| Age | Commit message (Collapse) | Author |
|---|
|
Since commit "efcac65 powerpc: Per process DSCR + some fixes (try#4)"
it is no longer possible to set the DSCR on a per-CPU basis.
The old behaviour was to minipulate the DSCR SPR directly but this is no
longer sufficient: the value is quickly overwritten by context switching.
This patch stores the per-CPU DSCR value in a kernel variable rather than
directly in the SPR and it is used whenever a process has not set the DSCR
itself. The sysfs interface (/sys/devices/system/cpu/cpuN/dscr) is unchanged.
Writes to the old global default (/sys/devices/system/cpu/dscr_default)
now set all of the per-CPU values and reads return the last written value.
The new per-CPU default is added to the paca_struct and is used everywhere
outside of sysfs.c instead of the old global default.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Split the __SYSFS_SPRSETUP macro into two parts so that registers requiring
custom read and write functions can use common code for their show and store
functions.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Cleaning up inconsistent NULL checks.
There is otherwise a risk of a possible null pointer dereference.
Was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit 32e45ff43eaf5c17f changed the default value of
RECLAIM_DISTANCE to 30. However the comment around arch
specifc definition of RECLAIM_DISTANCE is not updated to
reflect the same. Correct the value mentioned in the comment.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: KOSAKI Motohiro <Kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Upcoming POWER8 chips support a concept called split core. This is where the
core can be split into subcores that although not full cores, are able to
appear as full cores to a guest.
The splitting & unsplitting procedure is mildly complicated, and explained at
length in the comments within the patch.
One notable detail is that when splitting or unsplitting we need to pull
offline cpus out of their offline state to do work as part of the procedure.
The interface for changing the split mode is via a sysfs file, eg:
$ echo 2 > /sys/devices/system/cpu/subcores_per_core
Currently supported values are '1', '2' and '4'. And indicate respectively that
the core should be unsplit, split in half, and split in quarters. These modes
correspond to threads_per_subcore of 8, 4 and 2.
We do not allow changing the split mode while KVM VMs are active. This is to
prevent the value changing while userspace is configuring the VM, and also to
prevent the mode being changed in such a way that existing guests are unable to
be run.
CPU hotplug fixes by Srivatsa. max_cpus fixes by Mahesh. cpuset fixes by
benh. Fix for irq race by paulus. The rest by mikey and mpe.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
To support split core on POWER8 we need to modify various parts of the
KVM code to use threads_per_subcore instead of threads_per_core. On
systems that do not support split core threads_per_subcore ==
threads_per_core and these changes are a nop.
We use threads_per_subcore as the value reported by KVM_CAP_PPC_SMT.
This communicates to userspace that guests can only be created with
a value of threads_per_core that is less than or equal to the current
threads_per_subcore. This ensures that guests can only be created with a
thread configuration that we are able to run given the current split
core mode.
Although threads_per_subcore can change during the life of the system,
the commit that enables that will ensure that threads_per_subcore does
not change during the life of a KVM VM.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Alexander Graf <agraf@suse.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
To support split core we need to change the check in __cpu_up() that
determines if a cpu is allowed to come online.
Currently we refuse to online cpus which are not the primary thread
within their core.
On POWER8 with split core support this check needs to instead refuse to
online cpus which are not the primary thread within their *sub* core.
On POWER7 and other systems that do not support split core,
threads_per_subcore == threads_per_core and so the check is equivalent.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On POWER8 we have a new concept of a subcore. This is what happens when
you take a regular core and split it. A subcore is a grouping of two or
four SMT threads, as well as a handfull of SPRs which allows the subcore
to appear as if it were a core from the point of view of a guest.
Unlike threads_per_core which is fixed at boot, threads_per_subcore can
change while the system is running. Most code will not want to use
threads_per_subcore.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
To support split core we need to be able to force all secondaries into
nap, so the core can detect they are idle and do an unsplit.
Currently power7_nap() will return without napping if there is an irq
pending. We want to ignore the pending irq and nap anyway, we will deal
with the interrupt later.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
As part of the support for split core on POWER8, we want to be able to
block splitting of the core while KVM VMs are active.
The logic to do that would be exactly the same as the code we currently
have for inhibiting onlining of secondaries.
Instead of adding an identical mechanism to block split core, rework the
secondary inhibit code to be a "HV KVM is active" check. We can then use
that in both the cpu hotplug code and the upcoming split core code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Alexander Graf <agraf@suse.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Based off fd1197f1 for ia64, enable CONFIG_HAVE_MEMORYLESS_NODES if
NUMA. Initialize the local memory node in start_secondary.
