| Age | Commit message (Collapse) | Author |
|---|
|
The "L" AArch64 machine constraint, which we use for the "old" value in
an LL/SC cmpxchg(), generates an immediate that is suitable for a 64-bit
logical instruction. However, for cmpxchg() operations on types smaller
than 64 bits, this constraint can result in an invalid instruction which
is correctly rejected by GAS, such as EOR W1, W1, #0xffffffff.
Whilst we could special-case the constraint based on the cmpxchg size,
it's far easier to change the constraint to "K" and put up with using
a register for large 64-bit immediates. For out-of-line LL/SC atomics,
this is all moot anyway.
Reported-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Our percpu code is a bit of an inconsistent mess:
* It rolls its own xchg(), but reuses cmpxchg_local()
* It uses various different flavours of preempt_{enable,disable}()
* It returns values even for the non-returning RmW operations
* It makes no use of LSE atomics outside of the cmpxchg() ops
* There are individual macros for different sizes of access, but these
are all funneled through a switch statement rather than dispatched
directly to the relevant case
This patch rewrites the per-cpu operations to address these shortcomings.
Whilst the new code is a lot cleaner, the big advantage is that we can
use the non-returning ST- atomic instructions when we have LSE.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The CAS instructions implicitly access only the relevant bits of the "old"
argument, so there is no need for explicit masking via type-casting as
there is in the LL/SC implementation.
Move the casting into the LL/SC code and remove it altogether for the LSE
implementation.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Our atomic instructions (either LSE atomics of LDXR/STXR sequences)
natively support byte, half-word, word and double-word memory accesses
so there is no need to mask the data register prior to being stored.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Earlier attempt to move am335x mcasp to probe with ti-sysc
interconnect target module caused audio to stop working and and
the dts changes were reverted by commit 5d2632a577ba ("ARM: dts:
Revert am335x mcasp ti-sysc changes").
Turns out we were missing the l3 data port ranges for mcasp. This
caused mcasp dma to attempt to use wrong port address. So let's
try again essentially reverting the earlier revert and adding the
missing l3 data port ranges.
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
It was noticed that unbinding and rebinding the KSZ8851 ethernet
resulted in the driver reporting "failed to read device ID" at probe.
Probing the reset line with a 'scope while repeatedly attempting to
bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is
constantly held at zero, meaning the device is held in reset, and
does not respond on the SPI bus.
Experimentation with the startup delay on the regulator set to 50ms
shows that the reset is positively released after 20ms.
Schematics for this board are not available, and the traces are buried
in the inner layers of the board which makes tracing where the RSTN pin
extremely difficult. We can only guess that the RSTN pin is wired to a
reset generator chip driven off the ethernet supply, which fits the
observed behaviour.
Include this delay in the regulator startup delay - effectively
treating the reset as a "supply stable" indicator.
This can not be modelled as a delay in the KSZ8851 driver since the
reset generation is board specific - if the RSTN pin had been wired to
a GPIO, reset could be released earlier via the already provided support
in the KSZ8851 driver.
This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based
on Blaze schematics that should be very close to SDP4430:
TPS22902YFPR is used as the regulator switch (gpio48 controlled):
Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV.
(SCH Note: Threshold set at 90%. Vsense: 0.405V).
According to the TPS3808 data sheet the RESET delay time when Ct is
open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated with notes from schematics from Peter]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When a micro SD card is inserted in the PDU001 card cage, the card
detection switch is opened and the corresponding GPIO input is driven
by a pull-up. Hence change the active level of the card detection
input from low to high.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
Since commit 1137ceee76ba ("ARM: OMAP1: ams-delta: Don't request unused
GPIOs"), on-board audio has appeared muted. Believed to be unused GPIO
pin "hookflash1", apparently set high regardless of the corresponding
bit of "latch2" port attempted to be set low during .init_machine(),
has been identified as the reason.
According to Amstrad E3 wiki, the purpose of the pin hasn't been
clearly identified. Original Amstrad software used to produce a high
pulse on it when the phone was taken off hook or recall was pressed.
With the current finding, we can assume the pin provides a kind of
audio mute function.
