| Age | Commit message (Collapse) | Author |
|---|
|
Cleanups to whitespace and add some comments. Reading through the delay
slot logic I noticed some things:
- Delay slot instructions were not indented
- Some comments are not lined up
- Use tabs and spaces consistent with other code
No functional change
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
This helps to suppress the vmlinux.lds file.
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
The generic memcpy routine provided in kernel does only byte copies.
Using word copies we can lower boot time and cycles spend in memcpy
quite significantly.
Booting on my de0 nano I see boot times go from 7.2 to 5.6 seconds.
The avg cycles in memcpy during boot go from 6467 to 1887.
I tested several algorithms (see code in previous patch mails)
The implementations I tested and avg cycles:
- Word Copies + Loop Unrolls + Non Aligned 1882
- Word Copies + Loop Unrolls 1887
- Word Copies 2441
- Byte Copies + Loop Unrolls 6467
- Byte Copies 7600
In the end I ended up going with Word Copies + Loop Unrolls as it
provides best tradeoff between simplicity and boot speedups.
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
This adds a hand-optimized assembler version of memset and sets
__HAVE_ARCH_MEMSET to use this version instead of the generic C
routine
Signed-off-by: Olof Kindgren <olof.kindgren@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
This patch adds basic support for the idle state of the cpu.
The patch overrides the regular idle function, enables the interupts,
checks for the power management unit and enables the cpu doze mode
if available.
Signed-off-by: Sebastian Macke <sebastian@macke.de>
[shorne@gmail.com: Fixed checkpatch, blankline after declarations]
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
The bits were swapped, as per spec and processor implementation the
power management present bit is 9 and PIC bit is 8. This patch brings
the definitions into spec.
Signed-off-by: Sebastian Macke <sebastian@macke.de>
[shorne@gmail.com: Added commit body]
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
This causes the build to fail when building with the or1k-musl-linux-
toolchain and it is not needed.
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Support for the futex_atomic_* operations by using the
load-link/store-conditional l.lwa/l.swa instructions.
Most openrisc cores provide these instructions now if not available,
emulation is provided.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: remove OPENRISC_HAVE_INST_LWA_SWA config suggesed by
Alan Cox https://lkml.org/lkml/2014/7/23/666]
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Using the l.lwa and l.swa atomic instruction pair.
Most openrisc processor cores provide these instructions now. If the
instructions are not available emulation is provided.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: remove OPENRISC_HAVE_INST_LWA_SWA config suggesed by
Alan Cox https://lkml.org/lkml/2014/7/23/666]
[shorne@gmail.com: expand to implement all ops suggested by Peter
Zijlstra https://lkml.org/lkml/2017/2/20/317]
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Optimized version that make use of the l.lwa and l.swa atomic instruction
pair.
Most openrisc cores provide these instructions now, if not available
emulation is provided.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: remove OPENRISC_HAVE_INST_LWA_SWA config suggesed by
Alan Cox https://lkml.org/lkml/2014/7/23/666]
[shorne@gmail.com: fixed unused calculated value compiler warning in
define cmpxchg]
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
This utilize the load-link/store-conditional l.lwa and l.swa
instructions to implement the atomic bitops.
When those instructions are not available emulation is provided.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: remove OPENRISC_HAVE_INST_LWA_SWA config suggesed by
Alan Cox https://lkml.org/lkml/2014/7/23/666, implement
test_and_change_bit]
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Patch "sparc64: Add 64K page size support"
unconditionally used __flush_huge_tsb_one_entry()
which is available only when hugetlb support is
enabled.
Another issue was incorrect TSB flushing for 64K
pages in flush_tsb_user().
Signed-off-by: Nitin Gupta <nitin.m.gupta@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we're updating a register's sys_val, we use arm64_ftr_value() to
find the new field value. We use cpuid_feature_extract_field() to find
the new value, but this implicitly assumes a 4-bit field, so we may
extract more bits than we mean to for fields like CTR_EL0.L1ip.
This affects update_cpu_ftr_reg(), where we may extract erroneous values
for ftr_cur and ftr_new. Depending on the additional bits extracted in
either case, we may erroneously detect that the value is mismatched, and
we'll try to compute a new safe value.
Dependent on these extra bits and feature type, arm64_ftr_safe_value()
may pessimistically select the always-safe value, or may erroneously
choose either the extracted cur or new value as the safe option. The
extra bits will subsequently be masked out in arm64_ftr_set_value(), so
we may choose a higher value, yet write back a lower one.
Fix this by passing the width down explicitly in arm64_ftr_value(), so
we always extract the correct amount.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This reverts commit 0bfc445dec9dd8130d22c9f4476eed7598524129.
When we change the permissions of regions mapped using contiguous
entries, the architecture requires us to follow a Break-Before-Make
strategy, breaking *all* associated entries before we can change any of
the following properties from the entries:
- presence of the contiguous bit
- output address
- attributes
- permissiones
Failure to do so can result in a number of problems (e.g. TLB conflict
aborts and/or erroneous results from TLB lookups).
