
logical cpu 0 is marked present then also the corresponding physical
cpu address within the pcpu_devices array slot is valid.
Since commit 44fd22992cb7 ("[PATCH] Register the boot-cpu in the cpu
maps earlier") this assumption is not true anymore. The patch marks
logical cpu 0 as present in common code without that architecture code
had a chance to setup the logical to physical map.
With that change the cpu detection code assumes that the physical cpu
address of cpu 0 is also 0, which is not necessarily true.
Subsequently the physical cpu address of the ipl cpu will be mapped to
a different logical cpu. If that cpu is brought online later the ipl
cpu will send itself an initial cpu reset sigp signal. This in turn
completely resets the ipl cpu and the system stops working.
A dump of such a system looks like a "store status" has been
forgotten. But actually the kernel itself removed all traces which
would allow to easily tell what went wrong.
To fix this initialize the logical to physical cpu address already in
smp_setup_processor_id(). In addition remove the initialization of the
cpu_present_mask and cpu_online_mask for cpu 0, since that has already
been done. Also add a sanity check, just in case common code will be
changed again...
The problem can be easily reproduced within a z/VM guest:
> chcpu -d 0
> vmcp ipl
Fixes: af51160ebd3c ("s390/smp: initialize cpu_present_mask in setup_arch")
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Reorder the operations in decompress_kernel() to ensure initrd is moved
to a safe location before the bss section is zeroed.
During decompression bss can overlap with the initrd and this can
corrupt the initrd contents depending on the size of the compressed
kernel (which affects where the initrd is placed by the bootloader) and
the size of the bss section of the decompressor.
Also use the correct initrd size when checking for overlaps with
parmblock.
Fixes: 06c0dd72aea3 ([S390] fix boot failures with compressed kernels)
Cc: stable@vger.kernel.org
Reviewed-by: Joy Latten <joy.latten@canonical.com>
Reviewed-by: Vineetha HariPai <vineetha.hari.pai@canonical.com>
Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The OPP are declared as shared but no operating points are declared for
cpu1, 2 and 3. Thus, the following error happens during the boot:
cpu cpu1: dev_pm_opp_of_get_sharing_cpus: Couldn't find tcpu_dev node.
This patch applies the operating points to each cpu of the A33.
Fixes: 03749eb88e63 ("ARM: dts: sun8i: add opp-v2 table for A33")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This adds a new system call to enable the use of guarded storage for
user space processes. The system call takes two arguments, a command
and pointer to a guarded storage control block:
s390_guarded_storage(int command, struct gs_cb *gs_cb);
The second argument is relevant only for the GS_SET_BC_CB command.
The commands in detail:
0 - GS_ENABLE
Enable the guarded storage facility for the current task. The
initial content of the guarded storage control block will be
all zeros. After the enablement the user space code can use
load-guarded-storage-controls instruction (LGSC) to load an
arbitrary control block. While a task is enabled the kernel
will save and restore the current content of the guarded
storage registers on context switch.
1 - GS_DISABLE
Disables the use of the guarded storage facility for the current
task. The kernel will cease to save and restore the content of
the guarded storage registers, the task specific content of
these registers is lost.
2 - GS_SET_BC_CB
Set a broadcast guarded storage control block. This is called
per thread and stores a specific guarded storage control block
in the task struct of the current task. This control block will
be used for the broadcast event GS_BROADCAST.
3 - GS_CLEAR_BC_CB
Clears the broadcast guarded storage control block. The guarded-
storage control block is removed from the task struct that was
established by GS_SET_BC_CB.
4 - GS_BROADCAST
Sends a broadcast to all thread siblings of the current task.
Every sibling that has established a broadcast guarded storage
control block will load this control block and will be enabled
for guarded storage. The broadcast guarded storage control block
is used up, a second broadcast without a refresh of the stored
control block with GS_SET_BC_CB will not have any effect.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The calculation of the global physical address (GPA) on UV4 is
incorrect. The gnode_extra/upper global offset should only be
applied for fixed address space systems (UV1..3).