Proper resolution of the issue should be done in two steps:
- resolution of an issue with the pin state not reflecting the value
the corresponding bit of the port was attempted to be initialized
with,
- extension of on-board audio driver with a new control.
For now, rename the pin to "audio_mute" to reflect its function and,
as a quick fix, hogg it as output low so on-board audio can produce
audible sound again.
Fixes: 1137ceee76ba ("ARM: OMAP1: ams-delta: Don't request unused GPIOs")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP5's Super-Speed USB port has a software mailbox register
that needs to be fed with VBUS and ID events from an external
VBUS/ID comparator.
Without this, Host role will not work correctly.
Fixes: 656c1a65ab55 ("ARM: dts: omap5: enable OTG role for DWC3 controller")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Since commit 3b8c9f1cdfc50 ("arm64: IPI each CPU after invalidating the
I-cache for kernel mappings"), a call to flush_icache_range() will use
an IPI to cross-call other online CPUs so that any stale instructions
are flushed from their pipelines. This triggers a WARN during the
hibernation resume path, where flush_icache_range() is called with
interrupts disabled and is therefore prone to deadlock:
| Disabling non-boot CPUs ...
| CPU1: shutdown
| psci: CPU1 killed.
| CPU2: shutdown
| psci: CPU2 killed.
| CPU3: shutdown
| psci: CPU3 killed.
| WARNING: CPU: 0 PID: 1 at ../kernel/smp.c:416 smp_call_function_many+0xd4/0x350
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.20.0-rc4 #1
Since all secondary CPUs have been taken offline prior to invalidating
the I-cache, there's actually no need for an IPI and we can simply call
__flush_icache_range() instead.
Cc: <stable@vger.kernel.org>
Fixes: 3b8c9f1cdfc50 ("arm64: IPI each CPU after invalidating the I-cache for kernel mappings")
Reported-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Now that kexec_walk_memblock() can do the crash-kernel placement itself
architectures that don't support kdump via kexe_file_load() need to
explicitly forbid it.
We don't support this on arm64 until the kernel can add the elfcorehdr
and usable-memory-range fields to the DT. Without these the crash-kernel
overwrites the previous kernel's memory during startup.
Add a check to refuse crash image loading.
Reviewed-by: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
"arm,cortex-a15-pmu" is not a valid fallback compatible string for an
Cortex-A7 PMU, so drop it.
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The intention in the previous patch was to only place the processor
tables in the .rodata section if big.Little was being built and we
wanted the branch target hardening, but instead (due to the way it
was tested) it ended up always placing the tables into the .rodata
section.
Although harmless, let's correct this anyway.
Fixes: 3a4d0c2172bc ("ARM: ensure that processor vtables is not lost after boot")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The asm-generic/preempt.h implementation doesn't make use of the
PREEMPT_NEED_RESCHED flag, since this can interact badly with load/store
architectures which rely on the preempt_count word being unchanged across
an interrupt.
However, since we're a 64-bit architecture and the preempt count is
only 32 bits wide, we can simply pack it next to the resched flag and
load the whole thing in one go, so that a dec-and-test operation doesn't
need to load twice.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
PREEMPT_NEED_RESCHED is never used directly, so move it into the arch
code where it can potentially be implemented using either a different
bit in the preempt count or as an entirely separate entity.
Cc: Robert Love <rml@tech9.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Fix an off-by-one error in the memory resource range. This resource is
used to determine the address range of the memory to be hot-plugged as
ZONE_DEVICE memory. The current end address results in the kernel
attempting to map an additional memblock and the hypervisor may reject
the mapping resulting in the entire hot-plug failing.
Fixes: b5beae5e224f ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Making PAPR_SCM select LIBNVDIMM results in circular dependencies in
Kconfig when another symbol depends on it. Fix this by replacing the
select with a depends.
Fixes: b5beae5e224f ("powerpc/pseries: Add driver for PAPR SCM regions")
Reported-by: Alastair D'Silva <alastair@d-silva.org>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Now that there are different variants of pt_regs for userspace and
kernel, the uapi for the BPF_PROG_TYPE_PERF_EVENT program type must be
changed by exporting the user_pt_regs structure instead of the pt_regs
structure that is in-kernel only.