See ARM DDI 0487A.k_iss10775, "Misprogramming of the Contiguous bit",
page D4-1762.
We do not take this into account when altering the permissions of kernel
segments in mark_rodata_ro(), where we change the permissions of live
contiguous entires one-by-one, leaving them transiently inconsistent.
This has been observed to result in failures on some fast model
configurations.
Unfortunately, we cannot follow Break-Before-Make here as we'd have to
unmap kernel text and data used to perform the sequence.
For the timebeing, revert commit 0bfc445dec9dd813 so as to avoid issues
resulting from this misuse of the contiguous bit.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <Will.Deacon@arm.com>
Cc: stable@vger.kernel.org # v4.10
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Commit 38fd94b0275c ("arm64: Work around Falkor erratum 1003") tried to
work around a hardware erratum, but actually caused a system crash of
its own during switch_mm:
cpu_do_switch_mm+0x20/0x40
efi_virtmap_load+0x34/0x40
virt_efi_get_next_variable+0x64/0xc8
efivar_init+0x8c/0x348
efisubsys_init+0xd4/0x270
do_one_initcall+0x80/0x110
kernel_init_freeable+0x19c/0x240
kernel_init+0x10/0x100
ret_from_fork+0x10/0x50
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
In cpu_do_switch_mm, x1 contains the mm_struct pointer, which needs to
be preserved by the pre_ttbr0_update_workaround macro rather than passed
as a temporary.
This patch clobbers x2 and x3 instead, keeping the mm_struct intact
after the workaround has run.
Fixes: 38fd94b0275c ("arm64: Work around Falkor erratum 1003")
Tested-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The BUG() macro's use of __builtin_unreachable() via the unreachable()
macro tells gcc that the instruction is a dead end, and that it's safe
to assume the current code path will not execute past the previous
instruction.
On x86, the BUG() macro is implemented with the 'ud2' instruction. When
objtool's branch analysis sees that instruction, it knows the current
code path has come to a dead end.
Peter Zijlstra has been working on a patch to change the WARN macros to
use 'ud2'. That patch will break objtool's assumption that 'ud2' is
always a dead end.
Generally it's best for objtool to avoid making those kinds of
assumptions anyway. The more ignorant it is of kernel code internals,
the better.
So create a more generic way for objtool to detect dead ends by adding
an annotation to the unreachable() macro. The annotation stores a
pointer to the end of the unreachable code path in an '__unreachable'
section. Objtool can read that section to find the dead ends.
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/41a6d33971462ebd944a1c60ad4bf5be86c17b77.1487712920.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Return a sensible value if TASK_SIZE if called from a kernel thread.
This gets us around an issue with copy_mount_options that does a magic
size calculation "TASK_SIZE - (unsigned long)data" while in a kernel
thread and data pointing to kernel space.
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch introduces a new in-kernel-crypto blockcipher
called 'paes' which implements AES with protected keys.
The paes blockcipher can be used similar to the aes
blockcipher but uses secure key material to derive the
working protected key and so offers an encryption
implementation where never a clear key value is exposed
in memory.
The paes module is only available for the s390 platform
providing a minimal hardware support of CPACF enabled
with at least MSA level 3. Upon module initialization
these requirements are checked.
Includes additional contribution from Harald Freudenberger.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.11.
Nothing too major, the tinydrm and mmu-less support should make
writing smaller drivers easier for some of the simpler platforms, and
there are a bunch of documentation updates.
Intel grew displayport MST audio support which is hopefully useful to
people, and FBC is on by default for GEN9+ (so people know where to
look for regressions). AMDGPU has a lot of fixes that would like new
firmware files installed for some GPUs.
Other than that it's pretty scattered all over.
I may have a follow up pull request as I know BenH has a bunch of AST
rework and fixes and I'd like to get those in once they've been tested
by AST, and I've got at least one pull request I'm just trying to get
the author to fix up.