With this commit and the preceding to enable
CONFIG_USER_PERCPU_NUMA_NODE_ID, which is a prerequisite, in a PowerKVM
guest with the following topology:
numactl --hardware
available: 3 nodes (0-2)
node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70
71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94
95 96 97 98 99
node 0 size: 1998 MB
node 0 free: 521 MB
node 1 cpus: 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114
115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132
133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150
151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168
169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186
187 188 189 190 191 192 193 194 195 196 197 198 199
node 1 size: 0 MB
node 1 free: 0 MB
node 2 cpus:
node 2 size: 2039 MB
node 2 free: 1739 MB
node distances:
node 0 1 2
0: 10 40 40
1: 40 10 40
2: 40 40 10
the unreclaimable slab is reduced by close to 130M:
Before:
Slab: 418176 kB
SReclaimable: 26624 kB
SUnreclaim: 391552 kB
After:
Slab: 298944 kB
SReclaimable: 31744 kB
SUnreclaim: 267200 kB
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Based off 3bccd996 for ia64, convert powerpc to use the generic per-CPU
topology tracking, specifically:
initialize per cpu numa_node entry in start_secondary
remove the powerpc cpu_to_node()
define CONFIG_USE_PERCPU_NUMA_NODE_ID if NUMA
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Merge the binutils and kexec fixes.
|
|
If we try to perform a kexec when the machine is in ST (Single-Threaded) mode
(ppc64_cpu --smt=off), the kexec operation doesn't succeed properly, and we
get the following messages during boot:
[ 0.089866] POWER8 performance monitor hardware support registered
[ 0.089985] power8-pmu: PMAO restore workaround active.
[ 5.095419] Processor 1 is stuck.
[ 10.097933] Processor 2 is stuck.
[ 15.100480] Processor 3 is stuck.
[ 20.102982] Processor 4 is stuck.
[ 25.105489] Processor 5 is stuck.
[ 30.108005] Processor 6 is stuck.
[ 35.110518] Processor 7 is stuck.
[ 40.113369] Processor 9 is stuck.
[ 45.115879] Processor 10 is stuck.
[ 50.118389] Processor 11 is stuck.
[ 55.120904] Processor 12 is stuck.
[ 60.123425] Processor 13 is stuck.
[ 65.125970] Processor 14 is stuck.
[ 70.128495] Processor 15 is stuck.
[ 75.131316] Processor 17 is stuck.
Note that only the sibling threads are stuck, while the primary threads (0, 8,
16 etc) boot just fine. Looking closer at the previous step of kexec, we observe
that kexec tries to wakeup (bring online) the sibling threads of all the cores,
before performing kexec:
[ 9464.131231] Starting new kernel
[ 9464.148507] kexec: Waking offline cpu 1.
[ 9464.148552] kexec: Waking offline cpu 2.
[ 9464.148600] kexec: Waking offline cpu 3.
[ 9464.148636] kexec: Waking offline cpu 4.
[ 9464.148671] kexec: Waking offline cpu 5.
[ 9464.148708] kexec: Waking offline cpu 6.
[ 9464.148743] kexec: Waking offline cpu 7.
[ 9464.148779] kexec: Waking offline cpu 9.
[ 9464.148815] kexec: Waking offline cpu 10.
[ 9464.148851] kexec: Waking offline cpu 11.
[ 9464.148887] kexec: Waking offline cpu 12.
[ 9464.148922] kexec: Waking offline cpu 13.
[ 9464.148958] kexec: Waking offline cpu 14.
[ 9464.148994] kexec: Waking offline cpu 15.
[ 9464.149030] kexec: Waking offline cpu 17.
Instrumenting this piece of code revealed that the cpu_up() operation actually
fails with -EBUSY. Thus, only the primary threads of all the cores are online
during kexec, and hence this is a sure-shot receipe for disaster, as explained
in commit e8e5c2155b (powerpc/kexec: Fix orphaned offline CPUs across kexec),
as well as in the comment above wake_offline_cpus().
It turns out that cpu_up() was returning -EBUSY because the variable
'cpu_hotplug_disabled' was set to 1; and this disabling of CPU hotplug was done
by migrate_to_reboot_cpu() inside kernel_kexec().