Fixes: 002af9391bfb ("powerpc: Split user/kernel definitions of struct pt_regs")
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Technically the display-hub driver could access registers via the
specified region, though it practice it will do so via the display
controllers' register regions.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Technically the display-hub driver could access registers via the
specified region, though it practice it will do so via the display
controllers' register regions.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Amstrad Delta NAND driver now uses GPIO API for data I/O so there is no
need to assign memory I/O resource to the device any longer. Drop it.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Data port used by Amstrad Delta NAND driver is actually an OMAP MPUIO
device, already under control of gpio-omap driver. The NAND driver
gets access to the port by ioremapping it and performs read/write
operations. That is done without any proteciton from other users
legally manipulating the port pins over GPIO API.
The plan is to convert the driver to access the port over GPIO consumer
API. Before that is implemented, the driver can already obtain
exclusive access to the port by requesting an array of its GPIO
descriptors.
Add respective entries to the NAND GPIO lookup table.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The RTC module on the A64 was claimed to be the same as on the A31, when
in fact it is not. It is actually compatible to the H3's RTC. The A64's
RTC has some extra crypto-related registers which the H3's does not, but
the exact function of these is not clear.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The device node for the internal oscillator is
removed, as it is internalized into the RTC device. Clock references to
the IOSC and LOSC are also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The R40 has an RTC hardware block, which has additional registers
that are not related to RTC or clock functions, and is otherwise
compatible with the H3's RTC.
Add a device node for it, and fix up any references to the LOSC.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The RTC module on the H3 was claimed to be the same as on the A31, when
in fact it is not. The A31 does not have an RTC external clock output,
and its internal RC oscillator's average clock rate is not in the same
range. The H5's RTC has some extra crypto-related registers compared to
the H3. Their exact functions are not clear. Also the RTC-VIO regulator
has different settings.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The device node for the internal oscillator is
removed, as it is internalized into the RTC device. Clock references to
the IOSC and LOSC are also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The RTC module on the A23 was claimed to be the same as on the A31, when
in fact it is not. The A31 does not have an RTC external clock output,
and its internal RC oscillator's average clock rate is not in the same
range. The A33's RTC is the same as the A23.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The register range is also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Pull ARM spectre fix from Russell King:
"Exynos folk noticed that CPU hotplug wasn't working with their kernel
configuration, and have tested this as fixing the problem"
* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: ensure that processor vtables is not lost after boot
|
|
Pull ARM fixes from Russell King:
"Some small fixes that have been accumulated:
- Chris Cole noticed that in a SMP environment, the DMA cache
coherence handling can produce undesirable results in a corner
case
- Propagate that fix for ARMv7M as well
- Fix a false positive with source fortification
- Fix an uninitialised return that Nathan Jones spotted"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8816/1: dma-mapping: fix potential uninitialized return
ARM: 8815/1: V7M: align v7m_dma_inv_range() with v7 counterpart
ARM: 8814/1: mm: improve/fix ARM v7_dma_inv_range() unaligned address handling
ARM: 8806/1: kprobes: Fix false positive with FORTIFY_SOURCE
|
|
Arndale boards have wires for DSI and eDP panels, but in-kernel support
for eDP panels is broken for long time and breaks display support even on
boards with DSI panels.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add RTC and charger drivers for MAX8998 chip used on Samsung UniversalC210
board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Enable IOMMU for all SDHCI controllers in Tegra186.
Signed-off-by: Krishna Reddy <vdumpa@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The HDA controller can be used for audio playback over HDMI.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The CEC controller found on Tegra194 can be used to control consumer
devices using the HDMI CEC pin.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Enable the HDA controller on Jetson Xavier so that it can be used for
audio playback over HDMI.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The HDA controller found on Tegra194 can be used for audio playback over
HDMI.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The CEC controller found on Tegra186 can be used to control consumer
devices using the HDMI CEC pin.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Enable the HDA controller on Jetson TX2 so that it can be used for audio
playback over HDMI.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The HDA controller found on Tegra186 can be used for audio playback over
HDMI.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Pull C-SKY fixes from Guo Ren:
- bugfix for tlb_get_pgd() error
- update MAINTAINERS file for C-SKY drivers
* tag 'csky-4.20-rc6' of github.com:c-sky/csky-linux:
csky: bugfix tlb_get_pgd error.