Core:
- drm_mm reworked
- Connector list locking and iterators
- Documentation updates
- Format handling rework
- MMU-less support for fbdev helpers
- drm_crtc_from_index helper
- Core CRC API
- Remove drm_framebuffer_unregister_private
- Debugfs cleanup
- EDID/Infoframe fixes
- Release callback
- Tinydrm support (smaller drivers for simple hw)
panel:
- Add support for some new simple panels
i915:
- FBC by default for gen9+
- Shared dpll cleanups and docs
- GEN8 powerdomain cleanup
- DMC support on GLK
- DP MST audio support
- HuC loading support
- GVT init ordering fixes
- GVT IOMMU workaround fix
amdgpu/radeon:
- Power/clockgating improvements
- Preliminary SR-IOV support
- TTM buffer priority and eviction fixes
- SI DPM quirks removed due to firmware fixes
- Powerplay improvements
- VCE/UVD powergating fixes
- Cleanup SI GFX code to match CI/VI
- Support for > 2 displays on 3/5 crtc asics
- SI headless fixes
nouveau:
- Rework securre boot code in prep for GP10x secure boot
- Channel recovery improvements
- Initial power budget code
- MMU rework preperation
vmwgfx:
- Bunch of fixes and cleanups
exynos:
- Runtime PM support for MIC driver
- Cleanups to use atomic helpers
- UHD Support for TM2/TM2E boards
- Trigger mode fix for Rinato board
etnaviv:
- Shader performance fix
- Command stream validator fixes
- Command buffer suballocator
rockchip:
- CDN DisplayPort support
- IOMMU support for arm64 platform
imx-drm:
- Fix i.MX5 TV encoder probing
- Remove lower fb size limits
msm:
- Support for HW cursor on MDP5 devices
- DSI encoder cleanup
- GPU DT bindings cleanup
sti:
- stih410 cleanups
- Create fbdev at binding
- HQVDP fixes
- Remove stih416 chip functionality
- DVI/HDMI mode selection fixes
- FPS statistic reporting
omapdrm:
- IRQ code cleanup
dwi-hdmi bridge:
- Cleanups and fixes
adv-bridge:
- Updates for nexus
sii8520 bridge:
- Add interlace mode support
- Rework HDMI and lots of fixes
qxl:
- probing/teardown cleanups
ZTE drm:
- HDMI audio via SPDIF interface
- Video Layer overlay plane support
- Add TV encoder output device
atmel-hlcdc:
- Rework fbdev creation logic
tegra:
- OF node fix
fsl-dcu:
- Minor fixes
mali-dp:
- Assorted fixes
sunxi:
- Minor fix"
[ This was the "fixed" pull, that still had build warnings due to people
not even having build tested the result. I'm not a happy camper
I've fixed the things I noticed up in this merge. - Linus ]
* tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux: (1177 commits)
lib/Kconfig: make PRIME_NUMBERS not user selectable
drm/tinydrm: helpers: Properly fix backlight dependency
drm/tinydrm: mipi-dbi: Fix field width specifier warning
drm/tinydrm: mipi-dbi: Silence: ‘cmd’ may be used uninitialized
drm/sti: fix build warnings in sti_drv.c and sti_vtg.c files
drm/amd/powerplay: fix PSI feature on Polars12
drm/amdgpu: refuse to reserve io mem for split VRAM buffers
drm/ttm: fix use-after-free races in vm fault handling
drm/tinydrm: Add support for Multi-Inno MI0283QT display
dt-bindings: Add Multi-Inno MI0283QT binding
dt-bindings: display/panel: Add common rotation property
of: Add vendor prefix for Multi-Inno
drm/tinydrm: Add MIPI DBI support
drm/tinydrm: Add helper functions
drm: Add DRM support for tiny LCD displays
drm/amd/amdgpu: post card if there is real hw resetting performed
drm/nouveau/tmr: provide backtrace when a timeout is hit
drm/nouveau/pci/g92: Fix rearm
drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios
drm/nouveau/hwmon: expose power_max and power_crit
..
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink
misc register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and
zx2967)"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
soc: samsung: pmu: Add register defines for pad retention control
reset: make zx2967 explicitly non-modular
reset: core: fix reset_control_put
soc: samsung: pm_domains: Read domain name from the new label property
soc: samsung: pm_domains: Remove message about failed memory allocation
soc: samsung: pm_domains: Remove unused name field
soc: samsung: pm_domains: Use full names in subdomains registration log
sata: ahci-da850: un-hardcode the MPY bits
sata: ahci-da850: add a workaround for controller instability
sata: ahci: export ahci_do_hardreset() locally
sata: ahci-da850: implement a workaround for the softreset quirk
sata: ahci-da850: add device tree match table
sata: ahci-da850: get the sata clock using a connection id
soc: samsung: pmu: Remove duplicated define for ARM_L2_OPTION register
memory: atmel-ebi: Enable the SMC clock if specified
soc: samsung: pmu: Remove unused and duplicated defines
memory: atmel-ebi: Properly handle multiple reference to the same CS
memory: atmel-ebi: Fix the test to enable generic SMC logic
soc: samsung: pm_domains: Add new Exynos5433 compatible
soc: samsung: pmu: Add dummy support for Exynos5433 SoC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"ARM64 DT updates are fairly small this time, only two new SoCs and a
handful of new machines get added, all of them similar to other
hardware we already support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards:
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64:
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K:
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner:
- MMC, USB
ARM Juno:
- Coresight, STM
Broadcom:
- NS2 GICv2m irqchip and PCIe
Marvell:
- Armada 3700 SPI, I2C, ethernet switch
Mediatek:
- MT8173 thermal
NXP i.MX:
- LS1046A thermal
Qualcomm:
- coresight on MSM8916, HDMI, WCNSS, SCM
Renesas:
- r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip:
- thermal, eDP, pinctrl enhancements
Samsung:
- TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier:
- SD reset, eMMC controller
ZTE:
- oppv2 cpufreq"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (110 commits)
arm64: dts: qcom: Add msm8916 CoreSight components
arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon
arm64: allwinner: add BananaPi-M64 support
arm64: allwinner: a64: add UART1 pin nodes
arm64: allwinner: pine64: add MMC support
arm64: allwinner: a64: Increase the MMC max frequency
arm64: allwinner: a64: Add MMC pinctrl nodes
arm64: allwinner: a64: Add MMC nodes
dt-bindings: clockgen: Add compatible string for LS1012A
Documentation: DT: add LS1012A compatible for SCFG and DCFG
Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards
arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci
arm64: tegra: Use symbolic reset identifiers
arm64: dts: r8a7796: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: tidyup audma definition order
arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
arm64: dts: r8a7796: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add R-Car Gen3 thermal support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"A total of 380 patches this time, mostly adding support for more
hardware in the device tree descriptions. There is not much exciting
here for 4.11, but I've tried my best to condense the information from
the pull requests I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now gets
fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3:
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box:
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder:
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points:
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already supported
chips:
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP
architecture:
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of
Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero, all based on
Allwinner SoCs:
http://linux-sunxi.org/LicheePi_One
http://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform:
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless:
https://beagleboard.org/black-wireless
https://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module:
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam
i.Core:
http://www.opossom.com/english/index.html
http://www.savageboard.org/
http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ul
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
- Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas,
qcom, rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic, eeprom,
mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (380 commits)
ARM: dts: armada-385-linksys: fix DSA compatible property
ARM: dts: Fix typo in armada-xp-98dx4251
ARM: DTS: Fix register map for virt-capable GIC
dt-bindings: arm,gic: Fix binding example for a virt-capable GIC
ARM: dts: sun8i: sinlinx: Enable audio nodes
ARM: dts: sun8i: parrot: Enable audio nodes
ARM: dts: sun8i: Add audio codec, dai and card for A33
ARM: dts: Add EMAC AXI settings for Arria10
ARM: dts: am335x-chiliboard: Support charger
ARM: dts: am335x-chiliboard: Support power button
ARM: sun8i: dt: Add mali node
dt-bindings: gpu: Add Mali Utgard bindings
ARM: dts: stm32: Add I2C1 support for STM32429 eval board
ARM: dts: stm32: Add I2C1 support for STM32F429 SoC
ARM: dts: stm32: Use clock DT binding definition on stm32f429 family
dt-bindings: mfd: stm32f4: Add missing binding definition
dt-bindings: mfd: stm32f4: Fix STM32F4_X_CLOCK() macro
ARM: dts: stm32: Enable pwm1 and pwm3 for stm32f469-disco
ARM: dts: stm32: add Timers driver for stm32f429 MCU
ARM: dts: add the AB8500 sysclk to the device trees
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"Defconfig additions, removals, etc. Almost all of them just turn on
drivers that we want on some platform, usually after the driver has
been merged into mainline.
There is now a new defconfig file for tango4"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: multi_v7_defconfig: enable pstore configs
ARM: multi_v7_defconfig: enable some newly added crypto modules
ARM: davinci_all_defconfig: enable SATA modules
arm64: defconfig: enable CONFIG_MTD_NAND and CONFIG_MTD_NAND_DENALI_DT
arm64: defconfig: enable CONFIG_MTD_BLOCK
ARM: Import tango4_defconfig
ARM: omap2plus_defconfig: Enable support for RTC M41T80
ARM: omap2plus_defconfig: Enable support for micrell phys
ARM: vf610m4: defconfig: enable EXT4 filesystem
ARM: omap2plus_defconfig: Fix probe errors on UARTs 5 and 6
arm64: defconfig: Enable NUMA and NUMA_BALANCING
arm64: defconfig: enable SMMUv3 config
ARM: davinci_all_defconfig: enable iio
ARM: Keystone: Enable ARCH_HAS_RESET_CONTROLLER
ARM: configs: stm32: Add RTC support in STM32 defconfig
ARM: defconfig: qcom: add APQ8060 DragonBoard devices
ARM: qcom_defconfig: enable thermal sensors
ARM: qcom_defconfig: add ahci configs
ARM: qcom_defconfig: add pcie and atl1c ethernet configs
ARM: qcom_defconfig: add usb related configs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit updates from Arnd Bergmann:
"Changes to platform code for 64-bit ARM platforms, only trivial stuff
this time, a few defconfig changes to enable drivers, and a new entry
for the Cavium ThunderX2 platform"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add Cavium ThunderX2 entry
arm64: add ARCH_THUNDER2 to defconfig
arm64: add THUNDER2 processor family
MAINTAINERS: Extend ARM/Mediatek SoC support section
arm64: defconfig: enable CONFIG_MMC_SDHCI_CADENCE
arm64: defconfig: enable XORv2 for Marvell Armada 7K/8K
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"In the SoC branch we normally collect classic arch/arm/mach-*
contents, i.e. C code changes for SoC platforms. This release cycle
the diffstat is quite nice, in that we're removing 3x the amount of
code that's being added.