Tested-by: John Estabrook <john.estabrook@hpe.com>
Signed-off-by: Mike Travis <mike.travis@hpe.com>
Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Cc: John Estabrook <estabrook@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <russ.anderson@hpe.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170321231646.667689538@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.12
Cleanup:
* Drop superfluous status update for frequency override on various boards
* Always use status "okay" to enable devices on porger board
* Add INTC-SYS clock to device tree of various SoCs
* Tidyup Audio-DMAC channel for DVC on r8a779[013] SoCs
* Remove unit-address and reg from integrated cache on various SoCs
* Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS
* Fix SCIFB0 dmas indentation on r8a774[35] SoCs
Enhancements:
* Add watchdog timer to r7s72100 SoC
* Update sdhi clock bindings on r7s72100 SoC
* tag 'renesas-dt-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
ARM: dts: silk: Drop superfluous status update for frequency override
ARM: dts: alt: Drop superfluous status update for frequency override
ARM: dts: gose: Drop superfluous status update for frequency override
ARM: dts: porter: Drop superfluous status update for frequency override
ARM: dts: koelsch: Drop superfluous status updates for frequency overrides
ARM: dts: lager: Drop superfluous status update for frequency override
ARM: dts: marzen: Drop superfluous status update for frequency override
ARM: dts: bockw: Drop superfluous status update for frequency override
ARM: dts: porter: Always use status "okay" to enable devices
ARM: dts: r8a7793: Add INTC-SYS clock to device tree
ARM: dts: r8a7793: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7791: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7794: Add INTC-SYS clock to device tree
ARM: dts: r8a7792: Add INTC-SYS clock to device tree
ARM: dts: r8a7791: Add INTC-SYS clock to device tree
ARM: dts: r8a7790: Add INTC-SYS clock to device tree
ARM: dts: r8a73a4: Add INTC-SYS clock to device tree
ARM: dts: r7s72100: Add watchdog timer
ARM: dts: r8a7790: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7794: Remove unit-address and reg from integrated cache
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Renesas ARM64 Based SoC DT Updates for v4.12
Cleanup:
* Drop superfluous status update for frequency override from all
r8a779[56] boards
* Tidyup Audio-DMAC channel for DVC for r8a7795 SoC
* Remove unit-address and reg from integrated cache on r8a779[56] SoCs
Enhancements:
* Add all Cortex-A53 and Cortex-A57 CPU cores to r8a7796 SoC
* Add Cortex-A53 CPU cores to r8a7795 SoC
* Update memory node to 4 GiB map on h3ulcb board
* Upgrade to PSCI v1.0 to support Suspend-to-RAM on r8a779[56] SoCs
* Add SCIF1 (DEBUG1) to r8a7796/salvator-x board
* Add all SCIF and HSCIF nodes with DMA enabled to r8a7796 SoC
* Set drive-strength for ravb pins for r8a7795/salvator-x board
* Enable gigabit ethernet on r8a779[56]/salvator-x boards
* Enable I2C for DVFS device r8a779[56]/salvator-x boards
* tag 'renesas-arm64-dt-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (32 commits)
arm64: dts: r8a7796: salvator-x: Drop superfluous status update for frequency override
arm64: dts: m3ulcb: Drop superfluous status update for frequency override
arm64: dts: r8a7795: salvator-x: Drop superfluous status updates for frequency overrides
arm64: dts: h3ulcb: Drop superfluous status update for frequency override
arm64: dts: r8a7796: Add Cortex-A53 PMU node
arm64: dts: r8a7796: Add Cortex-A53 CPU cores
arm64: dts: r8a7796: Add CA53 L2 cache-controller node
arm64: dts: r8a7796: Add Cortex-A57 PMU node
arm64: dts: r8a7796: Add Cortex-A57 CPU cores
arm64: dts: r8a7795: Tidyup Audio-DMAC channel for DVC
arm64: dts: r8a7795: salvator-x: Set drive-strength for ravb pins
arm64: dts: r8a7796: Remove unit-address and reg from integrated cache
arm64: dts: r8a7795: Remove unit-addresses and regs from integrated caches
arm64: dts: r8a7796: Upgrade to PSCI v1.0 to support Suspend-to-RAM
arm64: dts: r8a7795: Upgrade to PSCI v1.0 to support Suspend-to-RAM
arm64: dts: r8a7795: Add Cortex-A53 PMU node
arm64: dts: r8a7795: Add Cortex-A53 CPU cores
arm64: dts: r8a7796: Enable HSCIF DMA
arm64: dts: r8a7796: salvator-x: add SCIF1 (DEBUG1)
arm64: dts: r8a7796: Enable SCIF DMA
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into fixes
Fixes for 4.11:
- Fix USB host for sama5d2
- Fix cpuidle on sama5
* tag 'at91-ab-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: pm: cpu_idle: switch DDR to power-down mode
Revert "ARM: at91/dt: sama5d2: Use new compatible for ohci node"
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.11
A bunch of device tree fixes for various boards / SoCs.
* tag 'sunxi-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sun8i: a23/a33: drop bl_en_pin GPIO pinmux in reference design DTSI
ARM: dts: sun7i: lamobo-r1: Fix CPU port RGMII settings
ARM: sun8i: Fix the mali clock rate
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.11:
- A fix to reboot hang seen on imx6sx-udoo-neo board, by removing
arm-supply and soc-supply and using LDO enabled mode.
* tag 'imx-fixes-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx-udoo-neo: Fix reboot hang
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The moxart interrupt line flags were not respected in previous
driver: instead of assigning them per-consumer, a fixes mask
was set in the controller.
With the migration to a standard Faraday driver we need to
set up and handle the consumer flags correctly. Also remove
the Moxart-specific flags when switching to using real consumer
flags.