Now, migrate_to_reboot_cpu() was originally written with the assumption that
any further code will not need to perform CPU hotplug, since we are anyway in
the reboot path. However, kexec is clearly not such a case, since we depend on
onlining CPUs, atleast on powerpc.
So re-enable cpu-hotplug after returning from migrate_to_reboot_cpu() in the
kexec path, to fix this regression in kexec on powerpc.
Also, wrap the cpu_up() in powerpc kexec code within a WARN_ON(), so that we
can catch such issues more easily in the future.
Fixes: c97102ba963 (kexec: migrate to reboot cpu)
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
With binutils 2.24, various 64 bit builds fail with relocation errors
such as
arch/powerpc/kernel/built-in.o: In function `exc_debug_crit_book3e':
(.text+0x165ee): relocation truncated to fit: R_PPC64_ADDR16_HI
against symbol `interrupt_base_book3e' defined in .text section
in arch/powerpc/kernel/built-in.o
arch/powerpc/kernel/built-in.o: In function `exc_debug_crit_book3e':
(.text+0x16602): relocation truncated to fit: R_PPC64_ADDR16_HI
against symbol `interrupt_end_book3e' defined in .text section
in arch/powerpc/kernel/built-in.o
The assembler maintainer says:
I changed the ABI, something that had to be done but unfortunately
happens to break the booke kernel code. When building up a 64-bit
value with lis, ori, shl, oris, ori or similar sequences, you now
should use @high and @higha in place of @h and @ha. @h and @ha
(and their associated relocs R_PPC64_ADDR16_HI and R_PPC64_ADDR16_HA)
now report overflow if the value is out of 32-bit signed range.
ie. @h and @ha assume you're building a 32-bit value. This is needed
to report out-of-range -mcmodel=medium toc pointer offsets in @toc@h
and @toc@ha expressions, and for consistency I did the same for all
other @h and @ha relocs.
Replacing @h with @high in one strategic location fixes the relocation
errors. This has to be done conditionally since the assembler either
supports @h or @high but not both.
Cc: <stable@vger.kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
<<
Highlights include a few new boards, a device tree binding for CCF
(including backwards-compatible device tree updates to distinguish
incompatible versions), and some fixes.
>>
|
|
It no longer occurs in Kconfig.
USB: remove CONFIG_USB_DEVICEFS(fb28d58b) leaked remove defconfig.
Signed-off-by: Naoki MATSUMOTO <nekomatu+linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pcibios_penalize_isa_irq() is only implemented by x86 now, and legacy ISA
is not used by some architectures. Make pcibios_penalize_isa_irq() a
__weak function to simplify the code. This removes the need for new
platforms to add stub implementations of pcibios_penalize_isa_irq().
[bhelgaas: changelog, comments]
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Adds pinmux and DT node for Micron (MT29F4G08AB) x8 NAND device present on
am437x-gp-evm board.
(1) As NAND Flash data lines are muxed with eMMC, Thus at a given time either
eMMC or NAND can be enabled. Selection between eMMC and NAND is controlled:
(a) By dynamically driving following GPIO pin from software
SPI2_CS0(GPIO) == 0 NAND is selected (default)
SPI2_CS0(GPIO) == 1 eMMC is selected
(b) By statically using Jumper (J89) on the board
(2) As NAND device connnected to this board has page-size=4K and oob-size=224,
So ROM code expects boot-loaders to be flashed in BCH16 ECC scheme for
NAND boot.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixes: commit 0611c41934ab35ce84dea34ab291897ad3cbc7be
ARM: OMAP2+: gpmc: update gpmc_hwecc_bch_capable() for new platforms and ECC schemes
Though the commit log of above commit mentions AM43xx platforms, but code change
missed AM43xx. This patch adds AM43xx to list of those SoC which have built-in
ELM hardware engine, so that BCH ecc-schemes with hardware error-correction can
be enabled on AM43xx devices.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A slightly larger set of fixes than we'd like at this point in the
release. Hopefully our very last batch before 3.15:
OMAP:
- Fix boot regression with CPU_IDLE enabled
- Fixes for audio playback on OMAP5
- Clock rate setting fix for OMAP3
- Misc idle/PM fixes
Exynos:
- Removal of a couple of power domains to work around issues with
access when they are powered down
- Enabling missing highspeed-i2c driver to make MMC regulators work
- Secondary CPU spin-up fix for 4212
- Remove MDMA1 engine to avoid conflicts on secure mode platforms
- A few other DT fixes
Marvell:
- PCI-e fixes for clocks and resource allocation
plus a few other smaller fixes, add a MAINTAINERS entry for reset
drivers, etc"
* tag 'fixes-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
MAINTAINERS: Add reset controller framework entry
ARM: trusted_foundations: fix compile error on non-SMP