The main reason for this is that there's a removal of camera drivers
for Freescale i.MX chips (driver was removed so the device
registration isn't needed any more). There's also removal of display
initialization code for OMAP that is no longer needed.
The rest are mostly minor tweaks and cleanups; constification on
Samsung platforms, cleanup of ux500 platform data, purge of other
unused platform data/device seutp on i.MX and other good stuff.
New SoC support this cycle is for two Allwinner platforms, H2+ and
V3s"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
ARM: ux500: remove deleted file from Makefile
ARM: ep93xx: Disable TS-72xx watchdog before uncompressing
ARM: ux500: cut some platform data
MAINTAINERS: Update for the current location of the bcm2835 tree.
ARM: davinci: remove BUG_ON() from da850_register_sata()
ARM: davinci: da850: model the SATA refclk
ARM: davinci: da850: add con_id for the SATA clock
ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for SATA
arm: mvebu: support for SMP on 98DX3336 SoC
dt-bindings: video: exynos7-decon: Remove obsolete samsung,power-domain property
soc: dove: constify reset_control_ops structures
ARM: mv78xx0: fix possible PCI buffer overflow
MAINTAINERS: transfer maintainership for the EZX platform
ARM: shmobile: rcar-gen2: Add more register documentation
ARM: tegra: paz00: Fix __initdata placement
ARM: OMAP: clock: Remove unused mpurate cmdline option
ARM: davinci: add skeleton for pdata-quirks
arm: sunxi: add support for V3s SoC
ARM: OMAP2+: omap_hwmod: Add support for earlycon
arm: hisi: drop extern hip01_cpu_die
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"We sometimes collect non-critical fixes that come in during the later
part of the merge window in a branch for the next release instead, and
this is that contents for v4.11.
Most of these are OMAP fixes, dealing with OMAP36/37 detection, quirks
and setup. There's also some fixes for Davinci and a Kconfig fix for
SCPI to only enable on ARM{,64}"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
firmware: arm_scpi: Add hardware dependencies
ARM: OMAP3: Fix SoC detection of OMAP36/37 Family
ARM: OMAP5: Add HWMOD_SWSUP_SIDLE_ACT flag for UART
ARM: dts: Fix compatible for ti81xx uarts for 8250
ARM: dts: Fix am335x and dm814x scm syscon to probe children
ARM: OMAP2+: Fix init for multiple quirks for the same SoC
ARM: dts: Fix omap3 off mode pull defines
bus: da850-mstpri: fix my e-mail address
ARM: davinci: da850: fix da850_set_pll0rate()
ARM: davinci: da850: coding style fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add ASPM L1 substate support
- enable PCIe Extended Tags when supported
- configure PCIe MPS settings on iProc, Versatile, X-Gene, and Xilinx
- increase VPD access timeout
- add ACS quirks for Intel Union Point, Qualcomm QDF2400 and QDF2432
- use new pci_irq_alloc_vectors() in more drivers
- fix MSI affinity memory leak
- remove unused MSI interfaces and update documentation
- remove unused AER .link_reset() callback
- avoid pci_lock / p->pi_lock deadlock seen with perf
- serialize sysfs enable/disable num_vfs operations
- move DesignWare IP from drivers/pci/host/ to drivers/pci/dwc/ and
refactor so we can support both hosts and endpoints
- add DT ECAM-like support for HiSilicon Hip06/Hip07 controllers
- add Rockchip system power management support
- add Thunder-X cn81xx and cn83xx support
- add Exynos 5440 PCIe PHY support
* tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (93 commits)
PCI: dwc: Remove dependency of designware on CONFIG_PCI
PCI: dwc: Add CONFIG_PCIE_DW_HOST to enable PCI dwc host
PCI: dwc: Split pcie-designware.c into host and core files
PCI: dwc: designware: Fix style errors in pcie-designware.c
PCI: dwc: designware: Parse "num-lanes" property in dw_pcie_setup_rc()
PCI: dwc: all: Split struct pcie_port into host-only and core structures
PCI: dwc: designware: Get device pointer at the start of dw_pcie_host_init()
PCI: dwc: all: Rename cfg_read/cfg_write to read/write
PCI: dwc: all: Use platform_set_drvdata() to save private data
PCI: dwc: designware: Move register defines to designware header file
PCI: dwc: Use PTR_ERR_OR_ZERO to simplify code
PCI: dra7xx: Group PHY API invocations
PCI: dra7xx: Enable MSI and legacy interrupts simultaneously
PCI: dra7xx: Add support to force RC to work in GEN1 mode
PCI: dra7xx: Simplify probe code with devm_gpiod_get_optional()
PCI: Move DesignWare IP support to new drivers/pci/dwc/ directory
PCI: exynos: Support the PHY generic framework
Documentation: binding: Modify the exynos5440 PCIe binding
phy: phy-exynos-pcie: Add support for Exynos PCIe PHY
Documentation: samsung-phy: Add exynos-pcie-phy binding