Extend the register window to 0x100 bytes as we may have a few
more registers in there and it doesn't hurt.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
* shared/dt-symlinks:
arm64: dts: add arm/arm64 include symlinks
ARM: dts: add arm/arm64 include symlinks
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
* shared/dt-symlinks:
arm64: dts: add arm/arm64 include symlinks
ARM: dts: add arm/arm64 include symlinks
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Allow including of dtsi files in an architecture-independent manner.
Some dtsi files may be shared between architectures and one suggestion
was to have symlinks and let these includes get accessed via a
#include <arm64/foo.dtsi>
So add the necessary symlinks for arm32.
Suggested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Allow including of dtsi files in an architecture-independent manner.
Some dtsi files may be shared between architectures and one suggestion
was to have symlinks and let these includes get accessed via a
#include <arm64/foo.dtsi>
So add the necessary symlinks for arm32.
Suggested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
If scache.waysize is 0, r4k___flush_cache_all() will do nothing and
then cause bugs. BTW, though vcache.waysize isn't being used by now,
we also fix its calculation.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@caviumnetworks.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15756/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
On VTLB+FTLB platforms (such as Loongson-3A R2), FTLB's pagesize is
usually configured the same as PAGE_SIZE. In such a case, Huge page
entry is not suitable to write in FTLB.
Unfortunately, when a huge page is created, its page table entries
haven't created immediately. Then the TLB refill handler will fetch an
invalid page table entry which has no "HUGE" bit, and this entry may be
written to FTLB. Since it is invalid, TLB load/store handler will then
use tlbwi to write the valid entry at the same place. However, the
valid entry is a huge page entry which isn't suitable for FTLB.
Our solution is to modify build_huge_handler_tail. Flush the invalid
old entry (whether it is in FTLB or VTLB, this is in order to reduce
branches) and use tlbwr to write the valid new entry.
Signed-off-by: Rui Wang <wangr@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@caviumnetworks.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15754/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Loongson-3's micro TLB (ITLB) is not strictly a subset of JTLB. That
means: when a JTLB entry is replaced by hardware, there may be an old
valid entry exists in ITLB. So, a TLB miss exception may occur while
handle_ri_rdhwr() is running because it try to access EPC's content.
However, handle_ri_rdhwr() doesn't clear EXL, which makes a TLB Refill
exception be treated as a TLB Invalid exception and tlbp may fail. In
this case, if FTLB (which is usually set-associative instead of set-
associative) is enabled, a tlbp failure will cause an invalid tlbwi,
which will hang the whole system.
This patch rename handle_ri_rdhwr_vivt to handle_ri_rdhwr_tlbp and use
it for Loongson-3. It try to solve the same problem described as below,
but more straightforwards.
https://patchwork.linux-mips.org/patch/12591/
I think Loongson-2 has the same problem, but it has no FTLB, so we just
keep it as is.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Rui Wang <wangr@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@caviumnetworks.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15753/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Loongson-3A R2 and newer CPU have FTLB, but Config0.MT is 1, so add
MIPS_CPU_FTLB to the CPU options.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@caviumnetworks.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15752/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 08b3c894e565 ("MIPS: lantiq: Disable xbar fpi burst mode")
accidentally requested the resources from the pmu address region
instead of the xbar registers region, but the check for the return
value of request_mem_region() was wrong. Commit 98ea51cb0c8c ("MIPS:
Lantiq: Fix another request_mem_region() return code check") fixed the
check of the return value of request_mem_region() which made the kernel
panics.
This patch now makes use of the correct memory region for the cross bar.
Fixes: 08b3c894e565 ("MIPS: lantiq: Disable xbar fpi burst mode")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
Cc: james.hogan@imgtec.com
Cc: arnd@arndb.de
Cc: sergei.shtylyov@cogentembedded.com
Cc: john@phrozen.org
Cc: <stable@vger.kernel.org> # 4.4.x-
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15751
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The vpe_mask member of struct core_boot_config is of type atomic_t,
which is a 32bit type. In cps-vec.S this member was being retrieved by a
PTR_L macro, which on 64bit systems is a 64bit load. On little endian
systems this is OK, since the double word that is retrieved will have
the required less significant word in the correct position. However, on
big endian systems the less significant word of the load is retrieved
from address+4, and the more significant from address+0. The destination
register therefore ends up with the required word in the more
significant word
e.g. when starting the second VP of a big endian 64bit system, the load
PTR_L ta2, COREBOOTCFG_VPEMASK(a0)
ends up setting register ta2 to 0x0000000300000000
When this value is written to the CPC it is ignored, since it is
invalid to write anything larger than 4 bits. This results in any VP
other than VP0 in a core failing to start in 64bit big endian systems.
Change the load to a 32bit load word instruction to fix the bug.
Fixes: f12401d7219f ("MIPS: smp-cps: Pull boot config retrieval out of mips_cps_boot_vpes")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15787/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Hook up three pkey syscalls (which we don't implement) and the new statx
syscall, as has been done for arch/arm/.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