MAINTAINERS: add maintainer for C-SKY drivers
|
|
Add hstate for each supported hugepage size using arch initcall.
* no hugepage parameters
Without hugepage parameters, only a default hugepage size is
available for dynamic allocation. It's different, for example, from
x86_64 and sparc64 where all supported hugepage sizes are available.
* only default_hugepagesz= is specified and set not to HPAGE_SIZE
In spite of the fact that default_hugepagesz= is set to a valid
hugepage size, it's treated as unsupported and reverted to
HPAGE_SIZE. Such behaviour is also different from x86_64 and
sparc64.
Acked-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Tom Saeger <tom.saeger@oracle.com>
Signed-off-by: Dmitry Klochkov <dmitry.klochkov@oracle.com>
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This is a NEON acceleration method that can improve
performance by approximately 20%. I got the following
data from the centos 7.5 on Huawei's HISI1616 chip:
[ 93.837726] xor: measuring software checksum speed
[ 93.874039] 8regs : 7123.200 MB/sec
[ 93.914038] 32regs : 7180.300 MB/sec
[ 93.954043] arm64_neon: 9856.000 MB/sec
[ 93.954047] xor: using function: arm64_neon (9856.000 MB/sec)
I believe this code can bring some optimization for
all arm64 platform. thanks for Ard Biesheuvel's suggestions.
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
In a way similar to ARM commit 09096f6a0ee2 ("ARM: 7822/1: add workaround
for ambiguous C99 stdint.h types"), this patch redefines the macros that
are used in stdint.h so its definitions of uint64_t and int64_t are
compatible with those of the kernel.
This patch comes from: https://patchwork.kernel.org/patch/3540001/
Wrote by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
We mark this file as a private file and don't have to override asm/types.h
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The comment about SYS_MEMBARRIER_SYNC_CORE relying on ERET being
context-synchronizing is confusing and misplaced with kpti. Given that
this is already documented under Documentation/ (see arch-support.txt
for membarrier), remove the comment altogether.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Some CPUs can speculate past an ERET instruction and potentially perform
speculative accesses to memory before processing the exception return.
Since the register state is often controlled by a lower privilege level
at the point of an ERET, this could potentially be used as part of a
side-channel attack.
This patch emits an SB sequence after each ERET so that speculation is
held up on exception return.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We currently use a DSB; ISB sequence to inhibit speculation in set_fs().
Whilst this works for current CPUs, future CPUs may implement a new SB
barrier instruction which acts as an architected speculation barrier.
On CPUs that support it, patch in an SB; NOP sequence over the DSB; ISB
sequence and advertise the presence of the new instruction to userspace.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Marek Szyprowski reported problems with CPU hotplug in current kernels.
This was tracked down to the processor vtables being located in an
init section, and therefore discarded after kernel boot, despite being
required after boot to properly initialise the non-boot CPUs.
Arrange for these tables to end up in .rodata when required.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 383fb3ee8024 ("ARM: spectre-v2: per-CPU vtables to work around big.Little systems")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
These interrupt functions are already non-attachable by kprobes.
Blacklist them explicitly so that they can show up in
/sys/kernel/debug/kprobes/blacklist and tools like BCC can use this
additional information.
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yonghong Song <yhs@fb.com>
Link: http://lkml.kernel.org/r/20181206095648.GA8249@Dell
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
setup_dtb() is a little difficult to read. This is largely because it
duplicates the FDT -> Linux errno conversion for every intermediate
return value, but also because of silly cosmetic things like naming
and formatting.
Given that this is all brand new, refactor the function to get us off on
the right foot.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Adding "kaslr-seed" to dtb enables triggering kaslr, or kernel virtual
address randomization, at secondary kernel boot. We always do this as
it will have no harm on kaslr-incapable kernel.
We don't have any "switch" to turn off this feature directly, but still
can suppress it by passing "nokaslr" as a kernel boot argument.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
[will: Use rng_is_initialized()]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