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto update from Herbert Xu:
"API:
- Try to catch hash output overrun in testmgr
- Introduce walksize attribute for batched walking
- Make crypto_xor() and crypto_inc() alignment agnostic
Algorithms:
- Add time-invariant AES algorithm
- Add standalone CBCMAC algorithm
Drivers:
- Add NEON acclerated chacha20 on ARM/ARM64
- Expose AES-CTR as synchronous skcipher on ARM64
- Add scalar AES implementation on ARM64
- Improve scalar AES implementation on ARM
- Improve NEON AES implementation on ARM/ARM64
- Merge CRC32 and PMULL instruction based drivers on ARM64
- Add NEON acclerated CBCMAC/CMAC/XCBC AES on ARM64
- Add IPsec AUTHENC implementation in atmel
- Add Support for Octeon-tx CPT Engine
- Add Broadcom SPU driver
- Add MediaTek driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (142 commits)
crypto: xts - Add ECB dependency
crypto: cavium - switch to pci_alloc_irq_vectors
crypto: cavium - switch to pci_alloc_irq_vectors
crypto: cavium - remove dead MSI-X related define
crypto: brcm - Avoid double free in ahash_finup()
crypto: cavium - fix Kconfig dependencies
crypto: cavium - cpt_bind_vq_to_grp could return an error code
crypto: doc - fix typo
hwrng: omap - update Kconfig help description
crypto: ccm - drop unnecessary minimum 32-bit alignment
crypto: ccm - honour alignmask of subordinate MAC cipher
crypto: caam - fix state buffer DMA (un)mapping
crypto: caam - abstract ahash request double buffering
crypto: caam - fix error path for ctx_dma mapping failure
crypto: caam - fix DMA API leaks for multiple setkey() calls
crypto: caam - don't dma_map key for hash algorithms
crypto: caam - use dma_map_sg() return code
crypto: caam - replace sg_count() with sg_nents_for_len()
crypto: caam - check sg_count() return value
crypto: caam - fix HW S/G in ablkcipher_giv_edesc_alloc()
..
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Here is the update of sound bits for 4.11: again at this time, no big
changes in ALSA and ASoC core but only cosmetic changes like
consitifaction.
Meanwhile, quite a lot of developments are seen in a few driver side.
ALSA Core:
- Clean up, consitification of some ops
HD-audio:
- A slight behavior change of single_cmd option
- Quirks for AmigaOne X1000, Samsung Ativ Book 8, Dell AiO, ALC221
HP, and fixes for Lewisburg controller
- Realtek ALC299, ALC1220 codecs
Others:
- USB-audio: Tascam US-16x08 DSP mixer quirk
- Intel HDMI LPE audio support for Baytrail / Cherrytrail; this
contains some updates in drm/i915 for the new platform binding
ASoC:
- Lots of updates in Intel drivers, mostly for DisplayPort and HDMI
on Skylake and onwards, as well as more Baytrail / Cherrytrail
boards support
- Channel mapping support for HDMI
- Support for AllWinner A31 and A33, Everest Semiconductor ES8328,
Nuvoton NAU8540.
* tag 'sound-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (323 commits)
ALSA: usb-audio: Tidy up mixer_us16x08.c
ALSA: usb-audio: Fix memory leak and corruption in mixer_us16x08.c
ALSA: usb-audio: purge needless variable length array
ALSA: x86: hdmi: select CONFIG_SND_PCM
ALSA: x86: Don't enable runtime PM as default
ALSA: x86: Use runtime PM autosuspend
ALSA: usb-audio: localize function without external linkage
ALSA: usb-audio: localize one-referrer variable
ALSA: usb-audio: Tascam US-16x08 DSP mixer quirk
ALSA: emu10k1: constify snd_emux_operators structure
ASoC: sun4i-spdif: drop unnessary snd_soc_unregister_component()
ASoC: Intel: bxt: Add jack port initialize in bxt_rt298 machine
ASoC: nau8825: automatic BCLK and LRC divde in master mode
ASoC: hdac_hdmi: Add device id for Geminilake
ASoC: Intel: Skylake: Add Geminlake IDs
ASoC: rt298: Add DMI match for Geminilake reference platform
ASoC: Intel: Skylake: Check device type to get endpoint configuration
ASoC: Intel: bxt: Add jack port initialize in da7219_max98357a machine
ASoC: Intel: Skylake: Add jack port initialize in nau88l25_ssm4567 machine
ASoC: Intel: Skylake: Add jack port initialize in nau88l25_max98357a machine
...
|
|
In add_node_ranges() when memblock resize happens, the iterator keeps using
the previous freed array. This bug cause hangs on machine where there are
over 128 memory blocks during boot. For example, on machines where memory
interleaving is small.
The problem is seen on T4-4 because it cant have 2T of memory, and memory
is interleaved at 8G. So we have 2T/8G = 256 regions to set node IDs. The
starting size of regions array is 128. Thus, we have to double at least one
time (actually we have to double twice because some memory is already
reserved and thus we need more than 256 regions). We start using an
incorrect pointer to the array after the first doubling.