ARM: at91: sam9260: fix compilation issues
ARM: mvebu: fix definitions of PCIe interfaces on Armada 38x
ARM: imx: fix error handling in ipu device registration
ARM: OMAP4: Fix the boot regression with CPU_IDLE enabled
ARM: dts: Keep LDO4 always ON for exynos5250-arndale board
ARM: dts: Fix SPI interrupt numbers for exynos5420
ARM: dts: fix incorrect ak8975 compatible for exynos4412-trats2 board
ARM: OMAP2+: Fix DMA hang after off-idle
ARM: OMAP2+: nand: Fix NAND on OMAP2 and OMAP3 boards
ARM: dts: Remove g2d_pd node for exynos5420
ARM: dts: Remove mau_pd node for exynos5420
ARM: exynos_defconfig: enable HS-I2C to fix for mmc partition mount
ARM: dts: disable MDMA1 node for exynos5420
ARM: EXYNOS: fix the secondary CPU boot of exynos4212
ARM: omap5: hwmod_data: Correct IDLEMODE for McPDM
ARM: mvebu: mvebu-soc-id: keep clock enabled if PCIe unit is enabled
ARM: mvebu: mvebu-soc-id: add missing clk_put() call
ARM: at91/dt: sam9260: correct external trigger value
...
|
|
Use pci_is_bridge() to simplify code. No functional change.
Requires: 326c1cdae741 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Requires: 1c86438c9423 PCI: Add new pci_is_bridge() interface
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
Use pci_is_bridge() to simplify code. No functional change.
Requires: 326c1cdae741 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Requires: 1c86438c9423 PCI: Add new pci_is_bridge() interface
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use pci_is_bridge() to simplify code. No functional change.
Requires: 326c1cdae741 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Requires: 1c86438c9423 PCI: Add new pci_is_bridge() interface
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use pci_is_bridge() to simplify code. No functional change.
Requires: 326c1cdae741 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Requires: 1c86438c9423 PCI: Add new pci_is_bridge() interface
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Node usbhshost is supporting pinctrl, so the deprecated
quirk call can be removed.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes audio support for omap3-lilly-a83x.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add modem device tree data to Nokia N900's DTS file.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Tested-By: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add SSI device tree data for OMAP3 and Nokia N900.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Tested-By: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The current entry prevents system from idling if
the hwmod is defined in the .dts file so let's
change the idlemodes.
Note that we probably don't have SYSC_HAS_EMUFREE
or SYSS_HAS_RESET_STATUS either. If we do, those
can be added later on.
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
TROUT_CPLD_BASE needs the IOMEM() treatment to avoid warnings
from the read/writeb functions.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/soc2
Merge "Keystone SOC updates part2 for 3.16" from Santosh Shilimkar:
- Removal of now un-necessary reset machine code
- dts updates for keystone reset driver
* tag 'keystone-soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: configs: keystone: enable reset driver support
ARM: dts: keystone: update reset node to work with reset driver
ARM: keystone: remove redundant reset stuff
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
A few drivers for Zynq peripherals made it into mainline recently.
Enable them in the defconfig. The following devices are enabled:
- Cadence Macb Ethernet controller
- Cadence I2C controller
- Arasan SDHCI
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
early_root_info_init() is now deprecated in favor of info in ACPI. Add a
note to that effect. Also, clean up the code a bit.
There is no functional change.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
due to enabling
-- CONFIG_REGULATOR
-- CONFIG_REGULATOR_ACT8865
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[nicolas.ferre@atmel.com: move added entries to proper location within file]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Since mis-order issues have been solved, we can cleanup redundant
definitions that already have defaults in <acpi/platform/acenv.h>.
This patch removes redudant environments for __KERNEL__ surrounded code.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
<asm/acpi.h>
There is a mis-order inclusion for <asm/acpi.h>.
As we will enforce including <linux/acpi.h> for all Linux ACPI users, we
can find the inclusion order is as follows:
<linux/acpi.h>
<acpi/acpi.h>
<acpi/platform/acenv.h>
(acenv.h before including aclinux.h)
<acpi/platform/aclinux.h>
...........................................................................
(aclinux.h before including asm/acpi.h)
<asm/acpi.h> @Redundant@
(ACPICA specific stuff)
...........................................................................
...........................................................................
(Linux ACPI specific stuff) ? - - - - - - - - - - - - +
(aclinux.h after including asm/acpi.h) @Invisible@ |
(acenv.h after including aclinux.h) @Invisible@ |
other ACPICA headers @Invisible@ |
............................................................|..............
<acpi/acpi_bus.h> |
<acpi/acpi_drivers.h> |
<asm/acpi.h> (Excluded) |
(Linux ACPI specific stuff) ! <- - - - - - - - - - - - - +
NOTE that, in ACPICA, <acpi/platform/acenv.h> is more like Kconfig
generated <generated/autoconf.h> for Linux, it is meant to be included
before including any ACPICA code.
In the above figure, there is a question mark for "Linux ACPI specific
stuff" in <asm/acpi.h> which should be included after including all other
ACPICA header files. Thus they really need to be moved to the position
marked with exclaimation mark or the definitions in the blocks marked with
"@Invisible@" will be invisible to such architecture specific "Linux ACPI
specific stuff" header blocks. This leaves 2 issues:
1. All environmental definitions in these blocks should have a copy in the
area marked with "@Redundant@" if they are required by the "Linux ACPI
specific stuff".
2. We cannot use any ACPICA defined types in <asm/acpi.h>.
This patch splits architecture specific ACPICA stuff from <asm/acpi.h> to
fix this issue.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This is a merge of big firewire audio stack updates by Takashi Sakamoto.
|
|
Commit e71246a23acbc89e9cb4ebf1558d60e65733479f changes psci_init from a
function returning a void to an int, but does not change the non
CONFIG_ARM_PSCI implementation to return a value, which causes a compile
warning. Just return 0.
Cc: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-next
Changed for the 3.16 merge window.
This includes KVM support for PSCI v0.2 and also includes generic Linux
support for PSCI v0.2 (on hosts that advertise that feature via their
DT), since the latter depends on headers introduced by the former.
Finally there's a small patch from Marc that enables Cortex-A53 support.
|
|
Enable reset driver support in order to have opportunity
to reboot SoC by watchdog and by software.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[santosh.shilimkar@ti.com: Fixed the subject line]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
The pll controller register set and device state control registers
include sets of registers with different purposes, so it's logically
to add syscon entry to be able to access them from appropriate places.
So added pll controller and device state control syscon entries.
The keystone driver requires the next additional properties:
"ti,syscon-pll" - phandle/offset pair. The phandle to syscon used to
access pll controller registers and the offset to use
reset control registers.
"ti,syscon-dev" - phandle/offset pair. The phandle to syscon used to
access device state control registers and the offset
in order to use mux block registers for all watchdogs.
"ti,wdt-list" - option to declare what watchdogs are used to reboot
the SoC, so set "0" WDT as default.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
Remove reset stuff in flavour of using keystone reset driver:
driver/power/reset/keystone-reset.c
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
When running as a dom0 in PVH mode, foreign pfns that are accessed
must be added to our p2m which is managed by xen. This is done via
XENMEM_add_to_physmap_range hypercall. This is needed for toolstack
building guests and mapping guest memory, xentrace mapping xen pages,
etc.
Signed-off-by: Mukesh Rathor <mukesh.rathor@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
Nothing was using the method and there isn't any need for this hook. This
leaves smp_cpus_done() empty for the moment.
As suggested by Paul Bolle <pebolle@tiscali.nl>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
With inlined uaccess functions we always need the mvcos facility.
Checking at each inline place if mvcos is available would make the
inlining of get_user/put_user pointless.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Add -fno-delete-null-pointer-checks to CFLAGS for the code in
arch/s390/boot. Without the option a compressed kernel built with
gcc 4.9 won't boot.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Analog to git commit 28b92e09e25bdc0ae864b22eacf195a74f861389
first cast tk->wall_to_monotonic.tv_nsec to u64 before doing
the shift with tk->shift to avoid loosing relevant bits on a
32-bit kernel.
Cc: stable@vger.kernel.org # 3.13+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Delete unnecessary local variable whose value is always 0 and that hides
the fact that the result is always 0.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression ret;
expression e;
position p;
@@
-ret = 0;
... when != ret = e
return
- ret
+ 0
;
// </smpl>
[heiko.carstens: turn prepare_cpu_buffers into a void returning function]
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