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Reviewed-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add_node_ranges() takes 2.6s - 3.6s per 1T of boot time. On machine with 6T
memory it takes 15.4s, on 32T it would take 82s-115s of boot time.
This function sets NUMA ids for memory blocks, and scans the whole memory a
page at a time to do so. But, we could use values in latency groups mask
and match to determine the boundaries without checking every single page.
With the fix the add_node_ranges() time is reduced from 15.4s down to 0.2s
on machine with 6T memory.
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Reviewed-by: Babu Moger <babu.moger@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch depends on:
[v6] sparc64: Multi-page size support
- Testing
Tested on Sonoma by running stream benchmark instance which allocated
48G worth of 64K pages.
boot params: default_hugepagesz=64K hugepagesz=64K hugepages=1310720
Signed-off-by: Nitin Gupta <nitin.m.gupta@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for using multiple hugepage sizes simultaneously
on mainline. Currently, support for 256M has been added which
can be used along with 8M pages.
Page tables are set like this (e.g. for 256M page):
VA + (8M * x) -> PA + (8M * x) (sz bit = 256M) where x in [0, 31]
and TSB is set similarly:
VA + (4M * x) -> PA + (4M * x) (sz bit = 256M) where x in [0, 63]
- Testing
Tested on Sonoma (which supports 256M pages) by running stream
benchmark instances in parallel: one instance uses 8M pages and
another uses 256M pages, consuming 48G each.
Boot params used:
default_hugepagesz=256M hugepagesz=256M hugepages=300 hugepagesz=8M
hugepages=10000
Signed-off-by: Nitin Gupta <nitin.m.gupta@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On panic, all other CPUs are stopped except the one which had
hit panic. To keep console alive, we need to migrate hvcons irq
to panicked CPU.
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CPU needs to be marked offline before stopping it. When not marked
offline, the xcall receives HV_EWOULDBLOCK and so assumes that not all
CPUs received the message, and retries. After 10000 retries, it finally
fails with fatal mondo timeout.
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When returning from the user probe code into userspace process, PC & NPC are
truncated to 32 bits.
Due to shared libraries getting loaded very high in the virtual address
space of
the process, placing a user probe inside a shared library makes the kernel
return into the process at the wrong address, causing it to seg'fault
most of
the time.
This patch prevents truncating PC and NPC.
Signed-off-by: Eric Saint Etienne <eric.saint.etienne@oracle.com>
Reviewed-by: David Aldridge <david.j.aldridge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently define macros referring to cpu_data if CONFIG_SMP is
defined, but only include the declaration if CONFIG_NUMA is defined.
Fixes: 541cc39433a8 ("sparc: fix a building error reported by kbuild")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The objects viking_ops, viking_sun4d_smp_ops and smp_cachetlb_ops of
type sparc32_cachetlb_ops are not modified anywhere after getting modified
in the init functions. Inside init their reference is also stored in a
pointer of type const struct sparc32_cachetlb_ops *. So these structures
are never modified after init, therefore add __ro_after to the declaration
of these structures.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introcudes a new kernel module pkey which is providing
protected key handling and management functions. The pkey API is
available within the kernel for other s390 specific code to create
and manage protected keys. Additionally the functions are exported
to user space via IOCTL calls. The implementation makes extensive
use of functions provided by the zcrypt device driver. For
generating protected keys from secure keys there is also a CEX
coprocessor card needed.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Play safe and purge all tlbs after the control registers that contain
the primary, secondary and home space asces have been validated.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
When validating register contents first validate control registers
since these control the availability of features later being
validated.
For example the control register 0 should be validated first, before
the additional floating point (AFP) registers are validated, since
control register 0 contains the AFP-register control bit.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Adding the PCKMO inline function and the function code definitions
for using the pckmo function to the cpacf header file.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
_SEGMENT_ENTRY_INVALID denotes the invalid bit in a segment table
entry whereas _SEGMENT_ENTRY_EMPTY means that the value of the whole
entry is only the invalid bit, as the entry is completely empty.
Therefore we use _SEGMENT_ENTRY_INVALID only to check and set the
invalid bit with bitwise operations. _SEGMENT_ENTRY_EMPTY is only used
to check for (un)equality.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This the s390 version of commit c1bd55f922a2d ("x86: opt into
HAVE_COPY_THREAD_TLS, for both 32-bit and 64-bit").
Simply use the tls system call argument instead of extracting the tls
argument by magic from the pt_regs structure.
See commit 3033f14ab78c3 ("clone: support passing tls argument via C
rather than pt_regs magic") for more background.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Unbalanced set_fs usages (e.g. early exit from a function and a
forgotten set_fs(USER_DS) call) may lead to a situation where the
secondary asce is the kernel space asce when returning to user
space. This would allow user space to modify kernel space at will.
This would only be possible with the above mentioned kernel bug,
however we can detect this and fix the secondary asce before returning
to user space.
Therefore a new TIF_ASCE_SECONDARY which is used within set_fs. When
returning to user space check if TIF_ASCE_SECONDARY is set, which
would indicate a bug. If it is set print a message to the console,
fixup the secondary asce, and then return to user space.
This is similar to what is being discussed for x86 and arm:
"[RFC] syscalls: Restore address limit after a syscall".
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This is just a preparation patch in order to keep the "restore address
space after syscall" patch small.
Rename CIF_ASCE to CIF_ASCE_PRIMARY to be unique and specific when
introducing a second CIF_ASCE_SECONDARY CIF flag.
Suggested-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Merge updates from Andrew Morton:
"142 patches:
- DAX updates
- various misc bits
- OCFS2 updates
- most of MM"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (142 commits)
mm/z3fold.c: limit first_num to the actual range of possible buddy indexes
mm: fix <linux/pagemap.h> stray kernel-doc notation
zram: remove obsolete sysfs attrs
mm/memblock.c: remove unnecessary log and clean up
oom-reaper: use madvise_dontneed() logic to decide if unmap the VMA
mm: drop unused argument of zap_page_range()
mm: drop zap_details::check_swap_entries
mm: drop zap_details::ignore_dirty
mm, page_alloc: warn_alloc nodemask is NULL when cpusets are disabled
mm: help __GFP_NOFAIL allocations which do not trigger OOM killer
mm, oom: do not enforce OOM killer for __GFP_NOFAIL automatically
mm: consolidate GFP_NOFAIL checks in the allocator slowpath
lib/show_mem.c: teach show_mem to work with the given nodemask
arch, mm: remove arch specific show_mem
mm, page_alloc: warn_alloc print nodemask
mm, page_alloc: do not report all nodes in show_mem
Revert "mm: bail out in shrink_inactive_list()"
mm, vmscan: consider eligible zones in get_scan_count
mm, vmscan: cleanup lru size claculations
mm, vmscan: do not count freed pages as PGDEACTIVATE
...
|
|
Pull KVM updates from Paolo Bonzini:
"4.11 is going to be a relatively large release for KVM, with a little
over 200 commits and noteworthy changes for most architectures.
ARM:
- GICv3 save/restore
- cache flushing fixes
- working MSI injection for GICv3 ITS
- physical timer emulation
MIPS:
- various improvements under the hood
- support for SMP guests
- a large rewrite of MMU emulation. KVM MIPS can now use MMU
notifiers to support copy-on-write, KSM, idle page tracking,
swapping, ballooning and everything else. KVM_CAP_READONLY_MEM is
also supported, so that writes to some memory regions can be
treated as MMIO. The new MMU also paves the way for hardware
virtualization support.
PPC:
- support for POWER9 using the radix-tree MMU for host and guest
- resizable hashed page table
- bugfixes.
s390:
- expose more features to the guest
- more SIMD extensions
- instruction execution protection
- ESOP2
x86:
- improved hashing in the MMU
- faster PageLRU tracking for Intel CPUs without EPT A/D bits
- some refactoring of nested VMX entry/exit code, preparing for live
migration support of nested hypervisors
- expose yet another AVX512 CPUID bit
- host-to-guest PTP support
- refactoring of interrupt injection, with some optimizations thrown
in and some duct tape removed.
- remove lazy FPU handling
- optimizations of user-mode exits
- optimizations of vcpu_is_preempted() for KVM guests
generic:
- alternative signaling mechanism that doesn't pound on
tsk->sighand->siglock"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (195 commits)
x86/kvm: Provide optimized version of vcpu_is_preempted() for x86-64
x86/paravirt: Change vcp_is_preempted() arg type to long
KVM: VMX: use correct vmcs_read/write for guest segment selector/base
x86/kvm/vmx: Defer TR reload after VM exit
x86/asm/64: Drop __cacheline_aligned from struct x86_hw_tss
x86/kvm/vmx: Simplify segment_base()
x86/kvm/vmx: Get rid of segment_base() on 64-bit kernels
x86/kvm/vmx: Don't fetch the TSS base from the GDT
x86/asm: Define the kernel TSS limit in a macro
kvm: fix page struct leak in handle_vmon
KVM: PPC: Book3S HV: Disable HPT resizing on POWER9 for now
KVM: Return an error code only as a constant in kvm_get_dirty_log()
KVM: Return an error code only as a constant in kvm_get_dirty_log_protect()
KVM: Return directly after a failed copy_from_user() in kvm_vm_compat_ioctl()
KVM: x86: remove code for lazy FPU handling
KVM: race-free exit from KVM_RUN without POSIX signals
KVM: PPC: Book3S HV: Turn "KVM guest htab" message into a debug message
KVM: PPC: Book3S PR: Ratelimit copy data failure error messages
KVM: Support vCPU-based gfn->hva cache
KVM: use separate generations for each address space
...
|
|
Linux 4.10-rc8
Backmerge Linus rc8 to fix some conflicts, but also
to avoid pulling it in via a fixes pull from someone.
|
|
There's no users of zap_page_range() who wants non-NULL 'details'.
Let's drop it.
Link: http://lkml.kernel.org/r/20170118122429.43661-3-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
